Search Documents

By G. R. Corbett

Between 1977 and 1984, No. 26 Colliery, at Glace Bay in the Sydney Coalfield, suffered from a series of 37 rock/gas outbursts. These events were characterized by the complete pulverization of a sandstone which was propelled into the mine roadway and an associated release of methane gas. The events began to appear at a depth of 700 m and increased in intensity and damage to the excavation as the mining depth increased. At the time of the closure of No. 26 Colliery (as a result of an unrelated fire), these outbursts were the subject of intensive investigation. Although No. 26 is now closed, there is concern that similar events could appear at Phalen Colliery where current development work is proceeding at a depth close to the 700 m threshold. Past investigations into rock/gas outbursts included studies of in situ stresses, the simulation of outburst events in the laboratory, investigations into the potential for destressing an& degassing of problem sandstone and the development of numerical models to assist in the design of openings in outburst prone ground. However, despite this work, methods of predicting outburst conditions are presently limited to examination of probe hole cores for core discing, and methods of working under such conditions are limited to boring and firing and using volley firing techniques to initiate any outbursts while workers are safely out of the heading. During this investigation of worldwide occurrences of this phenomena, literature obtained suggested that outbursts might generate microseismic precursors. An intrinsically safe (IS) microseismic monitoring system was designed and developed based on CANMET's rockburst monitoring system currently in use in hardrock mines, and installed in a development roadway at the deepest extent of the Phalen Colliery. The system will record microseismic activity associated with development work to try to identify characteristic precursors of outburst-prone conditions. This paper describes the steps taken to identify a microseismic system suitable for use at Phalen colliery, of which part of the requirement was that it be IS and approved for use in the Sydney Coalfield. The modifications to the selected system are described, along with its capabilities and the preliminary results of its performance over the first few months of use.

Jan 1, 1994

By Matt Leeming

Several of the underground mines in the UK require a significant number of cable bolts to be installed, remedially, to control worsening roadway conditions. Often the access is limited and the only power source is compressed air. Machines for this duty are generally designed to perform with 100 psi but regularly only half of this is available. This paper seeks to outline the difficulties this situation causes the Rock Bolting Engineer, highlight the technical requirements for a machine of this type to succeed and detail a solution offered by our engineers.

Jan 1, 2007

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

By Nikolay Boykov

Subsurface imaging technologies are part of the electromagnetic (EM) geophysical methods. EM technologies such as radio imaging method (RIM), ground penetrating radar (GPR), and drill string radar (DSR) have great application potentials in the mining industry. However, the success for applying the EM methods to subsurface observations is largely dependant on the correct evaluation of the electrical properties (i.e., resistivity and dielectric constant) of the rocks in the domain of interest. The depth of penetration of the EM signal in coal, as well as the electrical contrast between coal and subsurface boundary rocks or anomalies, are critical parameters for any successful radar system. Based on the measured electrical properties of the coal seam, the proper operating frequency of the radar system must be chosen in order to successfully detect features such as the coal-roof rock boundary, dykes, and voids ahead of mining. The electrical properties of the rocks in a coal seam are frequency dependent. Even though there has been a great advancement in the hardware and data processing software in the past twenty years, there have not been many examinations of the high-frequency properties of coal measure rocks. In this paper, the laboratory setups, the testing procedure, and case studies will be presented for a wide spectrum of frequencies for coal measure rock samples collected from various US coal fields. Tests have been conducted to study the different conditions, including moisture content, that affect the EM properties.

Jan 1, 2006

By Rob Thomas

Strata management is a critical and now necessary requirement in the New South Wales underground coal mining industry. As a formal and structured process, strata management allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a controlled manner. In its application, strata management therefore enables operators to identify and control geotechnical hazards and the risks they pose to the mining operation, including risks to personnel safety and mine production. The paper considers recent developments in strata management in the New South Wales underground coal mining industry. Points covered include the statutory requirements stipulated in the Coal Mine Health and Safety Regulations, Geotechnical Hazard Plans, tiered support plans, the Authority to Mine concept, Trigger Action Response Plans and monitoring. Several successful and unsuccessful case studies are included which make specific reference to roadway development and longwall retreat and in doing so, the unique demands imposed by these two different aspects of the mining operation on strata management.

Jan 1, 2007

By Jin He

Based on the simple-beam theory, a stress analysis model was established for undermining in multiple seam strip-pillar mining when the strip pillars were not columnized; the effects of various mining factors (e.g., mining depth, inter-burden thickness, recovery ratio, etc.) on inter-burden stability were analyzed; the changes in inter-burden stress distribution were investigated; and the important role that the inter-burden spacing and the mining width of the lower seams on inter-burden stability was studied. Finally, the actual practice used in Feng Feng Mine area was used as an example to demonstrate the rational mining width for a fixed mining depth.

Jan 1, 2006

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By Paul Singh

Blasting is an integral part of mining activity and is an inherently destructive process. The quality of the rock mass in which an excavation is being driven has a strong influence on the level of dynamic forces to which the rock can be subjected and sustain damage. Though each specific rock mass occurrence is unique, yet there are common rock mass features which influence the outcome of controlled blasting in a similar way. A field study was conducted which involved assessment of blast damage at several operating mines and blasting of small scale models. The effects of block size and strength, joint parameters, ground water, weathering of rocks and rock mass rating on the results of controlled blasting have been investigated and discussed in this study. The influence of number and thickness of weak layers on overbreak control has been discussed in the light of practical data. Critical particle velocity ranges for damage to rock masses with different qualities have been outlined. An approach for the judicious design of perimeter hole pattern and charge concentration has been proposed.

Jan 1, 2007

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Wenbing Guo

The stability of strip pillar is the key to successful strip pillar mining. In analyzing the stability of the strip pillar, the width of yield zone must be determined. The determination of the width of yield zone has been an important subject for researchers. In this paper, the numerical method was used to study the relationship between the width of yield zone in strip pillar and coal recovery ratio. The results showed that as the recovery ratio increases, the width of yield zone increases exponentially. Accordingly, the formula for determining the width of yield zone was updated and the effect of changing coal recovery ratio on strip pillar deformation is presented.

Jan 1, 2006

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By Stephen R. Iverson, Jeffrey C. Johnson, Donovan J. Benton, Michael J. Raffaldi, Lewis A. Martin

"The NIOSH ground control safety research program at Spokane, Washington, is exploring applications of photogrammetry to rock mass and support monitoring. This paper describes two ways photogrammetric techniques are being used. First, photogrammetric data of laboratory testing is being used to correlate energy input and support deformation. This information can be used to infer remaining support toughness after ground deformation events. This technique is also demonstrated in a field application. Second, field photogrammetric data is compared to crackmeter data from a deep underground mine. Accuracies were found to average 8 mm, but have produced results within 0.2 mm of true displacement, as measured by crackmeters. Application of these techniques consists of monitoring overall fault activity by monitoring multiple points around the crackmeter. A case study is provided in which a crackmeter is clearly shown to have provided insufficient information regarding overall fault ground deformation. Photogrammetry is proving to be a useful ground monitoring tool due to its unobtrusiveness and ease of use.INTRODUCTIONNIOSH Mine Safety ResearchPhotogrammetry systems have been implemented by the National Institute for Occupational Safety and Health (NIOSH) as part of its ground control research to improve mine safety. Conventional monitoring of ground movement has typically focused on movement of a few discrete points that are marked or anchored to instruments. Loss of a designated point or anchor, or the ability to identify a stable point in an unstable area, have often frustrated monitoring efforts. NIOSH researchers are using photogrammetry to conduct full-field measurements of rock surfaces underground. Periodic measurements of the entire surface of a ramp allow patterns of displacement to be observed. Full-field measurements provide much more insight into ground behavior than point measurements.BackgroundPrevious work by Benton, et al. (2014) discussed laboratory calibration and verification testing of two photogrammetry systems being used by NIOSH researchers. Both systems utilize stereoscopic image pairing techniques for photogrammetric reconstruction. This paper discusses how a laboratory system was used to conduct volumetric analyses of testing of shotcrete panels with varying types of reinforcement. The laboratory system was found to be accurate to within 2 mm. Additionally, a field photogrammetry system was found to produce linear measurements within 1 mm of known lengths in laboratory conditions. This system is currently being used at a deep underground mine to observe ground support conditions and deformations that have occurred. This paper discusses comparison of preliminary volumetric measurements of rib deformation to laboratory tests, as well as comparison of the field system against a crackmeter installed across a fault surface where it intersects the ramp."

Jan 1, 2015

By Erik Westman

Coal bumps remain one of the industry?s most devastating but least understood phenomena. If changes to the internal conditions of the rock mass could be observed there is hope that bumps could be forecasted. Seismic tomography has been used over the past 25 years in an attempt to image these changing conditions in the vicinity of the longwall face. This paper describes the history and practical considerations of using seismic tomography in bump-prone coal mines. The implementation of seismic tomography at six different longwall mines will be described along with lessons learned. Early studies used mining independent sources of seismic energy, including explosives and sledgehammers. Subsequently more operator friendly sources, such as the mining equipment itself and mining-induced seismicity, were used. Seismic energy sensors have been placed in gateroads and on the surface above the mine. Each of these configurations has associated advantages and disadvantages. Although the results obtained have been encouraging, the application of seismic tomography to monitoring a bump-prone longwall face is still immature. The ultimate goal of clearly imaging changing stress conditions in the longwall panel in a manner that does not inhibit mining operation is still distant, yet drawing nearer. When this goal is achieved, the industry will have a capable tool for identifying locations where bumps are imminent.

Jan 1, 2008

By Keith Heasley

In many practical situation where the LaModel program in used to analyze the mechanical response and failure of the mining environment, there are very few actual field measurement from the site available for deriving the appropriate input parameters. For coping with this typical lack of field data, this paper presents some recommended calibration techniques derived from on an in-depth understanding of the laminated model formulation and from many years of experience applying LaModel to practical situations. For each of the critical input parameters (rock mass stiffness, gob stiffness and coal strength) in LaModel, a specific calibration technique is recommended and presented along with the justification for the technique and some appropriate derivations/equations for assistance. It is hoped that this frank discussion of recommended calibration techniques can help novice LaModel user develop better models and can initiate a discussion among rock mechanics experts on how to improve upon the presented techniques.

Jan 1, 2008

By David Bigby

Rock Mechanics Technology has developed an intrinsically safe remote reading telltale system which allows up to 4 sets of 100 dual height, water diverting telltales in a mine roadway to be remotely monitored from a surface PC. The system has US MSHA approval and European ATEX approval for use in gassy mines. A successful full-scale application of the system employing 67 telltales was completed in a 1300m long maingate roadway during retreat of 183.0 longwall panel at West Mine in Germany between June 2001 and October 2002. During panel retreat a number of "teething" problems associated with the system were identified and resolved, the chief problem being associated with cable connection corrosion due to the unforeseen use of sprayed calcium chloride in the roadway. This paper describes the experience of employing the system at the colliery from the perspective of both the user and the manufacturer, and the improvements and developments which have resulted. The paper also presents examples of roof movement data recorded by the system, including data from behind the retreating longwall. The high resolution and data recording rate possible has resulted in particularly interesting information on roof behavior within the longwall front abutment area and behind the face. The paper also describes a series of new transducers and extensometers for the mining industry which employ the same physical principles and similar electronics to the remote reading telltale system. These have been applied in a variety of mining and tunneling environments worldwide over the last two years.

Jan 1, 2003

By Thomas A. Bailey

Since the advent of longwall mining, various methods and materials have been used during relocation to control the intrusion of the gob in the shield/panline area. (figure 1) Controlling this gob is critical to ensuring a safe, speedy, and productive longwall move. An uncontrolled gob can cause a number of problems, from increased worker exposure to entrapment of equipment to lost production. With an eye toward worker safety and increased productivity, several different methods have been developed to minimize gob intrusion. This presentation will take a look at the history and development of longwall ?screens? and ?mesh?, from chain-link fencing to high-modulus polyester geogrids. The benefits and advantages of these developments will be defined. Since 1994, longwall coal mines have used polymer geogrids during longwall recovery to control intrusion of gob material into the shield/pan line area. As described by Brandon and Collins (1996) in their paper presented at the 15th Ground Control Conference in Golden, CO., mines had used various forms of support, such as welded wire mesh, chain-link fencing, wooden cribbing, props, and steel cable to accomplish this. These methods worked, but were labor-intensive, slow, and provided varying degrees of gob stoppage. Although a few mines still use chain-ink fencing to control the gob, longwall coal mines have generally settled on polyester geogrids to control gob and roof and these mines have been instrumental in providing input in order to develop and improve these geogrids products. he trend during the past twelve years has been to incorporate stronger grids and to eliminate auxiliary reinforcements, such as steel cables and nylon or polyester webbing. A job that once required heavy steel cables, props, and fencing is now accomplished with strong, lightweight, high-modulus polyester grids. When we discuss high-modulus grids, we refer to the ratio between load and strain, as illustrated in figure 2. These grids are woven or knitted from yarns that have been pre-stressed. When these grids come under load, they pick up the load more quickly. This allows less deformation in, in this case, the mine roof. The same principle applies when these grids are used to control the ribs. With less elongation, the grids will hold rib material tighter, thereby keeping travel ways more open.

Jan 1, 2006

By David Dye

Good morning, everyone, and thanks Syd for that fine introduction. I am honored to be here to help you celebrate 25 years of advancement and success in the important field of ground control. I would also like to recognize Dr. Peng for his significant contributions in longwall mining and ground control. His contributions have had a major impact on improving safety and reducing fatalities in America?s mines. Thank you, Dr. Peng, for the important work you have carried on throughout the years. Many miners are alive today because of your dedicated work to protect them.

Jan 1, 2007

By Gennaro Marino

Documented case histories are studied where data were found on the initial collapse of the overburden above the longwall panels. Under this scenario, the most controlled conditions exist for assessing the span capacity of the overburden (i.e., before failure the roof spans to fin coal abutments on two to all four sides). In an attempt to correlate theory to field observations, data are used on the overburden lithology, and the depth, width, and face advance of the panel, as well as, the subsidence conditions noted on the surface. The subsidence measured on the surface is used to determine when complete failure in the over- burden rock has occurred.

Jan 1, 1987