Search Documents

By Dakota D. Faulkner

Cable bolts have been very effective in mine ground control. Non-tensioned and tensioned cable bolts are now used for both primary and supplemental bolting (Suder, 2001; Mirabile, 2010). In the United States, cable bolts are typically installed in either 1 or 1-3/8 in. (25 or 35 mm) diameter drill holes and, if point anchored only, are utilized with 4 - 5 equivalent feet (1.2 - 1.5 m) of resin. Cable bolts can be tensioned by various methods such as using an expansion shell mounted on the cable or post-tensioned with a hydraulic cable tensioning unit. In recent years there has been a desire to completely encapsulate the cable bolt for corrosion protection. Fully encapsulating a cable bolt with traditional resins can be very difficult. Keystone Mining Services, LLC (KMS) and Jennmar Corporation have developed a new cable bolt that can be fully encapsulated during installation or post-installation with polyurethane (PUR). The Fully-Grouted Cable Bolt (FGCB)* is equipped with a special head that allows the injection of PUR up through the cable bolt head and cable strands, completely encapsulating the cable and filling the drill hole. Although the FGCB was initially developed to fully encapsulate the cable for corrosion protection, it was also found that by modifying the cable bolt head and injection pressure, PUR could be injected into cracks and fissures of the strata to stabilize the roof. This paper details the development of this system and three underground applications under different ground conditions.

Jan 1, 2012

By T. N. Singh

An evaluation was made on the cavability of the roof formation of Dishergarh seam including caving sequence, caving span, and load on powered support.

Jan 1, 1994

By Yingxin Zhou

Virtually every coal seam in Appalachia will at some time be subject to multi-seam interaction (Wu et al, 1987). Many such problems result from seams which lie in close proximity or have split and lie within thirty feet vertically of one another. Existing techniques for multi- seam design have concentrated on conditions where the entire inner burden is not the failing member and are unsuitable for ultra-close multi-seam design. Structural integrity of the inner burden must be maintained if two superimposed seams are to be mined separately and under- standing possible failure mechanisms of the inner burden is an essential first step in the design process.

Jan 1, 1989

By Tristan H. Jones

Beginning in 1987, miniature dataloggers approved by the Mine Safety and Health Administration (MSHA) were publicly available for sale. The principal among these was the model CR21XQM, manufactured by Campbell Scientific, Inc. These dataloggers had been tested and were deemed permissible by MSHA and thus could be installed in the return air of an underground coal mine. In 1996, production of all permissible Campbell Scientific dataloggers ceased due to lack of sales. Data collection with these dataloggers has been a staple of ground control research in the United States for decades, and, without them, or a replacement, the capability to monitor ground behavior is severely impacted. Since that time, any party requiring a permissible datalogger has needed to borrow one that was purchased during the production years. In order to fill this technology gap and ensure its own data-gathering capabilities, the National Institute for Occupational Safety and Health (NIOSH) has developed and refined its own miniature data acquisition system (MIDAS). On February 16, 2010, MSHA deemed the MIDAS to be permissible and approved it for use in the return air of an underground coal mine. The MIDAS is an intrinsically safe, 16- or 24-bit datalogger, compatible with a wide range of resistive, single-ended, and differential-type instrumentation. It contains enough data storage memory to operate for over a year with typical data rates and is efficient enough to do this on a single C-sized alkaline battery for that entire period. It is menu-driven and requires no programming knowledge to operate. It supports wireless or hardwired communication for datalogger setup and data download. This paper describes the design, field and laboratory testing, and capabilities of the MIDAS datalogger. While not as fully -functioned as the CR21XQM, it is the only new permissible datalogger available, and there is intent to make it available to the mining industry for purchase.

Jan 1, 2012

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ? Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions ? became the post-event conditions.Search for evidence that either denies or supports the various ? hypotheses.Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006

By Daniel W. H. Su

The importance of incorporating fundamental principles of rock material response and failure mechanics into a pillar strength design model has been demonstrated. To accurately assess pillar strength, a model should account not only for the characteristics of the coal, but also for those of the surrounding strata. The interactions between the pillar and the surrounding roof and floor dictate ultimate pillar strength. Confinement, or the lack thereof, provided by roof and floor frictional end-constraint is one of the most significant factors in the strength of very wide pillars. The best conditions for end-constraint occur with ideally strong roof and floor. In this paper, it will be shown that weak roof and floor may decrease the ultimate pillar strength by as much as 30% compared to ideal conditions. Field observations confirm this pillar strength reduction in the presence of weak roof and floor. Furthermore, rock partings within the coal have a variable effect on pillar strength, depending on the parting strength. A competent shale parting within the coal reduces the effective pillar height, thus increasing the ultimate pillar strength; a weak claystone parting slightly decreases the strength. Imposed load distribution also has a significant effect on pillar strength, such that asymmetric pillar loading, similar to that observed in pillars adjacent to high extraction mining, reduces the ultimate pillar strength below that of equivalent pillars subject to uniform load distributions.

Jan 1, 1997

By Anthony Iannacchione

Coal mine bursts have represented a major hazard for U.S. mining operations for more than 90 years. During this time, many prevention controls have been developed and tested. This paper reviews 11 prevention control techniques. Although coal mine bursts are not common events in most underground coal mines, their occurrence almost always requires a change in mining practice. Over the many years of dealing with these hazards, specialized requirements for layouts and novel extraction sequences have been developed on a site specific basis. The keys to mitigating risks are to properly assess the coal burst hazards and to possess the knowledge and skills to prevent or remediate their occurrence.

Jan 1, 2008

By Jurgen te Kook

State-of-the-art for subsidence calculation are stochastical models. Although these models were successfully used all over the world they have their limitations due to the fact that they are not based on mechanical laws. For example the models did not take the rock mass structure and the rock mass characteristics into account. Therefore in a research program the skills of geomechanical numerical models for subsidence calculation were investigated. A case study shows that numerical models which are in principle based on the elastic theory are suitable for subsidence prediction. Due to the principles of these models the results are not sufficient in the case of multiple seam extraction. More extended geomechanical numerical models like FLAC and UDEC were investigated in further steps of the research work. Up to now large area geomechanical models require unrealistic long calculation times if the level of detail is similar to that of small scale calculations. Due to this it was necessary to implement a simplified description of the rock mass structure and characteristics. Different case studies show that this approach is successfull for subsidence calculation by numerical geomechanical models even for multiple seam extraction.

Jan 1, 2008

By Andre Vervoort

Falls of ground, such as falls of roof and sidewall collapses, are a major cause of fatalities and injuries in South African collieries. Based on information obtained from the accident reports of the various Chief Inspectors of nines, a statistical analysis was conducted covering the period 1970 to 1988. This study shows that the volume of rock in a fatal fall of ground is often quite small. In intersections, fatal falls are on average larger than in roadways and at the face. It was also found that in 36 % of all fatal falls of ground no temporary or permanent support was installed at the site of the accident.

Jan 1, 1990

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By D. Su

This paper presents the details and results of a preliminary investigation into the response of borehole pressure cells (BPCs) in soft coal. Two parallel approaches, laboratory calibration and nonlinear finite element simulation, were adopted for deter- mining the BPC K-factor, which was defined as the ratio of cell pressure change to the corresponding change in external pressure. Results from both the laboratory calibration and the nonlinear finite element simulation revealed a nonlinear response of cell internal fluid pressure to external loading. The K-fact& also is shown to increase with increasing setting pressure and decreasing medium modulus. -Depending on the setting pressure, the K-factor for coal having a Young's modulus of 1.6 x lo5 psi ranges from nearly 1.2 at 2,000 psi of external pressure to 1.485 at 8,400 psi of external pressure. The improved under- standing of BPC behavior leads to the more accurate calculation of BPC K-factor in coal which significantly improves the correlation between pillar pressures measured in underground coal mines and those predicted by nonlinear finite element simulations of these pillars.

Jan 1, 1990

By Haile Manteqi

In longwall coal mines, estimation of roof strata condition, sequence of loading, and supporting requirements are of a high degree of importance, and they are directly related to production and safety. Also, a prediction of the initial caving distance is rather complicated to calculate, because there are many parameters that effect caving process?roof and floor strata conditions, thickness of immediate roof, depth of cover, excavation geometry, and magnitude, and direction of principal stresses. This paper presents the results of 3D numerical modeling of the initial caving mechanism using the finite difference code FLAC3D at the E1 longwall panel of the Parvade 1 underground mine located in the Tabas area in the central part of Iran. The initial caving distance obtained was 10.4 m. Also, the results of numerical modeling have been compared to the analytical methods, such as Peng?s method. The results show good agreement with each other.

Jan 1, 2012

By Hamid Maleki

In this paper, the authors present a review of data gathering programs and stress analyses for improving mine layout designs at BRL mines located near Paonia, Colorado. BRL and other companies have used both longwall and continuous miner methods for the extraction of the Upper D, Upper B, Lower B and C seams from the multiple-seam reserves in the North Fork Valley. Historic mining in the B and C seams has created stress footprints in the neighboring unmined seams compounded by stress transfer from recent longwall extraction in the Upper D Seam. Thus optimum positioning of workings in the remaining reserves requires careful collection of pertinent data and consideration of load transfer from previous workings through remnant abutment pillars. Based on long-term subsidence monitoring, underground mapping and stress analyses, we have confirmed initial load transfer analyses finding mild interactions between the UD and LB workings, and the mining conditions have proven to be good and manageable during the development stage of the LB Seam. This has been achieved through prudent mine planning, prudent positioning of the gateroads in multiple seam workings and support allocations.

Jan 1, 2007

By Sudhir Kumar Kashyap

In underground activities ground control is a challenging problem. It affects safety, production, and efficiency. As per statistics of accident data, ?fall of roof/sides? is one of the major causes of mine accidents. In many cases, our experiences and understanding of soil and rock behavior still fall short of being able to predict how the ground will behave. Presently, empirical approaches to design are widely used in estimating mine support parameters. Under these circumstances, expert judgment plays an important role, and such accidents can be obviated with accurate measurement and optimization of data and analysis using the neuro-fuzzy technique of artificial intelligence. Recently, a neuro-fuzzy hybrid approach has become one of the major areas of interest in engineering fields because it gets the benefits of neural networks as well as those of fuzzy logic systems, and it removes the individual disadvantages by combining them on the common features. Neural network and fuzzy logic technologies have common features, such as a distributed representation of knowledge, the ability to handle data with uncertainty and imprecision, etc., like in ground control. Fuzzy logic technique has tolerance for imprecision of data, while neural networks have tolerance for noisy data. In this paper we have focused an intelligent technique, i.e., neuro-fuzzy technique, to approximate the setting load given to the standing support (props) erected for the purpose of supporting freshly exposed roof during underground mining. We have used twelve input variables of rock parameters, and after having trained using a neural network with a sigmoidal function as an activation function, simulation was done to find the output parameter, i.e., the pre-load (setting load)to be applied on props. Outputs of the neural network were again fed to the fuzzy system together with the twelve parameters, incorporating five triangular membership functions for each parameter. Final optimum output was approximated using the MATLAB program, which was found to be satisfactory. Neuro-fuzzy technique has better performance over individual neural networks or fuzzy logic technique.

Jan 1, 2012