Search Documents

By H. H. Kleizen

The operation range and efficiency of dewatering apparatus are important factors in the selection of an apparatus for a given purpose. In this paper theories are presented allowing to predict these basic characteristics for different dewatering apparatus and compared with experimental and practical data obtained on coal and ore slurries.

Jan 1, 1989

By Stanislaw Siewierski

One of the major problems in the exploitation of deep copper ore deposits in the Legnicko-Glogowski Copper Field is ground control and, in particular, roof control of the headings. The depth of copper deposits ranges from 600 to 1200 m. The parameters of ore-bearing rocks and the surrounding rocks show considerable variance of strength properties along the mining thickness (Fig. 1). The roof of the openings exploitation headings consists of dolomite-calciferous rocks. The roof strata consist of layers, the thickness of which vary from several centimeters to 0.6 m (sometimes to 1.0 m). These strata differ in strength and are characterized by igneous and sedimentary discontinuities. On the basis of studies in structure, properties and geological mining conditions of the roof strata in Polish copper mines, the method of roof classification has been developed. (1) This method uses the stability index "L" of the roof, calculated from [ ] The value of "t" ranges from 0, l to 0,8. Based on the value of "L", four classes of the roof (Table 1) corresponding to different degrees of fall hazard have been developed. The mining of copper ore deposit is carried out by a single lift room-and-pillar mining system or a two-stage room-and-pillar system with roof caving. (3, 4). The single lift room-and-pillar mining system is most often used. It consists in working of the deposit of 2.5 to 4.5 m mining thickness, 150-350 m long mining line, consisting of parallel room faces 6 m wide with pillars 5.7 or 16 m wide. As the mining line advances, cross-cuts joining individual rooms are made, thus forming support pillars 3x5, 7x7, 5x16, and 7x16 m (Fig. 2). The two-stage system (Fig. 3) mines the deposit with rooms 6 m wide into blocks 25 x 35 x 25 x 45 m. During the second step these pillars are worked with rooms and cross-cuts into pillars about 3 x 4 to 4 x 5 m (retreat mining). The pillars are crushed just before the fall of the roof. The maximum opening of workings in the two-step system is about 10 m, i.e. one belt entry and one row of bearing pillars. In single lift room-and-pillar systems it is about 35 m., i.e. three belt entries and three rows of bearing pillars. The support of the headings consists of expansion bolts 1.6-1.8 m installed in a bolting pattern 1.1 x 1.5 m. In both systems the fall step is about 10 m, i.e. the width of a belt and a bearing pillar. The Indications of Rock Mass Pressure Individual Dog Heading Individual dog headings are set wide apart from each other in the unmined ore deposit area where there is no interaction of headings. The indication of rock mass pressure are, in such cases, limited to the deformations and damage of side walls. Radiometric studies of rock mass loosening showed that the maximum range of lifts in side-walls immediately after web was 2 m (4,5). In the course of time the cracked side rocks fall off, thus widening the heading. The morphology of side-walls is influenced by the location of the heading in relation to clump layer/tarry. This layer is characterized by a weak strength and "lubricating" properties. The location of the heading in

Jan 1, 1982

By Wei Bin, Liu Zhe, Liping Xiao, Jichi Bai

The Acid Mine Drainage has characteristics of low pH, high concentrations of heavy metal ions, such as Fe2+, Mn2+, Cu2+ and Zn2+. In this paper, the composite particles that consisted of bentonite and steel slags were used to dispose the Acid Mine Drainage. Bentonite is the mineral materials and can adsorb heavy metal ions excellently. The steel slags are alkaline and industrial solid waste for the treatment of the Acid Mine Drainage. The main influencing factors, such as adsorbent dosages, shaking rates, concentrations of heavy metal ions, temperatures, adsorption time and pH value were studied by the static experiment. Increasing the adsorbent dosages and the concentrations of the heavy metal ions, speeding up the shaking rates, raising the temperatures, extending the adsorption time and improving pH would improve the removal efficiencies of heavy metal ions. Through considering the removal efficiencies and the treatment costs, the optimum reaction conditions for the four kinds of heavy metal ions were obtained. The adsorbent dosage 21 mg/L, the rotational speed 120 r / min, the temperature 25?, adsorption time 100 min and the initial wastewater pH 7. The four kinds of heavy metal ions existed independently in the simulated mine wastewater. The highest initial concentrations of Fe2+, Mn2+, Cu2+ and Zn2+ were 150 mg/L, 100 mg/L, 170 mg/L and 140 mg/L respectively. The removal rates were 93.42%, 92.64%, 93.86% and 95.17% respectively. The determination of the particles’ SEM-EDS Microscopic characterization showed the composite particles could play a part in neutralizing, absorbing and the chemical precipitation. The acidity decreased notably and the heavy metal ions of Fe2+, Mn2+, Cu2+ and Zn2+were adsorbed and precipitated effectively. The research results can extend the practical engineering application of the composite particles.

Jan 1, 2017

By Aydin Shaterpour Mamaghani, Bilgin. Nuh, Engin Dogan, Tayfun Erdogan

"Improved safety and more environmentally friendly operation are basic advantages of mechanical excavation over the drill and blast method. Raise Boring Machines (RBMs) are one of the types of these machines which have recently been increased use in Turkey. The excavated hole with RBM is more stable than other methods and has better air flow, making it ideal for ventilation shafts. This paper is a summary of the performance of a RBM in the Balya PB-Zn Mine in Turkey. Length and diameter of the ventilation shaft are 200 m and 2.4 m, respectively. The geological and geotechnical characteristics of the strata excavated in the mine are first given and later the validity of a model developed to predict the machine performance is discussed. It is believed that the results of this study and the model given to estimate the performance of the RBM will be useful guide for future applications. INTRODUCTION Raise boring technology was developed to meet the demands of the mining industry, but has also found numerous applications in tunneling or infrastructure projects for ventilation purposes. Raise boring machine uses a small diameter drill rod, around 230-350 mm to drill a pilot hole down to the required depth up to around 2000 m. Once the pilot hole has been drilled to the desired depth, a reamer of up to 9 m diameter is attached to the drill rod. The reamer is then pulled back up to the upper level, creating a round shape. Continues operation provides a faster advance rate than other methods. RBMs are suitable both in hard and soft rock. The flexibility in different angles and diameters is a great advantage compared to drill and blast excavation method. RBM creates a shaft with smooth walls which usually does not require lining. The hole is more stable than a drilled and blasted method and has better air flow, making it ideal for ventilation shafts. Raise boring is convenient method in competent rock; however several problems are faced in geological formations where geological discontinuities are dominant. Moreover, assembly and disassembly time may be long in some cases. The performance and operational parameters of the excavating machine should be predicted prior to starting the excavation operations in order to fulfill the economic requirements of the project. In the light of this fact, the main objective of this investigation is to summarize a case study on raise boring machine performance and suggest a new model based on laboratory test results. First, general description of the mine and project are provided. Then, the physical and mechanical characteristics of the samples taken from project area are discussed. In the third section, performance and operational parameters of RBM are investigated to understand the machine behavior in different rock characteristics and also to collect a useful database for further investigation. In the fourth section, a new model for performance estimation of RBM are recommended."

Jan 1, 2016

By John R. Alderman

INTRODUCTION Uranium production in Saskatchewan commenced in 1953 at the Eldorado Nuclear Mine in the Beaverlodge area of North Saskatchewan, followed over the next few years by nineteen other smaller mining operations. Production rose from 453 600 to 2 721 600 kg per annum by 1958. Over supply and the closure of the U.S. market to Canadian uranium led to an equally rapid decline to an annual production which varied from 453 600 to 907 200 kg during the years 1964 to 1976. As the market strengthened there was a resurgence of the Saskatchewan industry and production from one underground and two open pit mines reached 2 809 000 kg in 1980 for a return of 232 000 000 dollars (Table 1). [ ] Future output will be increased by a potential 4 536 000 kg from the Key Lake mine now under construction and scheduled to commence production in 1983. Three other projects are in an advanced stage of planning and are currently in the regulatory review process. Several other prospects are being evaluated. Figure 1 shows the location of uranium mines in Saskatchewan and table 2 illustrates the present status of uranium mines and deposits in Saskatchewan. At present, 1400 workers are employed directly by the uranium mining industry. Saskatchewan has diverse mining conditions ranging from the underground mine of Eldorado Nuclear Limited 1870 m deep with a low grade ore deposit averaging from 0.17-0.20% with extraction by carbonate leaching through an open pit operated by Gulf Minerals with a moderate depth of 110 m and 0.37-0.5% grade to the shallow open pit of Cluff Mining 30 m deep with a very high average ore grade of 7.0%. Extraction at both open pits utilizes acid leach extraction processes, the latter after gravimetric separation. Key Lake mining has commenced development of the next mine to come into production which will have two open pits to a depth of 80 and 175 m with an average 3% grade to be followed by the deep open pit of Canada Wide Mines Ltd. to a depth of 205 m with average grade of 1.5%. One existing mine will transfer its operation from the present open pit to another of slightly higher average grade. From the Saskatchewan point of view, these different operating conditions present varied problems associated with occupational health and safety and concomitant solutions to reducing worker exposure to radiation. REGULATION OF URANIUM MINES In 1946, the Government of Canada enacted the Atomic Energy Control Act which established the Atomic Energy Control Board (AECB) and vested in that board powers to regulate all aspects of uranium mining. In the early years, the AECB relied heavily on provincial occupational health and safety agencies for the surveillance of uranium mining and milling operations, particularly with regard to "conventional" occupational health and safety, the AECB having at the time no specific regulations covering the mining industry. There has been considerable dialogue between federal and provincial governments since, traditionally, occupational health and safety is a provincial jurisdiction. Saskatchewan is strongly opposed to the intrusion of the federal government into the provincial domain, particularly as there is little justification for a federal presence in occupational health and safety in uranium mining and milling. The province does, however, accept the need for federal involvement in certain aspects of the regulation of nuclear industry, for example, international sales, research and security of reserves for domestic use.

Jan 1, 1981

By G. Argyris

A number of important studies, ongoing environment monitoring efforts and mining and road construction projects in the lignite based electrical power production area of Amyntaio ? Ptolemais in North West Greece require an accurate and up to date model of the topography. In recognition of the importance of such a model, a project was initiated by the Laboratory of Mining Information Technology and GIS Applications in the Department of Geotechnology and Environmental Engineering of the Technological Educational Institute of Western Macedonia. A massive surface triangulation model was generated from vector data using an optimized Delaunay based method. Combined with aerial and satellite imagery, the triangulation model provides a complete 3D terrain model of the area characterized by high levels of accuracy, detail and realism. The generated model is easy to modify with new data in order to improve its detail and keep it up to date with ongoing earth moving and development operations in the area.

Jan 1, 2008

By Patrick Oriez, Chris Norris, Alain Mercusot

"Temporary mechanical ventilation is one of the fundamental requirements in guaranteeing a healthy atmosphere in underground construction works in order to protect the health of persons working on the site. It is therefore essential to conceive a system which meets the requirements of the whole of the worksite and for all phases of work which takes into account all aspects pertaining to its design, dimensioning, justification, installation, maintenance and validation. In doing so, the ventilation design and the selected apparatus to be installed shall meet with the degree of health protection and the quality of air of the worksite as defined by the legislation in force in France, through limiting the concentration of the different pollutants associated with the site activities. Consequently, when presenting a mechanical ventilation project, all of the participating parties and especially the contractor make a commitment to guarantee sufficient volumes (or airflow rates) of fresh (non-polluted and oxygenated) air and extracted (polluted) air in order to meet these limitations and maintain them in all conceivable site configurations. This article sets out the most important aspects of the implementation of a ventilation project from the initial design stage through to its application, discussing French legislation, ventilation principles, calculations and techniques with regards to underground construction sites. BASICS OF VENTILATION Mechanical ventilation studies are concerned with all of the site workstations and work phases which are sources of pollution and apply to all zones of the underground worksite with the goal of maintaining the concentration or composition of this pollution below the permitted levels and comply with the following three basic principles which are complementary to one another without being in contradiction. •,The first principle consists in eliminating or limiting as much as possible the emission of any polluting, irritant, or dangerous substances, by specifying appropriate construction techniques and equipment (use of electric motors, combustion engine equipment: filters, tanks, catalyzers, use of less polluting explosives, damping down dust with water or wetting products, damping down and diluting certain gases using water mists). •,The second principle is designed to capture residual polluting substances emitted close to the source in order to prevent them from spreading into the worksite atmosphere (extraction ventilation with ducting up to the source – upstream of the extractor fan – and use of downstream filters before expelling the polluted air to the exterior). •,The third principle involves accompanying the capture of the pollutants with additional blowing ventilation specific treatment of substances dissipated by and distant from the source of pollution (acceleration of the drift air flow in order to confine dust and better capture it, supply ventilation with ducting in order to dilute the gases emitted and discharge them to the exterior)."

Jan 1, 2016

By V. Anthony Cammarota

MINERALS INFORMATION PROGRAM Mineral data collection by the Federal Government actually began in 1882 with an appropriation by Congress to the U.S. Geological Survey (USGS). Although the Bureau of Mines was instituted in 1910, it was not until 1924 that the collection, interpretation, and dissemination of worldwide information on production, consumption, and availability of minerals became the responsibility of the Bureau. The objective of the Bureau's minerals information program is to maintain and provide reliable, timely, and comprehensive data for analysis of national minerals problems. This program is implemented by a staff of specialists who cover about 100 mineral commodities and the mineral industries of 168 countries. Data are also provided on the minerals industry on the State and county level. The specialists analyze information to identify trends and problems, forecast future U.S. and world supply and demand for the nonfuel minerals, and relate trends and developments to their impact on the domestic minerals industry. Data Sources and Publications The primary sources of data concerning the domestic minerals industry are the companies that produce, use, and trade in these minerals. Approximately 60,000 survey forms are sent to industry, on a monthly, quarterly, semiannual, or annual basis, to obtain the data. Domestic trade data are provided by the Bureau of the Census, U.S. Department of Commerce. Information on mineral developments abroad is developed by Bureau specialists from mineral reports supplied by U.S. embassies worldwide, from primary source documents, from a review of the technical mining literature, and from onsite mine and plant visits in foreign countries. The information is disseminated through a number of Bureau publications: "Mineral Industry Surveys" provide aggregated data on a monthly. quarterly, or semiannual basis to give timely information on the most important mineral commodities. "Mineral Commodity Summaries," published each January, provides preliminary annual data on supply and demand and discusses significant events of the previous year. The final data are published later in the "Minerals Yearbook," which is the definitive historical record for mineral statistics. "Mineral Facts and Problems," an encyclopedic work issued every 5 years, covers industry structure, technology, supply-demand analysis. economic factors, reserves, and forecasts of U.S. and world demand for individual commodities. "Mineral Perspectives" and "Mineral Issues" cover important international mineral developments and significant issues of current U.S. policy as they relate to minerals. Discussions and analyses of mineral trends and developments also appear in other Bureau publications, such as "Minerals and Materials" and "Information Circulars." These publications provide the basis for analysis and policy determinations by the Bureau and by virtually every Federal agency concerned with minerals, defense issues, the national economy, and foreign relations. The data are also used by industry in planning capital investments in mines and processing plants, by financial analysts, by U.S. delegations in their work with international commodity groups, and by a host of other minerals related organizations. Data Bases The data bases used by the specialists for preparing publications or in response to a continuous stream of inquiries include both those that contain individual commodity data from respondents, and those that are summary data bases on production, trade, capacity, employment and a number of other minerals-related items, not all of which are derived from data reported to the Bureau of Mines. The data bases maintained on the mainframes are not accessible by non- Bureau users. A 10-year data base of supply- demand data, published each year as an update of tables that appear for each commodity in Mineral Facts and Problems, is available on a floppy

Jan 1, 1987

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thorough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield revenues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equipment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Arranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that, the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1990

By J. L. Chakravatti

INTRODUCTION Mining of uranium does not differ, in many respects, from the mining of other metals; the ore must be drilled, blasted and transported in an underground or surface mine. Underground mining proceeds by the continuous development and advancement of a network of passages and rooms or stopes from which ore is excavated. As in most mines, rock conditions and ore grades in uranium deposits vary from area to area and between different mines. For mineral benefications of this ore in the mills, use is made of various chemicals, often with toxic or hazardous properties.1 As well as the need to control the more conventional hazards associated with any mining and milling operation, special care needs to be exercised in the mining and milling of uranium because of the radioactive nature of the ore. This requires that we examine closely the radiation hazard areas encountered in the mining and milling of uranium, with the broad overview of some of the basic facts in the radiation hazard control programme. To place the hazard in its proper perspective, we require recognition, evaluation and control of those factors arising in and from the workplace which may cause sickness, impaired health and affect the well being among workers or citizens of the community. The radiation environment in uranium mine is complex and variable. Although uranium ore is only mildly radioactive, it naturally contains a complex mixture of radioactive isotopes. Workers are exposed to external gamma radiation, to some beta radiation and to airborne radon, radon daughters and ore dust. All of these types of exposures warrant considerations in formulating control procedures but, in general, radon daughters are known to present the dominant risk. The basis of dose limitation in radiological protection is risk limitation. Long-term epidemiologic studies of United States uranium miners and that of miners in Czechoslovakia indicate that the incidence of lung cancer can be accounted for by a linear relationship with exposure to radon decay products.2 On the basis of this proportional exposure-risk relationship, a risk coefficient for lung cancer in the range of 1-5.10-4 WLM-1 during the total lifetime, has been estimated by UNSCEAR3 and other researchers. It should be noted that this risk coefficient includes the excess lung cancer risk from external gamma radiation in mines and from other carcinogenic chemical effects, if any, to which the miners are normally exposed during their underground work. It also takes into regard the possible synergistic influences. This paper reviews the occurrence of radiation and its control factors and the development of engineering design features for the environmental control at Denison Mine. NATURAL URANIUM SERIES Uranium is the most common element in the Earth's crust. It is widely distributed in nature in all rocks and is readily measurable in the sea. Hence, radon gas is universally produced in every part of the globe. Mining is patently confined to ores containing more than half a kilogram, or so, per tonne of uranium unless it is combined with other marketable metals. Uranium-238 is the first element in the uranium series. In all, there are 13 radioactive decay products of 238U (Fig. 1), ending up as a stable isotope of Lead-206. The whole basis of the radiological hazards associated with the mining and milling of uranium is dependent on the behaviour of these isotopes during each phase of the process.

Jan 1, 1981

By M. H. Kahn, F. C. Bond, K. J. Edmiston

Comminution of various materials can be achieved in grinding equipment by nipping, impact, attrition, or a combination of these actions. Pna mills also known as edgerunners, chasers, and mullers-are classified as a nipping machine. The essential features of this type of grinding machine are rollers or mullers that turn on a horizontal axis while rating on the bed of material in the pan. Ploughs are used to direct the unground material to the center of the pan. Grinding may be accomplished wet or dry. Aritres, Chilean mills, and Huntington mills are types of pan mills. Ring roll and ring Ml mills, another type of nipping machine, were developed for grinding smaller particles of intermediate hardness to product sizes of about 100 pm. They were designed to attempt to reduce the cost of similar size reduction in ball mills and have been widely used to pulverize coal for power-plant facilities. Impact Machines Grinding machines that can be classified as impact mills include: hammer, cage, centrifugal, vibratory, pin, and stamp mills. The distinctive feature of an impact mill is that it has a fast-moving part that transfers some of its kinetic energy to the material particles by direct contact so that internal stresses are created in the particles. The Reitz Disintegrator is an example of an impact mill. It has rigidly mounted hammers attached to a vertical shaft that rotates in close proximity to horizontally mounted screens. The feed pulp enters parallel to the vertical shaft, and may have a solids content of from 40

Jan 1, 1985

By John C. Gould

GENERAL DESCRIPTION The Climax mine is located 161 km (100 miles) southwest of Denver on Fremont Pass astride the Con¬tinental Divide. Climax employs 2800 people to pro¬duce 42 670 t/d (47,000 stpd) of molybdenum ore. The Storke level, the main underground level, produces 19 970 t/d (22,000 stpd); the 600 level, the lowest ac¬tive underground area, produces 7260 t/d (8000 stpd); and the open pit presently produces 15 430 t/d (17,000 stpd), Fig. 1. A panel caving method is possible because of the favorable geology and geometry of the Climax ore body. Geology The Climax deposit is composed of three separate ore bodies formed in a massive Tertiary stockwork which penetrates Precambrian granites and schists. The ore bodies are elliptical in plan with overall dimensions of 914 x 1219 m (3000 x 4000 ft). In section the ore bodies are arcuate with an overall height of 457 m (1500 ft), although the depth is not firmly ascertained. Ore grade decreases rapidly into a highly siliceous cen¬tral core and more gradually toward the outer bounda¬ries of the deposit. The mineralization is relatively continuous in the ore zone and contains few dilution-causing waste inclusions. Molybdenite is contained in pre-ore fractures which were largely recemented during the three mineralization pulses. Postore fractures, with a spacing of a few inches to several meters (feet), render the deposit amenable to caving when it is undercut. The peripheral rock caves similarly to the ore, but the central core is competent and is difficult to cave. Caving Feasibility Successful caving action requires an undercut area of approximately 122 by 122 m (400 by 400 ft). When the undercut area exceeds this minimum distance, the arching effect is lost, and the ore column collapses. Ore extensions from the main cave area less than 122 m (400 ft) wide usually cannot be caved. Waste or low¬grade areas within the deposit can be left if they are large enough to carry weight around openings passing through them. Experience indicates that these areas should be over 30 m (100 ft) in length and width. Smaller unprofitable units of waste, such as postore dikes, are mined to avoid weight problems and result in ore dilution. Successful caving and ore recovery are dependent upon timely ore removal from the undercut zone because columns of immobile ore inhibit caving and concentrate weight onto the underlying workings. Climax experience indicates that a finger (drawpoint) spacing* averaging 10.4 m (34 ft) yields an excellent caving action and a 92.5% ore recovery at the estimated grade. An additional 15% of the ore is recovered-at a diluted grade (Fig. 2). Mine Layout The slusher drift is the primary production facility (Fig. 3). The ore is undercut and caved into the fingers,

Jan 1, 1982

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The paper evaluates the attenuation behavior of acoustic emission (AE) signals in four different materials used in marine environments. The study aims to identify materials with the highest and lowest AE signal attenuation, providing insights into wave propagation and structural monitoring in deep-sea mining applications.

Dec 1, 2023

By David B. Campbell

INTRODUCTION This submission was made to the Royal Commission of Inquiry into uranium mining in British Columbia. It discusses the stability of waste rock piles that might be developed in conjunction with uranium mining and the control of leachates that might be generated within these waste rock piles over the short and the long term. Short term refers to the interval during which a waste rock pile undergoes either continuous, or alternatively intermittent development, and in general can be considered to extend over the operating life of the mine. Long term refers to the postmining period, i.e. after the ore-body has been exhausted, and mining operations have ceased. Two major classes of waste material are generated in the course of mining and milling operations. Tails, which are the solid waste materials produced by the milling operations commonly exit the mill in slurry form and are stored in tailing retention ponds. Management and control of these slurried wastes are the subject of other papers to the Commission and this conference. In the course of the mining operations, it may be necessary to remove rock materials that are below cut-off grade. That is, ore concentrations within some of the mined rock may be lower than the concentrations which on the basis of economic considerations justifies milling the material. Rock which is removed in the course of the mining operations, but which is below cut-off grade is referred to as waste rock. This waste rock is commonly consigned to a specific area for disposal where it is placed in a mound or pile, i.e. a waste rock pile. Ore concentrations within the waste rock may vary from zero to just below cut-off grade. Since an increase in the market value of uranium could at some time in future result in reduction of the cut-off grade, it follows that waste rock containing ore concentrations slightly below today's cut-off grade could become ore grade rock at some time in future. For this reason, the mine operators may deem it advisable to separate waste rock according to grade, and to consign the waste rock to two or more individual waste rock piles. For purposes of clarity and simplicity, this submission treats the stability of waste rock piles and leachate control in a manner which assumes that these potential problems are isolated and separate from other aspects of the mining and milling operations. For many site specific cases, the problem of potential leachate control might be integrated with the tailings management aspect of the project, thereby realizing economic benefits while at the same time reducing the potential for adverse environmental impact.

Jan 1, 1980

By C. O. Brawner

INTRODUCTION My first major involvement on a rock mine slope stability project was in 1966 after I had become a principal of Golder Brawner & Associates in Vancouver, Canada. I received a request from Kennecott to evaluate two serious rock slope failures adjacent to the concentrator on their British Columbia molybdenum property near Alice Arm, BC, which was under construction. A rock slope up to 200 ft* high had been excavated at a design angle of 700. The inspection indicated that several large blocks of about 1000 cu yd each had failed on steeply inclined joint surfaces. Stability was reduced by extensive seepage caused by heavy rainfall. In addition, considerable overbreak had occurred, indicating excessive blasting had been used to excavate the slope. A program was developed to rock bolt potentially unstable blocks that could slide on dipping discontinuities. Some rock was scaled back to the inclined joints, and drain holes were drilled to reduce water pressures. The project was completed successfully and within reasonable economics. As a result of this success, enquiries were received regarding other mining projects. This indicated the potential demand for rock slope engineering. As a result, I took one month off to meet and discuss rock mechanics and slope stability with various people internationally. These included D. Coates in Canada, E. Hoek in England, K. John and L. Mueller in Germany, M. Rocha in Portugal, and the US Bureau of Mines in Denver, CO. Early misconceptions Based on involvement in projects during the next few years, it was concluded that there were a considerable number of misconceptions that existed among some geologists and mining engineers dealing with surface rock mechanics. Some of these included: • Water is a lubricant. This is incorrect. Water reduces the shear strength along discontinuities due to buoyancy, which reduces frictional strength. It also reduces the cohesion of clayey-type rocks. • The optimum pit slope angle in rock is 45°. The optimum slope angle for safety and economics is variable and is influenced particularly by structural geology, water pressures, mine blasting practices, and the depth and degree of weathering. • The flattest angle for slope stability is dictated by the angle of repose of broken rock, about 370. Where clayey-type rocks or clayey infill in discontinuities exists, failure can occur at much flatter angles, requiring flatter slopes or artificial stabilization. • Uniaxial and triaxial tests provide the necessary shear strength parameters to design rock slopes. Most failures in rock slopes are controlled by directional discontinuities. Therefore, the direct shear test is the correct test to evaluate strength parameters for most problems.

Jan 1, 1987

By R. C. Jr. Babcock, V. S. Znamensky

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd. in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 km. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fiber in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd., of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This chapter presents the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits are outlined. Subsequent work by other companies is mentioned, but not de- scribed in detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd. who have been involved in the project. In particular, thanks go to Ramon Farmer, N.G. Corner, and A.W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this chapter are solely that of the author and result from his involvement in the discovery of the deposits and management of the exploration program. REGIONAL SETTING Ultramafic rocks on the South Island of New Zealand are thought to be Permian in age and occur between crystaIline and metamorphic continental rocks of Precambrian through Cretaceous age in the west, are thought to have once been part of the Antarctic subcontinent, and the extensive geosynclinal graywacke deposits of the Mesozoic New Zealand geosyncline in the east. They consist of the Dun Mountain ultramafics, a 130 km long segment of ultramafic rocks located at the north end of the South Island, and the Red Mountain ul- tramafics that occur in a zone 200 km long in the south half of the South Island as shown in Fig. 1. These two belts, once contiguous, have been offset a distance of 560 km by the still active Al- pine fault, which is analogous in character and offset to the San Andreas fault of the United States. The ultramafic rocks occur within a sequence of Permotriassic volcanic and sedimentary rocks that probably formed at the eastern margin of the continental plate. The ultramafics appear to be tectonically emplaced between Permian lithologies in the Dun Mountain belt (Coleman, 1966), and at the base of or between Permian volcanics and sediments in the Red Mountain belt. The Permotriassic ultramafic volcanic sequence of the Red Mountain ultramafic belt appears to be a typical ophiolite sequence. Ultramafic rocks, mixed mafic intrusive rocks and volcanics, volcanic rocks, and volcanoclastic sediments occur in apparent superposition from east to west in the area of Red Mountain. Farther south, ultramafic rocks are associated with basaltic volcanic rocks and some sediments, and still farther south are emplaced entirely in sediments. These structural compIications of the normal ophiolite sequence have resulted from the coincidence of Permian subduction, early Mesozoic extension and sedimentation, and Cretaceous subduction along the same plate margin (Landis and Bishop, 1972). The general geology in the area of the Red

Jan 1, 1986

By W. R. Dengler

INTRODUCTION Shaft sinking represents a relatively small proportion of the activities involved in mine development. Because of this limited utilization, shaft sinking has been one of the most difficult functions to mechanize. Although shaft machines (muckers) were introduced more than 30 years ago, the first machines were low-capacity units, and machines of this type did not gain wide acceptance by the mining industry until the late 1950s. However, the increasing depth of underground mines and the es¬calating costs of labor have increased the benefits obtain¬able from high-speed shaft sinking. The result has been a growing need for high-capacity shaft machines. Most of the machines available at the present time have been developed by modifying existing equipment to increase the payload capacity and performance. AVAILABLE SHAFT MACHINES In general, shaft machines may be classified accord¬ing to the types of digging mechanisms and the mecha¬nisms of operation. The available digging mechanisms include clamshells, cactus grabs, front-end buckets, and backhoes. The mechanisms of operation can be classified as either pneumatic or hydraulic. Selection Criteria For efficient operation, the primary consideration in selecting a shaft machine is its capacity. The minimum capacity of the machine should match the capacity of the hoisting system at the ultimate depth of the shaft. In many cases, two machines may be needed to obtain a sufficient mucking capacity. The shaft dimensions and configuration often dictate the type of machine that may be utilized; for example, an overshot loader does not work well in a circular shaft that has a diameter of less than 5.5 m (18 ft). Similarly, a single Cryderman mucker is not suitable for a large-diameter shaft, nor is it applicable where very high sinking buckets are to be used. Other factors for consideration include the degree of material fragmentation, the abrasiveness of the rock, and the amount of ground water that is inter¬sected. Machine Descriptions Riddell Mucker: The Riddell mucker, illustrated in Fig. 1, was first introduced in 1948. This is one of the most common shaft machines in the medium-capacity range. The Riddell mucker consists of a hoisting and traveling mechanism that operates a clamshell suspended on cables. The early machines operated with a 0.3 m3 (10 cu ft) clamshell and had an hourly capacity of approximately 27 t (30 st). This type of shaft machine has gained wide acceptance throughout North America. Essentially, the Riddell mucker consists of standard components, such as the pneumatic tugger hoists that operate the clamshell. The carriage is suspended on rails that also serve as the blasting set, located immediately below the shaft timbers. To effectively position the clam¬shell in the shaft, the operator controls the carriage travel by means of wheels that are driven by a pneu¬matic motor. The Riddell mucker most commonly is used in rec¬tangular timbered shafts. However, some units have been installed with circular rails, allowing them to work in circular concrete-lined shafts. A popular practice with many Riddell muckers is to increase the capacity through the use of larger clamshells, often ranging up to 0.76 m3 (1.0 cu yd), in conjunction with more powerful tugger hoists. In some large rectangular shafts, two Riddell units have been used side by side to achieve a sufficient capacity. Cryderman Mucker: The Cryderman mucker, illus¬trated in Fig. 2, is another common shaft machine in the low- to medium-capacity range. Developed in the early 1950s, it also has gained wide acceptance throughout North America. Equipped with a 0.3 m3 (10 cu ft) bucket, the Cryderman mucker has an hourly capacity of approximately 23 t (25 st). The Cryderman mucker is operated entirely by means of pneumatic cylinders and a pneumatic telescopic boom. The boom is suspended from a sectional frame¬work that is usually located at one end of the shaft. The framework or headframe can be suspended from an independent hoisting system located either on the sur¬face or in the shaft. In large shafts of either rectangular

Jan 1, 1982

By S. G. Axen

Design of wells for in-situ leaching is based on individual mining operation and ore deposit requirements. Major design considerations are well flowrate, depth, fluid composition, expected well life, mine operating plan and cost. A large variety of downhole equipment, materials of construction, contract services and methods of well completion and stimulation are available. A generalized design procedure which allows the engineer to optimize well design for a particular ISL application is described.

Jan 1, 1988

By M. E. Rossi

Reconciliation of long-term, block-model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term, block-model reserves against a grade control model (a model based on blast holes or production data). In this article, this is called an Fl factor for tonnages, grade and ounces. This reconciliation should also be done by comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator, such as kriging, will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMUs to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. Therefore, the grade-tonnage predictions based on blastholes also need to be assessed - considering unplanned dilution and the errors of estimation of the grade control model. This article focuses on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer. It yields several possible minable reserves and several possible minable tonnages and grades, per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation and the planned and unplanned dilution. It also carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The estimation of recoverable reserves revolves around estimating the block distribution of metal grades from the drill hole information available, typically composites of a fixed length. Ideally, this estimation should accurately predict the ore sent to the processing facilities of an operation. Here are some definitions used in this article: ? Recoverable reserves are those where an attempt has been made to estimate the actual distribution of grades (usually by a block model) that would be found in the ground at the time of mining, relative to the mine equipment size and other operational characteristics of the mine SMU. In particular, it incorporates the effect of internal dilution for each block how the grade distribution changes in variability when comparing a composite grade distribution to the "mining unit" grade distribution. In geostatistical jargon, this is known as "change of support effect," or volume-variance effect. ? Minable reserves are those recoverable reserves defined by a mine plan. In an open-pit scenario, they would incorporate pit optimization in addition to the sequencing and scheduling of production through mine life. ? All other block model estimates from drill hole data that do not explicitly attempt to estimate or measure the volume-variance effect are called in situ. It can be argued that these models may be inappropriate tools for predicting the grade-tonnage curve of the material to be sent for processing (minable reserves). The purpose of estimating recoverable reserves can be thought of as estimating the appropriate amount of dilution that should be incorporated into the model so that it adequately predicts (long-term and on average) the grade-tonnage curve of the ore sent to the processing facilities (mean grades and ton-

Jan 1, 1999