Search Documents

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduct ion through multilayer (wall and floor of airway consist of several layers of material and rock) and two-surface (dry and wet surfaces) airway wall and airway floor with convective heat and moisture transfer between their surfaces and mine air with time dependent changes of temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for calculation of the surface temperature of any type of surface of airway wall/floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. These solutions are illustrated for the case of general harmonic course of air temperature and humidity. Balance of heat and moisture transfer between surfaces of airway wall and floor and mine air is solved by an iterative method in the partial sections of airway. The temperature and the humidity of mine air on the outlet of each partial section of airway at given time are its resolutions and they are the input data for following partial section. By this way it is possible to solve complicated dynamic changes of mine air temperature and humidity in an air way system by relatively simple mathematical apparat.

Jan 1, 1991

By J. W. III Leonard, T. E. Wilson

In addition to coalbed thickness and basic coal quality data, coal drill cores can produce design data for coal beneficiation processes. To generate design data, a coal drill core should be reduced from its original cylindrical form to a particle size distribution and composition that represents (with the possible exception of top size) a raw coal process stream. Reducing a coal core with a crushing machine rarely accomplishes this representation. This investigation employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis to characterize the core in terms of first-order and zeroth-order break- age rate constants, which are indices of the propensity of the coal to degrade during handling. To reduce composition variables and conserve difficult-to-obtain coal cores, the initial drop-shatter and dry-tumbling tests were done with synthetic cores. Then, cores from three coal beds, Illinois No. 6, Upper Freeport and Pocahontas No. 5, were tested. Comparison of a crushed drill core and a drill core prepared by drop-shatter and tumbling indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed.

Jan 1, 2000

By B. Tönjes

In the course of the last decade, the concept of sustainability has turned from a catchword into a vision - a vision to which politics and industry feel increasingly committed. In terms of the energy industry, the key criteria for sustainable development are supply security, economic efficiency and social responsibility. Coal is able to meet all these criteria if it is produced in conformity with high safety standards through the use of modern mining technology and converted into electricity with the aid of environmentally friendly methods. Among the fossil energy resources, coal will, according to the vast majority of global energy scenarios, continue to be the most important input energy in power generation for the foreseeable future. Coal is therefore today, and will in future continue to be, an important element in ensuring sustainable energy and raw material supply, worldwide, in Europe and also in Germany.

Jan 1, 2005

By L. J. Dahl, S. E. Paulson, H. L. Kuhlman

To provide basic information on the processes occurring during in situ leaching, the US Bureau of Mines developed a geologic characterization research program. This includes laboratory experiments wing leaching apparatus that can accommodate whole core samples. Whole core experiments result in a higher proportion of ore mineral contact by the leach solution than packed column experiments. They also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels of the rock. The leaching apparatus developed can be wed for either constant-pressure or constant- flow rate experiments and allows for the control of flow rate, pressure, and temperature during the experiments. Details of the experimental apparatus are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grade, AZ area.

Jan 1, 1988

By Raj K. Singhal

Three principal activities are involved in planning and developing a surface mine. These are 1) definition of economic and technical feasibility, 2) design, procurement and construction, and 3) mining and reclamation. The last is the only activity which begins in the feasibility study and continues throughout the life of a mine. It is also the activity which depends heavily on use of computers. This paper deals with a method of selecting mining software and dwells on the recent progress, made in this area. Discussed also is the status of computerized equipment management and information systems: a microprocessor based technology applied to dispatch systems, monitoring of equipment health and performance, wireless data transmission to a centralized data processing unit, and mine- wide information and reporting system. Reference has been made to upcoming developments which offer the potential- of transforming the surface mine of the year 2000 into a "manless pit". Canadian achievements in all of these areas have been highlighted at appropriate places in the text.

Jan 1, 1989

An atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) on arsenopyrite surface in solutions. AFM images show that the collectors adsorb on arsenopyrite surface in patches at pH 6. Increasing the chemical dosage will increase the adsorption density of the patches on mineral surface. The increased probe-arsenopyrite adhesion measured in PAX solutions at pH 6 is attributed to the adsorption of the patches, suggesting the hydrophobic nature of the patches, which is likely the oily dixanthogen. It is also found that arsenopyrite is reactive in water in the presence of air. At a high pH with the addition of Ca(OH)2 the adsorption of collectors on arsenopyrite is greatly retarded or depressed because the mineral surface is coated by a lot of precipitates, which is hydrophilic in nature as shown by the measured strong repulsive probe-arsenopyrite detachment force. The findings confirm that the flotation behavior of arsenopyrite in xanthate solutions is very similar to that of pyrite.

Feb 27, 2013

By D. Robert Weir

The pioneers in pressure hydrometallurgy have provided a solid foundation during the past four decades. The pressure techniques are now capable of being used to push back the frontiers in the winning of metals. Pressure hydrometallurgy has been used to meet the objectives of extracting metals; purifying metal solutions, recovering metals; and rendering waste streams acceptable for disposal to waste repositories and the environment. Some examples of each of these functions are briefly reviewed. The applicability of pressure techniques to the recovery of precious metals is discussed.

Jan 1, 1985

By Christian Jeger

After recalling the principles underlying fire-damp flow in coal and the essential part played by permeability (Darcy's law) in the intensity of flow, a few theoretical and experimental results showing the possible causes and range of variation of coal seam permeability are presented. The study of firedamp flow into gate roads and of residual gas concentrations in coals as a function of the gate road distance, shows that, in French mines, coal seams in a virgin zone have a very low permeability, but they become permeable when destressed by mine workings, in particular overlying workings. This is the case not only in the fractured zone round a mine excavation in which the gas is released, but also beyond the limit of the zone degassed by the excavation. In the floor of flat seams, upward boreholes can be used for predegassing seams that have been relaxed but not degassed, as the result of an overlying coal face. In this respect we shall describe the predrainage experiment carried out in the Marienau district of the Lorraine coalfield. Predrainage can contribute considerably to the reduction of methane emission in the ventilation of newly opened longwall faces. But to be efficient and useful predrainage should meet certain conditions.

Jan 1, 1980

By S. K. Kawatra, K. J. Shoop

An analysis of an iron-ore processing plant showed that its performance was affected by seasonal temperature variations, resulting in reduced grinding efficiency during the winter months. Laboratory and pilot plant studies were conducted to determine the cause of the observed loss of efficiency at lower temperatures. Two types of experiments were performed: drop tests and wet grinding tests. Drop testing was performed to determine the effect of brittleness and frozen pore water on the breakage characteristics of the ore. The wet grinding tests were divided into laboratory tumble tests and pilot-plant tests. The combined results of drop testing and wet grinding were used to make predictions on the performance of plant-scale autogenous grinding. From the drop tests, it was determined that dry iron ore, basalt and sandstone did not change in brittleness over the temperature range studied (-25º to 25ºC). However, when the rocks were water-saturated, the highly porous sandstone became considerably more fracture-resistant upon freezing, due to "grouting" of the pores and preexisting cracks by ice. This effect was not seen for either the iron ore or the basalt, because they were considerably less porous than the sandstone. Tumble tests on both laboratory and pilot scales showed that both the addition of fines to the test charge and a reduction in temperature caused a decrease in the amount of new fines produced. This reduced fines production was the result of increased slurry viscosity when either the fines content increased or the temperature decreased.

Jan 1, 1998

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By D. M. Kjos

Large-diameter autogenous and semiautogenous grinding mills represent the primary thrust of the expanding grinding technology. In spite of initial difficulties, large autogenous and semiautogenous mills have reached an acceptable level of technology that provides the mineral engineer with a reliable, low cost means of ore comminution. A successful milling installation begins during the design stage of the grinding mill and the plant in which it is to be installed. This is particularly true in autogenous and semiautogenous mills. Critical mill and plant design factors should be considered while the mill and installation are still only "paper." Various current liner designs will be discussed ranging from lifter bar/plate to integral types. Modes of operation such as "high-low" will be considered. Liner maintenance procedures ranging from laydown area in plant design, proper mill shutdown methods, to installation and bolt tightening complete the equation to yield optimum performance possible for any particular grinding application. The objective of this paper is to discuss trends in wear materials, designs, and operating practices, and to provide some guidelines for good practice as we move through the 1980s. We will put together concepts that relate to the designs, materials, and applications so that higher performance can be obtained by the operator for his specific application. The concepts are shown as being in series became they are dependent on each other to achieve the desired performance: designs times materials times application results in higher performance (Arnson, Parks, and Kjos, 1983).

Jan 1, 1987

By L. R. Nelson

Cyprus Pima is a medium-sized open-pit copper mine located 35 km (22 miles) south of Tucson, AZ. The ore body was discovered using geophysical prospecting methods in 1953 and was originally worked as a small underground mine followed by small open-pit operations. As mining equipment grew larger and the economic ore grade dropped, the operation grew in size, through four expansions, to the present 50 500 tpd (56 500 stpd) milling rate. The remaining stripping ratio is about 2.5 to 1. Mining equipment includes 11 electric shovels ranging in size from 6 to 15 m3 (8 to 20 cu yd) and 42 diesel-electric haulage trucks ranging in size from 89 to 223 t (100 to 250 st). Mine planning is performed at Cyprus Pima to serve several functions. The most important is to plan ahead, one year at a time, to predict the ore grade and stripping requirements on a month-by-month schedule. This yearly plan is necessary for budget preparation and is revised once each quarter to incorporate variations in actual production experienced during the preceding quarter.

Jan 1, 1979

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By Fathi Habashi

WHILE HYDROGEN SULFIDE precipitates metal sulfides from aqueous solutions, other gases such as sulfur dioxide, carbon monoxide, and hydrogen, under certain conditions, precipitate the metals directly. This can be achieved at high temperature and pressure. Such processes are of great technical importance, since metals of high purity are precipitated economically in a powder form. As a result of the availability of such powders on a large scale. processes for compacting metal sheet and other mill forms directly from the

Jan 1, 1970

By Matthew E. Fowler, Jean Habimana, Roy F. Cook

The West Side CSO Tunnel, Pump Station & Pipeline Project is currently beginning construction along the downtown waterfront of Portland, Oregon. This4.3 meter diameter, 5,500 meter-long soft ground tunnel will be driven along the westbank of the Willamette River adjacent to buildings and utilities and several major pile-supported bridges. High groundwater pressure, extended lengths of gravel to cobble-size alluvium, and the need to control ground loss and surface settlements were key considerations in the selection of slurry tunnel boring machines for the project This paper presents an overview of the numerical modeling that was performed during design to estimate the strains and additional loads in the pile-supported structures and to assess the efficiency of proposed mitigation measures.

Jan 1, 2003

By Arun Patel, Diane Hirsch, Pamela Moran

The Metropolitan Washington Airports Authority (Authority) has undertaken a tremendous expansion of Washington Dulles International Airport in Fairfax, Virginia, including upgrading passenger transportation between concourses. The first stage of this expansion envisioned a shallow cut-and-cover pedestrian tunnel between the Main Terminal and Concourse B with associated vertical circulation structures. At the beginning of the design contract, the Authority’s consulting team of Earth Tech, formerly Kaiser Engineers, and the Dr. G. Sauer Corporation compared the cost and disruption of constructing the tunnel as a cut-and-cover structure to mining the tunnel using the New Austrian Tunneling Method (NATM). Upon review, the Authority endorsed the latter method.

Jan 1, 2003

By Charles A. Maliszewski, James M. Galvin, Gerhard Urschitz

With obvious signs of deterioration, the double track, historically registered Bergen Tunnels as part of the commuter rail system in New Jersey waited for rehabilitation for a long time. Serious water in filtration not only caused operational and safety hazards for the electrified rail line but also deteriorated and structurally compromised the tunnel lining. An innovative rehabilitation program was developed to enlarge the tunnel and to provide a new waterproofing system and final lining. For the rock excavation and support New Austrian Tunneling Method (NATM) principles were utilized, while water tightness was achieved by installing a PVC membrane waterproofing system followed by a reinforced cast-in-place final lining. Experienced on-site supervision generated additional savings during construction by streamlining support elements based on geologic conditions encountered.

Jan 1, 2003

Currently the challenge that our society faces is to combine the economic activity for the continuously increasing needs of our expanding population with the necessary environmental integrity and the humanistic social concerns. In this paper, the methodologies that should be applied by the progressive mining industry in order to fall within the frame of the sustainable development are summarized. The Sappes project, an advanced gold mining project in north-eastern Greece, is presented together with the approaches adopted by Thrace Minerals S.A.

Jan 1, 2003

By Robert Seal, James J. Rytuba, Michael P. Hunerlach, Roger Ashley, Dean Enderlin

Cessation of open pit mining in 1996 at the McLaughlin hot-spring type gold deposit has resulted in the development of two pit lakes that will be managed as permanent lakes with a total storage capacity of 10,000 acre-feet. The south pit lake developed from alkaline ground water infiltration and had an initial pH of 7.2. It contained high concentrations of boron and chloride, indicating that it consisted of a mix of meteoric and evolved connate waters. Numerous carbon dioxide gas vents were present initially in the shallow south pit lake, but as the pit lake increased in depth, gas venting ceased and carbon dioxide is retained in the lower layer of the chemically stratified lake. Continued increase of dissolved carbon dioxide in the lower layer increases the potential for a limnic eruption. A chemocliie occurs at a depth of 47 m. The upper layer of the lake has lower pH, temperature, and conductivity than the lower layer. Effluent from ore and waste rock piles directed into the south pit lake has contributed to high levels of antimony, arsenic, cobalt, copper, mercury, nickel, and zinc. Iron oxyhydroxide is abundant in mine effluent that enters the pit lake and adsorption onto this phase has lowered the arsenic and antimony concentrations. The north pit lake formed primarily from winter surface runoff. The acidic water, pH 4.56, initially had high concentrations of cobalt, mercury, and nickel derived from weathering products of pyritized serpentinite and shales. Buffering by wall rocks has established a slightly alkaline pH of 7.62. The concentrations of trace metals in the north pit lake have substantially decreased due to continued dilution of the lake by surface runoff and remediation of parts of the pit walls that have been covered by backfill.

Jan 1, 2000

By S. Chander

The use of various electrochemical techniques to study mechanisms of sulfide mineral- flotation reagent interactions is briefly reviewed in this paper. Prior to such studies it is desirable to thermodynamically determine solution conditions favorable for formation of hydrophobic species deemed to be responsible for flotation. The thermodynamic equilibrium involving both the stable and metastable species can be conveniently represented by an Eh-pH diagram. Thermodynamics can also be used to predict conditions where a mineral might not float if depressants are present. Under favorable conditions of flotation there is competition between reactions leading to formation of hydrophobic species with reactions that lead to formation of hydrophilic species. Due to the sluggish nature of the reactions involving sulfide minerals, a knowledge of the kinetic behavior of the system is necessary. Electrochemical methods of investigation are wed in laboratory studies to (1) control the state of oxidation, (2) determine the type and amount of electroactive species present at the mineral surface, and (3) study kinetics of electrode processes. By combining electrochemical techniques and wetting measurements the identification of hydrophobic species that might be present at the mineral surface could be achieved. Both contact angle measurements at mineral electrodes or flotation in a cell equipped with a particulate bed electrode can be used for the wetting measurements.

Jan 1, 1987