Search Documents

By Brent W. Madsen

To assist in fulfilling the Bureau of Mines goals of maintaining adequate mineral supplies to meet national economic and strategic needs, and to minimize the environmental impacts associated with mineral-processing operations, a leaching-solvent extraction-electrowinning technique was compared with a leaching-cementation technique for processing low-grade copper ores. Large-scale laboratory column leaching tests (6 to 7 tonnes) were conducted on minus 37-cm chalcocitic ore using ferric sulfate leach solutions at 25° C. Two columns contained 11 percent minus 1.27-cm fines, and two columns contained 32 percent minus 1.27-cm fines. After 416 days of leaching ore samples containing 11 percent minus 1.27-cm fines, copper extraction was 48 and 51 percent for the leach-cementation and leach-solvent extraction-electrowinning procedures, respectively. When leaching ore samples containing 32 percent minus 1.27-cm fines, the leaching-solvent extraction-electrowinning technique extracted 60 percent of the copper after 568 days, whereas the leaching-cementation technique extracted only 48 percent of the copper. In the latter test, leach solution ponded on the ore, which reflected a decrease in ore column permeability. The decreased permeability was attributed to the generation of excessive amounts of iron salts during cementation; the salts precipitated on the fine ore particles and in the interstices, thus plugging the column. This decrease also lowered the available oxygen, resulting in poor aerobic bacterial activity which slowed the oxidation rate of ferrous ions to ferric ions. Sulfuric acid required to maintain a leachant pH of 2 was nearly halved when copper was recovered by solvent extraction and electrowinning rather than by cementation.

Jan 1, 1979

By B. Schimm

Improve the mines productivity by simplifying the mining process, for these tasks the Wirtgen Surface Miner offers an attractive alternative. Surface Miners cut, crush and load material in one operation with only one machine. The cutting depth is controlled exactly.

Jan 1, 1997

By R. E. Williams

University of Idaho scientists research under U.S. Bureau of Mines Cooperative Agreement C0278001 constitutes a complex hydrogeological, hydrochemical and metallurgical mine waste management project at an existing Superfund site. Technologies that may prove useful for the extraction of dissolved metals from acid mine water and solid wastes include lixiviation and biosorption. Acid mine water is the major, long-term problem in the valley. We are attempting to delineate the major sources of ground water recharge which feed the acid mine drainage and their hydraulic properties. Grouting of recharge areas may facilitate minimizing the production of acid mine drainage if recharge pathways can be identified.

Jan 1, 1990

By H. P. Rosenof

The G2 real-time expert system, a commercial product since 1988, is widely deployed in process, manufacturing and other industries. A number of innovative applications are installed or under development in the mining and metallurgical industries. These include: ? A chemical reagent control system for a mineral concentrator, at a mining company; ? A supervisory control system for a product dryer, at a surface coal mine ? A training system for equipment operators, at a steel mill; ? A scheduling system for furnaces at a hot rolling mill; ? A simulation system for mining operations; ? Several graduate-level research projects in materials handling at a university Realized and projected benefits will be discussed. In addition certain applications installed or under development in other industries will be proposed as applicable in mining and metallurgy. For example, applications for the management of vehicular traffic may find use in mining and shipping.

Jan 1, 1992

By S. Tafazoli, D. Cooper, I. Bell, S. Nouranian, B. Sameti, M. Ramezani

"Image-based rock fragmentation sensing in mines and quarries includes an important rock boundary delineation step, commonly referred to as rock segmentation. This paper presents an artificial intelligence-based solution to this challenge. The proposed technique encodes prior knowledge of previously analyzed images into mathematical/statistical models. Human-labeled images are used as inputs to train neural networks through an optimization process. The networks can then be used in real time for rock delineation. To build the models, special deep artificial neural networks are used as a pixel classifier. The proposed classifier labels each pixel (edge, rock or fine) by analyzing a plurality of pixels within the image. Advances in machine learning allow the network to contain many parameters. The increased number of parameters is a strong factor in the classifier’s ability to correctly classify each pixel. Deep learning-based segmentation, combined with 3D imaging followed by post processing, provides a unified fragmentation sensing solution. Results from automatic segmentation are compared to human labeled segmentation using the percentage passing curves for 64 rock images. INTRODUCTION Mines and quarries can see significant productivity and performance benefits by controlling material sizes (McKee, Chitmobo, & Morrell, 1995; Sellers & Gumede, 2012). During the past decade, image-based fragmentation analysis has been applied to estimate rock size distributions in order to optimize procedures in mines and quarries. Using a roving camera and operator assisted analysis Maerz, Franklin, and Coursen (1987) measured the size distribution of the blasted rock and eliminated the need for manual sieve analysis. Since then, many others have introduced automated and manual methods for fragmentation analysis and improved upon existing approaches (Girdner, Kemeny, Srikant, & McGill, 1996; Smith & Kemeny, 1993; Palangio, Palangio, & Maerz, 2005; Tafazoli & Ziraknejad, 2009; Raina, 2013). In image-based fragmentation, rock boundaries are identified in the image, and an image scaling is applied to transform rock pixel sizes into real world dimensions. Usually geometric references, such as regularly shaped objects (discs and basketballs) (Siddigui, Ali Shah, & Behan, 2009), or the known size of an excavator bucket (Zeng, Chow, Baumann, & Tafazoli, 2012), are used to determine the proper scaling factor. In recent years, 3D imaging and sensing have also been incorporated to improve rock delineation. Specific methods include using camera-laser combinations and stereo imaging to measure rock fragmentation on conveyor belts (Noy, 2013; Thurley, 2013; Dislaire, Illing, Laurent, & Pirard, 2013) as well as portable fragmentation analysis devices with 3D imaging sensors (Sameti, et al., 2014)."

Jan 1, 2018

By T. A. Toney

A sampling program was conducted in 2008 to determine the run of mine characteristics of 5 coal seams. The sampling program included size analyses and float sink determinations. The samples were analyzed for ash and mercury concentrations for each size and gravity fraction. This paper will report on the sampling program, the analytical results, and the correlations determined in the data set investigated.

Jan 1, 2010

By P. S. Hettinger

Land Application Discharge (LAD) is a useful method of disposing of waste water from mining operations and in certain climatic regimes, stormwater runoff. LAD systems function under the premise that metals, salts and nutrients in water are dispersed over a large area and are effectively assimilated into the soil profile. Depending on the soil structure, migration or mobilization of dissolved metals through the soil profile can be Substantially reduced. Land application of treated effluent from sewage lagoons or waste water plants was probably the first general use of land applied water. LAD has gained popularity with the mining industry as a means of disposing of waste water and process water. In addition, large volumes of snow meltwater and stormwater are often placed in storage in Montana during spring, and Land Application Discharge has shown to be an effective method for disposing of stormwater during the dry, summer season. LAD can also provide an alternative to recycling or treating waste water at on-site waste water treatment plant&. Application of stormwater or process water can result in little or no change to the background concentrations of metals in baseline water quality samples. One cautionary note about LAD: high salt concentrations and pH values are associated with process water from heap-leach facilities and are known to cause burning of local vegetation. Some pre-treatment of process water may be necessary to prevent such environmental problems.

Jan 1, 1994

By K. S. E. Forssberg, J. A. Jirestig

Laboratory investigations on the possibility of using magnetic separation for the recovery of sulfide minerals have been reported. A survey of several sulfide ores and flotation concentrates indicated that, in most cases, magnetic separation is not a suitable primary beneficiation method. However, encouraging results have been obtained in concentrate purification. At the Boliden complex sulfide ore concentrator in Garpenberg, Sweden, an Allis-SALA Mark III carousel High Gradient Magnetic Separator (HGMS) is used with a small flotation circuit to recover sphalerite lost to the galena concentrate during lead flotation. After four years of refining the HGMS process, there has been an increase in zinc recovery and an enhancement in the quality of the lead concentrate.

Jan 1, 1994

By R. Day

Nahcolite is a naturally occurring sodium bicarbonate mineral found principally in the Piceance Creek Basin of northwest Colorado. An 8-m thick nahcolite bed, 610 m below the surface, is the target of this first commercial nahcolite mine. A chamber and pillar mining system is developed by solution mining parallel 8-m tall by 18-m wide by 450-m cavities initiated along horizontally drilled holes. Hot water leaching, cooling crystallization and flash drying is the process. The sodium bicarbonate product is consumed by the baking, animal feed, industrial and acid rain abatement markets. A project overview, emphasizing the combination of horizontal drilling and solution mining technologies, will be presented.

Jan 1, 1994

By E. A. Córdova

Current methods for scratching a piece of rock to obtain or check the characteristics of its component material can sometimes be expensive and time consuming. Scratching a rock core requires an object with a point that it is capable of sliding along the surface of the rock while recording the response from the rock due to the sliding. With the idea of providing a cost efficient solution for a scratch device, a new generation turntable arm, composed of a cartridge with a diamond stylus and a USB output connection to the computer, was used to record the vibrations from the sliding of the stylus along a rock core surface. The output sound from the stylus was captured with the computer as an audio input signal. The raw sound data was recorded in a standard waveform audio format (wav) file, and post-processed using sound spectrum analyzer software (Spectra-Lab) to capture numerical data such as frequency, amplitude, and noise from the file. The results for frequency, amplitude, and noise were compared and plotted against the scanned surface of the rock core in the search for correlations that might represent specific characteristics of the surface being scratched.

Jan 1, 2010

Dravo Corporation was founded in 1891 and has long been recognized as a major domestic engineering and construction firm headquartered in Pittsburgh. In 1977, Dravo had revenue of $852.2 million with international business activities contributing $248 million; quite a different picture than envisioned at the turn of the century. Engineering and construction activities still dominate Dravo's most recent history and will do so for the immediate future. However, fluctuations in capital spending by large industrial sectors of our economy during the late sixties were affecting Dravo's planning for continued growth along its traditional lines of business. Diversification was a possible solution to smooth out the upward trend in corporate earnings. One large result of these continuing efforts was the formation of Dravo Lime Company, a vertically integrated, proprietary chemical supplier for the air pollution control market. Briefly retracing the seventies, the passage of the Federal "Clean Air Act" in 1970 supplied the impetus for Dravo Lime Company. This law promulgated limits on the emissions of sulfur dioxide (SO2) from large stationary sources that would affect local air quality. The major industry that felt the brunt of this regulation was the electric utility industry, especially those generating electricity with coal-fired boilers. The law hastened the development of a new industry, flue gas desulfurization (FGD), and is composed of three major segments: (1) the electric utility, (2) the FGD equipment suppliers (the scrubbing modules), and (3) the scrubbing chemical suppliers. Dravo's experience suggested the equipment end of the business but market analysis indicated that our long range corporate goals could be better attained by investigating the chemical processes involved in the removal of the SO, gas. The result being Dravo Lime Company. This paper will briefly describe the Thiosorbic lime scrubbing process and review our innovative mine and calcining facility.

Jan 1, 1978

By B. R. Waples

Sometimes a project is born easy, sometimes a project has a hard time being born. Probably every project can say we had tremendous problems to overcome and they would all be right. This project had all things happen to it. Born easy, a hard time after being born, there were tremendous problems to overcome but here it is, a major copper project, a major operation, and a new source of copper for Mexico and the world market. La caridad is an ore body located in the state of Sonora in northwestern Mexico. It is at an elevation of 1,200 meters above sea level and the nearest major city is Hermosillo, the capital city of Sonora. Hermosillo is located approximately 270 kms (about 168 miles) to the southwest of la caridad. North of la caridad, 130 kms (about 81 miles), is the U.S. border town of Douglas, Arizona, which has a sister city on the Mexican side of the border -Agua Prieta.

Jan 1, 1979

By M. J. Virnig, G. A. Kordosky

Throughout time, the mining industry has been very successful in meeting the world's requirements for metals and materials while meeting the challenges of decreasing ore grades and increased emphasis on protection of the environment. This success has been due to the development and implementation of new technologies. A clear example of such a development over the past 25 years is the increasing use of leaching/solvent extraction/electrowinning for the recovery of copper from oxide and sulfide ores. The key to the successful introduction of this technology was the discovery and development of the hydroxyoxime liquid ion exchange reagents by General Mills Chemicals (now Henkel Corporation). An important role was also played by the close working relationships between General Mills Chemicals and Ranchers Exploration which resulted in startup of the first plant in 1968 and between General Mills Chemicals and Bagdad Copper which resulted in the startup of the second copper SX-EW plant in August of 1970. Following on the heels of the hydroxyoxime development came the commercialization of other new chelating reagents based on different chemical functionalities, i.e., beta-diketones, alkylated 8- hydroxyquinolines and sulfonamidoquinolines. This initial spurt of activity was then followed by a slowing of development in terms of new reagent functionalities. Activity has continued in terms of further optimization/improvement of existing reagent functionalities but the commercialization of new reagent functionalities has slackened. This observation reflects the fact that the development of new reagent functionalities for metal recovery has become increasingly more expensive such that the right combination of price and sales volume must exist in order to justify the investment required to bring a new reagent to the market place. Given the dependence of the mining industry on innovation to meet the needs of the future, one can ask how these new developments, particularly in new reagents, will occur. To arrive at an estimate of the costs involved in commercializing a new metal extractant functionality, particularly a chelating type functionality, a case study of the development of LIX ®* 34

Jan 1, 1994

By Cuthbert Musingwini, Adeodatus S. Nhleko, Mahlomola I. Mabala

Optimization of a three-dimensional (3D) underground stope layout is complex given the number of variables and constraints to consider, such as the stope size. Determination of the appropriate stope size in stope layout optimization problems is a complex process that must consider several factors including placement of infrastructure and development, production scheduling, and equipment selection. An inappropriate stope layout can result in unrealistic expectations for a production schedule, consequently negatively affecting the derived economic value. Therefore, this paper used a dual interchange algorithm (DIA) to evaluate the effect of stope size on the stope layout economic value (SLEV) for a synthetic Platreef mineral deposit planned for extraction using sublevel open-stoping. The results showed that generally as the stope size increases, the SLEV decreases. This aligns with practical mining because larger stope sizes have a higher chance of incurring more dilution which reduces economic value, while smaller stope sizes enable more flexible extraction where unprofitable blocks can be left unmined as waste, thus increasing the derived SLEV.

Jun 25, 2023

By Frank M. Howell

Creede, one of the younger major mining camps in Colorado, grew spectacularly to a town of eight or ten thousand people in the early 1890's following discovery of rich ore in the Amethyst and Last Chance mines. Gross metal production in gold, silver, lead, copper and zinc rose to a maximum of four million dollars a year in 1893. Annual production dropped to much lower figures and ranged between one hundred and five hundred thousand dollars per year during the period from 1914 to 1940. Production reached a gross of eight hundred thousand to one million dollars per year by the mid-1950's. In the years 1953 to 1957, Steven and Ratté conducted geologic investigations which were carried on as part of a cooperative program of the U. S. Geological Survey and the Colorado Metal Mining Fund Board. In a preliminary report on the Creede District, Steven and Ratté suggested that the Bulldog Mountain Fault Zone appeared to be a favorable structure to prospect. On the basis of that recommendation, augmented by independent work done by Manning W. Cox, the property was acquired, transferred to Bulldog Mountain, Inc. and financed by an O. M. E. loan. Late in 1963 Homestake Mining Company, under a Lease and Option Agreement, backed the venture by furnishing additional funds plus management.

Jan 1, 1969

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increasing usage for acid mine drainage mitigation as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1998

By Ivano Andreis, Georgios Kalamaras, Mario Liti, Sebastiano Pelizza, Filippo Avesani

"THE SS640 AGRIGENTO-CALTANISSETTA PROJECT The Caltanissetta tunnel is part of the works for the construction of the second 28km-long maxi section of the SS 640 motorway of Porto Empedocle, from km 44 to the junction of Imera in Sicilian hinterland. Amongst other major infrastructure works, the €740 million ANAS (Italian national roads and highway administration agency) project consists of four twin tube tunnels three of which are being excavated by conventional means. The longest tunnel, underpasses the Caltanissetta city and has a length of 3.9km under a maximum overburden of 120m. The JV consisting of CMC of Ravenna and TECNIS SpA won the design & built tender in 2010. Construction started in early spring 2012 following the approval of detailed design and later on the approval of design for construction. THE CALTANISSETTA TUNNEL The Design Phase Tender design and detailed design foresaw the construction of 13.4m excavation diameter tunnels that were to be enlarged in a second phase to create, every 600m, 50m-long tunnel sections for emergency parking. During the design for construction project phase the JV proposed to replace the 13.4m tunnel with a 15.08 excavation diameter that incorporated apart from the two 3.75m wide lanes a 3.25m wide continuous emergency lane. This significant tunnel section modification was associated with better road safety conditions, simpler and safer construction procedures, better statics for the tunnel section while in terms of overall cost the solutions were equivalent.Geologic context The tunnel is located in the middle of the geologically known Caltanissetta basin that is intersected by various tectonic structures. The geologic context for the tunnel scale, was defined in collaboration with the University of Catania in early project phases. For almost its entire length the tunnel is excavated in the Terravecchia formation that represents the lower part of the stratigraphic sequence that was formed in the Tortoniano period of Miocene. The quite complex geological model is also characterized by the presence of the so-called Trubi formation that consists of clay and marl clay. Almost 90% of the tunnel traverses formations that are quite similar in terms of excavation behavior. Exception to this are thrust zones and a calcareous stretch of the alignment. This last segment has a length of 200m and was identified since the very beginning as a tunneling challenge due to the combination of very poor geotechnical properties and an important water load."

Jan 1, 2016

By K J. Kidd

There is general understanding of hoisting systems throughout the mining industry. However, the relative importance of the various parameters influencing hoist selection and utilization is not completely understood. In order to determine if these parameters can be identified and prioritized, data covering 613 hoist installations were compiled. The 613 installations represent hoisting systems in 30 countries on six continents. This study compares data to historical trends, correlates design parameters in an attempt to identify underlying selection criteria, and comments on the apparent trends in recent developments in hoist design.

Jan 1, 1998

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015