Search Documents

By Ping Zhang, Xu Ma

Perturbations from mining operations significantly affect the stability of rock masses, especially with the increase in mining depths. This study uses the discrete element method (DEM) to investigate shear slip failure along discontinuities in an underground mine, aiming to quantify seismic moment and seismic energy to better understand seismic hazards.

May 1, 2023

By FELIPE SÁNCHEZ, PHILIPP HARTLIEB

Innovation plays a critical role in the mining industry not only as a tool to improve the efficiency of its processes and to reduce costs but also to meet the increasing social and environmental concerns among communities and authorities. Technological progress has also been crucial to allow the exploitation of new deposits in more complex scenarios, such as lower ore grades, extreme weather conditions, deeper deposits, harder rock mass and high-stress environments.  

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By Matthew Geary, Stephen J. Marino, Jordan A. Schreiner

"INTRODUCTION Project Overview The Southeast Collector (SeC) is a new 15km long 3.0m internal diameter wastewater tunnel designed by Hatch Mott MacDonald (HMM) that twins the existing 2.6m diameter York-Durham Sewage System (YDSS) tunnel. Both sewage tunnels are located north of the City of Toronto in Ontario, Canada. The SeC provides much needed conveyance capacity for the rapidly growing York Region population, supporting development until 2036 and increasing sewage system security (Hatch Mott MacDonald and AECOM 2011). Construction of the SeC will also permit flows of the twinned section of the YDSS to be bypassed in order to clean, inspect and carry out any essential maintenance within the YDSS tunnel. Although owned and operated by York Region, the SeC spans two regional municipalities beginning upstream from the intersection of Ninth Line and Rouge Bank Drive in the City of Markham in York Region to the downstream Finch Avenue and Valley Farm Road intersection in the City of Pickering in Durham Region. See Figure 1 for the SeC and YDSS alignment. The project includes 19 shafts and chambers with depths ranging from 8 to 48m in addition to seven facilities supporting the operation and maintenance of the sewer. The construction contract was awarded to Strabag Inc. in July 2011 for $291M CAD. Construction Management services were provided by a joint venture team of Hatch Mott MacDonald and AECOM. Existing York-Durham Sewage System The YDSS tunnel was completed in 1979 and was constructed using an open shielded TBM with ribs and lagging temporary support, followed by installation of a 380mm thick unreinforced cast-in-place (CIP) concrete final lining. The YDSS sewer system has numerous connections that accumulate flows from various urban areas within York Region. The section of the YDSS twinned by the SeC flows under gravity conditions and had been putting a strain on the municipality’s potential for population and development growth having reached its maximum capacity of 420 ML/d. According to the York Region’s Water and Wastewater Master Plan, the existing YDSS would not have been able to handle wet weather flows past 2016 (Genivar and XCG Consultants 2009). The dependability of this section of the YDSS is also of concern because it is the main and critical connection between the sewer systems upstream and the downstream Duffin Creek Water Pollution Control Plant (WPCP)."

Jan 1, 2016

By D. McBride

Representative samples are required from process streams in order to accurately measure chemical and physical characteristics. This information can then be used by process operators and metallurgists to evaluate the process and effect control actions for the operation. The capture and presentation of representative samples can be critical to measuring values, such as elemental analysis and particle size, with on-line or near-stream analyzers. A comprehensive multi-physics model has been developed and used to better understand the effects of slurry flow and particle segregation under certain operating parameters. An algebraic slip model coupled with a free surface algorithm is used to track motion and position of particles and phases within a specified geometry.

Jan 1, 2009

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4)-air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) measured thermal-runaway pressures of lithium iron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 4260 psia (294 bar) of pressure during a thermal runaway, far exceeding minimum pressure containment specifications for conventional explosion-proof enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce thermal-runaway pressures to levels below that expected for CH4-air ignitions. Measured thermal-runaway temperatures were below the minimum autoignition temperature of CH4-air.

By J. B. Hadaway

The current limit to power transmission for grinding mills through one mill pinion is approximately 7,500kW. Above this power rating either twin pinion arrangements or Gearless drives are required. The SMTP concept was developed to overcome this limitation by using two pinions with a single large drive motor. The SMTP mill drive offers major advantages in capital cost and greatly simplifies plant layouts, while using an innovative adaptation of industry-proven single helical gearing. Through the use of a single motor, provision of variable speed drive is greatly simplified. The SMTP can also be used for significant power upgrades on existing mills.

Jan 1, 2001

By Mirza Muhammad Zaid, Nana A. Amoah, Ping Chang, Guang Xu, Ashish R. Kumar

The key takeaway of this study is the significant improvement in dust protection for roof bolter operators in underground coal mines. The optimized canopy air curtain (CAC), with a redesigned two-level manifold system, provides uniform airflow distribution that effectively reduces dust exposure. By enhancing the protection of operators from harmful respirable coal and silica dust, this technology can reduce the risk of diseases such as coal workers’ pneumoconiosis (CWP) and silicosis. The application of this optimized CAC design in real-life coal mining operations can dramatically improve worker health and safety by minimizing dust-related exposure, ensuring compliance with industry regulations and prolonging the lifespan of mining equipment by reducing dust accumulation.

Dec 1, 2024

By W. S. Weldon, R. M. G. Machunter

The use of spiral separators for the beneficiation of fine coal typically in the size range - 2+0.lmm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimise metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Feb 24, 1997

By Carl G. Bock

INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has let a contract for the excavation of three rock stations, spaced about 3550' (1082m) apart, beneath Connecticut Avenue in Washington, D.C. Two previous rock stations have been completed, one of which had a crown pilot tunnel excavated to explore geologic conditions that would be encountered during the station excavation. This pilot tunnel was primarily for inspection by bidders and design was based on core hole information. The other rock station had no pilot tunnel and was also designed on the basis of core hole information. The three rock station areas, which are the subject of this paper, have been explored by crown pilot tunnels and an as-built report, with geologic maps and sections, has been prepared, for use by the design engineer as the basis of design for support of the structures. The geotechnical report describes the geologic structure in detail and relates it to excavation and support of the three crown pilot tunnels and the running tunnels which will be enlarged to create the 58'W x 44'H x 700'(+)L (17.6m x 13.3m x 212m +) stations. The information was complete enough to permit the design engineer to visualize the geologic structure and compute loads for the various types of rock conditions. It was therefore possible to determine the size and spacing of the steel sets for the several different conditions of rock structure encountered in the pilot tunnels.

Jan 1, 1976

By A. K. Mukherjee

The roles of pulsating mechanisms such as the amplitude and frequency of the jig cycle are well established in jigging. Also well established are the roles of the size ratio and the volume fraction of the feed. In iron ore beneficiation plants, these process parameters are optimized to achieve the highest efficiency. However, the role of one of the more important feed characteristics, the liberation characteristic of the feed, has not been studied in detail. Evaluation of the liberation characteristics is difficult because the required washability test is not viable for iron ore feed. In this paper, a new method is proposed in which the liberation characteristics are measured through a separation efficiency value. In the new evaluation method, jigging parameters such as amplitude and frequency of the jig cycle are optimized from the fundamental understanding of the process dynamics and feed characteristics such as size distribution. Then, feeds with different liberation characteristics are tested to evaluate the liberation characteristics of feed in jigging.

Jan 1, 2008

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By William R. Yernberg

The current state of the copper industry was the topic of discussion at the Copper 99 — Cobre 99conference held Oct. 10 to 13, 1999, in Phoenix, AZ. More than 700 copper-industry engineers, executives, consultants, academics, vendors and other interested parties attended. This successful and well-organized conference was the fourth in a series of international conferences devoted to the mineral processing and extractive metallurgy of copper. The 1999 meeting marked the first time that the conference was held in the United States. The meeting was co-organized by the Minerals, Metals and Materials Society (TMS); the Chilean Institute of Mining Engineers (IIMCH) and the Metallurgical Society of the Canadian Institute of Mining, Metallurgy & Petroleum(CIM). The meeting was also sponsored by The Society for Mining, Metallurgy and Exploration Inc.

Jan 1, 2000

Atlas Copco Wagner launched its ST1010 Scooptram load haul dumper. The ST1010 replaces the company’s Wagner ST-1000 Scooptram. The improvements to the Wagner ST1010 include increased reliability, ease of maintenance and driver comfort or ergonomics. The ST1010 has been redesigned and has added several new features and options not offered in the earlier model. These include anew boom design with side stops. Heavy reinforcements to the bogie offer better protection against the harsh working conditions in underground mining and tunneling. An auto lube system has also been added as has paint-on grip tread to reduce slips and falls during maintenance checks or repair work. Other features include a heavy-duty, auxiliary-fan motor, an isolated transverter, remote diagnostic pressure taps, a bolt-on battery box, raised air-intake, improved fuel-filter access for easier maintenance, larger wear-bars around the engine tub, and smaller, higher output batteries

Jan 1, 2000

By Maurice Deul

For the first half of the 21st century, the United States will rely on the same mix of fuels it has for the past 50 years. Petroleum for the United States will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in stress on the gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging “piggy-back” trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By C. J. Bise, D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard- recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Feb 24, 1997

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By Raymond W. Henn

The 30th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 22-26, 2009. The field demonstration portion of the course was conducted June 25, at Hayward Baker, Inc.?s yard in Broomfield, CO. The full-scale field demonstration annually presents many different types of drilling equipment being operated as well as various grouting methods being performed under different field conditions. As part of the field demonstration, the class is shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and measured conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results. The goal of the sand column demonstration is to show the students the effect of the water cement ratio and the use of admixture as well as the fineness of the cement, portland versus ultrafine, used has on the engineering properties of the grout and the grout?s vertical permeation through the sand. Test results for the demonstrations conducted in 1999 and for two separate demonstrations, one at the grout course and one at Geo Denver, conducted in 2000 were published in the 2001 proceedings of the Rapid Excavation and Tunneling Conference (RETC) (Henn et al. 2001). The test results for the 2002 and the 2003 demonstrations were published in the 2005 proceeding of the RETC (Henn et al. 2005).

Jan 1, 2009

By H. Kinilakodi

In 2008, the authors developed a methodology for identifying underground coal mines at high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later, using a sample of 103 mines with 2008 and 2009 data, injury measures and U.S. Mine Safety and Health Administration (MSHA) citation data were combined into a safe performance index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large and medium-sized mines. Mining Engineering, 2011, Vol. 63, No. 10, pp. 73-77. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011