Search Documents

By N. P. Titkov

This paper presents the results of laboratory and pilot plant investigations for the development of efficient methods of beneficiating hematite ores from the Krivoi Rog, Kursk Magnetic Anomoly, Olenogorsk, and other localities. The tests included gravity, magnetic (in a high intensity field), flota¬tion, and magnetizing roasting methods. It was possible to develop efficient beneficiation methods depending on the mineral composition of the ore and degree of dissemination of ore and gangue minerals. The paper shows the relationship between the iron silicate and quartz content of the ore and the technologic indices of the various beneficiation methods. Some of the conclusions based on these investigations and the technical and economic computations related to the cost of one ton of pig iron produced from concentrates obtained by the various beneficiation methods are: 1. If the hematite ore is not disseminated uniformly, it is expedient to use a combined gravity and flotation process. Ore particles up to 50 am. in size are beneficiated by gravity (heavy suspension, jigging, and others) and yield a lump concentrate. The middlings from this process are recrushed and floated; 2. Finely disseminated hematite ores, containing small quantities (less than 5 percent) of iron silicates, are most effectively beneficiated by flotation. Anionic (sulphate soap, tall oil emulsion with various foam depressors) as well as cationic collectors may be used. Depending on the mineral and chemical composition of the ore, it is possible to obtain concentrates containing up to 65 percent iron with an extraction up to 94 percent; 3. Finely disseminated, mixed hematite-magnetite ores may be beneficiated by flotation or a magnetic separation-flotation process; 4. Finely disseminated hematite ores, containing large quantities of iron silicates and earthy hematite ores are most efficiently beneficiated by the magnetizing roasting method. This method will yield concentrates containing up to 68 percent iron with extractions up to 90 percent. Although beneficiation by the magnetizing roasting process is costly, it will nonetheless, when employed on this type of ore, yield the least expensive pig iron.

Jan 1, 1960

By J. L. Brinkman

"One of the most common emissions from detonating explosives are nitrogen oxides (NOx), which are potentially deadly if inhaled. Lab studies estimate emission quantities, though great variation is shown based on site-specific conditions, and lab tests may not fully represent field results. Field VALUES (have not been measured due to the vast area affected. OSMRE recently promised to release a ruling regarding surface mine NOx production. Once the ruling is implemented, it may eventually be necessary to monitor site-specific NOx production from blasting. A small unmanned aerial vehicle system (sUAS) is able to carry a NOx gas monitor, rapidly travel to the blast location, and to follow resulting clouds of dust and emission gasses. This project will perform laboratory tests to expand on current estimations, determine an optimal method for collecting data, and evaluate the ability for this unique application of sUAS to assist in health risk assessment for mine employees and nearby communities. Additionally, large initial NOx concentrations do not necessarily correlate to unsafe conditions, and this project will be ground breaking in observance of surface blasting emission dispersion. The project is still in early phases at the time of submission for this paper (Nov 1, 2017). Therefore, this paper focuses primarily on summarizing background research related to the project and a description of the project plan. INTRODUCTION Nitrogen oxide gases (NOx) are common emission by products of surface mine blasting. These gases can potentially cause risk to human health and safety, both for mine workers and communities near the blast site. However, these emission quantities are largely unmeasured and no attempts have been made to relate these VALUES (to human health risk. The primary objectives of this project are to determine actual quantities of emission gases produced during surface blasting, to evaluate immediate and long-term risks to nearby people, communities, and ecosystems, to develop a system for mine employees to easily monitor emission and risk levels, and then provide guidelines for mitigating health risks based on a location’s emission results. BACKGROUND Current research regarding health risk produced by surface mine blasting NOx emissions is extremely lacking. Estimations have been made based on laboratory research, though these same test results show wide ranges of possible gas quantities produced based on site-specific conditions. Even if these estimations are accurate, no method has been created to relate gas quantity produced to human exposure concentrations. To further understand this field, background research was studied pertaining to blasting emission gas formation, laboratory and field measurements, harmful effects of blasting emission gases, and relevant government regulations. Background on Blasting Emission Gases"

Jan 1, 2018

By A. K. Sheik

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine opening stability. Laboratory test data, borehole measurements and geological mapping assisted in constructing a coupled finite element model of the rock mass. The model was used to make quantitative estimates of: 1) rock stress, strain and displacement changes, and 2) water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. Stability of crown pillars between stopes was of particular interest. The relatively low effective stress and high rock mass strength showed that water pressure changes were of no great consequence in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific input data.

Jan 1, 1999

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By M. L. Smith

SAG mill throughput is often a bottleneck in increasing metal productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility which is also relevant to the rock fragmentation that is achieved by blasting. The relation between the size distribution and fragility of the feed and of the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1993

By Tedd B. Bodimer

Why complicate an already complex machine such as a continuous miner by adding roof drills? Immediate permanent roof support is an immediate thought of the mining engineer just as elimination of frequent time-consuming places changes is a thought of the methods engineer. The realization of those two objectives has the potential for improved safety with increased production is the thought of the general manager. Miner-Bolters Used a Generation Ago These are not new thoughts as the 1CM continous miner equipped with two integral roof drills was introduced twenty-five years ago. Approximately two hundred of these machines were sold in the next five years for use in medium and high seam operations. The 1CM miner chassis that remained stationary in the center of an entry or room while the ripper bar was swung and sumped hydraulically provided an ideal platform for mounting two roof drills that could be operated during the continuous miner's production cycle. Two roof bolts could normally be installed in less time than required for the mining cycle. A typical roof drill unit is shown in Figure I.

Jan 1, 1981

By B. J. Sauer

Misapplication of AC induction motors for mine crusher and mill applications has long been a frustration for both the driven equipment supplier and the mine operator. Proper selection of AC induction motors is critical to providing efficient production. This paper focuses on the selection of AC induction motors for gyratory crusher, cone crusher, and grinding mill applications. The criteria for motor selection includes: proper enclosure, driven equipment torque requirements, bearing life, temperature rise, starting requirements, ambient temperature, altitude and accessory requirements.

Jan 1, 1999

By Harold L. Lovell

The areas of application, the limitations imposed by water chemistry as well as the advantages and disadvantages in the use of limestone for the treatment of coal mine drainage have recently been described by the authors (1),(2), (3). The process has been demonstrated in continuous, full-scale operation to yield a treated water meeting specifications established by the Pennsylvania Sanitary Water Board and containing excess alkalinity. Their final pH levels are usually less than seven, a condition which avoids consumption of excess neutralization reagents, but which occurs with lime-based processes and results from unwanted side reactions. Operating experience has been cited by Calhoun (4) using ferric waters while others (5), (6), (7), (8), (11), have reported on related research efforts. Despite the advantages including ?the relative simplicity, and minimal costs of the process, there have been very limited industrial applications of mine drainage neutralization with limestone. Although any treatment of these waters may be considered as a temporary control measure (9), the lack of feasible, immediate alternatives, the extensive magnitude. of the waters and the high cost of treatment requires that optimum processes should be utilized and that operating experience in their use be developed as is feasible. This paper will review treatment experience with a ferrous water of moderate pollution loading .

Jan 1, 1972

By W. D. Keller

Scan electron micrographs, SEM's, will be shown of representative refractory clays from Missouri deposits, with counterparts from other localities. The story is in the pictures, ("1000 words in each picture"), but clay types include the following. Plastic, semi-plastic, and semi-flint "fire clays" of Missouri have textures which appear to retain certain relic texture of ball clay. Flint clay is composed of tightly interlocking packets, sheaves, and books of kaolinite. Diaspore and boehmite mineral textures characterize those "clays". Surface-boulder diaspore shows very pronounced recrystallization and crystal enlargement from original, unexposed first-grade diaspore.

Jan 1, 1977

By C. H. Sheerin

Remotely located in the jungle near mount Puncak Jaya [16,500 ft (5,030 my), Irian Jaya, Indonesia rests Freeport's Indonesian copper mining operation. Shortly after start up of Freeport's copper concentrator in 1972, lower than estimated throughput was experienced within the crushing circuit. Within one year, Freeport had successfully engineered a solution, and was operating a 5,500 dmtpd wet screening circuit. Today, after 19 years of successful wet screening expansion and operation, the concentrator processes 57,000 dmtpd.

Jan 1, 1993

By Frank Florez

INTRODUCTION The Magma mine, located at Superior, AZ, some 100 km (60 miles) east of Phoenix, was discovered in 1875, and was originally mined for silver. The property was acquired by W. B. Thompson who formed the Magma Copper Co. in 1910. Prior to 1965, square-set mining and cut-and-fill methods were used to mine steeply dipping veins at Magma. Ore was moved to the chute by gravity in the square-set stopes and by slusher in the cut-and-fill stopes. The stopes were gobbed with waste from the surface and development headings in the mine. The original square-set method of mining was modi¬fied in order to extract replacement ore bodies in limestones that dipped at 0.52 rad (30°) and varied in thick¬ness from 4.6 to 38 m (15 to 125 ft). Mining of these ore bodies was done by starting at the upper lateral ex¬tremities and retreating to the access openings. The timber square sets and cribbing were used as temporary support, the ground being allowed to cave as the mining retreated. It was found, however, that mining in such a manner was very inefficient; safety hazards increased be¬cause of the blocky and fractured characteristics of the ore and the weakness of the hanging wall. GENERAL DESCRIPTION The undercut-and-fill method of mining is now the primary stoping method used at Magma, and no pillars are left for later extraction. Four ore bodies are pres¬ently being mined. These ore bodies (see Fig. 1) dip conformably at 0.52 rad (30°) to the east with the host limestone and shale sediments, their average strike length is about 122 m (400 ft), and their thickness varies from 9 to 38 m (30 to 125 ft). The ore bodies are separated by varying thicknesses of barren rock. Three of them come together at various elevations primarily in the area of the main feeder fault, but there is an apparent horizontal displacement of about 23 m (75 ft) on the main feeder fault which complicates stope layout. The method as originally applied has been modified in order to mine more efficiently ore bodies that are 9 m (30 ft) or more in thickness. The modification was made to mine all the ore at a given elevation before dropping down for the cut below. The advantage of this is that mining is done on a horizontal plane and there¬fore muck removal can be mechanized. Also multiple faces are made available, thereby improving overall min¬ing efficiency. Another major change made was to carry a 6.7-m (22-ft) face when mining the top sill and a 6.4-m (21-ft) face when mining under fill rather than the former standard 3.35-m (11-ft) high face. This change lengthens the mining cycle and cuts mat prepa¬ration costs in half. Stopes are laid out (see Fig. 2) so that maximum mining panels are available and yet one stope crew will not tie up too much of the ore reserve. One stope might consist of as many as 20 panels, and these panels are divided evenly on opposite sides of the extraction cross¬cut. The stope layout is planned so that the maximum tramming distance to the orepass will not exceed 30.5 m (100 ft) on the crosscut and 38 m (125 ft) in the panel. Stope panel distances are sometimes exceeded when min¬ing to the extremity of the ore body. Tramming distance limits are determined by the efficiency of the com

Jan 1, 1982

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

The process design of a metallurgical plant follows logical steps, one built on another, to define the circuit requirements. The methodology used and documentation produced is the same for a pre-feasibility study, feasibility study or a complete design, regardless of the process complexity or the commodity. The only difference is the amount of detail developed at each stage. SRK Consulting, an independent, international consulting practice that provides focused advice and solutions to clients, mainly from earth and water resource industries, has consulted on many mining projects around the world. The company was formed in 1974 and now employs more than 1,600 professionals in more than 50 offices on six continents. According to SRK experts, the first element in plant design is collecting metallurgical testwork or operating data from an existing plant. The testwork identifies the process, the metallurgical recoveries and product qualities and establishes the process parameters for economic recovery of the commodity. Test samples must represent both the whole orebody and the feed over the life of the mine, showing the mineral?s variability. With this data available, the process design can be developed.

May 1, 2013

By A. Dell’Era, E. Ciro, C. Lupi

The paper explores the recovery of indium via electrowinning from sulfate baths, focusing on the impact of different cathodic supports (AISI 316L and nickel) on process parameters such as electrolyte composition, current density, and temperature. The study compares productivity, morphology, and structure of indium deposits on both cathodes, finding that nickel cathodes generally yield better results.

Nov 1, 2023

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicates the potential for scrap formation, validated through laboratory experiments with varying coke rate, basicity and holding time. The investigation discovered that smelting this combination could yield a metal product consisting of 59 percent Fe, 24.93 percent Cr, 7.56 percent Mn, 0.62 percent Ni and 0.93 percent Si. The optimum basicity was found to be 0.6 with 80 percent recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall carbon dioxide emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of US$330/t.

May 1, 2024

By C. D. Elifrits

The required reclamation of land disturbed by surface coal mining often results in the creation of some over steepened slopes which are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has indicated that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations will be summarized in this paper and field results shown.

Jan 1, 1986

In this paper, response surface methodology was applied to optimize the experimental conditions for the wet grinding of synthetic rutile. The effects of parameters such as rotation speed, solids concentration and duration of grinding on grinding efficiency were systematically investigated and the process conditions were optimized, using a nonlinear regression model based on central composite design. The statistical analysis of the results showed that in the range studied, the grinding efficiency of synthetic rutile was significantly affected by the rotation speed of the conical ball mill. According to results from analysis of variance, the value of the determination coefficient (R2=0.9989) indicates that the predicted values are found to be in good agreement with experimental values. The optimized experimental conditions were as follows: a rotation speed of 350 rpm, a solids concentration of 27.31% and a grinding time of 50.31 min, respectively. Under optimum conditions, the predicted grinding efficiency of 94.79% is obtained. The experimental values from the validation experiments were well within the predicted value of the model.

Jan 1, 2011

By J. F. T. Agapito

Two flat-lying trona seams 3-to 3.5-m thick, approximately 10 m apart, and at depths of 250 m are mined by room-and-pillar at OCI's Big Island Mine in Wyoming. Continuous miners and a yielding pillar system have contributed to improvements in resource recovery and productivity. Long-term stability with minimal subsidence is needed for a large portion of the mine beneath the Green River channel. This was investigated by computer modeling in 1990. Although results of the study indicated good long-term stability, recommendations were made for stress determinations to verify the model. Stress determinations made in 1997 showed pillar stresses 10% to 20% higher than the model stresses, and barrier pillar stresses 10% to 15% lower. This implies that higher panel stresses will be transmitted from the upper to the lower seam. A stability evaluation of the lower seam is planned before two-seam mining to assess entry widths and support requirements.

Jan 1, 1999

By John Relser

The production processes that are developed in the mining and minerals industry are manufactured to be exposed to very aggressive environments. Chemical, abrasion, and impact expose structures and equipment, steel or concrete, to a significant deterioration. This causes damage and adds high costs to operations that can be reflected in the destruction of equipment and structures in the arrest of the production process, which becomes very costly. Also, there is the potential for personnel accidents, which would require large sums of compensation for an employee, thus directly harming the image of the mining operation and company. Manufacturers of paints and coatings that have major centers for research and development (R&D Labs) distributed globally have developed high-tech products for durable protection from the elements for structures and equipment used in the mining industry. The difference between these paintings and coatings and what is normally known as conventional paints (e.g., those called domestic or decorative), is its chemical composition, structured around polymeric components that have highly resistant, chemical and physical properties to cope with extreme conditions to which they are exposed. With this, and only this, longer life of components can be achieved for equipment and structures used in the production processes of the mining industry. Today, in addition to the important features mentioned, some manufacturers of the paints and coatings dedicated to this highly modernized process have invested large sums of money in developing new products that add operational elements to the painting process. These coatings provide added value and significant performance to companies mining operations and that we can describe in three fundamental concepts:

Feb 1, 2014

By Wallace N. Thomas

The present interest in large diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a seven to eight thousand horsepower mill will cost from 1350 thousand to $600 thousand which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functions -- establishing a realistic compromise between cost and performance.

Jan 1, 1969