Search Documents

By C. Clark, J. Johnson, M. Stepan

"Shotcrete and mesh are often installed to control ground deformation, falls and ejection between bolts. The combination of mesh and shotcrete forms a panel or plate that is typically bent by ground extruding between restraining rockbolts. The ground pressure applied (that is, the resistance of these panels to bending) over large ground deformations is important for maintaining ground support safety. This paper describes a new test device that measures this resistance and its evolution over large deformations. Mixes of shotcrete, mesh and other components that can maintain significant support pressure are desired, a characteristic described as the “toughness” of support. Results show toughness depends largely on how shotcrete is integrated with other components. Shotcrete strength is less important. INTRODUCTION Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often called upon to do this (Figure 1). Applications are especially common in mines with squeezing ground or seismic loading. The support pressure maintained during ground deformation is key to the performance of these systems, and to protecting miner safety. However, the toughness of a design is difficult to estimate. Researchers at the Office of Mine Safety and Health Research (OMSHR) responded to this deficiency or “gap” by designing a full scale test device, described in this paper, and beginning a testing program. Some initial results from this program are reported to demonstrate test capabilities.BACKGROUND - TOUGHNESS Mining in ground that fails from the combination of in situ and mining induced stress is commonplace. Ground support elements are installed to reinforce such ground and preserve mine safety. Typically, the strength of support is considered key, and is used to prevent or halt yielding. However, ground movements driven by creep of weak ground or seismic loading may be impossible to halt altogether. In these cases, it is essential that support is able to yield with the ground in a safe manner while maintaining confining pressure that mobilizes the strength of rock in the immediate perimeter of the opening. In addition, it’s usually desirable to contain ground between rockbolts to protect miners from loose rock that might fall or be ejected. Shotcrete and screen are often employed, sometimes together and in combination with other support elements, to accomplish this function. A key characteristic of such a system is its ability to maintain support pressure through large ground deformations, a characteristic often called “toughness” – especially in support systems incorporating shotcrete. Toughness can be quantified as the work done during deformation (e.g. force x displacement)."

Jan 1, 2015

By J. Hunter

The Highland Uranium Project in Wyoming is an in-situ leach (ISL) facility owned and operated by Power Resources Inc. It is the largest uranium producer in the U.S. and the largest uranium producer by ISL in the western world. With its limited capital investment and low operating costs, the ISL technique has been demonstrated to be an effective and environmentally sensitive method for recovering minerals from these low grade and otherwise uneconomic orebodies.

Jan 1, 1996

By Ehsan Alavi, Sanjeer Yogendran, Savreet Singh

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel Project in Toronto extends approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. This project includes the installation of five intake shafts connected by 10.5 km of 6.3 m internal diameter tunnel and eleven drop shafts and vent shafts, connected to the tunnel by a series of adits. During the excavation of one of five intake shafts (20 m in diameter and 52 m deep), significant volumes of free phase oil and hydrocarbons were encountered. Due to the heavy inflows of the contaminants, excavation was stopped at the transition depth. The initial support of excavation needed to be redesigned, shaft had to be backfilled with CDF and installation of deeper secant piles are in progress to cut off contaminants. This paper outlines the initial plan for excavation as well as the design changes to the plan. The current status of the shaft excavation and lessons learned will be discussed.

Jun 13, 2021

By Ronald M. Fedrick

The microtunneling project for the State of Hawaii's Natural Energy Laboratory (NELH) facility in Kona, Hawaii, was awarded to Nova Group Inc., Napa, California. Nova has developed both microtunnel and deep pile cofferdam experience. Both of which would be required for this project. The project was designed by Makai Ocean Engineering of Honolulu as a continuation of the Ocean Thermal Energy Project (OTEC). The world's first OTEC plant has been successfully operational at NELH since 1982 netting approx 50 kw of usable electric power from a gross generation of 210 kw. A second plant designed to draw 39°F cold water from 3,000 ft below sea level and produce a gross output of 1 mw with a net 500 kw of usable power required 2 - 54 in. finished diameter pipelines. An ongoing problem with earlier offshore pipelines has been the damage to the near-shore pipes within the surf zone. The necessity for a deeper connection between the land based pipe and submerged sea pipeline was obvious. Earlier pipelines had been drilled and shot through the shoreline. This process was only practical at shallow depths. Makai Ocean Engineering and the NELH scientists looked at different methods to get the pipeline through the shoreline at a depth of 80 ft below sea level. Initially, the direction drilling method was proposed as the most potentially practical method. A contract was awarded and various attempts were made to complete a successful

Jan 1, 1995

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda's mine production goal was set at 500,000 tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: Combined the exploration and business development groups Formed teams to search for and respond to opportunity Made our geologists more business minded and our engineers more optimistic Went global Set clear thresholds, farmed out the marginal properties, fast tracked the others Focused reconnaissance exploration where we had a clear competitive advantage Became a "flexible" partner to both juniors and seniors Is it working? A number of successes, near successes, and outright failures are discussed. The main result is a much higher rate of opportunity flux which is essential for success in the mining industry.

Jan 1, 1999

By D. G. Krige

In the world mining scene, precious metals (particularly gold) have recently monopolized the attention in exploration as well as new production activities. As the major world producer of gold, South Africa plays and will continue to play a very significant role in this commodity. This role will, of course, have its consequential effects on the world's gold supply and, hence, also on the international price of gold. It is essential, therefore, and in the interests of all gold producers that the likely future pattern of gold production in South Africa be estimated such that some measure of production uncertainties can be predicted. For this purpose, some elementary geostatistical models will be used, and the main factors affecting the situation will be analyzed in broad outline only under the following headings: South Africa's basic gold ore potential in the three categories of: (1) ore remaining in existing mines; (2) extensions to existing mines via unexplored areas and/or reef horizons of lower grade; and (3) new mines, potentially deep or ultradeep. Cutoff grades - operating, marginal, and flotation, for the foregoing three ore categories, respectively. The availability of production, financial, and other resources required. Cutoff grades will, of course, depend on cost levels (operating and capital), future inflation and cost escalation trends in South Africa (SA), and/or gold price trends (in US$ and via the exchange rate in SA Rand terms). The differentials in inflation and escalation trends with those in overseas countries, mainly the USA, will, in general, set the scene for future exchange rate levels of the Rand. To predict the effect of various cutoff grades on future gold production from South Africa, it is essential to use geostatistical models. The applicability of such models is tested against past records of price, cost, and grade trends and then applied to the estimated ore potentials. These models were referred to briefly in a paper at a recent seminar on gold (Krige, 1986) but are discussed in detail herein. This lecture was intended originally to cover only technical aspects, but, in view of South Africa's position internationally and the possible effect of sanctions, internal unrest, and strikes on gold production, a brief reference to the third factor above (availability of production, financial, and other resources) seems appropriate.

Jan 1, 1988

By T. Braun

A greenfield open pit gold mine in Latin America suspended operations less than three years into an eight-year mine plan after a waste rock dump and heap leach facility sustained substantial damage from a deep-seated landslide. No injuries to employees were recorded because of the slow-moving failure. Due to early detection by the operations team, the owner had sufficient notice of the potential failure and successfully rinsed the heap leach facility prior to the failure event. Engineers estimated approximately 35 million cubic meters of mass movement below the waste rock and heap leach facilities. The original eight-year mine plan produced approximately 60,000 ounces of gold per year. After the failure, the owner terminated gold production, re-configured the mine site to a safe, standby condition and launched a detailed investigation into the root-cause of the failure. Approximately two years after the shutdown, legal interests filed a statement of claim and named three engineering design firms and individuals involved in the project. Several years of litigation, including discovery and deposition proceedings, followed as the legal process considered evidence spanning a 20-year timeline. Changes in project ownership and consulting firms during the development and operations phase complicated the process. In 2017, the plaintiff and last defendant settled. The author was involved as the corporate representative for one of the engineering design firms.

Mar 2, 2022

By S. Partney

Waste clay ponds are a necessary part of the phosphate rock beneficiation process. They are large, averaging a square mile in size; unsightly, in that they protrude 20 to 50 feet (6 -15 meters) above natural grade; stabilization and reclamation is slow; and they have had a history of catastrophic failure. The State of Florida has never published a specific rule regarding the configuration or height of these ponds, but has enforced numerous policies along these lines. The current rules are given and interpreted, along with the reasoning for current policy. In addition, an overview of the history of the policies, and an attempt at explaining the reasons for the changes that have occurred is given. The industry has been forced to make major monetary decisions, having effect for decades on mine economics, in a constantly changing regulatory environment. The Bureau of Mine Reclamation is confident that a direction of regulation has been solidified, but changes are still to be anticipated.

Jan 1, 1998

By Lukas Walder, Roland Arnold, Raphael Zuber, Richard Gradnik

This paper presents the construction of the ventilation shaft for the single-tube, doublelane Kramer tunnel. The project is located in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of Garmisch-Partenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million incl. VAT (US-Dollar 201 million), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for singletube tunnels is solved by a parallel escape tunnel passable for vehicles. For tunnel ventilation, an intermediate shaft has been designed with a depth of approximately 90 m (295 feet) and an inner diameter of 4.5 m (14.8 feet). All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). The geological and hydrogeological conditions, the change in the profile (from round to square geometry), and also the shaft being located at a high elevation presented a demanding technical and logistical challenge. The site arrangement with the pit bank was located in a cut, the slopes of which had to be stabilized with shotcrete and soil nails. This excavation was carried out from the fall of 2020 to the beginning of 2021 because construction operations had to be completed outside the nesting period of protected birds.

Jun 13, 2023

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By John S. Lagarias

While systems to remove sulfur oxides from flue gases have been used at coal fired power plants since 1931, critical need for flue gas desulfurization has only occurred since the late 1960s following the passage of the Clean Air Act Amendments. Commercial and advanced flue gas desulfurization processes (FGD) are reviewed. Advantages and disadvantages of the processes are discussed. Regulatory requirements leading to the development of FGD systems are identified. The location and operation of coal fired plants may be determined more and more by the regulatory requirements for sludge disposal, waste, water discharge and air emissions.

Jan 1, 1978

By W. A. Van Dyk

Hydrophobic particles with diameters between 1 and 3 mm are poorly recovered by conventional flotation techniques. A novel reverse flotation technique is described whereby coarse particles with surfaces rendered highly hydrophobic, repel the bubble films in a froth and thus drop through the froth under gravity, to be recovered as a sink product. Conversely, gangue or hydrophilic particles are supported by the bubble films in the froth and are therefore recovered as a floating product. Tracer tests were conducted in the cell in order to study the dynamic behaviour of solid particles in the froth. The effects of hydrophobicity, density, particle size and particle shape were investigated experimentally. The higher the hydrophobicity of the particles, the lower the recovery of particles as a floating product, while the recovery of particles as a sink product increases with an increase in particle density. Furthermore, a decrease in particle size results in an increase recovery of hydrophobic particles as a floating product. When treating particles of the same mass-to-surface-area ratio in the froth, flat particles would be recovered as a floating product in preference to cubic, disc-shaped, cylindrical and spherical particles, in that order.

Jan 1, 1995

By Christoph Mueller, Grzegorz Tabak

Basing on five years of experience, this paper discusses modern e-drive systems used in underground transport. This covers Energy distribution and cabling principles, inverters and motors as well as auxiliary aggregates. Also an overview of different regimes for battery charging and the energy management and the method of control of the traction are lined out: This means that throttle and brake are not handled separately, but integrated into “longitudinal control” algorithms which assure that a commanded speed is maintained while synchronizing the multi motor systems and taking into account the constraints imposed by e.g. slope grade and battery parameters.

Jun 25, 2023

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By J. Kretschmann, K. Sakamornsnguan

"Sustainable development is an influential ethical concept in modern mining management. However, the concept is not culturally neutral because it is based on Christian, Western values. These values can be very different from traditional values in emerging mining countries like Thailand, where Buddhist values are dominant. When applying the concept of sustainable development, these differences should be taken into account. Different values imply different interpretations of ‘good mining’. They have a significant impact on how mining operations are evaluated, perceived, operated and managed. This paper attempts to integrate Buddhist principles with approaches of the sustainable development concept. When local values are appreciated and maintained, mining companies and their external stakeholders can identify objectives and approaches that match with their own values and contexts. Practices based on this integrated ethic can help to promote sustainable mining and to minimize communication risks for enterprises in mining countries like Thailand. INTRODUCTION The objective of this paper is to integrate Buddhist principles to the application of sustainable development concept to mining activities. The structure of this paper is divided into four parts. An introduction provides basic information about Thailand, its mining industry and the role of Buddhism on the past development. The second part compares the differences between the sustainable mining framework and the implications of Buddhist principles on mining. In the third part, the core Buddhist teachings are integrated into the sustainable mining framework. This is followed by conclusions in the last part. THAILAND, BUDDHISM, AND MINING Thailand is a constitutional monarchy state in Southeastern Asia with a population size of around 65 million [1]. Its GDP in 2013 was 391 billion USD [2], predominantly deriving from manufacturing (38%), trade, transport and communication (24%), agriculture (8%) and mining and construction (4%). Still the largest part of the Thai workforce (39%) is working in the agricultural sector. The remaining part of the workforce is equally distributed across services, manufacturing, and mining and construction sectors. [3]"

Jan 1, 2015

Exploration for SX-EW copper deposits and plant operation depend largely on the copper and gangue mineralogy inasmuch as? they govern the feasibility of leaching. Mineralogical parameters are pivotal in identifying if an ore is suitable to dump, heap, thin layer, vat or agitated leaching and/or if the ore requires curing, bioleaching or alternate lixiviants. Problems in metallurgical testing, production leaching and recovery forecasting are very often related to lack of mineralogical data. This presentation will illustrate the use of quantitative mineralogical analysis for exploration, acquisition assessment and optimization of copper leach operations.

Jan 1, 1996

By G. M. L. Robinson

Mineral Processing Wastes, as defined by the Environmental Protection Agency (EPA), has determined that most of the mine wastes will be regulated pursuant to subtitle D (Solid Waste Regulations) of the Solid Waste Disposal Act while specific mine waste categories will be regulated within the framework of the Toxic Substance Control Act. Though EPA's determination currently relieves the industry of the regulatory constraints mandated by the Resource Conservation and Recovery Act (Hazardous Waste Regulations) Subtitle C regulatory framework; the industry is not granted immunity from historical or current environmental regulations related to listed or characteristically hazardous or solid wastes. Because of the current regulatory trends and the need to implement cost effective remediation alternatives; advanced currently available on-site remediation technologies are available to minimize, reduce, contain or prevent environmental impacts related to mining and processing activities. In light of industry technical needs, an overview of the research and commercially available remediation technologies will be discussed and a brief discussion of the strengths and weakness of each technology will be presented. Technologies to be discussed includes stabilization, solidification, soil wash, soil flush, thermal distillation, pump and treat, metal extraction, centrifuges, filter presses, bioremediation, and incineration.

Jan 1, 1992

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By E. A. Rychkun

Mining and environmental objectives have traditionally been in conflict. This conflict reflects a delicate balance between the need to spend money to protect the environment, and the need to save money by extracting minerals efficiently. In an increasing number of cases, profit margins diminish rapidly with new environmental regulations and reactionary measures. Forced cleanups and increasing restrictions are unwelcome expensive processes. A practical solution lies in planning rather than reacting. This requires the ability to precisely quantify and qualify environmentally sensitive problems by providing effective engineering tools to model, visualize and analyze subsurface conditions. Prevention of environmental conflicts, and effective cost control are both rooted in the mining company's ability to construct accurate models, monitor changes, assess contamination risks and to design effective remediation plan. This paper presents a case study where these issues are addresses through the application of a new and innovative technology.

Jan 1, 1993