Search Documents

By Qingwen Shi, Brijes Mishra

The abstract discusses the use of numerical simulations to investigate roof fall in underground mines. It highlights the advantages of the discrete element method (DEM) in simulating large strain problems and fracturing processes, while acknowledging its computational limitations for large-scale problems. The study presents a 3D numerical model coupling the finite difference method (FDM) and DEM to simulate laminated roof failure in a coal mine. The model represents the laminated roof with bonded particles and discontinuities, while the surrounding rock is represented by continuum zones. The research analyzes the fracturing of the laminated roof as the entry advances, demonstrating the coupled method's ability to reproduce laminated roof failure.

Mar 17, 2022

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

By Lon Santis, Gregory M. Rumbaugh, Christopher Mark

This paper examines the relevant theory, experience, and past practices relating to development mining near gas or oil wells. It addresses setback distance for both coal and stone room-and-pillar mining. This study also involved a review of accident reports involving well interceptions and downhole well surveys. It provides technical considerations for decisions regarding safe setback distances for development mining throughout the United States. The study’s scope is limited to mining near active or inactive (i.e., non-producing, abandoned or inadequately plugged) wells with known surface locations.

Jun 25, 2024

By R. Cook

Knowledge based applications are becoming important to Associated Manganese for efficiently dispatching ore of appropriate grades to customers on time. The G2 expert system shell has been used to develop blending and scheduling applications using a combination of object-oriented rule based, procedural, and heuristic approaches. The blending application, for example uses a heuristic approach for creating blends from thousands of small stacks of manganese ore of various grades and sizes, to meet customer specifications while fully exploiting the available inventory. Data capture and data warehousing have become important issues, and the Internet shows strong potential for distribution of pre-processed information.

Jan 1, 1997

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By D. J. McParland

This paper will deal with some of the considerations which, were involved in the design and construction of the uranium mills in the Elliot Lake area . These plants, eleven in number, range from 1500 to 6500 tons per day milling capacity. Most references are with respect to the seven plants in the Rio Tinto Group which have a combined milling capacity in excess of 20,000 tons per day. In dealing with such abroad subject as mill design, one has the choice, of covering a few specific problems in great detail, or else attempting to cover many subjects superficially and briefly. In preparing this presentation, an attempt has been made to compromise on these extremes, and to select some interesting illustrations which are of general interest in the field of mill design, and of value to persons concerned with mill design broadly, beyond the field of uranium mills.

Jan 1, 1959

By E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Leadership is a critical component to an organization’s safety culture and influences the ways that health and safety is enacted on site. Therefore, it is not surprising that improving leadership will also improve safety. Worker perceptions of management practices are shaped through unique leader-employee interactions over time. However, few details are known about the communicative support (i.e., emotional, informational, and tangible) offered by supervisors and its impact on miners’ perceptions and performance. Using pre and post-interview data with 20 supervisors and 48 workers during six-week interventions, researchers identified positive and negative instances of supervisor support and its implications on worker performance. This paper highlights the common support tactics offered by supervisors and desired by workers to help practitioners identify ways to improve their safety culture and subsequently, the proactivity and compliance of their workforce. INTRODUCTION Supervisory leadership is a critical component to the effective implementation of an organization’s health and safety management system (HSMS). Specifically, supervisors serve as representatives of an organization and their actions are indicative of the organization’s safety culture (Eisenberger et al. 1986). Senior management has been shown to serve as a frame of reference for guiding safe behaviors in the workplace (Mearns et al. 1998) and, more recently, research has related supervisory enforcement to workers’ safety compliance (Petitta et al., 2017). Therefore, it is not surprising that by improving leadership, perceptions of management and subsequent safety outcomes are likely to improve as well (Zohar, 2002). Perceptions of management are shaped through unique leader-employee interactions over a period of time (Hofmann and Morgeson, 2004, 1999). How these unique interactions impact worker performance, however, remains unexamined. As a result, understanding how supervisor-employee relationships operate in high-risk environments is unclear (Mirza and Isha, 2017; Denis et al., 2010). A starting point to better recognize the idiosyncrasies of these relationships is by way of examining the communicative support offered by front-line management and received by industry workers. To this end, this paper uses pre- and post-interview data to study the communicative aspects of supervisor-employee interactions at mine sites. The analysis uses a social support framework to identify positive and negative instances of supportive communication. From interview data with 20 managers and 48 mineworkers, data emerged that shows how supervisors’ unique types of support contribute to workers’ perceptions, motivation, and follow-through of safe work behavior.

Jan 1, 2019

By W. G. Prast

The role of governments as a factor in the international non-metallic minerals industry can take several forms. Classically, the government acts as a taxing agent, collecting part of the economic rent on behalf of the country from private-sector mine operators. In addition to its taxation policies, the state can and does provide the practical commercial framework of regulatory and fiscal incentives and restraints that shape the activities of the mining firms. In addition to its functions as an agent of the public interest, the government can choose to take a more direct stake in the mining industry, and has done so in the instance of several industrial minerals that are actively traded on world markets. In this paper, the actions of three governments are reviewed and the consequences of their actions are examined.

Jan 1, 1981

By Michael G. Nelson, Amy Richins, Ashley Hodgson, W. Pratt Rogers

"Sociotechnical systems are everywhere in the modern industrial world. Sociotechnical systems describe how humans interact with technology throughout a variety of processes. These systems are prevalent in modern industrial settings, such as operating mines. Safety and health management systems (SHMSs) are complex sociotechnical structures designed with the aim of managing and reducing occupational risk. U.S. mining companies are voluntarily adopting SHMSs to supplement regulatory safety compliance efforts. Like all complex sociotechnical systems there are a wide variety of approaches and adoption philosophies around a SHMS. Many SHMSs suffer from high levels of redundancies, which manifest themselves in diverse ways: duplicate processes, forms, permits, and tracking mechanisms. These redundancies have severe impacts on the overall system and absorb critical culture and leadership “energy”. A recent study initiated by the University of Utah and sponsored by the Alpha Foundation is investigating the effectiveness of SHMSs across 15 different U.S. mining sites. A large amount of data has been captured to help characterize elements of SHMSs and correlate their impacts on safety outcomes. Many variables were assessed in the study. Those of importance to this paper are the variables describing the robustness of the sociotechnical aspects of the SHMS. Two such variables are the overall integration of the SHMS within the whole system and how data is managed. Data management in this context deals with the approach to capturing, analyzing, and acting on data within the system. As well, systems are integrated around controlled, data-sharing mechanisms. It has been found that wide variety of approaches has been taken to integrate the SHMS within the governing management philosophy at a given site. A series of case studies is presented that develop some specific best practices for proper data management and integration of SHMSs.Introduction and Project Background Managing occupational health and safety can be done in many different ways, and with many different approaches, but is often based on the host country’s regulatory and industrial culture. However, many companies have extended their effort beyond the regulatory requirements of their host nation and have implemented Safety and Health Management Systems. The goal of these efforts is to reduce and eliminate occupational risk. Many health and safety practitioners have a hard time justifying various elements of health and safety management. There is a lack of institutional knowledge that measures and assesses the effectiveness of these Safety and Health Management System (SHMS) elements. To better understand the effectiveness of SHMSs the Alpha Foundation has funded a research project with the University of Utah. The title of the project is “Characterization and Effectiveness of Safety and Health Management Systems in the U.S. Mining Industry.” The research team will assess the SHMSs of 15 United States mine sites. The outcome of the project will be a method to characterize the strength of the SHMS elements, assess a culture and leadership index, and finally establish correlations between elemental risk and safety outcomes. The study is currently in progress. However, many important outcomes have already been observed, particularly on the data management practices within an SHMS."

Jan 1, 2017

By A. Adhikari, P. Tukkaraja, S. Jayaraman Sridharan

Shafts are critical components of the mine ventilation systems and contribute significantly to the mine ventilation pressure. Estimation of shaft pressure losses is an important aspect of mine ventilation planning and shaft frictional pressure losses are extensively studies. Shock losses contributed by shaft buntons are estimated using the interference factor model developed half a century ago. This study aims to develop a better performing prediction model for shaft buntons using state of the art experiment and numerical data, and machine learning techniques. Results show that the present prediction model is performing poorly, and the prediction performance can be improved by incorporating additional predictor variables. The Artificial Neural Network standardized Machine Learning model developed in this study is able to predict the shaft bunton shock loss with high accuracy (R2 = 0.956).

Jun 25, 2023

By Bartłomiej Bursa, Paweł Stefanek, Paweł Stefaniak, Sergii Anufriiev, Wioletta Koperska, Maria Stachowiak

The article presents the main functionality of the DSS class system for monitoring and stability assessment of tailings storage facilities. The presented demonstrator was deployed on the example of the Żelazny Most reservoir - the largest active facility of this type in Europe and the second one in the world. Considered a high-risk structure, it demands a system capable of online analysis of big data from various sources using machine learning, 3D modeling, or GIS mapping with the functions of interactive time-spatial analysis. In this paper, we present a complex calculation module with an integrated user interface.

Jun 25, 2023

By Walfrid Been

There are no particular nor unique features of iron mining that are not shared in some degree by all mining ventures everywhere. There are, however, at least three problems that have acquired a special emphasis from a unique cause. That cause is the embarrassment of riches under which the industry is suffering. The most obvious' feature of iron mining today is the copious abundance of usable ore and its almost universal distribution over the face of the earth. By the term "usable ore" is meant ore that is amenable to reduction by the usual and conventional processes. Amidst this plenty, three problems become acutely emphasized: 1. The geographic location that will provide a mine with the best market opportunity. 2. The size of the orebody that will be required to' return the preproduction investment. 3. The geometry and configuration of the orebody that will permit quality control measures to be effectively executed.

Jan 1, 1964

By W. C. Patrick

Introduction The availability of a thorough, simple-to-use roof fall classification system is desirable for several reasons. First, such a system would expedite the reporting of falls for the purposes of estimating material removal costs, analyzing damage levels, and complying with federal regulations to report falls in certain areas of the mine. Second, the classification system would allow the mining engineer to record falls routinely with little time and effort expended. This would encourage him to make observations concerning what type of roof support would work best in a given situation. Third, and probably most important, an adequate roof fall classification system is the first step toward developing a means of predicting the occurrence and extent of future falls. It was with these three reasons in mind that the following classification system was developed. The type of classification chosen reflects the background of the developer and the intended purposes of the system. Hylbert has proposed a geologic-based classification which groups falls as to structural and compositional origin. The need for similar systems is noted by Cox and by Ferm and Melton. Each of these researchers is confronted with a situation requiring a relationship between local geology and roof fall occurrence. Such a relationship would allow the prediction of the relative frequency of falls from a knowledge of local geologic features. The current research is aimed at fulfilling somewhat different requirements, as noted above. Fall geometry has been chosen as the basis of the classification system so fall type can be reported independent of local geological, environmental, and tectonic conditions. This approach parallels that used in the common slope failure classification with groups failures relatively independent of

Jan 1, 1977

By B. J. Timmons

Depending upon which of two letters describing the theme of the session I chose to honor, the subject choices because either one or three. They were: "Applied Research and Exploration and Discovery" or "Applied Research in Exploration and Discovery." The final choice; to partially ignore both of them. That minor difference in meaning may be appropriate here, inasmuch as very minor research/exploration differences may also have profound impacts on discovery. To further set the stage, I consider myself an Industrial Minerals geologist, and more specifically primarily associated with basic construction materials crushed stone and sand & gravel. My remarks will apply primarily to those materials. Therefore, when the discussion instructions included emphasis on beneficial aspects (to name a few): "drill target definition; elimination of ore potential; ore forming environments; alteration studies, and isotope analysis," problems became apparent. Evidently, and although this was a form letter, the drafters of that letter had no idea what was involved in research for a construction materials source. My task may be great.

Jan 1, 1995

By B. Boberg

Annual requirements of uranium to fuel the 441 currently operating nuclear reactors in the world is 170 million pounds U3O8 (65,385 tonnes U). 2005 global production was 108 million pounds (41,595 t U), of which only 2.7 million pounds U3O8 (1,039 t U), was produced from US uranium deposits. US nuclear utilities represent 26% of the global nuclear capacity but only obtain 2.5% of their supply from US uranium mines. Since 2002 annual global production increased from 93 million pounds U3O8, a 15% increase and the US production increased from 2.3 million pounds to 2.7 million pounds, a 17% increase. Reasonably Assured Resources (RAR) of 12,332 million pounds U3O8 (4.7 million t U) are reported from a wide variety of countries and types of uranium deposits. This RAR suggests that there are significant global uranium resources potentially producible at a price of $50 per pound U3O8 ($130 per kg U). Table 1 shows the distribution of global uranium resources. This table, prepared from historic data maintained by the World Nuclear Association, does not include some areas of the world that are currently considered to contain significant resources of uranium such as Mongolia. Table 1 suggests that the United States contains the fourth largest uranium resource in the world with 890 million pounds U3O8, behind Australia, Kazakhstan and Canada in resources that are producible at a price of $50 per pound U3O8 ($130 per kg U). Within the US, the states that demonstrate the greatest amount of uranium resource are Wyoming, New Mexico, Texas and the Four Corners Area of Arizona, Colorado and Utah.

Jan 1, 2007

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By Gerrit V. R. Goodman, Fred N. Kissell

The Bureau of Mines has evaluated the effectiveness of the safety elements used to prevent tunnel methane explosions. These fa1l under the general categories of better ventilation, better gas monitoring, reducing ignition sources, and improved worker training. For this evaluation, a technique called fault-tree analysis was used to analyze questionnaire responses from 27 tunneling experts. This analysis allowed us to rank the effectiveness of each safety element, and indicates where money is best spent to reduce the chance of a methane explosion. Results indicated that large decreases in the explosion hazard only take place with the simultaneous application of several elements. Most of these involve a human component - the everyday vigilance and awareness of those working underground.

Jan 1, 1991

By P. K. Sims

One-day field trip via U.S. Highway 6 and Colorado Highways 119 and 279 from Golden, Colorado to Idaho Springs. This field trip provides an opportunity to observe aspects of the Laramide ore deposits in the Central City and Idaho Springs mining districts and the Proterozoic basement rocks, which host the ore deposits.

Jan 1, 1986

By Anil Kumar

In underground mine production units that employ discrete-vehicle face haulage, feeders are used in the belt network so that vehicles can unload rapidly without transmitting to the conveyor network the high material flow rates that result from rapid unloading. They prevent production bottlenecks at the face, while reducing capacity requirements for downstream materials handling equipment. Similarly, surge bins may be installed at intermediate locations in the network to smooth flows from a number of upstream sources, thereby reducing downstream belt capacity requirements. This paper introduces new stochastic process models to temporally describe loading patterns from unit operations and techniques for computing the probability of various fill levels for the feeder or surge bin. These results may be used to analyze the effect of alternative bin or feeder capacities and discharge rates on the performance and costs of the materials handling system.

Jan 1, 1994

By J. D. Miller

The sedimentary western phosphate deposits of Idaho, Montana, Utah, and Wyoming tend to be calcareous and generally carry a significant amount of dolomite along with collophanite. In some cases, such as the Smokey Canyon Mine, Afton, Wyoming, the ore will also contain mudstone, and in this case the aluminosilicate minerals (clay, feldspar, etc.) together with some dolomite are floated from the collophanite in column flotation cells with an amine in order to meet product specifications (31 % P205) (Service et al.). In other cases, such as the SF Phosphates Limited Mine, Vernal, Utah, the ore is treated by traditional fatty acid flotation of the collophanite with mechanical flotation cells (Weber, 1986). Preliminary tests have now been conducted to evaluate air-sparged hydrocyclone (ASH) technology for the flotation of western phosphate ore. For this preliminary study, samples were taken from the hydrosizer overflow stream (18-21 % P205) at the SF Phosphates Limited Plant in Vernal, Utah for scavenger flotation testing with the 2-inch ASH system in laboratories at the University of Utah. Selected design and operating variables are being studied, and the initial results show that satisfactory separations can be achieved by high-capacity ASH flotation at appropriate operating conditions. For example, with single-stage ASH flotation 80% recovery can be obtained with a scavenger concentrate grade of about 26% P2O5. These results are comparable to, or better than, those obtained at SF plant operations with conventional flotation cells and suggest that ASH flotation technology can be used to good advantage in the phosphate industry. Of course, research should be continued to consider other process streams, optimize the separation efficiency, and evaluate larger diameter ASH units.

Jan 1, 1993