Search Documents

By John A. Cherry

Groundwater monitoring conducted at an acidic uranium-tailings impoundment in Wyoming and at one in Ontario indicate that at these unlined impoundments situated on unconfined sand aquifers, there exist well-developed plumes of contaminated groundwater. In the literature similar results are reported for three other unconfined aquifers at mill sites in Wyoming. The plumes extend for distances of several hundred to a few thousand metres from the impoundments. They have a zone of low pH beneath and adjacent to the impoundments and a larger zone of near-neutral pH that extends to the outer limits of the plume. The low-pH zones are generally small compared to the neutral-pH zones because the advance rate of the fronts of acidic tailings-derived water is slower than the average velocity of groundwater which controls the advance of the high pH zone. The retardation of the acid fronts is a result of geochemical reactions that cause hydrogen-ion consumption in a slowly-advancing neutralization zone. Within each of the plumes, the low-pH zone has high concentrations of transition metals, heavy metals and radionuclides. In the neutral-pH zones all of the metals and radionuclides occur at significantly lower concentrations and are generally at levels much below those specified in national drinking water standards. An exception at two of the Wyoming sites is uranium, which exists at levels close to the drinking water limit. A second exception is ferrous iron at the Ontario site, which occurs at high concentrations throughout most of the plume. The carbonate alkalinity at this site is much lower than at the Wyoming sites. The field data indicate that even in very permeable aquifers with a low content of silt and clay, there is normally a considerable capacity for acid-front retardation. To take advantage of this capacity to control contaminant movement in the design, operation and decommissioning of tailings impoundments, it is necessary to be able to predict the rate of acid-front movement. This predictive task has two primary components. The first is to identify the important flow paths from the tailings through the groundwater system and the second is to determine the degree of acid-front retardation that will occur as the tailings-derived water moves along these flow paths. Relative to these two tasks determination of the effects of hydrodynamic dispersion is generally of lesser importance and simple approximations that do not involve field or laboratory tests are probably adequate. In order to effectively apply the acid neutralization concept to the prediction of subsurface contaminant migration at uranium-mill tailings, improved representations of hydrogeochemical behavior of iron and aluminum in the neutralization zone and of the consumption of hydrogen ions through reactions with carbonate and aluminum-silicate minerals are required. Along with the hydrogen ions contained in the tailings water the ferrous iron represents a large potential source of acid but the extent to which ferrous iron converts to ferric iron to produce acid is problematic. Detailed hydrogeochemical evaluation of existing contaminant plumes and the performance of laboratory experiments under appropriate redox conditions ore prerequisites for the improvement of predictive models. However, the existing field and laboratory data provide a basis for preliminary predictions of contaminant migration from acidic uranium tailings impoundments.

Jan 1, 1982

By Peter N. Calder

There is little doubt that the stability of both highwalls and spoil piles is essential to efficient strip mining. Accurate determination of the appropriate geotechnical parameters will pay dividends during mining, but only if the mine operation closely follows the engineering plans which have incorporated These factors. Productivity is invariably higher in mines where failure of highwalls and spoil piles does not occur. This is the result of the reduced rehandle and better working conditions found in stable mines. Control of the waste piles and highwalls also leads to better coal recover since failures can result in the burial of uncovered coal, which is then lost to mining. Safety is an important consideration. The importance of providing a safe working place for employees and of protecting costly mining equipment is hard to overemphasize. For miners, working in areas where instability exists, the degree of hazard involved in their occupation is increased particularly where night operations are involved. It is true, too, that there have been many cases where loading equipment has been buried and severely damaged by failures.

Jan 1, 1980

By K. A. Heasley

The objective of this paper is to back analyze the August 6th, 2007, collapse at the Crandall Canyon Mine in Utah, in order to better understand the geometric and geomechanical factors that contributed to that collapse. In this work, the LaModel boundary-element program, along with the best available information, is used for the back analysis. To initiate the analysis, a six-step base model of the mining in the Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters, rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis, a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) overall, the area was primed for a massive pillar collapse because of the large area of equal-size pillars, 2) the abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse and 3) from the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2010

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By H. D. Lelono, M. Walden, G. Johnson

3D modelling can be used throughout the mine lifecycle and has proven to be a powerful tool for consultants and mining companies. One of the most significant benefits of 3D models is their ability to enhance collaboration, communication, and understanding between the mine owner, design engineers, and other relevant stakeholders that have a shared interest in responsible mining and site management. Tailings and mine waste management is an interdisciplinary effort that requires effective coordination and communication between a wide range of consultants, operators, and stakeholders alike. The increased emphasis on Environmental, Social, and Corporate Governance (ESG) highlights the importance for mine operators to engage and communicate with all parties involved in the planning, permitting, operation, and closure of mine sites. 3D models are valuable tools that can be used for development of geotechnical conceptual models, allowing for improved design and monitoring of Tailings Storage Facilities (TSFs). A clear conceptual understanding of a TSFs subsurface geology and foundation characterization is essential for proper tailings management, design, and planning. Visualization with 3D modelling can simplify the interpretation of the, oftentimes intricate, mine sight subsurface settings and allows for quick and effective geotechnical conceptualization. 3D models can be used to identify data gaps, optimize field investigations, and streamline the development of numerical stability or groundwater models. They can help communicate the complex nature of subsurface and TSF interactions in a clear, concise, and accurate manner to both technical and nontechnical stakeholders. This paper discusses some of the benefits of 3D modelling in relation to geotechnical analysis for tailings management and provides methodologies for how to improve upon some methodologies that are considered industry standards.

Feb 1, 2023

By K. N. Hebbar, R. G. Reddy

Spent potliners (SPL) were declared hazardous waste under RCRA (K088) in July, 1990. The glass formation characteristics of the SPL was studied. The SPL glassy matrix were analyzed using X-ray diffraction and optical microscopy. Results showed that SPL can be fixed in a glassy matrix with the addition of sand and limestone. The optimum amounts of additives were determined for obtaining the best glass formation characteristics.

Jan 1, 1995

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By Kostas Fytas

A computer package has been developed which is capable of evaluating alternative production schedules (long and short range) of an open pit mine once the ultimate pit limits have been defined. The model user can choose the best alternative according to cash flow considerations and the particular mining conditions. The package involves a combination of simulation for long range production scheduling and linear programming for short range scheduling. The simulation model based on an iterative technique, maximizes the profits within each long scheduling period (eg. year or sixth month period), and at the same time defers stripping as long as possible. A minimum exposed ore quantity is kept at the beginning of each mining period. The final long range schedule satisfies a set of constraints for each period, mainly ore quality and quantity constraints for ore and waste. An interactive smoothing procedure at the end of each period results in a schedule that is feasible in terms of mining practice. Finally a cash flow analysis model carries out cash flow calculations so that the user can select the best alternative. The linear programming model, based on a certain number of shovel regions, defined interactively by the model user, calculates the optimum production schedule for each short period under consideration, so that a set of constraints is satisfied.

Jan 1, 1986

By G. M. Molinda

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

Jan 1, 2008

By Keith A. Heasley

The objective of this paper is to back-analyze the August 6th ,2007 collapse at the Crandall Canyon Mine in order to better understand the geometric and geo- mechanical factors which contributed to that collapse. In this work, the LaModel boundary-element program along with the best available information is used for the back- analysis. To initiate the analysis, a six step base model of the mining in he Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters: rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis , a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) Overall, the area was primed for a massive pillar collapse because of the large area of equal size pillars, 2) The abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse, 3) From the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2012

By S. G. Dixit

Alunite (KAl3(SO4)2(OH)6] is one of the important nonbauxitic resources for aluminum in U.S.A. The major gangue material associated with a unite ore body is quartz. Experimental results indicate that oleic acid flotation of alunite is quite effective in upgrading the ore. The flotation chemistry of the alunite/oleate system has been investigated using various techniques such as: hallimond tube flotation response, measurement of adsorption density using I4C labeled oleated, electrokinetic measurements, infrared spectral studies, contact angle measurements and thermochemical measurements using an isothermal microcalorimeter. Alunite has been found to float readily with oleate in the pH range 4-10.5 and its flotation response is enhanced at higher temperatures. The PZC of alunite has been determined to be at pH 7.2 ± 0.15 which agrees with what would be predicted from solution chemistry and from the flotation response with physically adsorbed collectors. Infrared spectra show a specific peak in the range 1585-1600 cm-1 which has been attributed to the formation of an aluminum oleate surface species. Both adsorption density measurements and infrared spectra indicate that during adsorption multilayers are formed. The heat of adsorption of oleate on alunite has been found to be endothermic and of the order of 4-6 KJ/ mole.

Jan 1, 1980

By O. R. Bell

In Australia's remote North West are located the operations of Cliffs Robe River, one of the world's largest iron ore projects. Initial project cost was $US300 million and required the construction of a deepwater port, two toms for 3000 people, a 105 Mw power station and 170 km of railroad, all in harsh, arid country over 1300 km from the nearest industrial centre. The ore occurs as goethite cappings on scattered mesas and averages 57 percent iron. All aspects of the project are reviewed from pre-operational research, through project construction to current operation.

Jan 1, 1979

By A. D. Hammond

Until recently, the volumes delivered and unloaded from heap-leaching pads have been estimated by manual methods at Wharf Resources' South Dakota operation. In August 1989, the Engineering Department acquired the MINE-SURVEY software developed by GEM COM Services, Inc. of Vancouver, Canada, as part of a mine planning/grade control software package. The implementation of MINE-SURVEY for pad control resulted in a cost-effective tool to provide accurate and prompt estimates of ore delivered or unloaded from the pads. Volumes can be calculated in a matter of minutes as opposed to hours or days. Another benefit is the ease of comparison of as-build and designed volumes, plotting cross-section in any orientation, importing into AUTOCAD, validation of ore densities and truck factors. This paper describes the application of the MINE-SURVEY systems in heap leaching pad volumetrics.

Jan 1, 1991

By Patricio A. Riveros

Various types of commercial ion exchange resins were evaluated with respect to their ability to extract gold from cyanide leach solutions. Large differences were found among the various resins in terms of selectivity and gold loading. The hydrophi­licity and the charge density appear to be the main factors that determine the resin characteristics. Polystyrene weak-base resins, such as Dowex MWA-1, exhibited the best all-round performance.

Jan 1, 1990

By Robert Martinez

A proven high grade reserve of gold mineralization located in Mexico is evaluated to determine which gold recovery process is best suited for this deposit. The processes evaluated are; Heap leaching, Vat leaching and a CIP circuit. All qualify as viable options, however each one presents a different economic picture which is impacted substantially by the financial constraints of the project. Taking this into consideration the most economic process was selected.

Jan 1, 1987

By Juan P. Camus, Sergio G. Jarpa

INTRODUCTION Chuquicamata mine is a large copper open pit located in the north of Chile. It has been in production for more than 80 years and now is in the later stages of its life with declining grades and increasing haul distances. As any old mine with long established organizations and procedures, it has faced one of the most difficult managerial problems: to conduct changes. Since 1994, the new management team has been devoted to a modernization pro- gram focused mainly in restructuring business operations. downsizing the labor force and introducing a mine planning pro- cess consistent with the company's goal. The explicit identification of the latter issue has been made because of the management’s conviction about the importance of it in the profitability of the business. The mine planning process at Chuquicamata mine has evolved from an old manual technique towards a modern computarized system, however the fundamental aspects and the procedures involved in this process have been the same. For in- stance, the cutoff grades policy has not changed during the last said 20 years, regardless of the changes to grade distribution, commodity prices, plant capacities, etc. To review and rethink this process, the strategy was to work with a small group of inside engineers and the management in order to interact with several mining consulting firms. The idea was to open a discussion about the fundamental principles used in the mine planning activities and, at the same time, to explore new ideas to improve the operating practices that have been followed for a long time. Thus, the goal of this paper is to present the mine planning approach that was the result of this work and the improvements that were obtained. THE CHUQUICAMATA MINE The Chuquicamata division is one of the five operations of Codelco and is currently devoted to operating the Chuquicamata mine; a copper open pit, concentrator, smelting and refining complex. It also operates Mina Sur which consists of an open pit mine, a leaching-solvent extraction and electrowinning process. There is also a dump leaching and a Sx-Ew plant for treating the low grade suifide ore (under the cutoff grade) from the Chuquicamata mine. Prior to reviewing the mine planning process, capacities for the Chuquicamata sulfide line were 640 000 tpd of run of mine material, 160 000 tpd of ore and 4 200 tpd of concentrate. This meant a total annual movement of around 230 Mt in the mine and a treatment of 57 Mt in the concentrator with a stripping ratio of approximately 3: 1. The old exploitation strategy consisted of an "open scheme", which means that all benches must have a berm with enough space to allow the traffic of large haulage trucks. This fact implied working with a great flexibility, but the consequences were flat slope angles. One of the reasons for using this operating practice in short term planning was that the grade consistency from the pit has always been a controversial variable. Schedules were designed to meet grade targets accurately and they were modified immediately when deviations become apparent. This reality led to working with a great deal of independent pushbacks and it required flexibility in the traffic system. The cutoff grade policy has been the same for a long time and the figure was 0.5 %CUT either for sulfide or oxide ore. This was the reason why a balance was produced between the mine and the concentrator. The mine is operated principally with benches of 26 m but in the upper part of the pit there are benches of 24 and 30 m. The main production equipment is shovels of 28 and 34 yd3 along with trucks of 200 and 240 st. Regarding the crushing facilities, there are two main systems located inside the pit and an old one in the periphery, close to a stockpile and near the concentrator. In the north part of the pit there is a crusher for waste material and in the north-east area is located the ore crusher facility. Both restrict a significant area of the pit and the mine sequence is considering to move the ore crusher again to the south-east sector where it used to be located. Relating to the waste crusher, the idea is to move it up to a bench near the surface in order to use the same conveyor belt and, at the same time, liberate an important sector. THE MINE PLANNING PROCESS The objective of the mine planning process is to develop a mine plan for the life of the deposit, in harmony and consistent with the company's goal. It includes the origin and destiny of tonnages and grades from the mine(s), along with the necessary resources to carry out this plan such as: fleet requirement, consumable goods, manpower, etc. From the financial point of view, it means to establish the cash flow for each time period of the mine life. That is. the revenue, capital investment and operating cost associated with each period of the plan. The fundamental principles involved in the mine planning pro- cess have been a controversial issue for a long time. One of the reasons for these divergent views could be produced by the difficulty of modeling a complete extraction policy for a geological re- source. This particular problem has to deal with several decision variables that are time dependent. So far, there is no mathematical formulation for managing such a problem, and the approach to solve it is based on a circular analysis combined with certain heuristic tools. So, a global model rather than a formula, requires a clear understanding of mine operations as well as economic theory and its application to a non-renewable resource. In order to manage this complex problem, the mine planning process can be conveniently split off in three stages which are conceptual, feasibility and operational planning. The characteristics of each stage are basically the timeliness in which they are developed and the kind and number of variables involved. Thus, conceptual planning is devoted to the definition of key variables like: the size of the operation, mining method, extraction se-

Jan 1, 1996

By Robert L. Marovelli

The major mining health and safety problems of concern to United States Government and private industry researchers in 1981 included the difficulty experienced by longwall operators in complying with the Federal 2 .0-mg/m3 respirable dust standard, the accident rate associated with falls of ground and materials handling hazards, and the upsurge in the incidence of disasters after the steady decline in recent years. Although the many mines and manufacturing companies involved in the research projects to be described are not specifically identified, it is important to note their significant involvement. This is not by way of acknowledgement, but rather to establish that these projects, using mostly Federal funds, represent close cooperation between the U.S. Government and the mining industry. The ongoing work to be described on the development of critical longwall dust control technology is a classic example of Government-industry participation through the phases of problem identification, planning, cost-sharing, and implement at ion.

Jan 1, 1982

By H. R. Manouchehri

In flotation practices, as particles become finer, such as smaller than 20 μm, process efficiency declines markedly. Selective agglomeration of fine particles is a technique to enhance the recovery of fine valuable minerals in flotation circuits. Different agglomerating methods have been introduced and tested. One method that has recently received much attention is to make use of magnetic force to aggregate fine particles. A selective aggregation of fine paramagnetic particles, such as sulfide minerals, can be achieved in the high-intensity magnetic field prior to or during flotation. The method is simple, selective and effective for fine particles and has low operational cost, though a minimum magnetic susceptibility for fine grains is required to promote the process. In this paper, the implementation of the ProFlote magnetic conditioning device in Boliden’s Garpenberg old concentrator in Sweden, where a complex massive sulfide ore is treated, is presented and discussed based on Boliden’s Garpenberg plant. The results showed an increase in the flotation recovery of fine valuable minerals. Zinc (Zn) production was increased by between 1,100 and 1,500 t/a, while salable yearly silver (Ag) production was increased by 1,500 kg. The copper (Cu) grade in the final concentrate was increased by 1 percent, while reductions in its Zn and lead (Pb) grades were obtained. Moreover, considerable reduction in Zn deportment to the final tail was observed

By Ping Zhang, Shahram Mozaffari, Andreas Ylmefors

The risk associated with mining induced seismicity and the related rock bursts has become one of the major threats to the safety and sustainability of mining at the Kiirunavaara mine. The causes of mining induced seismicity at the Kiirunavaara mine are very complex and have affected our understanding on the source mechanisms of seismicity and further the mitigation of the seismic risk. Detailed analysis of historical mining induced seismicity at the Kiirunavaara mine was conducted. The focus of this analysis was placed on the classification of large seismic events and the evaluation of the influential factors on the classified seismic events. 145 events with local magnitude larger than 1.5 that occurred between January 1, 2011 and March 31, 2021 were analyzed. For this analysis, seismic events located in the hanging wall were not included, as these have not been observed to cause large damages to the mine itself. It was found that the magnitude of the events had good correlation with the stress change in relation to the production location. The seismic events were classified as mining-front associated, ore-pass associated, mining-front and ore-pass associated and others, according to their hypocenter location. Most of the mining-front associated events, concentrated around the production levels and slightly above and below them, generally correlated with shear cracks, and most of them occurred when the ore flow between two production levels started. The numerical modelling showed that slip of the geological discontinuity, due to unclamping between hanging wall and footwall, could be the major causative mechanisms, which further supports this finding. The ore-pass associated events are located close to the ore passes. Large seismic events located between ore passes have the source mechanism of both fault-slip and non-shear, but events located at the outer side of ore passes were all fault-slip type. By checking with the ore pass scanning data, it was concluded that the most of the events located between ore passes could be pillar bursts. An elastic core concept has been then used to define a critical pillar width. The paper is not intended to be prescriptive but rather to initiate discussion of the possible classification of seismic events at the Kiirunavaara mine and to present new perspectives of the causes of the seismicity for improving the present seismic risk management.

Apr 26, 2022