Search Documents

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By R. M. Kakwani

The filtration and dewatering results of -32 mesh Pittsburgh seam coal are discussed with reference to the microscopic structure parameters, i.e., particle segregation in the cake and particle and pore size distributions at different layers. At low solid concentration of 0.33 kg coal/kg water, a non-uniform cake structure is observed in which the particle and pore sizes increase from the top to bottom layers in the filter cake. An increase in the solid concentration in slurry produces more uniform cake structure and higher filtration and dewatering rates. Air bubble entrapment in the coal filter cakes is also discussed.

Jan 1, 1984

By Z. Yunquan

The flocculation and dispersion behaviors of microsize wolframite and quartz are systematically studied in this paper. For synthetic mixtures, the floc separatory method on gravity units--electromagnetic vibration table (EVT) and lifting column (LC), have been approached. Satisfactory results can be obtained with a weak shearing. A better metallurgical performance can also be achieved for natural ore slimes through the combined technique. The efficiency is better than that of single gravity separation. Finally, the mechanism has been investigated.

Jan 1, 1990

By Kendall Y. Keuhey

The Mercur Mine, developed and operated by Getty Mining Company, is designed to process 3,000 tons/day of gold ore from the historical Mercur Hill mining district. The mill process involves crushing, grinding, and cyanide carbon in leach for recovery of gold ores ranging from 0.08 to 0.10 oz/ton. During the mining of normal grade ore, a substantial tonnage of material containing 0.02 to 0.05 oz/ton is mined and would be available for heap leaching. Also, Getty Mining is developing methods to test and prepare lower grade material for heap leaching by rejecting a course rock fraction from the grinding circuit SAG mill. This lower grade fraction is suitable for heap leaching, and its removal will upgrade the regular mill feed. Other test methods are directed toward leaching techniques on some 4.0 million tons of tailings that resulted from roasting and/or cyanide leaching Mercur ores in the early 1900s. The natural carbons associated with the Mercur deposits require special treatment to reduce their gold adsorption effects when leached with cyanide.

Jan 1, 1983

By Wayne Hilgedick

Peabody Coal Company is the nation's largest producer of coal and is headquartered in St. Louis, Missouri. In 1978 Peabody divisionalized its operations to establish more responsive and effective mine management. Peabody Coal Company's Arizona Division operates two large surface mines, the Black Mesa and Kayenta Mines. Both are located in northeastern Arizona, approximately 30 miles from Kayenta, Arizona, on the Navajo and Hopi Indian Reservations. The Black Mesa Mine produces 4 to 5 million tons of coal per year and the Kayenta Mine produces 7 to 8 million tons per year. Coal from the Black Mesa Mine is transported 274 miles by coal slurry pipeline to the Mohave Generating Plant located on the Nevada/Arizona border at Bullhead City, Arizona. This plant is jointly owned by Southern California Edison, the Los Angeles Department of Water and Power, Nevada Power Company and Salt River Project Agriculture Improvement and Power District.

Jan 1, 1983

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago, there were only a small number of projects that stretched beyond 100 kt/d (110,000 stpd) throughput rates. Today, and moving forward, virtually all the major copper projects are sized beyond this, with throughput rates up to 250 kt/d (275,000 stpd) now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 (5,650 cu ft) flotation cells, through to the 257 m3 (9,076 cu ft) cells and to the current 660 m3 (23,380 cu ft) machines. The contributions of specific copper concentrators to this growth phase are reviewed in this article. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 1, 2014

By J. O. Marsden, C. Green

In 2003, a high-temperature pressure leaching circuit to treat copper sulfide concentrates was commissioned at the copper/molybdenum operation at Bagdad, AZ. In late 2007, a medium-temperature pressure leaching circuit was commissioned at the Morenci mine in Arizona. The Morenci circuit was shut down in mid-2008, following a fire in the autoclave circuit. The onset of the global financial crisis in late 2008 resulted in significant changes to the operating profile in the Southwestern United States with respect to concentrates production, concentrates treatment, acid production and acid consumption. As a result of these changes, the Morenci concentrator was shut down, and the pressure leaching circuit remained offline. In late 2014, the increasing acid requirements in the Southwestern United States prompted a reevaluation of the Morenci concentrate leaching facilities. As a result, the pressure leaching circuit was restarted in high-temperature (200 °C) mode in May 2015 and has operated successfully for three years since recommissioning. This paper describes the current pressure leaching circuit configuration and the factors leading to the successful application of copper sulfide concentrate leaching at this location.

By LINDSAY BOTTOMER, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

A master composite (Master Comp) sample was prepared from three pegmatite zones from the Zoro Dyke D1 for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample that was crushed to approximately P80 = 600 μm. The sample consists of spodumene (10.5 percent), quartz (29.3 percent), plagioclase (29.0 percent), K-feldspars (21.3 percent), micas (5.1 percent), tourmaline (2.9 percent) and Fe-Mn-phosphates (0.1 percent). Liberation of spodumene (88 percent) and gangue minerals, including quartz (89 percent), feldspars (94 percent) and micas (83 percent), is very good at this P80 . The average lithium (Li) concentration is 3.7 percent in spodumene, 2,196 ppm in micas, 1,001 ppm in tourmaline and 115 ppm in K-feldspars. Spodumene accounts for 96 percent of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other Li carriers. The HLS was conducted on a subsample that was crushed to smaller than 6.4 mm, with the smaller than 600 µm fraction removed from this test. The HLS results indicate it is possible to produce a high-grade lithium concentrate, with close to 6 percent Li2O, after the rejection of iron silicates with magnetic separation.

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By M. Moats

Copper electrowinning operations have dramatically improved their ability to produce high quality copper at low costs over the past several decades. Even so, some fundamental knowledge is still lacking that could allow operations to run even more efficiently. For example, a rule of thumb exists that estimates a current efficiency loss of 2-3% per gram per liter of iron in the electrolyte. While several laboratory studies have been performed that demonstrate this rule of thumb is likely true, no definitive relationship exists. In this paper, the first steps in developing a definitive relationship are presented. The effective diffusivity of ferric ions in synthetic copper electrowinning solutions was measured using chronoamperometry and the Cottrell equation. The effective diffusivity of ferric ion was determined as a function of electrolyte concentration and temperature. Synthetic electrolytes were then used in laboratory-scaled copper electrowinning experiments, where relationships between current efficiency and solution composition were found to exist under stagnant conditions. Key words: Copper electrowinning, Current efficiency, Chronoamperometry, Ferric ions

Jan 1, 2009

By J. Chai, Y. Qiang, D. D. Zhang

"In order to control Quaternary loose layer settlement in East China, there are monitoring results based on the 3 water level observation holes and 7 sand layer of fiber Bragg grating (FBG) strain sensor. Un-der the conditions of upper group water injecting to lower group of loose layer, the deformation characteristics of upper, middle and lower group of loose sandy soil layer changing with time and relationship with the water level are studied. The constitutive relation of stress-strain is also studied at different sand layers. Research results show that using water injecting from upper group into lower group of loose layer can ease the loose layer compression deformation. With the water level dropped, in East China soil creep deformation occurred, which accord with viscoelasto plastic model. The deformation of lower sand group has clear later effect and no direct relationship with water level. The results provide an important basis for the study East China stratum settlement model and water management. INTRODUCTION Ground-surface subsidence is a common geological disaster, which has the features of continuous, changing slowly, concealment (Y.P. Yin et al. 2005). Today, due to underground mining and constructions in formation compression, surface subsidence is wide-spread in the world, which is the environmental geological problems in the worldwide that cannot be ignored (Y.Q. Xu et al. 2006, D.L Gallo-way et al. 2000, Qiu, B. et al. 2011). The eastern region of China has generally geological disasters in coal mine geological caused by the thick loose layer settlement like as mine shaft failure. Stratum dehydration consolidation is a major cause of loose layer settlement (H.Y .Liu et al. 2007). A method of water injection using ground water to stable water level is proposed, which can effectively control the loose layer caused by compression settlement(J. Chai et al. 2012&.2013). Accurately knowledge the characteristics of strata deformation is the premise of settlement management (Q.C. He et al. 2006). Previous re-search (J.F. Miu et al. 1996, X.Y. Gu et al.1998, Y. Zhang et al. 2006), mainly studies are focused condition of the city pumping irrigation, de-formation characteristics of middle and up loose layers. On a group of aquifer in East China, the loose layer losing water is caused by coal mining, bottom water drainage and overlying strata water flowing fractured zone hydrophobic induced by mining, which the dehydration conditions have great difference from one to another. The Position of water loss is centralized in bottom aquifer, and the formers of ground subsidence geological environment and settlement mechanism are different. According to the study of stratum settlement, usually the de-formation of sand layer is ignored(C.H. Liu et al. 2004), but few studies show that the sand layer have the plastic deformation, and contains the creep deformation, water content of sand soil may become the main settlement layer (Z.X. Wei, 2002, C.H. Liu et al. 2004)."

Jan 1, 2015

By Dale K. Nash

The authors have developed a com¬puter-assisted critical path planning and scheduling model to help reduce time required to move longwall mining units. The model includes time constraints and limited resource constraints, such as manpower, machinery, supplies, work space, and transportation routes. Outstanding results were achieved on the first move to which the computer-model pas applied; e.g., downtime due to the move was cut by 50%. The model and the schedules developed using it provide an excellent blueprint for future moves and have led to significant savings in time and costs for Emery Mining Corporation, Huntington, Utah.

Jan 1, 1983

By J. C. Harrison

When Exploraciones Eldorado, S.A. de C.V. finished their first phase of reverse circulation drilling at their La Trinidad property in Sinaloa, Mexico they began immediately with permitting and engineering activities. The first phase of drilling lasted four months and ended in April, 1994. The second phase of drilling ran from May through September of 1994. From May through December, 1994, Exploraciones Eldorado performed the permitting and engineering work for their La Trinidad heap leach mine. The mining permit was submitted to the regulatory agencies in February of 1995 and the first draft of the feasibility study finished one month later. The report outlines the permitting and engineering activities that took place during the second half of 1994.

Jan 1, 1996

By G. P. Brahmaprakash, K. A. Natarajan, N. Jyothi, K. N. Sudha

Some important electrochemical aspects involved in the bioleaching of mixed sulfides have been discussed with reference to selective sphalerite dissolution from different binary mineral combinations. Combination potentials and galvanic currents were measured in different binary combinations of sphalerite with other minerals such as galena, chalcopyrite and pyrite in order to under- stand the electrochemical dissolution behaviour of sphalerite when coupled with other minerals. The effect of applied DC potential was also studied with reference to selective sphalerite dissolution from a binary mineral mixture. An application of a potential of -500 mV (vs SCE) was found to enhance bacterial growth as well as selective sphalerite dissolution. Factors influencing bioleaching of sphalerite under a negative applied potential are discussed.

Jan 1, 1989

By W. J. Dolinar, S. P. Sandoval

The US Bureau of Mines (USBM) implemented the Fe2+/ Fe3+-SO2 anode reaction in a Cu-electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/ m2 (24 A/ft2) and 40°C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb), compared to conventional electrowinning. Acid milling 5was completely eliminated, and the SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1996

By R. Bhaskar

The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1985

By Manchao He, Xiaoding Xu, Yubing Gao

Based on the geological conditions of the 15,600 working face in Pingba Mine, this paper establishes the mechanical model of the stress distribution in the pre-working face under the influence of mining pressure based on a hemispherical stress distribution theory. The analytical formula for the stress distribution is determined. A numerical model for the mining pressure under the influence of key layer is also constructed, and dynamic stress interruptions under various roof-cutting relief schemes in different horizontal positions are simulated. The stress distribution of the stope under different pressure relief schemes is analyzed and compared with the theoretical results. Results show that blasting roof cutting blocks the transmission of the abutment pressure to the working surface to the coal and rock mass in front of the working face, reducing the significant working face mining pressure influence range, which decreases as blasting pressure relief position moves toward the working face. Stress accumulation in the coal in front of the working face also increases as the blasting pressure relief position moves toward the working surface. Engineering practice results show that blasting cutting can effectively block the propagation of mining pressure, and the stress impact range is shortened by approximately 1/3.

Jul 31, 2021

By V. R. Degner

The trend in both the metallic and non-metallic mining industry is toward processing increasing y higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This paper reviews the R&D approach used in translating smaller flotation machine experience to establish the configuration of a 1000 cu ft (2B.3 cu m) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1978

By A. N. Islam, C. Simons, M. N. Hughes, J. Barrett

The effluent from the bio-oxidation of arsenopyrite contains high concentrations of iron(III) and arsenic(V), the pH being in the range 1.0-1.3. The use of lime to increase the pH causes the precipitation of calcium sulfate, calcium arsenate and a mixture of solids containing calcium, iron and arsenic. The presence of calcium is due to slaked lime encapsulated by the iron arsenate precipitates. These iron arsenate solids are related to known minerals. The use of sodium hydroxide to effect the precipitation of iron and arsenic produces solids which are more stable than those produce by using slaked lime. The use of limewater produces an initial precipitate of calcium arsenate.

Jan 1, 1991