Search Documents

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semigelatin dynamites, three slurry explosives and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): NO, 0.010-0.035; NO2, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1979

By C. L. Elmore

This paper describes a new development in the cyanidation of gold ores, which we expect will result in a major improvement in the way many gold ores are treated. The process has evolved through work at Hazen Research, Inc. for Kamyr, Inc. and in brief, the consists of utilizing oxygen rather than air in the carbon-in-1 each (CIL) process. We refer to this improved process for all ores amenable to cyanide leaching as carbon-in-1each with oxygen or CILO.

Jan 1, 1988

By Richard E. Beane

For several decades, the minerals industry has used leaching techniques to extract metals from rocks whose grade was too low to be treated profitably using conventional metallurgical techniques, and, as of 1972, about 15% of domestic copper production was derived using leaching methods (Beall 1). Increasing interest is currently being directed toward solution mining, particularly with respect to copper, for basically two reasons. In the first place, geological exploration has outlined several copper deposits of large tonnage and 1m', grade which are buried at sufficient depth to preclude open-pit mining which would make such mineral deposits ore deposits. Nevertheless, these occurrences provide significant potential if they could be treated by chemical leaching in situ. Secondly, the porphyry deposits of the western united States, which provide by far the largest percentage of domestic copper, do not terminate geometrically with sharp borders. These large disseminated bodies commonly decrease in grade laterally away from volumes of rock containing ore grade metallization, and the distinction between ore and waste is strictly economic. In order to extract ore grade material from the ground, a significant amount of rock containing sub-ore-grade copper must also be removed which, when placed on dumps, is amenable to solution mining. These two considerations clearly indicate the reasons for the growing interest in solution , leaching techniques--namely the ability to exploit deeply buried low grade deposits and the expansion of reserves in deposits currently under production.

Jan 1, 1977

By J. Christophe Niyonzima, Ekata Emmanuel Edo, Sayaf Mustafa, Liqun Luo

Iron and manganese both are important ferrous metals, and they usually need to be extracted separately for better usage. Ferromanganese ore from the Yunnan Province of China was investigated by subjecting it to reduction roasting, leaching, magnetic separation, hydrometallurgical separation process, X-ray diffraction (XRD), electron probe micro-analysis (EPMA) and scanning electron microscopy/energy-dispersive spectroscopy (SEM-EDS). It is noted that the ferromanganese ore contains valuable components or elements of 21.41 wt%Fe2O3 and 19.88 wt%MnO, which are 14.99% and 15.40% of the total of Fe and Mn, respectively, with a large amount of impurities comprising 33.00 wt% SiO2, 9.81%wt%Al2O3, etc. After roasting, microscopic examination showed the presence of haematite, magnetite, pyrolusite, psilomelane, hollandite, marcasite, pyrite, limonite, braunite and manganite, while XRD analysis showed that the magnetite content increases with the increase in roasting temperature, reflecting the increase in conversion of haematite to magnetite. Based on EPMAand SEM-EDS analysis, it was shown that the haematite and magnetite interface were the main Fe-bearing minerals; however, the dissemination of the two minerals, that is, haematite andmagnetite with the coexistence of Fe- and Mn-bearing minerals, will result in difficulty in effective separation of Fe and Mn. The effective roasting temperature and roasting time were 800 °C and 60 min, respectively, to avoid the formation of a composite oxide of MnxFe3-xO4 beyond 800 °C. The Fe recovery via roasting and magnetic separation only was 66.56%, whereas a combination of magnetic separation which ensued after the leaching process showed a recovery of 80.08% and 59.95% of Fe and Mn, respectively.

Mar 26, 2021

By R. B. Toombs

In describing the Canadian mineral industry in a world setting, this paper examines the industry from four points of view. First, mineral industry growth is related to trends in economic activity thereby providing a measure of the industry's importance in the Canadian economy. To give perspective to the Canadian scene, reference is made to economic trends in several of the world's leading mineral producing and mineral consuming countries. The Canadian mineral industry is next examined in terms of its major developments of the past 20 years and the resultant size, structure, and production diversity of 1964. The position of the Canadian mineral industry in the world industry is then analyzed by tracing changes in mineral supply and demand patterns. Growth of the Canadian industry depends greatly on expansion of export markets because three fifths of the value of production is accounted for by exports. Finally, attention is directed to the outlook for the Canadian mineral industry. Problems facing the industry are surveyed, and an appraisal is made of economic policies that have encouraged industry growth. A forecast of mineral production value in 1970 is included.

Jan 1, 1964

By Qingming Feng, Jinhong Zhang

A study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature, and curing time significantly affect the mechanical property of geopolymermatrix. Through optimization, an above-100MPa compressive strength has been achieved with the geopolymerization products. The optimum working conditions involves 10MNaOH concentration, 14–15% water content, and curing at 90 °C in an oven for 1 day or at ambient condition for 3 weeks. Adding Ca(OH)2 does not help to increase the compressive strength of the specimen.Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength, even after a 1-month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS (scanning electron microscopy and energy-dispersive X-ray spectroscopy), XRD (X-ray diffraction) and ATR-FTIR (attenuated total reflectance Fourier transform infrared) are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method for applying fly ash as a high-strength water-resistant precast construction material.

Aug 17, 2020

By Perry M. Jones

An important operational and environ-mental concern associated with in situ leaching activity is the balance between solution injection and recovery. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. The Bureau of Mines is investigating the factors that affect solution balance in an unsaturated ore deposit, as part of ongoing in situ leaching hydrologic investigations at the Cyprus Casa Grande Mine. Flow conditions in 58 injection and recovery wells at the Casa Grande In Situ Leaching Test Facility were monitored daily over an 18 month period. Changes in the balance between injection and recovery occurring during this period were evaluated using analytical and statistical methods. The results permit estimation of solution distribution and the volume of solution stored in microfractures and interstitial pore spaces within the deposit following 18 months of leaching. Approximately half of the difference between well injection and well recovery can be accounted for by solution movement through macrofractures into nearby drifts. Estimates of solution storage within the ore deposit at the end of 18 months of leaching range from 3.5 to 6.9 pet. of injected solution. These results also suggest that 13 to 26 pet. of the fracture/interstitial pore space in the deposit was saturated with solution after 18 months of leaching.

Jan 1, 1991

By N. Moelans, I. Bellemans, K. Verbeken

Metallic droplets can remain attached to solid particles within liquid slags, resulting in production losses in several movement of solid particles in the liquid slag in a system, considering the attachment of liquid metal droplets to solid slag and on the resulting microstructures is investigated as a function of the velocity of the particles. For all wetting For the amount of metal attached to the particle, a clear trade-off was found between the speed of motion of the solid particle and the wetting regime.

By Yuanbo Zhang, Yikang Tu, Zijian Su

Stainless steel swarf is a typical by-product produced from stainless steel processing, which contains a significant level of valuable metals, such as iron, chrome, and nickel. About 1 million tons of stainless steel swarf are generated in China annually, but as mixed with impurities such as Al and Si, stainless steel swarf is not suitable to be directly smelted into stainless steel through refining process. In this study, stainless steel swarf was applied as a strengthening agent during limonitic laterite sintering process. The effects of adding stainless steel swarf on green bed permeability, the yield and quality indexes of the sinters, and the microstructure of the sinters were evaluated systematically. The results showed that the concentrated distribution degree of granules and green bed permeability were improved after adding stainless steel swarf. As the additional amount of stainless steel swarf increased from 0 to 3%, the tumble index and yield of the sinters rose from 50.07 to 54.69% and from 62.04 to 67.35%, respectively. The addition of stainless steel swarf would not change the phase compositions, and had little adverse impact on the metallurgical properties of the limonitic laterite sinters.

Aug 23, 2023

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By D J. Bradshaw

It is well known that the chemical environment determines the success of the flotation process, however its characterization and control is difficult to achieve. This work evaluates the use of various measurements, including mineral potential measurements, in gaining an understanding of the influence of varying parameters such as the milling media and the reagent suite composition on the flotation performance of a platinum group metal (PGM) bearing ore. The results showed differences in the response of the various mineral electrodes to the different conditions, however the changes in flotation performance of the different minerals in the ore could not be wholly described by the electrochemical changes, demonstrating the limitations of these measurements.

Jan 1, 1999

By Joe Hachey, Jerry Dorn, Jeff Schutt, Derek Penrice

"Sound Transit’s East Link Project, a $3.7 billion (2015 $), 14-mile light rail extension, will connect downtown Seattle with the rapidly developing east side cities of Bellevue and Redmond. Among the most technically challenging aspects of the Project is the 2,435 foot long Downtown Bellevue Tunnel (DBT), which will be constructed through the central core of Bellevue underneath 110th Avenue NE using a combination of Sequential Excavation Methods (SEM) and cut and cover tunneling. The 1,980 foot long central SEM component of the DBT will be mined at shallow depth through challenging and complex geology, comprised of glacially overconsolidated soils, containing both regional and perched groundwater conditions and in close proximity to existing high rise buildings. The paper shares lessons learned from the planning decisions and risk based approach to the investigation, design and procurement processes which shaped the DBT configuration and enabled a successful transition to the project’s construction stage. INTRODUCTION The East Link Project is a voter-approved $3.7 billion (2015 $), 14-mile extension of the existing Sound Transit (ST) light rail transit (LRT) system from downtown Seattle, across Lake Washington via I-90, to the cities of Bellevue and Redmond on the east side of Lake Washington. With targeted completion in 2023, East Link will provide riders with an efficient and reliable connection between the largest population and employment centers on the east side and downtown Seattle. The project alignment is indicated in Figure 1 below.ST completed the Preliminary Engineering (PE) phase of the East Link project in late 2011. Subsequently the final design contract for the easternmost seven miles of the project was awarded to the H-J-H Team, a joint venture comprised of HNTB, Jacobs Engineering and Hatch Mott MacDonald in February 2012. H-J-H’s final design scope includes approximately 7 miles of double-track LRT between the east end of the I-90 East Channel Bridge and the Overlake Transit Center Station. While the project scope is extensive and diverse, the focus of this paper is the DBT. The DBT is located immediately north of the East Main Station, and travels approximately one half mile through downtown Bellevue under 110th Avenue NE between Main Street and NE 6th Street; terminating at the Downtown Bellevue Transit Center (BTC) Station. The location and extent of the DBT is indicated in Figure 2."

Jan 1, 2016

By S. Saeb, C. Francke

Introduction Although mining in one form or another has existed for millennia, the use of numerical methods for mine design is a relatively recent development. The basic physics that control the behavior of rock or soil have been known for centuries, but it wasn’t until the last half of the twentieth century that analytical methods that could accurately predict the behavior of a large, irregular rock mass were developed. Before the advent of modern computers combined with differential and integral analytical methods, numerical methods available to mining engineers were limited to closed form solutions for simple excavation geometries. Today, mine-scale three-dimensional stress analyses can be performed on a relatively inexpensive personal computer. Many of the recent advances in rock mechanics modeling are the result of research funded as part of nuclear waste repositories around the world. The large scale exacting performance requirements of waste repositories are frequently very different from traditional rock mechanics projects. These facilities are designed and built under tighter control and scrutiny because of the potential hazards they present to the public. Therefore, a great deal of research towards advancing rock mechanics and numerical modeling resulted from these projects. Much of the repository research is applicable to commercial mines. The advances in modeling programs have been paralleled by advances in computer equipment. Today, a moderately equipped personal computer can handle most mine geomechanical modeling projects in a reasonable period of time. While the learning curve varies, an engineer with modeling experience can develop a medium sized model in a few days. The relatively low investment cost of geomechanical modeling today makes it accessible to most mining operations. The benefits of a solid geomechanical modeling program include reduced operating costs, improved safety, and reduced design costs.

Jan 1, 2007

By Lancelot E. Kun

The high-rate floc blanket clarification process developed by the Anglo American Corporation of South Africa is capable of continuously clarifying gold and uranium pregnant solutions containing 200-2500 mg/L suspended solids to below 25 mg/L solids at an average rising velocity of 8 m/h at the low process cost of R0,001-0,002 per ton of liquid treated. Overall process cost savings are mainly due to increased polishing filtration cycle times.

Jan 1, 1984

By Charles H. McGuirk

The Port of Conneaut, the largest bulk material handling and storage facility on the Great Lakes, is using the latest electronic and visual testing devices to augment and enhance its well established computerized preventive maintenance system. The results of this comprehensive program have been impressive. The remaining life of components can be accurately forcast, and replacement can be programmed around operations, resulting in a significant improvement in system availability and reduced costs for the dock operator and its customers.

Jan 1, 1983

By G. J. Goldberg

Through the early 1980's, surveying at Bingham Canyon required a great deal of repetitive and manual work. The advent of total station surveying equipment provided an opportunity to improve the speed and accuracy of surveying work while reducing manpower needs. An evaluation of total station systems and their ability to meet the surveying requirements of Bingham Canyon culminated in the purchase of a total station system as the mine re-opened in 1986. This paper presents the procedure for evaluating, implementing and using the total station survey system at Bingham Canyon.

Jan 1, 1990

By Jie Zhang, Xi Zhang, Yu Wang, Wei Zhao

The study proposes a novel reagent scheme where adding a small amount of citric acid (CA) significantly improves the depression effect of sodium silicate on calcite and fluorite. The flotation results suggest optimal concentrations for CA and sodium silicate, achieving nearly complete depression of the minerals. Theoretical analysis indicates that CA dissolves calcium ions on the mineral surface, enhancing the adsorption of sodium silicate and preventing collector adsorption.

Mar 27, 2022

By H. C. Lautenschlaeger

Let's start with a bit of History. Before the advent of woven wire screen cloth or perforated plate as we know it today, screens or sieves, as they were called, were probably made by the Greeks or Romans around the year 150 B.C. Coarse openings were made from bamboo or other woven reeds or with holes punched in leather hides, while fine openings may have been made using hair from the long tails of horses woven with small openings. The first metallic woven wire screens were probably produced by the Germans in the 15th Century. All of these screening devices were, of course, hand operated. The first records of mechanically driven shaking screens are found in "John Smeathon's Diary of His Journey to the Low-Country" in 1775. He was the English Civil Engineer who built the famous Eddystone Light House and discovered the formula for making hydraulic cements. He described a screen the Dutch were using as a wooden frame on which woven wire was mounted. This box was inclined at an angle and hinged on the lower end. The upper or feed end was equipped with a pulley so they could raise it up, say 5" or 6", and then let it drop abruptly onto a sill or stop plate, thus jarring the material deposited on the woven wire through the openings. Material that was passed over the deck was scooped up and redeposited on the woven wire for rescreening. This was an early form of what is today known as a recirculating load.

Jan 1, 1983

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Laramide porphyry copper deposits are large, low grade (<0.8% Cu) deposits that contain disseminated copper minerals, breccias, and stockwork veinlets of copper and molybdenum sulfides associated with porphyritic intrusions in Southwestern New Mexico. Critical minerals, such as PGEs, tellurium, indium, germanium, and gallium are recovered from the anode slimes remaining after copper is refined. Detailed age dating, mineralogy, geochemistry, along with geologic mapping could refine the location of critical minerals within specific systems and could identify porphyry systems with elevated critical minerals that could become economic, in addition to the already produced copper, gold and molybdenum.

Feb 1, 2023