Search Documents

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By Landy Stinnett

"When performing a valuation of a mineral property, a developing mine or perhaps an ongoing operation, the appraiser is typically provided with a range of information prepared by the property owner. This information can include ownership records, geological interpretation, assay data, an estimate of the reserves or resources believed to be on site (tons and grade), mine plans, production forecasts, capital and operating cost projections, and so forth.The appraiser familiarizes himself with the data, analyzes the various reports and then prepares the appraisal. There is usually a site visit, and there may be some effort at comparison of the particular mineral deposit with others in the region or with those of similar depositional characteristics, but for the most part, the appraiser is relying on the corporate documents, tempered by his/her experience in the field. Time is usually of the essence, the cost for the assignment has been trimmed, and therefore independent verification of the various components comprising the underlying data base (legal review, redrilling portions of the deposit, collection of new samples, re-assaying, etc.) is unlikely in most situations.In the case of high-value commodities — gold, silver, diamonds, perhaps the platinum-group elements — there have been numerous examples of the property owners attempting to increase the value of their holdings by nefarious methods. Most of these involve salting the deposit in some fashion; i.e., introducing small amounts of the commodity into samples being sent to a laboratory for analysis so that the resultant assay shows a higher grade (Donaldson, 2002; Greeley, 2001; Lechler et al., 2008 and Meech, 2001). Other schemes to enhance the apparent worth of a property include the use of nonstandard assay procedures, incorrect handling or withholding of the underlying information, and false reporting."

Sep 1, 2016

By Danqing Gao, Brijes Mishra

Spatial variance of rock properties is an important characteristic of rock which addresses the heterogeneity of mechanical and physical properties and their effect on underground mining. Assessing spatial variance can be useful for both locating potential difficult grounds and performing reliability analysis in the mining support system. This study shows a microscale numerical model for rock material based on continuum mechanics. To consider the spatial correlation factor of mechanical properties in realistic rock mass, this study introduces a spatial correlation concept into the traditional type III extreme value distribution model. Based on the improved microscale random model, we conducted a series of numerical uniaxial compressive tests and one longwall mine model to investigate the progressive failure of rock. The results show that spatial correlation factor can significantly affect the load-deformation curves and fracture patterns. The spatial variance model was applied to a longwall mine that included several cutting sequences to observe the influence of the spatial variance on roof behavior. The cohesion and friction random fields induced failure that propagated randomly through the immediate roof in different entries. The results showed that the spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Jul 20, 2020

By J. F. Burr, D. Snyder, W. Calder

"INTRODUCTION “Explosion protection” refers to techniques used to minimize the potential for electrical and electronic equipment to create an ignition while operating in a hazardous location (HAZLOC). In particular, U.S. coal mines are required to use equipment in certain areas of the mine that has been approved by the Mine Safety and Health Administration (MSHA) for use in a methane and coal dust environment to limit the risk of the equipment creating an ignition-capable spark or a thermal energy ignition. In general, MSHA’s regulations for explosion protection recognize two techniques: the use of explosion-proof enclosures (XP boxes) and 2-fault intrinsic safety for electrical and electronic equipment. For 2-fault intrinsically safe (IS) equipment, the U.S. mining industry requirements are unique in that the equipment is certified by MSHA. The criteria MSHA uses to evaluate equipment for intrinsic safety, as required by Title 30 of the Code of Federal Regulations (30 CFR) [30 CFR, Sections18.20(b), 18.68(a)(1), 19.1(b), 20.1(c)(2), 22.6, 23.6, and 27.20(a)], is published in a document referred to as ACRI2001 (1). Outside of U.S. underground mining, many industries and countries accept equipment that is designed to a consensus-based international standard (ANSI/ISA 60079-11 is the U.S. version). The purpose of this study is to provide an overall assessment of the ANSI/ISA 60079-11 standard on 2-fault intrinsic safety and the MSHA ACRI2001 acceptance criteria, and determine if the ANSI/ISA document can be an alternative to ACRI2001 while maintaining an equivalent or better level of safety for miners. There are many drivers for this study. First, immediately after the 2006 MINER Act (2) was passed, there was a perception in the industry that the unique MSHA requirements were contributing to delays or restricting the availability of equipment to meet the requirements of the Act. Additionally, the MINER Act required that mine operators submit an accident response plan for MSHA approval, to be reviewed every six months. MSHA is required to determine if these plans reflect the most recent credible scientific research and make use of currently commercially available technology. There is a concern, as expressed in a recent National Academy of Science (NAS) study (3), that the unique requirements for U.S. mining may be limiting the technologies available to coal miners and technology options for mine operators. Accordingly, the study recommended that the National Institute for Occupational Safety and Health (NIOSH) and MSHA re-examine their technology approval and certification processes to ensure they are not deterring innovation, and explore opportunities to cooperate with other international approval organizations to harmonize U.S. and international standards without compromising safety. Lastly, the National Technology Transfer Act (NTTA) and the accompanying Office of Management and Budget’s OMB-119 circular mandate the use of consensus-based standards by federal agencies. However, for U.S. mining operations, MSHA cannot accept such standards unless a determination is made that such standards provide an equivalent level of protection for the miner, per the requirements of the 1977 Mine Act, the 2006 MINER Act, and 30 CFR Part 18 regulations."

Jan 1, 2017

By R. R. Sacrison

The Barrick Mercur Gold Mine lies in the Oquirrh Mountains of northern Utah. Limestone, sandstone, shale, and chert are the predominant rock types being mined. Recent expansion has encountered rhyolite. Lithology and structural attitudes control most mechanical behavior. Slope steepening, mine planning, and site selection are presented as means by which geological engineering has contributed to the economics of the operation. Geomechanics investments of approximately $700,000 have resulted in cost savings or additional production worth over $16,000,000.

Jan 1, 1990

By S. G. Britton

Thin seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges are increased depending upon the presence of various external factors such as labor unions, Federal and state regulations, and market characteristics. This paper explores the turn-around situation occurring at Tanoma Mining Company (TMC), a medium-sized underground coal mining company in central Pennsylvania, USA. Using a systematic approach of improving management controls and direction, labor relations, and communications, coupled with an intensive upgrade/rebuild/replacement program for equipment and systems used at the mine, TMC has begun reversing its' cashflow position from negative to positive within two years.

Jan 1, 1991

By Kumara S. Rachamalla

Long-term stability, appropriate taxation and incentive policies are essential to attract and stimulate investment in the mineral sector. An outline of Ontario's $4.6 billion industry and associated tax incentives is presented. Producers are offered incentives under The Mining Tax Act, federal and provincial income tax acts for exploration and development by reducing Me after tax cost to 13-25¢ for each dollar spent. The Mining Tax Act provides generous processing incentives which have positive effects in enhancing investment and economic advantages of building processing facilities. Non-mining companies and entrepreneurial individuals can receive 25% of eligible exploration expenditures in grants/tax credits under the Ontario Mineral Exploration Program.

Jan 1, 1982

By M. R. Carter

The Rochester Mining District is located some twenty-five miles NE of Lovelock, Nevada. The District was discovered and named in the 1860's by prospectors from Rochester, New York. For a number of years, they worked Rochester Canyon, sinking shafts and inclines and making open cuts. After reaching a depth of approximately eighty feet, the miners tapped an underground channel and were driven from these workings by a strong flow of water leaving pumps in the shaft and barely escaping with their lives. With the Rochester workings no longer accessible, the miners went to the southeast and established the Relief Mining District. About 1881, gold was found in the gravel at the mouth of American Canyon, to the east of Rochester. These placers were worked until 1895, first by the Americans who reportedly took out $1 000 000, and later by the Chinese who mined the gravel with great skill. It was estimated that the Chinese took out as much as $10 000 000.

Jan 1, 1987

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By N. W. Stump

New developments in on-stream analysis using immersed radioisotope gauges including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding which is based on maximum throughput at constant product size and preliminary work in flotation control are also outlined.

Jan 1, 1974

By D. Kumar, R. J. Sweigard, J. Silva

The Forestry Reclamation Approach (FRA) recommends that the upper 1.22 m (4 ft) of spoil material on reclaimed surfaces should be left as uncompacted as possible to facilitate efficient tree root growth. However, the main concerns about applying the FRA to steep slopes is that the upper 1.22 m (4 ft) of loose spoil material could cause instability. Successful application of the FRA on the flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine site are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor any type of slope movement. Quarterly surveying of the monuments were done to quantify slope movement, either horizontally or vertically. The methodology developed in this research for field slope movement monitoring was validated using computer model results. Analytical models based on the limit equilibrium method (LEM) and numerical models based on the finite element method (FEM) were developed for slope stability analysis. The LEM analysis was done using the Geo-Slope/W program following the simplified Bishop method. However, numerical models were developed using the PLAXIS computer program following the Mohr’s Coulomb failure criterion and strength reduction technique. The slope stability analysis was performed for two different scenarios: first with the top 1.22 m (4 ft) of loose graded spoil material and second without top loose graded spoil material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems, due to 1.22 m (4 ft) loose graded spoil that would not exist otherwise for overly steepened slopes.

Jan 1, 2013

By Y. Luo

"It is generally known that spontaneous combustion potential is a function of coal rank, with low-rank coals having high susceptibility to self-ignition and high-rank coals having low potential. To establish this functional relationship and use it as an engineering tool to identify the propensity of coal to self-heat, both rank and spontaneous combustion potential should be quantified. ASTM D388 is normally used to classify coals by rank, but this classification system can only serve a qualitative analysis. To classify coals by their potential for spontaneous combustion, the self-heating temperature (SHT) method originally developed by the U.S. Bureau of Mines (USBM) was used by Litton and Page (1994) to correlate coal rank with spontaneous combustion potential. In that method, the SHTs of coal determined by an adiabatic experiment are linked with proximate analysis results through a proposed concept known as the “moist fuel ratio.” This ratio is a function of moisture, volatile matter and fixed carbon, all of which have widely different content percentages in different ranks of coal and have strong relationships with coal rank. However, the method is highly empirical, and there is large standard deviation between experimental data and calculated results. The equation correlating the coal quality parameters to determine SHT should be improved with more experimental data.This paper reports on the development of a new system for predicting the spontaneous combustion potential of U.S. coals, based on coal composition data from the U.S. Geological Survey’s coal quality database. First, the user is provided with a quantified classification of coal rank. Second, based on experimental SHT data covering a wide range of ranks from lignite to low-volatile bituminous coal, the original USBM correlation for predicting SHT is improved for the respective rank of coal. The relationship between the rank and SHT of U.S. coals was developed and plotted. The plot diagram can be used for a quick estimate of the SHT of a U.S. coal and as a cost-effective tool for the initial risk assessment of a new mine development."

Jan 1, 2015

By A. Bieg, M. Samson, Z. Bell, A. Zinsser, J. Schuyler

As the world progresses toward the renewable energy transition, the demand for minerals increases exponentially. According to the International Energy Agency (IEA) 2021 Net Zero by 2050 Report, critical mineral production needs to grow six times to combat climate change. It’s estimated that four to seven percent of global greenhouse gas (GHG) emissions come from the mining sector’s Scope 1 and 2 (direct and indirect) emissions. Including Scope 3 (upstream, downstream, and embedded) emissions, the sector accounts for 28% of global GHG emissions. In a typical mining operation, diesel fuel is the biggest source of direct GHG emissions, and haulage is often the main source of diesel emissions. Large haul trucks have been the industry standard for over 50 years and offer flexibility, relatively low capital cost (especially with equipment lease options), and guaranteed technology with known maintenance. The challenge will be to justify their continued use when there are more economical options that lead to significant reductions in GHG emissions. The purpose of this study is to compare five haulage options in terms of GHG emissions, using the methodology defined by the Greenhouse Gas Protocol Scopes 1, 2, and 3 (Category 2). Additionally, this analysis compares operating and capital costs associated with the five haulage options (emerging and proven technologies): 1) Diesel-Electric Haul Trucks, 2) Battery-Electric Haul Trucks, 3) Fuel Cell Haul Trucks, 4) Railveyor, and 5) Conveyor. This analysis looks at the emissions and costs associated with operating the equipment (fuel and electricity), the embedded emissions and costs associated with the construction and installation of the equipment itself, and the associated infrastructure (roads, powerlines, and rail).

Feb 1, 2023

By I. Weir-Jones

I. Introduction The experimental work described in this paper was carried out during 1967 and 1968 in an inclined reinforced concrete adit which had been driven during 1965 and 1966 to provide primary access for a new gypsum mine. The new mine was situated near the village of Sherburn-in-Elmet in central Yorkshire in an area of extensive post-glacial plains of deltaic and lacustrine origin. These plains cover a large area of this part of Yorkshire extending inland from the coast for a distance of about 35 miles. The gypsum deposit at Sherburn dates from Permian times and it is considered" to have been associated with the western-most edges of the ancient Zechstein Sea which was also responsible for the formation of the extensive evaporite deposits in north-east Yorkshire. The gypsum deposit, which varies in thickness from 10 to 15 feet, is extremely pure and it occurs quite close to the surface; in the Sherburn area the overburden is only 120 feet thick. The proximity of the deposit to the surface, however, tends to give a somewhat false idea of the magnitude of the problems associated with its extraction. These problems were all related to the nature of the overlying strata. As has already been mentioned, the surface deposits are post-glacial and they consist of an extremely large number of thin layers of varved clays, fine silts and sands extending down to a depth of 75 feet. From the bottom of the post-glacial deposits to the seam, a distance of about 45 feet, the strata consists of a succession of marls, weak sandstones, and siltstones, which although they are inherently incompetent materials, are appreciably stronger

Jan 1, 1971

By K. C. Kocsis

Underground ventilation systems, which require electricity to operate the fans and fossil fuel for heating in winter, can account for a significant portion of the energy consumption of mines. Recent studies have shown that the ventilation system in deep and highly mechanized metal mines could be responsible for 40 to 60 percent of their overall energy consumption. Presently, underground ventilation systems are designed for peak air volume requirements, which usually occur well into a future stage of the mines’ operating life. As a result, during their early operating stages, the intake air volume of the mines could be well in excess of their true air volume needs. Such ventilation systems could be considered as uneconomic, and to remain competitive the ventilation design needs to improve while the mines are trying to reduce energy consumption and their carbon footprints. This paper introduces a new mine ventilation design method where an underground base-metal mine’s ventilation system is designed by integrating discrete-event mining process simulation (DES) with mine ventilation modeling techniques. Furthermore, based upon the output data generated by means of discrete-event mining process simulations, the air volume requirement for the operating life of the mine is determined for “traditional” versus “activity-based” ventilation requirements. The output data generated through ventilation simulations are then used to quantify the economic and environmental benefits of an activity-based ventilation delivery system.

Jan 1, 2018

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By Nikhil Dhawan, Amit Barnwal

The present study reports a processing route to recover metals from integrated circuits of discarded random access memory (RAM) units containing ~ 66% printed circuit boards and ~ 33% integrated circuits. The integrated circuits are manually separated, grounded, classified, and subjected to water fluidization for the effective separation of metals. The significant separation was achieved via water fluidization, and the underflow fraction was magnetically separated. The magnetic fraction was thermally exposed in a muffle furnace, and the process optimization was carried out using a Box-Behnken statistical design. The detailed characterization at subsequent steps significantly aids the understanding of metal-plastic separation and enrichment. A concentrate containing 97% metals (Fe-59%, Ni-9.5%, Cu-7.7%, Sn-13.4%, Pb-5.6%, Ag-1.6%) with 96 wt% recovery can be recovered from discarded IC units. The process pursued is simple, adaptable, and environment-friendly, and the product can be used in conventional smelters.

Jun 23, 2020

By G. I. Mathieu

Research and development studies were carried out at the Canada Centre for Mineral and Energy Technology to produce a synthetic forsterite sand from asbestos tailings for Les Sables Olimag Inc. The National Research Council of Canada also supported and collaborated to the project. Theoretically, the technological approach consists of a heat at over 1300°C; however, the process without additive would result in the production of an enstatite-rich product (MgSiO3) having a fusion temperature less than 1600°C. The purpose was to foster the formation of forsterite (Mg2SiO4), a more refractory compound. The fabrication of the forsterite product requires pre-agglomeration of serpentine-MgO with a binder, which is stable at high temperature, to prevent the loss of the powdered magnesium oxide as dust in the kiln off gases and to maintain the mixture homogeneous during the process. Characterization of the end products with respect to mineral composition and thermal resistance are described. The synthetic forsterite in sand form was tested with success under a bath of liquid steel maintained at 1700°C for up to two hours. The advantages of the new sand and its potential applications will be reviewed.

Jan 1, 1992

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, there are all of the following rock types: oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently; overblasting wasted drilling time, and explosives caused excessive throw. Several possible methods for improving the blast design were considered and a geophysical method was chosen for testing. There had been reports in the journals that seismic methods were being used in Europe as aids for blasting design. A literature search turned up work by Haxby 1/ on use of a refraction seismograph for measuring pit bench rock strength. Using his work as a springboard, equipment was purchased and a program was planned and carried out for developing, evaluating and implementing the seismic method for routine mine use. Following are discussions of the development program and results.

Jan 1, 1974

By Evan J. Owen, Virginia T. McLemore

Rare earth elements (REE) and critical minerals are increasingly becoming more important in our technological society and are used in many of our electronic devices (such as cell phones, computer monitors, wind turbines, etc.), batteries, and magnets. Measuring REE and critical minerals in ashed coal approximates the REE and critical minerals in the fly or bottom ash remaining after coal is burned at a power plant, where REE and other critical minerals could be leached. In New Mexico, there are 26 coal fields in Late Cretaceous rocks in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, Rare Earth, and Critical Minerals) program. Higher concentrations of REE (as much as 2103 ppm total REE) are found locally in ashed coals from the basins. More chemical and mineralogical analyses are required to fully understand the distribution and origin of REE in these deposits. As the demand for REE increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics, perhaps even from coal.

Feb 1, 2025