Search Documents

By M. SIDDARAJU, Rameshwar Sah, Satendra Kumar, Arvind Jaiswal

The study explores a novel process to sinter porous iron ore with improved productivity and quality. The iron ore is pre-processed with calcined lime to temporarily close pores, preventing water absorption during granulation. This enhances reaction kinetics and early slag formation during sintering, resulting in significant improvements in sinter productivity, product yield, and cold strength property.

Feb 28, 2022

By J. D. Miller

Fluid flow phenomena and therefore the flotation efficiency of air-sparged hydrocyclone (ASH) flotation are strongly dependent on the operating and design variables such as air flow rate, slurry flow rate, underflow and overflow opening areas, percent solids in the feed, reagent levels, particle size, ASH length, etc. Time-averaged multiphase flow characteristics, as deter-mined by x-ray CT and described in a previous publication, are used to understand and explain the steady-state ASH flotation of quartz. A detailed parametric study of quartz flotation by a nominal 2-inch diameter air-sparged hydrocyclone (ASH-2C) revealed the influence of these variables on the flotation response which is discussed in terms of the multiphase flow characteristics. Thus, a phenomenological description of quartz flotation has been established to assist in the further development and utilization of the ASH technology.

Jan 1, 1995

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

By Yang Song, Li Shaokang, Wang Zhiqiang, Wang Jinjun, Li Guofeng, Su Meixuan

CaCO3, as a component widely existing in natural minerals, is a common impurity. In recent years, triboelectric separation has been applied to the separation of minerals containing CaCO3. However, the CaCO3’ s tribocharging mechanism is still unclear and the charging effect of CaCO3 is not obvious. In order to study the effect of triboelectric charging of CaCO3 particles under different conditions, according to the single particle frictional collision charge-mass ratio formula derived from the condenser model, an experimental platform for particle tribocharging was built in this paper. Then, the formula of charge-to-mass ratio (Q/m) was derived based on the analysis of the particle force. Particle image velocimetry (PIV) was used to record particle motion trajectories to calculate the Q/m of one particle by this formula. In the experiment, the airflow velocity, tribocharge material, and moving distance of the particles were varied to investigate the variation of the particle charge-mass ratio results. The results show that CaCO3 was negatively charged when tribocharging with mental. The particle’s Q/m is positively correlated with the airspeed. When the metal is triboelectrically charged with the insulator, the metal with a smaller work function leads to the insulator particle with a larger Q/m. As the moving distance of the particles increases beyond 230 mm, the particle charge ratio decreases. The particle charge-mass ratio is consistent with the trend of the charge-mass ratio deduced from the capacitance model.

Jun 3, 2023

By Y. Zhang, C. Zhou, M. Girman

Wireless technologies are increasingly being implemented in underground mines for various purposes such as communications, tracking, remote control, remote sensing, and environmental monitoring. However, the adoption comes with risks as common wireless systems, such as WiFi, Bluetooth, IWT (Innovative Wireless Technologies) wireless system, often operate in the unlicensed ISM (industrial, scientific, and medical) band. The shared nature of the ISM band can lead to interference among devices and consequently cause performance degradation and reliability issues. In this study, we developed two wireless communication evaluation boards as a tool to evaluate the performance and reliability of a wireless system with the presence of electromagnetic interferences (EMI) from other wireless systems in underground environments. We adjusted various parameters including signal power from adjacent frequency channels, noise power within the same channel, the movement of personnel, and communication packet size. Our findings indicate that, while the power of the EMI source plays a key role, the motion of personnel in the tunnel also has a strong impact on performance, and this impact increases as the power of EMI sources increases. In noisy environments, smaller packet sizes are preferable as they enhance the likelihood of successful transmission. High levels of interference or noise can lead to increased packet loss or error rates, potentially causing communication links to fail completely or become ineffective. The evaluation boards utilized in this study are based on a practical wireless transmission system deployed in a remote controller for a heavy mining machinery used in underground coal mines. The results and findings presented in this paper can aid in the design of wireless systems that are resilient to EMI in underground mining environments.

Feb 1, 2025

By J. F. Snyder

Minor elements determined by atomic absorption spectroscopy include: zinc, cadmium, copper, cobalt, nickel, chromium, manganese, and iron. Of these elements, only three; zinc, cadmium, and copper are found to have been introduced with the ore-forming fluids. Iron, manganese, chromium, and nickel were increased in dolo-stone lithologies when compared to limestone lithologies. The uniform distribution of cobalt suggests this element was neither increased nor decreased during ore emplacement nor during dolomitization of the rocks. Zinc increases adjacent to ore result from leakages into open spaces rather than as pervasive aureoles surrounding ore bodies.

Jan 1, 1977

By III Basham

As environmental laws and regulations become more complex and the economic cost of non-compliance becomes greater, periodic assessment of environmental compliance, identification of potential liability and implementation of any necessary remedial action should be a standard part of the operational methods of any successful business. The title of this paper "Environmental Audits, A Shield, A Sword or A Trojan Horse?" is intended to draw attention to the fact that environmental audits can be used positively to shield a business operations from actual or potential environmental liability; can be used proactively as a 'sword" in both a marketing context ("do business with us because we conduct our business safely and professionally?) and as a mechanism for developing positive relationships with environmental regulators; and, used negatively, as a "Trojan horse", by developing information which those same environmental regulators (or the public) use in an enforcement context against your business or that of your clients. This paper will discuss the concept of environmental audits in general; the pros and cons of conducting the same; and the role of the attorney, as part of the "audit" team, to insure, to the greatest extent possible, that the audit process is productive from both a managerial and legal perspective.

Jan 1, 1992

By Karl V. Lindell

Asbestos is not the name of a distinct mineral species, but rather the commercial term applied to the fibrous form of several minerals differing widely in composition. There are some 30 known varieties of asbestos but of this number only 6 are of economic importance, and these, in order of economic significance are chrysotile, crocidolite (or blue asbestos), amosite, anthophyllite, actinolite and tremolite. Chrysotile asbestos was formed by the introduction of hydrothermal solutions into fractures in serpentinised ultrabasic host rocks. These solutions dissolved magnesium silicate from the wall rocks, and with subsequent lower temperature and pressure they became supersaturated, and crystals of chrysotile asbestos formed. The chemical composition is variable but is classified as a hydrous magnesium silicate, containing a high percentage of magnesia and water, plus varying amounts of alumina and ferrous and ferric iron. Other asbestos minerals are formed by a similar process but with a different host rock e.g. crocidolite occurs only in iron' formation. The chemical composition of asbestos minerals other than chrysotile, shows a wide variation, but in general may be classified as silicates, or metasilicates, containing varying amounts of calcium, magnesium, sodium and iron.

Jan 1, 1964

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

By N. S. Tanious

This work was completed prior to the author's appointment with the Nuclear Regulatory Commission (NRC). Therefore the views and conclusions contained in this paper are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the NRC. Reference to specific brands, instruments, or trade names is made to facilitate understanding and does not imply endorsement by the author or the NRC.

Jan 1, 1987

By Y. C. Guan

In an attempt to replace the traditional cyanide process of extracting gold, a new technology using ammoniacal solutions has been developed. In this study, the electrochemical behavior of gold in ammoniacal solutions at temperatures above 100°C has been investigated. An electrochemical cell in an autoclave has been introduced to carry out this study. The system consists of a gold working electrode, a platinum counter electrode, and an external saturated calomel electrode (SCE) which is connected to the autoclave system through a Birch wood plug. Techniques used in this study included potentiodynamic polarization, galvanostatic polarization, cyclic voltammetry, and Tafel polarization. The electrochemical reaction mechanisms governing the dissolution process are presented.

Jan 1, 1996

By Robert H. Hooff

The Vor-Siv Dewatering and Classifying Unit was developed by the Polish Coal Industry because of a need for a unit that would dewater and classify high volumes of solids in water slurry. To be practical, the unit needed to be relatively small in size, simple in design, involve low operating costs, and be able to give a dewatered product of less than 30% moisture. The answer to the above mentioned criteria was the Vortex Dewatering Sieve or, as we refer to it, the Vor-Siv. The original installation of the unit, as we know it today, began in 1963 when the Pols installed the unit in a full scale pilot application. By 1966, at least 30 of these units were installed throughout the Polish Coal Industry. This equipment was originally introduced in the United States in 1966 at the Fifth International Coal Preparation Meeting in Pittsburgh, Pennsylvania. The first installation in the United States was not achieved until 1970, when Mr. Fred Sachs of The Valley Camp Coal Company, Triadelphia, West Virginia, installed a Vor-Siv in a retrofit application. To date, there are 36 Vor-Sivs installed in this country and 29 in the process of being installed or delivered.

Jan 1, 1976

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using a simulation that includes random number generators. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution selected for the random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing to be completed and verification of how representative the samples are.

Jan 1, 2000

By Barrie C. Butt

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been in progress for six years and the writer has been intimately associated with the project during the five years of exploration and the six years of exploitation. The industry is possibly aware of the fact that the Woodsreef Mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and of the fibre. Because of these unique features, a large volume of research has been undertaken by Woodsreef and by other scientific organisations in Australia, England and Canada on the Woodsreef fibre. The answers to some of the problems have negated some semi-sacred concepts of asbestos ore milling and led to the development of new techniques, such as the adoption of microscopic fibre counts as a routine procedure; the modification of accepted evaluation procedures; the development of new machines for dedusting fibres, and to the recognition of a fibre with a unique milling behaviour pattern and, possibly, properties. The problems experienced can be divided broadly into those associated with the geology and those associated with the physical properties of the fibre. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognised during the exploration stages a feasibility evaluation may be just that little closer to the actual.

Jan 1, 1978

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By Laura Suarez, Jörgen Kajberg, Pär Jonsén

In recent years, slag, a residue from pyrometallurgical processes, has become more attractive in circular economy frameworks to increase the efficient use of resources throughout the life cycle of steel products and help in the reduction of carbon emissions. Its applicability is strongly dependent on the particle size, and therefore, the optimization of breaking processes should be approached by increasing the knowledge of the dynamics of slag to promote fracture. Increasing the knowledge on themechanical response ofmanganese slag opens up the potential for the development of cost-effective numerical models, e.g., constitutive models based on inverse engineering calibration frameworks or digital twins. In this study, rate-dependent tests of manganese slag have been performed using a split Hopkinson pressure bar device for testing its dynamic mechanical response. In order to obtain information about the crack initiation and fracture process, 2D ultra-high speed imaging was implemented with a sampling frequency of 663,200 fps for diametrically loaded specimens. Full-field deformation measurements using digital image correlation (DIC) techniques showed a staggered fracture process where failure points on mechanical response curves vary due to the internal events happening in the material. Localized frictional occurrences and inertial effects acting inside the pre-cracked matrix have a strong effect on the global mechanical response, and therefore, a great variability of strengths was obtained.

Nov 3, 2023

By E. Fregeau-Wu

To recycle steelmaking slags for their iron, manganese, and lime contents, removal of the phosphorus-bearing dicalcium silicate and calcium phosphate is essential. Slow-cooling of slags was necessary to promote the sufficient grain growth to achieve liberation. In-situ grain size distribution determination showed that a high soaking temperature, a long soaking time, a very slow cooling rate, and the addition of fluorspar were shown to promote grain growth. High gradient magnetic separation on slow-cooled slags removed much of the dicalcium silicate. Liberation modelling was used to discuss the breakage and beneficiation characteristics of the slow-cooled slags.

Jan 1, 1992

By Dirk van Zvl

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1984

Good morning ladies and gentlemen of the AIME. I was doubly pleased when Toby Yu asked me to present to you my thoughts on the past, the present, and the future of bulk transportation by barge. My first pleasure comes from sharing with you the subject that has been my career for many years. I love this industry in the same way Mark Twain loved our rivers. Somehow, I can find in all of the activities that make up this crazy barge business the same sort of excitement that he found in "steam boating." The second reason for my enthusiasm is that Toby carefully pointed out that the presentation had to be kept to a maximum of 15 minutes. I can promise you that I will hold to his maximum time limit.

Jan 1, 1982

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981