Search Documents

By S. S. Hsieh

Bench-scale beneficiation studies were made on Idaho dolomitic phosphate rock using the TVA carbonate flotation process. The process employed diphosphonic acid as a phosphate mineral depressant and fatty acid as a carbonate mineral collector. Silica was subsequently rejected as float using an amine collector, with phosphate product recovered as the sink fraction. Two samples of prepared flotation feed from commercial operation were used; one contained 21% P205 and 3.2% MgO, and the other contained 26% P205 and 1.8% MgO. The results indicate that concentrates containing 31-33% P205 and 1% or less MgO can be obtained, with P205 recovery of about 80%.

Jan 1, 1984

By W. Norman Sims

A number of forces are at work that are now having an influence on coal handling systems. Changes are occurring and will be occurring at an increasing rate during the next few years. 1. Environmental concerns will dictate that dust pollution and spontaneous combustion and its resulting problems be rigidly controlled. 2. Slurry pipelines will be a reality despite the opposition of the railroads because they are economical and make good business sense. Artifical roadblocks can only survive for a limited time. 3. Coal is now and will remain the most economic fuel, particularly for power generation. This is true in most of the developed nations not just the United States. Increase in demand requires a close inspection of transportation systems. 4. A projected major increase in the export of U.S. coals may never occur without major port developments not the least of which will be the ability to accommodate large ships without demurrage time now affecting such shipments at U.S. Ports.

Jan 1, 1982

By D. W. Alexander

In 1993, CONSOL began investigating new methods of permanently filling coal mine shafts, which after ventilation is stopped, may contain a potentially hazardous atmosphere. Fill materials such as fly ash/cement can be pumped, are non-combustible and non-incendiary but tend to flow into the mine entries. A non-flowable mixture has been developed that minimizes the volume of fill used. The paper presents our recent shaft filling experience including fly ash material properties, mix designs, field problems, placement success, and gas testing techniques.

Jan 1, 1996

By James L. McGregor

St. Joseph Lead Company has been paying incentive bonuses for well over 40 years. In 1958 almost half of St. Joe's 1,860 employees in Southeast Missouri received some form of incentive bonus in addition to their guaranteed wages. There are very few payroll jobs in St. Joe s Southeast Missouri organization that lend themselves to a reasonably good measurement of production or quality, or both, where an incentive bonus is not paid. The term "Incentive Bonus" is used to differentiate betwen bonuses that are based on quantity or quality of work, and those that are merely additional pay of a standard amount per hour or day because of an employee being temporarily assigned to some unusual task, An employee temporarily assigned to a job where the working conditions make the job performance unusually difficult or where a special skill is used is often given a bonus of some standard amount per hour or shift in addition to his usual rate. This is merely a convenient way of paying something extra without disturbing the normal rate structure. Actually, it is differential pay similar to that almost universally paid for evening and night shift work. Bonuses of that type are not being considered in this paper. The basic reason or theory for paying incentive bonuses 9s to get improved production at lower cost, Unfortunately, it is often difficult, if not impossible, to find a yardstick by which it can be definitely proved that a particular bonus plan is accomplishing its purpose, It becomes, then, a matter of judgment on the part of management personnel as to the value of the bonus plan. The fact that St. Joe Lead Company has continued to pay bonuses for over 40 yews and has increased the number of bonus schedules used attests to a definite belief that they are beneficial to the company's successful operations.

Jan 1, 1960

By Giuseppe Gaspari, Xiangrong Wang

The pandemic emergency is forcing transit agencies to define strategies allowing social distancing, which are more challenging in underground interchange stations in crowded downtown cores. Toronto Transit Commission’s (TTC’s) Bloor-Yonge Station Capacity Improvement Project in Toronto was approved to meet increasing demand and represents an opportunity to fight COVID-19. This paper discusses cost-effective solutions in expanding the cut-and-cover station box over the existing Toronto Subway Line 2 and connecting it through ventilation openings in the cast-iron tunnel liner. Potential uplift risks and structural damage due to minimal vertical clearance were analyzed via three-dimensional finite element analyses with advanced constitutive laws to simulate the multi-stage construction process. Based on the simulation results, a series of countermeasures, including excavation support systems, king posts, ground-consolidations, and liner reinforcements were integrated into comprehensive design options to ensure the serviceability and structural integrity of the subway tunnels.

Jun 13, 2021

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

By Levent Ozdemir, Charles Merguerian

Between 1996 and 1999, a high-performance Robbins TBM [235-282] excavated a 5 mile long, 23´2? wide, and ~700´ deep tunnel through the subsurface of southwestern Queens. Low penetration rates (~6´/hr [actual] vs. ~9´/hr [anticipated])resulted from changed rock mass conditions mostly attributable to high-grade metamorphism of the rocks. Over a three-year period, as-built circumferential geologic mapping (scale 1?=10´) and digital imagery of the tunnel, fracture and fault analysis, structural, lithologic, and petrographic studies have shown that the rocks of the Queens Tunnel consist of orthogneiss of mesocratic, leucocratic, and mafic composition. These metaigneous rocks developed coarse-grained fabrics during Grenvillian (~1.0 Ga) granulite facies metamorphism, and retained their nearly anhydrous, poorly foliated character during subsequent high-grade Ordoviciande formation. Lacking a penetrative foliation, the coarse granoblastic rock texture and extraordinary garnet content (up to 50% in some zones) together proved animpediment to efficient chip production and resulted in bimodal production of blocks and excessive fines. TBM excavation of the Queens Tunnel was also hindered by geological conditions that included unexpected lithology and rock fabric orientation, a zone of crosscutting hypabyssal rhyodacite dikes, and unanticipated extent of brittle faults. The dikes and brittle faults produced blocky ground conditions and a collapsing face condition that produced cutter damage and decreased utilization. Such fundamental textural, mineralogic, and lithologic control over hard-rock TBM penetration can be predicted by careful pre-bid geological analysis. To determine the causes of lower than anticipated TBM performance, a detailed investigation was carried out that included analysis of operational data from the TBM data logger and an extensive laboratory test program on cores retrieved from tunnel walls. Integrated laboratory testing included punch, point load, tensile strength, Cerchar abrasivity, and linear cutting tests, independent petrographic analysis and machine performance analysis. These allied investigations have provided quantification that the rock mass exhibited an unusually high degree of toughness and rock directional properties and established geological causes for decreased TBM penetration rates.

Jan 1, 2003

By A. Davis

Pit lake chemistry depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock versus oxidizable sulfide content, and the alkalinity of recharging ground water. In this paper, we assess the geochemistry of 11 existing pit lakes, ranging from the acidic Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington Pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits with the long-term pit lake chemistry lying on a geochemical continuum between end members consisting of influent calcium bicarbonate ground water, and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1996

By William Watson

Coal production in the United States in 2010 increased to a level of 960 Mt (1,085.3 million st), according to preliminary data from the U.S. Energy Information Administration (EIA), an increase of 1 percent, or 9.43 Mt (10.4 million st) above the 2009 level of 975 Mt (1,074.9 million st) (Table 1). In 2010, U.S. coal consumption increased in all sectors except commercial and institutional, while total coal stocks fell slightly for the year. Coal consumption in the electric power sector in 2010 was higher by 4.5 percent, while coking coal consumption increased by 37.9 percent and the other industrial sector increased by 7.1 percent. The commercial and institutional sector, which prior to 2008 had been called the ?residential and commercial? sector and is the smallest of all the coal-consuming sectors, declined by 3.1 percent in 2010. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports increased from the 2009 levels due mostly to higher demand for metallurgical coal, while coal imports decreased for a third year in a row. The increase in coal consumption for electric generation during the year was the consequence of improving domestic economic conditions further bolstered by a cold winter and warm summer in important coal-consuming regions. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. increased in 2010 by 4.2 percent. Coal-based generation also increased, resulting in a 38-Mt (42-million st) increase in coal consumed in the electric power sector. Coal use in all the sectors other than the electric power sector increased by 13.9 percent to a level of 65.9 Mt (72.7 million st).

Jan 1, 2011

By Roger L. Hulette

Mt. Newman Mining Co. is now completing an expansion program, begun even before initial construction was complete, which will result in facilities with the ability to ship over 30 million tons of iron ore per year by early 1973. Confidence in such rapid future growth was evidenced by careful planning for the future expansion of those facilities provided for initial operation of the project which first shipped ore on 1 April 1969. Ore sales contracts totaling more than 300 million tons have been negotiated, thus justifying the optimism which led the joint venturers to provide over $200 million in initial investment and a like amount in capital required to finance the continuing expansion program. Members of the Mt. Newman Joint Venture are: Amax Iron Ore Corporation - 25% (a subsidiary of American Metals Climax) Pilbara Iron Ltd. - 30% (a subsidiary of Colonial Sugar Refining) Dampier Mining Ltd. - 30% (a subsidiary of Broken Hill Proprietary) Seltrust Iron Ore Ltd. - 5% (a subsidiary of Selection Trust Ltd. of London) ? Mitsui C. Itoh Iron Ore Pty. Ltd. - 10% Mt. Newman Mining Co. Pty. Ltd. manages the project on behalf of the five companies which make up the joint venture.

Jan 1, 1972

By Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapoconcentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporate playa lakes.

Jan 1, 1997

By R. Bruce Tippin

because of the mineral's high monetary value and the spotty occurrence of free gold in the deposit. Setting up a plant sampling procedure by simply applying the usual statistical sampling theory was questionable. Two sampling concepts were considered in the sampling study: o a sufficient number of assays can be taken such that the average determined from these individual samples represents a known quantity of ore. o a sufficient weight of sample can be taken such that when assayed it represents a known quantity of ore. The test program included evaluation of sampling techniques, sample preparation and analytical methods. The overall sampling program is depicted in Figure 2.

Jan 1, 1985

By K. J. Bruxvoort

Background ground water quality is often used to drive remediation programs at sites with waters affected by mining activities. In the past these levels were sometimes chosen without rigorous statistical and geochemical analysis. A probability distribution approach was used at the Sweetwater Uranium Project to separate a large set of geochemical data into populations that represent contributions from different sources. Natural background populations were identified for major ions, metals, and radionuclides, and were submitted to the Nuclear Regulatory Commission to modify the extent of a Corrective Action Program and to establish control limits for future monitoring.

Jan 1, 1998

By Raymond L. Lowrie

Deregulation, as authorized by the Energy Policy Act of 1992 (PL102-486) allows free-market competition in the electric-utility industry. As the act unfolds, though, uncertainties abound about the type, degree and direction of impacts throughout the affected economy — from fuel suppliers to electricity generators and from power distributors to energy consumers. Instead of having a familiar base of captive customers and electricity prices fixed by negotiation with state public utility commissions, utility companies are preparing for open, free-market competition. They are looking at all areas, including fuel supply, to cut costs to remain competitive. Humorous anecdotes are told about utility companies shunning insiders for senior executive positions. Instead, they are opting for people from the telephone or other industries with deregulation experience. And there are light-hearted stories about a trend away from traditional electric-company names, such as the name of a city or state followed by Edison or Power and Light, to space-age names, such as Ameren, Entergy, Illinova or Unicom. No one wants to be left behind or be perceived to be left behind.

Jan 1, 1996

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By P. R. Taylor

This investigation (Bowles, 1990) involves consideration of technology utilized by three separate fields of metallurgy and materials science: 1) The recovery of metals employing the use of solvent extraction, 2) The fabrication of materials using powder metallurgy, and 3) The use of composite materials in fabrication of engineering materials. The research considers each of the processes in order to realize the benefits of each. In light of the fact that materials have an intended use -it does seem plausible to simplify the process required between "mother earth" and final use. For instance, a primary copper producer that already employs a solvent extraction and electrowinning process could produce value added products directly. Part of the existing extractant flow could be diverted into a pressurized hydrogen stripping process in order to produce specialty composite powders. Innumerable methods have been employed for the recovery of metals; solvent extraction, the one considered in this study, was used due to the possibility of it providing a pure powdered metal. The use of solvent extraction in the recovery of metals has gained wide acceptance and its use proves beneficial in many applications (Ritchey and Ashbrook, 1984). Pressure hydrogen stripping of solvent extractants may provide the benefit of flowsheet simplification compared to conventional solvent extraction followed by electrowinning. It may also provide the benefit of direct production of high purity metal powder (Demopoulos and Distin, 1985).

Jan 1, 1992

By T. I. Martinovic

A major investigative' program was conducted on the development of an acceptable substitute organic binder for bentonite for the pelletizing of the Iron Ore Company of Canada's Carol concentrate. The first phase of the program covered an evaluation of several organic binders in laboratory tire balling in order to identify the most promising potential organic binders. Based on the green ball quality obtained, Peridur C-10, Alchem 8C26 and peat moss were selected for full scale pot-grate testwork. The selected binders were tested with various pelletizing mixes (acid, dolomite, limestone and fully fluxed). The pot-grate test results showed that an acceptable pellet quality can be produced with the use of Peridur C-10.

Jan 1, 1989

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35 percent), ceramics and glass (32 percent), lubricating greases (9 percent), air treatment (5 percent), continuous casting mould flux powders (5 percent), polymer production (4 percent), primary aluminum production (1 percent) and other uses (9 percent) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014).In the 1990s, the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced during this period were consumed in the glass, ceramics and aluminum industries. In the 1980s and 1990s, there were two major lithium operations in the United States: brine operations at Silver Peak, NV and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, NC. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period, it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994).Lithium is still produced from the brine operations at Silver Peak. But in more recent years, Chile has become the world’s leading producer of lithium carbonate from brines. Australia has maintained its position as the world’s largest producer of lithium mineral concentrate, the majority of which is exported to China to produce lithium carbonate and lithium hydroxide (Jaskula, 2014).A spodumene concentrate was also produced at the Tanco Mine in Manitoba, Canada beginning in the 1980s through to 2010 when lithium operations were suspended due to fluctuations in the lithium market price (Martins et al., 2013)."

Jan 7, 2017