Search Documents

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By D. H. White

The term "block caving" as used in this text includes panel caving and mass caving as described by Julin and Tobie (1973). This method reportedly was conceived in 1895 when a block of ore ranging up to 200 ft (61 m) in width was undercut at the Pewabic Mine on the Menominee Range in Michigan (Bucky, 1956). Over the years this method has evolved largely as a consequence of trial and error in which operators became acutely aware of what nature would allow and what it would not. Today block caving remains somewhat of an art rather than a science where experience often dictates what needs to be done. With the plunging prices of base and specialty metals in the early 1980s caving mines sought to reduce operating and development costs in order to return to profitability. For some this became an impossible task given the design, grade and operating costs of the day and closure became the only alternative. One lesson learned from the experiences of the 80s is that survivability depends on cost competitiveness and this implies the efficient use of resources and technology. To this end applied rock mechanics serves as a useful tool. The purpose of this paper is to show how Geomechanics can be used? in block caving to facilitate sound decision making and how this equates to dollars saved. Features of mining method selection, design and operation are discussed as related to this theme.

Jan 1, 1990

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

By James S. Browning

Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama. 1, 2, 3 Whereas in western North Carolina these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites.4 To a lesser extent, mica is produced as a byproduct of feldspars and spodumene.6 Past research by the Bureau of Mines has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica." This method requires thorough desliming of the ore with consequent fine mica losses. The other method utilizes an alkaline-anionic-cationic process for recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica. 8, 9, 10, 11, 12, 13 The latter process has also been successfully applied to a micaceous schist ore from California.14 This report summarizes the results of these research studies. Both of the flotation processes developed by the Bureau of Mines have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores.

Jan 1, 1969

By M. Ghiani

Biohydrometallurgy originated, some forty years ago, from an environmental problem, namely the serious pollution of the Ohio river by acid drainage water coming from neighboring subbituminous coal mines. Studies aimed at elucidating the cause of the intensive oxidation of the iron sulfide (pyrite) inclusions of those coals, led to the discovery of a bacterium, Thiobacillus ferrooxidans (Temple and Colmer, 1951), capable of acting as a catalyzer, accelerating the otherwise very slow chemical oxidation of iron sulfide to rates many orders of magnitude higher. However, it is now recognized that the biotechnology of microbial mining dates back to 1963, when the ability of this bacterium to solubilize copper from sulfide ores was ascertained (Razzell and Trussell, 1963). Much research has been carried out on biohydrometallurgy over these last 25 years and is still being actively conducted all over the world. The interdisciplinary nature of this young branch of science and technology is reflected by the variety of experts involved: microbiologists, mining engineers, hydrometallurgists, physico-chemists, mineralogists, solid-state physicists and biochemists. This intensive research effort has provided a solid background on the fundamentals of this technology, although many important issues have still to be solved, amongst which the enzymatic mechanisms controlling biocatalysis of mineral sulfides dissolution, the influence of bulk- and surface solid-state physics of metal sulfides on dissolution mechanisms, the interaction of the various strains composing natural microbial floras. Their elucidation should permit the rationalization of biohydrometallurgical techniques and the optimization of commercial processes. Biohydrometallurgy has already achieved satisfactory results: copper recovery from submarginal copper sulfide run-of-mine ores (i.e. assaying less than 0.3% Cu) by in-situ, dump and/or heap leaching is successfully practised in many countries and uranium recovery through bioleaching is competitive with other leaching processes.

Jan 1, 1987

By C. E. Jordan

The Bureau of Mines investigated a simultaneous elutriation and flotation technique for separating polyethylene terephthalate (PET) from polyvinylchloride (PVC). The Tuscaloosa Research Center, through a cooperative agreement with a recycling company, devised an elutriation-flotation method for beneficiating the mixed heavy plastics portion of municipal solid wastes which is composed of polystyrene (PS), PET, and PVC. A sodium carbonate brine was used to remove the lighter PS from the heavier PET and PVC. Over 98 pct of the PS was recovered in a high purity PS concentrate containing 99.7 pct PS, The remaining PET and PVC mixture was washed to remove the brine salts that would be harmful to the flotation process. The clean PET and PVC mixture was conditioned in a solution of 45 g/t gelatine and floated in a short (l-m) column flotation cell in an upward flow of water. In a single flotation step, over 75 pct of the PET was recovered in a high purity product containing 99.8 pct PET. The bubbles attached to the PET lowered the effective density of the PET-bubble agglomerate and allowed successful separation of these agglomerates from the PVC plastic pieces. This method separated two-thirds of the mixed plastics fraction into high purity PS and PET products suitable for recycling and left only one-third of the plastics in the mixed plastics product.

Jan 1, 1992

By E. F. Klein, R. L. Eacret

Introduction In contrast to the general type of crushing mechanism in which the crushing surfaces alternately approach and withdraw from each other, described earlier in this section, and continuous-pressure break¬ers such as rolls and roller mills that will be described in a later chapter, impact crushers load by striking pieces of rock while in free fall and hurling them at high speed against stationary surfaces. Because the impact crusher depends for its effectiveness upon high velocity, wear is greater than in the slower-moving jaw and cone¬type wear parts, and for this reason its use is strictly limited to rela¬tively soft, friable, and sticky rocks that are characteristic of many nonmetallic mineral deposits. A few of these are phosphates, lime¬stone, barite, clay, asbestos rock, and coal. However, several examples of their use on soft lead-zinc and precious metal ores have been known. Although the use of impact crushers is expanding today into the range of ores containing as much as 15-18% silica, Taggart16 set the practical limit at 5%, and in the 1940s and 1950s several installa¬tions in the US and western Europe exceeded the limits of economical maintenance and were quickly superseded by the slower-moving, con¬ventional crushers. A rock that tends to be plastic or bouncy in a jaw or gyratory crusher when the force is applied slowly to reach ultimate strength, may become brittle with rapid loading and thus increase the effective¬ness of the applied forces. For this reason it is to be expected that as the quality of hammers, grates, plates, and cages improves with advances in steel technology, the use of high-speed crushers of this kind will increase. Terminology Modern usage differentiates between the impactor and the hammer mill, the former relying primarily on the impact of hammers (fixed or free-swinging) and secondarily upon pieces striking one another or steel surfaces; the hammer mill relies on both the centrifugal impact force of free-swinging hammers and the attrition and shear action between these hammers and well-placed grates suspended at the bot¬tom just below the hammer circle. The hammer mill, because of its grate discharge, restricts discharge of oversize rock to the grate open¬ing, while at the same time providing a trap for removal of tramp iron or other uncrushables. The impactor discharges free, so generally works with a screen to control product sizes. The question of terminology, impactor vs, hammer mill, creates difficulties because the similarities appear to outweigh the differences by far; if one were to list the similarities in order of importance and then the differences, he would be forced to conclude that they would best be dealt with as a single kind of crusher. Taggart16 gave it four names and added "as it is variously known," but it must be remembered that in 1945 the machine was nearly exclusively of the flailing-hammer type, while today the fixed-hammer rotor is also com¬mon. In this chapter the terms impactor and hammer mill will be used where they seem to apply. It is perhaps unfortunate that this terminology is being confused with rock breaking at the mine, usually with hand-held tools, e.g., the article "High-Energy Impact Rockbreaking" by Grantmyre and Hawkes, CIM Bulletin, August 1975. General Description Impact breakers, impact crushers, and hammer mills accomplish material breaking and reduction primarily through impact action of the material with fixed or free-swinging hammers revolving about a central rotor. The material to be crushed enters through an opening at the top or top side known as the "feed opening" or "hopper opening" and falls into the path of rotation (hammer circle) of the hammers. Initial breakage is accomplished in midair by collision of the dropping feed material with high-speed hammers. The second stage of breakage occurs when the pieces hit plates or breaker bars which line the crusher boxlike frame. Hammer mills rely further on a shearing and attrition action between free-swinging hammers and grid bars or grates at the crusher bottom which restrict discharge of oversize material until it is broken sufficiently to pass through the grid opening. The term hammer is used in reference to the piece which strikes the material, whether it is fixed on the rotor or free-swinging. It

Jan 1, 1985

By R. M. Jacobs

Can your company afford to issue a check today for $100,000, $500,000, $2,000,000, or $22,000,000? This is what it might cost your company if it is on the losing end of a product liability suit. During the past 10 to 15 years, the number of product liability actions has grown from a handful per year level to a hundreds of thousands per year level. Settlements and awards in the tens and hundreds of thousands of dollars are not unusual in these days. The largest award that the authors haw heard about is a case involving a private airplane and the death of four men, which was awarded over $22,000,000. In the materials handling field, a fork lift truck, ordered with an overhead guard, was delivered without a guard because one was not available at the time. An accident with serious personal injury followed. Wouldn't it have been better to have waited until the guard was available before delivering the unit? Answer: a quarter of a million dollars better -- the cost of the settlement. Hoisting devices are also not without their liability precedents. In a 1960 case, an employee was injured when a load abruptly fell from a hoist. It was determined that the operator could not possibly have caused such a fall had the hoist been functioning properly. The case was compounded when the manufacturer of the hoist contended that the load had been improperly connected to the device, since the same hoist was used to remove the weight from the injured man without another malfunction.

Jan 1, 1973

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By C. R. Stephan

The Mine Safety and Health Administration's (MSHA) Ventilation Division continues to evaluate proposed explosion-resistant seal designs. There are currently eleven specific designs for explosion-resistant seals that are suitable for construction in underground coal mines. Seal construction in operating mines must be equivalent to those constructed in the Experimental Mine during the explosion testing program. Accidental failures of seals have occurred due to explosion pressures below 138 Kpa (20 psi). The possibility exists that the failed seals were not properly constructed. Also, conditions in the vicinity of the seals may change. Water may accumulate against the seals, heave or sag may cause detrimental effects on the seals, and sloughage of the ribs may negate hitching. If seals are not properly installed or maintained, they could fail when subjected to explosion pressures. If seals fail for any reason, the possibility exists for explosion propagation throughout large areas of the mine. There could be catastrophic consequences to an event of this nature. This report will present a limited discussion on the construction of each of these seals and will address related issues.

Jan 1, 2001

By Pablo Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occuring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, California recovers potash from natural brines, but uses fuel to accomplish evaporation. Under proper meteorological conditions the use of solar evaporation might be desirable from the economical standpoint. Of course, this may not be true when, if by artificial evaporation, a group of very valuable salts are recovered. This is the case of the American Potash operation at Trona. Solar evaporation has its limits. The working temperature is low. We may say, just to cover most areas of the world where solar evaporation may be practical, that it will take place between 18°C and perhaps around 45°C. In most cases the average working temperature expected will be around 25°C.

Jan 1, 1963

By L. Harris

The Yanacocha project is the first foreign investment in Peruvian mining since Cuajone during 1976. Three years after the project began, it has become the largest producer of gold from heap-leach operations in the world and the top producer in Latin America. The success of Minera Yanacocha SA (MYSA) opens a new chapter in Peruvian mining with the exploitation of its widely spread gold deposits. And it has attracted the interest of foreign investors in Peru’s mineral resources. Construction began on Aug. 1, 1992. The first gold bar was poured on Aug. 7, 1993 from ore from the Carachugo Mine. During 1993, Minera Yanacocha produced 2.5 t (81,000 oz) of gold and 9.4 t (304,000 oz) during1994 (40% above budget). Production was expected to exceed 15.5 t (500,000oz) during 1995 with the start-up the Maqui Maqui Mine.

Jan 1, 1996

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By Charles E. Michener

This paper deals with the occurrence of basic and ultrabasic rocks and their relationship in space and time to major structures of the earth. In order to introduce the paper properly, I must go back a little and try to put the subject in perspective. In the brief time that geology has been a scientific occupation, ore deposits have been grouped and classified in various ways depending on the theories that happened to be popular at the time. Some of the early scientists said that ore came from fire, other schools argued that ore originated from water. Then came the lateral secretionists and in later years the hydrothermalists led by the Lindgren school and the latter has largely been accepted as the modern concept of ore deposits. It now seems apparent that the hydrothermal school is being seriously challenged by other schools of thought. It also seems that we have reached the point where we should be willing to admit that we do not really know in most cases how the ore got to its present position. However, for practical purposes, we can classify ore deposits as to the environment in which they do occur. This is not difficult and gives the field geologist and the mining engineer something to work with and to believe in, and it gives them a basis for carrying out their field work. On the screen, Figure 1, there is a classification of ore deposits based on the environment. Under each classification is listed the more prominent metals which are characteristic of that

Jan 1, 1971

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By LeRoy D. Loy

Would you believe me if I told you the constant battle between Government regulatory agencies and industry could be won by both sides? No, I'm not crazy, nor have I been soaking up any of that fine Kentucky whitelightning. But I have recently been a participant in a battle where both sides won. Actually, I'm using the term "battle" loosely because, in reality, it wasn't a battle at all - despite the fact that all the ingredients were there for a monumental struggle; i.e.. government, industry, special interest groups and a controversial issue - the development of effluent limitations. I'd like to tell you about it. Historically, on one side of the battle, government has always been ac¬cused of adopting regulations with limited evaluation of existing technologies; and then with seemingly no regard for the economic consequences. On the other side, industry gets punished by government's harsh actions because of their past "do-nothing" attitude toward pollution control. Recently, this battle seems to be losing steam, because both government and industry are beginning to realize that, ultimately, they both will lose. Even more important is the fact that both sides are, or should be, working for industrial expansion compatible with environmental protection.

Jan 1, 1977

By M. E. Kuchta

Surface coal mine design can be facilitated with the use of an interactive graphics personal computer program. This mineral inventory and planning program (POLY CALC) is described and its use is illustrated with a case study. The case study deals with investigating a stripping sequence and associated dragline stripping requirements.

Jan 1, 1986

By K. M. Mohamed, I. B. Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to reduce rib fall accidents and fatalities in underground coal mines. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified. The paper presents a coal rib model to simulate the mechanism of the coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff mine in Australia. Fracturing of the coal rib was defined by critical values of shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data. INTRODUCTION Coal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities [1]. Despite the threat of rib falls, the amount of rib falls and rib support research conducted in the U.S. is limited compared with what has been done in pillar and roof support design. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to minimize the number of rib fall accidents and fatalities in underground coal mines."

Jan 1, 2016

By Erik S. Bernard

"INTRODUCTION Reinforced Concrete (RC) members such as beams and columns are usually required to include stirrups to maintain post-crack shear capacity, and some may include stirrups that act as confining steel to maintain structural integrity during a seismic event (eg. NZS3101, ACI 318). To achieve seismic resistance, the spacing between stirrups is usually required to be much closer than is ordinarily prescribed for non-seismically resistant structures. Each stirrup must also fully enclose the longitudinal reinforcement with long end-hooks to ensure that the contained concrete is sufficiently restrained during reverse-cycle loading and the reinforcing bars are confined to prevent buckling. The close spacing between stirrups can lead to congestion of reinforcement within members, and can also be expensive to construct due to the labor-intensive nature of steel fixing. A possible alternative to closely-spaced stirrups is the use of fibers to provide restraint and confinement during a seismic event, although this is not yet recognized in codes. Previous experimental research (Jiuru et al, 1992; Filiatrault et al, 1995; Bayasi and Gebman, 2002; Billington and Yoon, 2004) has demonstrated that steel fibers are relatively effective in this application, but suffer the problem that their stiffness can make them difficult to consolidate within an already tight reinforcement cage, especially if they are relatively long (>40 mm). Moreover, steel fiber reinforced concrete (SFRC) is subject to embrittlement with the passage of time, leading to a steady loss of ductility beyond crack widths of 1-2 mm (Banthia and Trottier, 1994; Bernard and Hanke, 2002; Bernard, 2014; Bjontegaard et al, 2014; Bernard, 2015). Since cracks during seismic events are generally much larger than this, embrittlement may present a challenge to the long-term efficacy of SFRC during seismic events. An alternative to steel fibers for enhancement of seismic resistance is the use of macro-synthetic fibers. This type of fiber usually offers the advantage of being flexible so that consolidation is easier between reinforcing bars. They also offer superior durability compared to steel fibers and can reduce flexural crack widths (Bernard, 2016). Several recent small-scale investigations (Ma et al, 2012; Carnovale, 2012; Osorio et al, 2014) have indicated that macro-synthetic fibers can produce meaningful improvements in seismic resistance if used in combination with conventional steel reinforcing bars. The present investigation has extended research in this field by examining whether embossed macro-synthetic fibers can be used to increase the spacing between stirrups while maintaining seismic resistance."

Jan 1, 2016