Search Documents

By Charles K. Presley

This paper deals with drilling large diameter shafts for the mining and construction industry with diameters in excess of 3 feet to more than 20 feet in diameter. It discusses appropriate applications of the rotary drill method, linings for large diameter shafts, circulation systems,, and the limitations of the method. Each specific rotary drill method is determined by the geology of the area, the depth to be drilled and the formation fluids encountered. Shaft lining or casing must be improved to result in lighter weight, higher strength and lower cost. All phases of rotary drilling equipment must be improved to drill shafts in excess of 10 feet in diameter. As these goals are reached, more shafts of large diameter will be drilled by the rotary method for the mining and construction industry.

Jan 1, 1967

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By Gary Nash

While there could be as many directions on regulations as there are viewpoints surrounding the asbestos controversy, there are a few basic criteria that generally will influence government thinking, namely: - their definition of the problem to be regulated, - their interpretation of the scientific evidence available to them, and - their sensitivities to the views of, and the implications for, various interest groups in society. Clearly, different assessments of these criteria by various governments will lead to differing regulatory regimes. The consequence, of course, is a patchwork of non-conforming regulations among nations, with all that thin implies for the distortion of international trade and the unsettling of international relations. I would therefore argue that when governments are examining regulatory action, they should explicitly take into account their common interests in stable and cordial international relations, and when possible, efforts should be made to ensure that movement on regulation is at least, in principle, in accord with the general views of the international community.

Jan 1, 1984

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By L. L. Probert

A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive x-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of particles. This paper will focus on the results for respirable quartz particles that occur in underground coal mines across the U.S. The relationship between the amount of surface-available quartz and coal seam rank is well established for Pennsylvania

Jan 1, 1994

By S. Mishra, C. Shon, D. Saylak

Only 40% of fly ash generated by the power plants in US are recycled and used for commercial applications. Of these, the high lime, Class C ash had been preferred. Systematic laboratory and field-scale studies have shown that, by including calcium chloride in the mix design of stabilization of roadbed materials, both Class C and Class F fly ashes can be effectively utilized. Test data reveal that the addition of calcium chloride to the system accelerates its curing rate, thereby increasing early strength and long term durability of the constructed road. For road construction, a preblended Class F fly ash–CaCl2 system tends to be more forgiving than the Class C fly ash–CaCl2 system. The former system produces more durable roads. The role of calcium chloride as an accelerator in these systems is discussed along with a mathematical model developed for fly ash- CaCl2 stabilized roadbed systems.

Jan 1, 2007

By John O. Marsden

"This article is an attempt to capture a presentation given at the 2016 SME Mineral & Metallurgical Processing Division (MPD) Luncheon held on Feb. 24, 2016, in Phoenix, AZ. It was presented as a tongue-in-cheek, lighthearted view of several of the issues facing our industry, while identifying some of the challenges and opportunities available to new engineers entering the industry today.Disclaimer• What you are about to read includes personal preferences, biases and occasionally arbitrary opinions.• Some readers may have dissimilar opinions on the contents and/or the rank order of the lists.There are eight top ten lists offered in this article: (1) Industry realities (2) Things a metallurgical or mineral process engineering graduate should do (3) Books every metallurgist should have on their shelf (4) Things I wish I had known (5) Legends of metallurgy (posthumous, with highlights) (6) Things we’ve forgotten (7) Mineral processing innovations of the past 20 years and, finally, (8) The future? For some items, additional context or clarification is provided after the item, while for other items no further explanation is warranted and none is offered. Top 10 industry realities1. Metal price cycles.2. Bigger is better (except when it isn’t).3. Ore grades declining across the board of metals/commodities.4. Ores becoming more complex.5. Three-fold increase in capital costs between 2004 and 2015.6. Three-fold increase in operating costs between 2004 and 2015.7. Less capital availability/challenging financial markets.8. Environmental constraints increasing.9. Socio-political constraints increasing.10. The mine manager is always impossible to work with.As Table 1 shows, there was more than a three-fold increase in gold operating costs between 2004 and 2014. The increases for copper, iron ore and other commodities were similar."

Aug 1, 2016

By Yues Bertube

Molybdenite and chalcopyrite are two often-associated minerals. In Quebec, the Gaspe Copper Company, a subsidiary of the Noranda group, currently operates a molybdenite flotation circuit to recover a one percent trace of this mineral in the chalcopyrite concentrate. The low levels of molybdeni 2 preclude the use of flotation to remove molybdenum directly from the ore while scavenging of chalcopyrite concentrate for molybdenite yields a concentrate of the latter of somewhat inadequate quality. Such a situation could possibly best be solved by hydrometallurgical means, if molybdenite could be leached selectively from the chalcopyrite concentrate. Work in the field of extractive metallurgy was initiated about 22 years ago in the laboratory of the department of mining and metallurgy at Laval University, Quebec. Following a literature search, two objectives were selected. The present talk will outline some of the results obtained to-date and it is hoped the ensuing discussion of the paper can raise questions of immediate assistance to us for the future. First, as an immediate objective of-practical use, the oxidation rates for molybdenite and chalcopyrite in alkaline media would be studied under conditions of possible industrial application. Secondly, the kinetics of mass transfer of gases in pressure reactor are to be studied. Solubility data for various gases in aqueous solutions have been gathered by a few investigators, to mention the work of Pray1, Wadsworth2, Pawlek3 and Gerlach. Scattering in experimental results and discrepancies between authors are ominously present. Kinetics of mass transfer have somewhat been more neglected. A systematic investigation by the school of Berlin has greatly helped in the design of impeller most suitable for gas dispersion, without much reference however to the solid dispersing ability of the various designs. Variables affecting rates of gas transfer to the solution have not been studied. Studies on the aqueous oxidation of sulfide minerals are much more numerous. While molybdenite has been relatively less studied, work has been carried in two areas namely in alkaline oxidation of MoS2 , work performed by Dresher2 and Wadsworth, and in the hypochlorite leach of molybdenite by Bhappu4 and co-workers, These two methods showed appreciable rates of leaching for molybdenite. In general, comparisons between rates of oxidation of this sulfide with that for chalcopyrite have not been made.

Jan 1, 1972

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce risks of coal dust-fueled explosions. The goal of this NIOSH study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust (<75 µm diameter) in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity. Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing, and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle is operated at high fluid pressures to produce smaller droplets and move more air. These findings can be used to select sprays and design spray arrays to control airborne float dust over the entire longwall ventilated opening. INTRODUCTION Coal mining processes produce airborne dust that naturally deposits on the floor, roof, and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 microns in diameter, are deposited in return entries of coal mines and can be re-entrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; NIOSH, 2006). These particles are also those most likely to participate in coal dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (CFR, 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal dust-fueled explosions. Water sprays are both effective and widely accepted as a method for controlling underground coal mine dust. In fact, water sprays are considered to be the most economical and technically feasible means of reducing dust concentrations in underground coal mines (Courtney and Cheng, 1977; Barker and Humphreys, 1996). Sprays are used in several ways to control dust in mining processes: inhibiting dust formation, immobilizing dust to prevent it from becoming airborne, and capturing airborne dust (Cheng, 1973). Reductions in airborne dust concentrations have frequently been attributed to inertial impaction between water droplets and dust particles, forming larger agglomerates which then quickly precipitate out of the airstream (McPherson, 1993). Inertial impaction activity is generally accepted as the major capture mechanism for airborne particles larger than 0.5 µm in diameter. It is this mechanism that is evaluated in this study."

Jan 1, 2017

Many investigators measured surface forces between hydrophobic macroscopic surfaces using atomic force microscope (AFM). Some investigators observed long-range attractions and attributed them to the presence of hydrophobic forces, while others suggested that they are artifacts of the nano-bubbles and cavities associated with the hydrophobic surfaces. Still others suggested that the long-range attractions are due to the electrostatic interactions between charged patches present on opposing surfaces and hence are unrelated to surface hydrophobicity. In the present work, we have measured long-range attractions between gold- (or silver-) coated surfaces hydrophobized in potassium ethyl xanthate (KEX) solutions at pH 9.2 under controlled potential conditions. The results of our AFM force measurements are consistent with those of the contact angle and voltammetry experiments, indicating that the long-range attractions are hydrophobic forces.

Jan 1, 2012

By R. K. Rajamani, A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

How do you think the US Bureau of Mines closing will affect SME? The demise of the bureau represents a challenge, an opportunity and, above all, new responsibilities for our profession. A lot of good professionals are seeking new positions. A lot of worthwhile research is available for transfer to the private sector. Logic dictates that worthwhile projects of any defunded government activities should find support in the private sector. The bureau may be gone but its legacy is deeply rooted in the profession. The bureau’s contributions will be remembered as long as there are mines and miners. Its1994 research program was divided into three major areas: environ-mental technology; health, safety and mining technology; and minerals and materials science. There must be a place in either the government or private sector to continue these worthwhile activities.

Jan 1, 1996

By P. R. Desam, J. D. Miller, A. Datta

The flow behavior of bubble-particle aggregates in separation tanks is important for many flotation systems, particularly for wastewater treatment. These aggregates can be considered as the dispersed phase in a continuous liquid phase of water and the flow characteristics determine the efficiency of the bubble separation process. In this work, a general methodology for the computational fluid dynamics (CFD) simulation of a bubble separation tank is described. This system is analyzed by Eulerian-Lagrangian approach. The momentum transfer from the dispersed phase to the continuous phase is quantified using the Particle-Source-In Cell (PSI-Cell) method. With CFD simulations, the effectiveness of different tank design parameters are evaluated in terms of the extent of bubble separation.

Jan 1, 2000

By P. Conrad

Experience has shown that, since the passage of the Surface Mining Control and Reclamation Act, over-compaction of spoil during the reclamation process has severely limited tree growth on reclaimed land. Researchers at the University of Kentucky have conducted a ten-year investigation at a surface mine in eastern Kentucky that monitored the changes in selected spoil physical characteristics for various reclamation and compaction alleviation methods. More specifically, research plots were developed for reforestation that employed three different levels of compaction and two different methods of ripping for overly compacted spoil. Each year measurements were made in the field of dry bulk density, using a nuclear density gage, and maximum penetration depth, using a recording cone penetrometer. In addition to good correlation between tree growth and selected spoil characteristics, the data demonstrated a gradual convergence of the measured spoil characteristic data over the study period.

Jan 1, 2008

By George Joseph Malina

Contractor chose and Owner allowed concrete to be placed using the arch first principle while excavating the 35&apos;-3" O.D. rock tunnel. The contract included excavating and lining 26,000 L.F. of rock tunnel to 33&apos;-I.D. Concrete was placed at a rate of 90LF per working day using a movable bridge to allow batching, mixing and pumping of concrete adjacent to the tunnel form.

Jan 1, 1981

By B. Pina

The conversion of maf coal to pyridine solubles and gas was investigated in a microautoclave batch reactor for two Kentucky washed coal samples (Ky. #9 and Ky. #11). Solvent hydrogen donor strength was controlled by the tetralin content of a mixed 1-methyl naphthalene-tetralin solvent. Primary liquefaction conversions greater than 90% in 10 minutes of reaction time at 427°C were achieved in liquefaction solvents with moderate hydrogen-donor strength (circa 40% tetralin). A modified irreversible first order rate expression, containing a parameter (a) to account for the intrinsic reactives of the maf coal, described the experimental kinetic data rather well. The integrated form of this rate expression is -k1e x = a (a- ß)e (eq. 1) Parameter ß in equation (I) is the pyridine solubility of the starting maf feed coal, x is the primary liquefaction fractional number of conversion, k1 is the specific reaction velocity constant and ? is reaction time. Primary liquefaction rate was found to be quite temperature sensitive and independent of coal when a liquefaction solvent containing 40% or more tetralin was employed. Primary liquefaction rate appears to depend on liquefaction solvent hydrogen donor strength for solvents containing = 40 wt.% tetralin. The intrinsic reactives in the maf feed coal or a appear to depend mainly on the inertinite group maceral content of the coal for the two coals studied in liquefaction solvents containing 3 40wt.% tetralin. In contrast, a appears to decrease in liquefaction solvents of low donor strength., i.e; solvents with less than 40wt.% tetralin.

Jan 1, 1984

By George A. Roche

Since our firm was established by Mr. Price in 1937, we have followed an investment philosophy which is based on the belief that investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria that we use to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of our investment strategy for two of the three mutual funds sponsored by the Price organization and for our private clients. However, during the past 5 years we have seen inflation accelerate due to a variety of factors including the inability of our government to meet seemingly unlimited needs with limited revenue sources. While there might be temporary periods of price stability, we believe that inflation will still continue to be the investor&apos;s greatest problem in future years. Our conviction that inflation would increase combined with the acceleration of inflation in the late 1960s stimulated an intensive investment research effort, on our part, to identify those companies with strong natural resource bases -- who own or control large, secure, and low cost tangible assets. Over the longer term and in an environment of a depreciating dollar some of these firms should be able to develop and sell these assets at higher prices. While we still believe that investing in growth companies is a sound investment strategy to offset inflation, we also believe that certain natural resource companies will show well above average investment performance. In the newest Price mutual fund, The Rowe Price New Era Fund, we have, as a matter of policy, placed a large portion of the portfolio in natural resource companies.

Jan 1, 1972

By Vince Saporito

Miners work in dangerous terrain, around the clock, with heavy equipment. Is there room for improvement in safety and standardization in the mining industry? Recent history would suggest there is a need for action. At a 2011 Spring Thaw conference in Denver CO, one speaker commented, ?We are having a number of incidents with workers getting ?pulled? into rollers or ?trapped? at transfer points when trying to manually clean (it) while the conveyor is still in motion.? It?s a troubling thought. These actions are specifically prohibited under U.S. Mine Safety and Health Administration (MSHA) regulation 57.14202. Another official from MSHA earlier this year indicated with today?s technology and policies presently in place, ?we should not be repeating the same incidents and violations year after year as we currently do.? But we are doing exactly that.

Jan 1, 2012