Search Documents

By N. E. Lehman

Cordilleran metamorphic core complexes in the southwestern United States are areas where middle to late Tertiary low-angle normal faulting has uncovered rocks that were at temperatures sufficient for mylonitization during the early part of Tertiary extensional faulting. Large-displacement low-angle normal faults that separate upper-and lower-plate rocks in metamorphic core complexes are termed detachment faults. The significance of Tertiary detachment faulting in the Basin and Range Province has only become apparent in the past 6-8 years, and the association of mineral deposits with detachment faults has only been recognized in the past few years as well. Crystalline rocks below detachment faults have typically undergone chloritic alteration and brecciation over a distance of a few to a few hundred meters below the fault surface (Fig. 1). Chloritic alteration and brecciation overprinted mylonitic fabrics formed during earlier ductile shearing along the down-dip projection of detachment faults. Rocks that underwent pre-Tertiary ductile deformation and prograde metamorphism were subjected, in rapid succession, to middle to late Tertiary mylonitization, brecciation and chloritic alteration, microbrecciation immediately adjacent to the fault, and subaerial exposure. Lower-plate rocks thus experienced rapid decompression and cooling as a result of tectonic denudation and isostatic uplift (Wernicke, 1981; Davis, 1983; Davis et al., 1986).

Jan 1, 1987

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017

By T. Johnson

Mining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel, cobalt and uranium have been particularly active. The world?s largest nickel mine ? the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale?s Voisey Bay mine in Labrador. Voisey?s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $1.4 Billion Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 ? 250,000 MT/yr manganese carbonate.

Feb 27, 2013

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By Kadri Dagdelen

Design of the ultimate pit limit to direct long range mine planning has been a celebrated problem in the mining industry, and in mining academia, since 1965. Although many papers have been presented on this topic, even today, there is not a single solution technique which is widely accepted and considered universally best. Many philosophical differences exist among the pit planners concerning the use of different methods and it appears that resistance is very strong towards accepting other techniques if you are a believer in one. Whatever the case might be, the pit parameterization technique for the ultimate pit limit design is the latest and takes a different approach than its predecessors. There are already a number of papers which discuss the concepts involved (Francois-Bongarcon, 1976; 1978; 1980; 1981); however, the aim of this paper is to fill in some of the gaps which are thought to be missing in the previous discussions and, in addition, to present the recent research done on the subject at the Centre de Geostatistique de l?Ecole de Mines de Paris in Fontainbleau, France. This paper is divided into two parts. The first part will discuss practical aspects and interpretations of pit parameterization concepts with- out using mathematical or theoretical arguments; the reader who is interested in the theory should refer to Francois-Bongarcon (1978). The second part will present an approach to obtain a complete double parameterization of reserves using an inexpensive (computer costs) single parameterization algorithm. A case study of this approach is also included.

Jan 1, 1982

By M. Botz

Alacer Gold Corporation is constructing the Çöpler Gold Mine in eastern Turkey. Mining commenced in the fourth quarter of 2009 and gold production started in the fourth quarter of 2010. The mine is a 15,500 t/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production, but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life, approximately 40 Mt of ore will be placed on the leach pad, which will contain about 35,000 t of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the life of the mine. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By A. W. Dickerson, G. Hollier, F. A. Bartley

Following on from many years of research aimed at improving the effectiveness of truck haulage operations in mines operated by BHP Minerals, BHP Research developed a concept for an Innovative Large Mining Truck, (ILMT) which has the potential to significantly improve the cost effectiveness of rear dump mining trucks. The ILMT concept reduces the empty vehicle weight dramatically, greatly reduces unequal rear tyre loading and improves ride and handling characteristics. The concept has been taken to the "proof of concept" prototype truck stage with the cooperative efforts of BHP Coal, BHP Research. Liebherr Mining Truck, Inc., Liebherr-Australia and Birrana Engineering. Testing of the prototype truck commenced at a coal mine in Queensland, Australia during May, 1996. Preliminary results from the testing program are very encouraging. Expectations are being met and in some cases exceeded.

Feb 24, 1997

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By V. J. McSweeney

This paper is directed at interested parties outside the Beach Sand Industry : the scope is quite broad. The geomorphology described is a successful working hypothesis which guided the author during prospecting and pegging campaigns : the author is not an expert in this field. The test data used in the text, for illustrative purposes, is original and may constitute a contribution to the state of the art. The operation- al and design philosophy embodied in the text is personal and describes the author's methods : all practising exponents would differ in some degree amongst themselves on these subjects. In this paper, no criticism of any existing operation or brand of equipment is intended and names are used to maintain a real contact with the subject matter. The author believes that the operational and design techniques evolved in the Beach Sand Industry under continual duress, have a wider application in the mining industry. This glimpse of the Industry is intended to enhance the respect for the present and past members. Space does not permit individual acknowledgements.

Jan 1, 1982

By F. G. Heivilin

We are no longer short of viable Rare Earth deposits. As little as 2 years ago China mined and produced 97% ofthe world?s rare earths. Only a few deposits were in an advanced stage of exploration and development. Now Technical Metals Research (TMR) Gareth Hatch *5 reports that 347 deposits are being developed by 265 companies down from 440 on July 6th. Their Index of Advanced projects lists 45 projects in 14 countries. They will sustain the world for centuries to come and many good deposits are yet to be found. The problem is mining 14 elements in balance. Each of the deposits listing production in the chart has a unique set of minerals which they think will give them a cost advantage. Which of these will make it to production is a question. Most of the Advanced won?t be mined soon, but which ones? China is still in the driver?s seat in Light Rare Earth production (LREO) with one deposit with 35 million ton Baiyunebo deposit in Inner Mongolia which is part of a working iron ore deposit. The number of HREE deposits have been reduced and they attempting to eliminate unpermitted mines. This report will tell you what a Rare Earth is, how rare they are, why they are important, and where they are being developed which includes Australia, the United States, Africa, Greenland, Brazil and Canada.

Feb 27, 2013

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014

By J. D. Miller, C. L. Lin

Filtration of fine particles involves filter cake formation and removal of surface moisture by drawing air through the porous structure. Accurate assessment of the transport properties of porous media (in this case, filter cake) is of major importance in the development of improved filtration processes. Implications from these studies are important in the design and operation of filtration equipment in order to enhance the efficiency of this important solid-liquid separation process. The microstructure and connectivity of pore space are important features necessary to describe detailed fluid flow phenomena in filter cake during fine particle filtration. In this regard, 3D characterization of pore structure is essential. The pore structure has to be described by parameters which are of special relevance to the interpretation of fluid transport phenomena. These parameters should be based on directly measured variables of the pore system and not inferred from indirect variables (such as those determined empirically from transport processes) valid only for a particular pore structure. In this way fundamental relationships between pore structure and fluid transport at the microstructure level can be described. In order to achieve this level of sophistication the three-dimensional interconnected pore structure of filter cake must be determined. Study of fluid transport phenomena in filter cake using x-ray microtomography to characterize the complex three-dimensional pore geometry is discussed. On this basis the Lattice-Boltzmann (LB) method is used to simulate and to establish a fundamental relationship between pore microstructure and effective transport coefficients.

Jan 1, 2002

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system's response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By Charles Dumaresq

The management of mine tailings poses a complex range of potential risks, including physical risks, such as the risk of catastrophic failure of a tailings facility and chemical risks such as the risk of long-term leaching of contaminants into the downstream environment. If these risks materialize, they can lead to a wide range of impacts on people and the environment, including human fatalities and severe impacts on downstream ecosystems, and the costs of recovery borne by industry, communities, governments, and society as a whole can be immense. Tailings facility failures in Canada (2014), Brazil (2015 and 2019), South Africa (2022), and in other locations around the world underscore how high the stakes are when mines produce and manage tailings (WISE Uranium Project 2019). Understandably, many people do not trust the mining industry to manage tailings responsibly. As an industry, it is our responsibility to manage tailings in a manner that is responsible and strives to minimize harm associated with tailings management, including effectively managing both the physical and chemical risks associated with tailings. Standards have an important role to play in responsible tailings management by setting expectations for standards of care and providing a means to measure and report on performance. In jurisdictions with strong legal requirements for tailings management, standards play a complementary role, pushing performance improvements in areas that may be difficult or impossible to address in legal requirements. In jurisdictions where legal requirements are lagging, standards may represent the de facto leading practice and may be the primary tool to help ensure responsible tailings management. Implementation of standards can help companies demonstrate that tailings are being responsibly managed and help build trust and credibility. Most importantly though, standards are important tools to help ensure that the risks associated with tailings are reduced, and that remaining risks are effectively managed. However, we must recognize that conformance with standards can have a down-side – the proverbial two-edged sword. Having standards is vital but there is a risk that implementing standards becomes a “box checking” exercise, with ongoing conformance leading to complacency. We must not allow ourselves to fall into the trap of believing that, just because we are complying with applicable standards and laws, we are therefore doing our best, and that “it can’t happen to us.” In addition, if conformance becomes the goal and the standard does not have mechanisms to drive continual improvement, then once the standard is met, there may be no incentive to improve. The point of complying with standards is not to pass the test. The point is to manage tailings responsibly, prevent catastrophic failures, and minimize harm. The point is to do better, because we must do better. To do that, we need to strive not for conformance, but for excellence in tailings management, driven by continual improvement and a quest to do better.

Feb 1, 2025

By Ajit Godbole, Ping Chang, Ramakrishna Morla, Purushotham Tukkaraja, Shivakumar Karekal

This paper presents the results of a study on the optimum auxiliary fan location to control air recirculation in dead-end workings where diesel-powered vehicles operate. Investigations were conducted with various secondary fan locations from the dead-end crosscut and with the intake air quantities varied using different auxiliary fans to control air recirculation and diesel particulate matter (DPM).

Jul 1, 2023