Search Documents

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013

By S. Shi, J. Y. Hwang, B. Li

Silver, copper, and zinc are commonly known elements with antibacterial and antifungal capabilities. Attempts have been made to dope silver on minerals, glass, and ceramics and the resulting materials have been investigated for their antibacterial and antifungal properties. Since silver is expensive and very reactive, silver doped materials have been found inappropriate in some applications. Copper-vermiculite is investigated as an alternative. Vermiculite has high cation exchange capacity on the magnesium ion in the crystal structure. Copper ion may have a high tendency to replace magnesium because of similar charge interference and ionic radius. Copper-vermiculite is prepared by reacting vermiculite and copper chloride solution. By impregnating copper ions into the nanometer openings between the layers of vermiculite, it is possible to render the composite with antibacterial functions if the copper ions could be released gradually from the composite. The antibacterial efficiency of Cu-vermiculite against Escherichia coli was studied using the Halo method. The results show that Cu-vermiculite is effective for preventing the reproduction of the bacteria. Heat treatment of Cu-vermiculite at up to 400°C does not show significant changes in antibacterial activities.

Jan 1, 2002

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Feb 24, 1997

By B. Caro Vargas

The Toulon South Tunnel in France is the second part of a project started 20 years ago. After the problems and delays suffered during the construction of the North Tunnel, due to a complex geologic context of highly fractured and soft rocks under a highly urbanized environment, a very dense automatic monitoring system was implemented to control the settlements of surface (more than 1000 points), the structures adjacent to the tunnel alignment and the underground galleries being constructed. The latest automatic instrumentation systems were installed, using for example AMTS capabilities in terms of ?automatic prismless settlement monitoring?. All the data (geotechnical, structural and geological) was gathered in a global automatic data acquisition system and continuously available on a web based interface. Three different threshold levels (notification, anomaly, alert) were set up, each one with a differential and an absolute value for settlements. Depending on the actual geological site conditions and the actual monitored settlements, different supporting systems and excavation techniques were used. Furthermore, the monitoring data was also used to predict and anticipate the future settlement, by comparing it continuously with the theoretical Peck settlement curves. This method allowed a better risk management by limiting the settlement on existing structures and helped to secure the Works progress schedule, for a project that lasts from July 2007 to March 2011. The implementation of this observational method application is presented in this paper.

Jan 1, 2012

By R. J. Snoby, J. K. Alderman

Although once fairly common as a method of coal preparation in the United States, dry cleaning has virtually disappeared. Low-rank coals used for power generation in the western U.S. are suited for dry cleaning because water has limited availability in the American west. Surface moisture added through wet cleaning offsets energy improvement achieved from mineral matter reduction. Information will be presented on the commercial application of dry cleaning in North America, the historic development and current status of the technology, and the introduction of modern processing theory and control technology to the design of dry cleaning equipment and plants.

Jan 1, 2001

By Steve Kral

Amax Coal Industries Inc.'s Delta Mine is a medium-sized. high-sulfur coal producer that has lived up to the challenges posed by nearly six decades of a highly competitive domestic coal market. The mine now faces one of its biggest challenges - the same one staring at the dozens of other high-sulfur producers in the Midwest - the Clean Air Act Amendments of 1990. The 59-year-old mine, located in the coal fields of southern Illinois, has remained one of the state's oldest continuously operating mines by rolling with the ups and downs of the coal market and by incorporating new technologies and innovative productivity improvements into its operation.

Jan 1, 1993

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development by Alcan of the Trombetas deposit so a general account of the Trombetas Project has already been published in E/MJ (Anon. 1975) to which the reader is referred for details on owner-ship, infrastructure and construction as well as the proposal for mining and treating the bauxite. It is impossible to consider the Trombetas deposits in isolation. A regional account of bauxite in and around the Guyana Shield and the northern portion of the Brazilian Shield is included and it is suggested that these deposits all formed during Tertiary time under similar conditions.

Jan 1, 1977

By A. Yazadni-Chamzini

Considering the nature of open pit mines, harvest volume, it usually is required to remove a lot of waste to access to mineral planned grade. So, one of the most important part of open pit mines design, is waste dump site selection. Many factors are effective in waste dump site selection. These factors are sometimes in conflict with each other. So selecting the desired location for waste dump is a process complex and multi-criteria decision making. There are a variety of methods for decision making under complicated condition, such as fuzzy, Delphi, multi-criteria decision making and Expert system methods can be hinted. VIKOR method, which is one of the decision making multi criteria methods, is useful tool for decision-making. On the other hand with regard to uncertainty in decision-making, fuzzy approach is a useful tool for this purpose. This article has tried to select the best waste dump site in Sari Gunay Gold Mine by Fuzzy VIKOR. The results show that C position has a higher priority than other positions.

Jan 1, 2012

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

The Mining Foundation of the Southwest (MFSW)promotes public understanding and education related to the mining industry. Towards this goal, the Foundation has funded several projects from donations and fundraising activities. The MFSW was incorporated in 1993 by combining the Mining Club of the Southwest and the Mining Club of the Southwest Foundation. The Mining Club began in 1971 as a social organization. It provided members of the mining community an opportunity to meet. The club also provided a means for public education about mining. In the early 1990s, the club’s efforts were directed mainly toward educational activities. And in 1992, discussions began concerning incorporation into a non-profit foundation to further the public understanding of mining. In 1983, the American Mining Hall of Fame was inaugurated to honor significant contributors to the industry and profession. The Hall of Fame serves to educate people about prominent persons associated with the mining industry, present and past. The honorees number 75. Plaques commemorate their induction and are on display at the Arizona Historical Society’s Museum in Tucson, AZ. The combined honors ceremony and banquet have remained one of the fund raising activities.

Jan 1, 1999

Caterpillar said it will produce a Cat line of ac electric drive mining trucks. The world’s largest manufacturer of mining and construction equipment said the addition of an AC electric drive truck line will provide its customers with products to fit key applications. “We are very proud of the strong leadership position that Caterpillar has attained with its mechanical drive trucks, and we will continue to invest in strengthening that position,” said Chris Curfman, president of Caterpillar’s Global Mining Division and Caterpillar Inc. vice president. “We also recognize that there are unique applications that would make the addition of ac electric drive an important and attractive complement to our current truck line.” This is the largest investment Caterpillar has made in mining trucks in its history.

Jan 1, 2006

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By Rei Arai, Yuta Yamamoto, Tetsuo Yamazaki, Naoki Nakatani

"Methane hydrate is of interest as an alternative energy resource in Japan and the R&D program has been ongoing for ten years (MH21: http://www.mh21japan.gr.jp/english/). Rare-earth element-rich deep-sea mud (REE Mud) is also of interest as an alternative resource in Japan and an exploration program has been launched in 2013.For methane recovery from the hydrate, a depressurization method pumps up water in a production well and has been successfully applied in field production tests (MH21: http://www.mh21japan.gr.jp/english/). However, micro-bubbles, which appear in the hydrate dissociation and water recovery processes may present an environmental issue. It may stick on clay and silt particles that accompany the recovered water, and may disturb settling of the particles in the water separation tank. For exploitation of REE Mud, an air-lift system has been proposed in the feasibility study (Abe et al., 2012). The same micro-bubble issue is expected during the air, water, and mud particle separation processes. In this research, the authors conducted a preliminary tank experiment for clarifying the effect of micro-bubbles on settling behavior of fine kaolinite particles. The behavior was continuously recorded by a still camera and the images were analyzed by the gray scale intensity. From the results the authors found a suspension effect for the settling of fine particles as the result of micro-bubbles. The effect should be studied in detail for preventing some serious environmental impacts during deep-sea mining."

Sep 1, 2014

By Joseph J. Diehl, Brian B. Khalighi

This paper discusses the Queens Water Tunnel, No. 3, Stage 2, being driven by a new Robbins High Performance (HP) Tunnel Boring Machine (TBM).The paper is divided into four sections. In the INTRODUCTION section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drive is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes, in the TBM OPERATION section, with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 1997

By Douglas D. Campbell, Alan S. Imrie

INTRODUCTION Mica Dam is located on the Columbia River just downstream of the "big bend" of the Columbia, where it leaves the Rocky Mountain Trench and begins to flow southwards, approximately 85 miles north of Revelstoke, B.C. (Fig.l). The dam was built as one of three Columbia River Treaty dams in British Columbia which regulate the flow of the river and provide flood control downstream in Washington and Oregon. In addition, the three Canadian dams make possible greatly increased power generation at existing power plants in the United States and further development along the Columbia and its tributaries in British Columbia. History Mica Dam, constructed during the period 1967 to 1973, is a zoned earthfill embankment 650 feet high, which has 12,000,000 acre feet of live storage and an available head of 550 feet. Power intakes which would serve either a six-unit surface or underground plant were incorporated into the design and construction of the right abutment of the dam (Fig. 2). Prior to 1971 alternative 2500 MW capacity surface and underground powerplant arrangements were studied. Cost estimates for the two alternatives were the same within the limits of estimating procedures. However, it was believed there was a certain continuing risk in locating a surface plant at the toe of a steep canyon wall. Therefore, in 1971 a tentative decision was made to proceed with an underground plant, provided that additional exploration confirmed assumptions of

Jan 1, 1976

By E. M. Hill, H. K. Lin, J. L. Oleson

When activated carbon is used for recovering gold in gold industry, carbon fine materials are generated in stripping, acid-washing and kiln regeneration circuits. The carbon fines at the Fort Knox mine, Fairbanks Gold Mining, Inc., contain up to 0.68 kg/t (20 oz/st) of gold. In laboratory tests, gold in the carbon fines was effectively transferred to coarse virgin carbon when the carbon fines were mixed with virgin carbon in cyanide solution at a cyanide concentration higher than 0.10%. A plant-scale test conducted at the Fort Knox mine also shows effective gold transfer from the carbon fines to virgin carbon with a 95% gold recovery in a two-stage gold transfer process.

Jan 1, 2002

Rising energy costs are a growing concern among mine operators. At sur’ace operations, the size of a dragline, production requirements, pit geometry and layout, and operator skill are all factors in potential energy savings. The following tips are offered as a practical means to conserve energy demand, and can be applied to diesel fuel draglines as well.

Jan 7, 1980