Search Documents

By Robert L. Hautala

In 1978, Congress established a series of mineral institutes for a limited time to assist financially in mineral industry education and research. Later, education and research were separated, establishing generic institutes for specialized research that transferred the former research budget from the base mineral institutes program. One of the generic institutes is the Mine Systems Design and Ground Control (MSDGC). It provides for research funding specifically for mining. Other parallel generic institutes were established in pyrometallurgy, comminution, waste management, etc. MSDGC was established at Virginia Polytechnic Institute and State University(VPI). The founding group included the University of Alabama, University of Kentucky, University of Nevada Reno, University of Idaho and University of Alaska reporting through VPI to the US Bureau of Mines (USBM) and Congress. Other universities also participated on an ad hoc basis.

Jan 1, 1996

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, Mari Lundström, Eero Kolehmainen

With decreasing ore grades, the tailings of mining operations are becoming of increasing interest as metal-containing secondary raw materials. The objective of the current work was to investigate chloride leaching of gold, copper, cobalt, nickel, and zinc present in the flotation tailings. In the current study, the effect of cupric ion as an oxidant (0–50 g/L) and NaCl (150–250 g/L) on metals extraction was investigated. The other parameters, such as pH (1.8), temperature (95 °C), solid/liquid ratio (25%), oxygen feed rate (1200 mL/min), leaching time (24 h), and stirring rate (950 rpm), were kept constant. Gold dissolution rate was shown to increase with increase in cupric ion concentrations up to 50 g/L. Also, increase in NaCl concentration up to 250 g/L increased gold extraction. Majority of the copper present in the flotation tailings could be dissolved with all the all solutions investigated. The other base metals, cobalt, nickel, and zinc extractions were also shown to increase with increase in the cupric ion and sodium chloride concentration. However, even in the absence of cupric ion addition (t = 72 h, 250 g/L NaCl), the final extraction of Cu, Ni, Zn, Co, and Fe increased up to 98, 93, 83, 76, and 80%, respectively. This shows the power of inherently originating oxidants present in the tailings. Furthermore, the solid analysis of the leach residue indicated that leaching the flotation tailings in pure NaCl may result in partial gold dissolution. The results demonstrate that significant amount of metals present in the tailings could be extracted even with only NaCl as added chemical in the presence of oxygen feed, oxidizing agents originating directly from the raw material. This can provide an advantageous cyanide-free method for extraction of metals from very low-grade tailings with low chemical consumption.

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump's best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"' BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981

By Donald D. Murphy

My first contact with underground, bolt conveyors came when I was hired as a draftsman by the La-Del Conveyor & Manufacturing Company in 1935. At that tine relatively few nines were using haulage belt conveyors. Wore they were in use, they were usually loaded by chain or shaker type room conveyors which in turn were hand loaded at the working face. Duo to the low room tonnage, a gathering belt might receive who output of from six to eight rooms. For several years belts 26 and 30" in width were the favorites for coal mine use. Belt speeds very seldom exceeded 200 ft. per mm. at that time. Conveyor lengths for the majority of units lay between 1.000 and 2000 ft. For a number of years 25 H.P. drives were adequate for those conveyors. From 1940 until about 1950 loads and speeds went up slightly and 40 H.P. drives became the standard. Since the majority of mines were then using direct current power systems, we were able to use controllers with 3 or more steps of starting resistance. The slow belt speeds coupled with relatively long starting cycles kept the rate of acceleration low and gave us smooth, easy starts.

Jan 1, 1963

By Bruce D. Hansen

For many years, Newmont has focused on improving its operations. After the merger between Newmont and Santa Fe Pacific Gold, Newmont created synergies of more than $50 million a year in Nevada. This was done primarily through optimal ore movements and consolidation of various functions. During the current period of low gold and copper prices, Newmont has refocused its efforts on efficient operations worldwide. At its mine facilities in Nevada, Newmont has used a combination of several strategies to decrease the costs of operations and to increase profitability. These include computer technology, optimal use of infrastructures, procurement strategies, functional consolidation, enhanced mine planning and several available metallurgical processing options.

Jan 1, 1999

By R. Hipsley, D. Arbonies, P. Dobak

South Arturo is a “Carlin-type”, breccia-hosted, oxide gold deposit located at the north end of the Carlin Trend. The discovery hole was drilled in July 2005 from mine dumps 1,000 feet south of the Dee open pit. Discovery hole (BD-72) encountered a cumulative 245 feet @ 0.056 opt Au beneath 850 feet of post mineral Tertiary Carlin Formation. Oxidation extends to depths greater than 2,000 feet in the deposit area. The deposit is presently in definition drilling stage with approximately 190,000 feet of drilling completed to date. A resource estimate is in progress. This paper will focus on the discovery and descriptive characteristics of the mineralization.

Jan 1, 2007

By L. B. McConville

The general term "tar sand" has been used to describe sand containing varying amounts of dense, viscous petroleum. Deposits of tar sands have been found throughout the world, often in the same geographical area as conventional petroleum. The largest one by far is known as the Athabasca Tar Sands, and is located in the province of Alberta, Canada. Actually a group of three deposits, these particular sands underlie an aggregate area of more than 12,000 square miles. Current estimates place the contained raw petroleum at about 700 billion barrels, from which as much as 300 billion barrels of synthetic oil may be recoverable under presently developed technology. For comparison, this latter quantity is roughly equivalent to five times the combined total of U.S. and Canadian crude oil reserves. With the ever-widening gap between energy supply and demand, attention is being directed to all possible energy sources - both developed and underdeveloped - and certainly the Athabasca Tar Sand deposit is one of the more important ones to merit such attention. This paper will review some of the more significant developments and attempt to place in perspective the role that this source of energy could possibly be expected to play in the foreseeable future.

Jan 1, 1974

By Betty L. Gibbs

Using a PC can help an operator analyze data more effectively and respond quickly to changing conditions. The cost of microcomputers is low, and fit into the budget of even small mines. Many software packages are also low cost and general software such as spreadsheet, word processing, and data base management programs can help the small miner organize and evaluate information very quickly. A basic hardware configuration is proposed, including hardware upgrades and general and technical mining software packages. The hardware and software suggested can be used by very small as well as larger operations. PC's can be incorporated into all phases of a mining operation at a minimal cost and capabilities can be expanded as the operation grows.

Jan 1, 1987

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By Paul L. Russell

Interest in the western oil shales of the US began in about 1908, with the first retort in Colorado constructed in 1917. The most successful early developments were near Elko, NV, where the Catlin Shale Products Co. produced more than 1.9 dam3 (12 000 bbl) of shale oil during 1920-1924 and at Rulison, CO, where a US government operation produced about 570 in 3 (3 600 bbl) of shale oil during 1926-1929. Plentiful low-cost crude oil was developed about this time and shale oil was of little or no interest until after World War II. From 1944 to about 1972, several companies, and the US government, operated shale oil mines and recovery plants in Colorado. While technical successes were achieved and an estimated 40-56 clam' (250 000-350 000 bbl) of shale oil were produced, economics were not favorable and commercial production was not achieved. In recent years domestic production of crude oil supplies has not kept pace with US consumption. The growing shortfall has been met with imports. The cost of imported oil has continued to escalate and increased US dependence on petroleum imports are national concerns, because of the negative impact on US balance of payments and an increasing dependence on other nations for US energy needs. In 1978, petroleum imports equaled about 44% of demand, up from 23% in 1970, but down from 48% in 1977 because of availability of Alaskan North Slope crude oil. Reduced domestic consumption and other factors have reduced current imports to about 40-45% of de¬wand-but at ever increasing cost. The growing shortage of crude petroleum and its increasing cost have resulted in renewed worldwide interest in oil shales. In the past, the main obstacle to oil shale development (progress toward commercial production) has been economics-shale oil cost too much to develop and thus could not compete with conventional petroleum crudes. Even with today's inflated energy prices, some experts say the production of synthetic crude oil from oil shale is, at best, marginally economic. The 1973-74 Arab oil embargo and increased crude oil costs-along with the federal government's offer to lease oil shale lands-resulted in renewed

Jan 1, 1981

By J. H. Meza Viveros

This paper describes some actual parameters and technologies used at Mexicana de Cobre Smelter, and the principal design parameters and new technologies which wiil be used with the smelter expansion project, in order to increase the production capacity of anode copper from 180 000 mtpy to 300 000 mtpy. Likewise its describe some parallel projects under construction also in the smelter plant.

Jan 1, 1997

The National Mining Hall of Fame will induct five mining greats on Saturday, Sept. 17, 2005 at the Museum Convention Center in Leadville, CO. The 18thAnnual National Mining Museum and Hall of Fame Induction Banquet will begin with an open house and reception at 5:30 p.m., followed by the dinner and program at 7 p.m. The five inductees are Nathaniel Peter Hill, John Munro Longyear, John McDonald, Julius Eckhardt Raht and John Dennis Ryan. Nathaniel Peter Hill (1832-1900) built the first successful smelting operation in the Rocky Mountains in1867 at Black Hawk, CO. From 1879 to 1885, he was a U.S. senator. He also taught courses at the Colorado School of Mines.

Jan 1, 2005

By Donald R. Williamson

The Cyprus Pima Mining Company's open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. At that tine reserves were law - volume (+10 million tons) and high grade (+1.5% Cu). Several periods of growth have brought the operation to its present production level of 55,000 tons per day of ore and +125,000 tons of waste. Over the years, a number of attempts to refine and polish the ore reserve figures have been made using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Other refinements were tried using adaptations of established methods combined with computer modeling techniques. The resulting mine-model ore blocks were an improvement but they still tended to show too match tonnage of mill feed, often at too low a grade. One attempt at Kriging had only limited success. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons thus far between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results. A new, better procedure for estimation of ore reserves apparently has been developed for the Cyprus Pima deposits. The specific procedures seem likely to have direct application to other, similar operations. The methods used to develop the procedures could be of value to still other operations.

Jan 1, 1976

By D. J. McCracken

During 1995, the estimated consumption of lithium minerals in the western world was 139 kt (153,000 st).This amounted to 18 kt (20,000 st) of lithium carbonate equivalent (LCE). Overall tonnage demand for lithium minerals increased by 10.8 kt (11,900 st) during 1995from 1994. From 1992 to 1995, overall tonnage demand has increased 62%, from 85.5 to 139 kt (94,240 st). There are four major producers of lithium minerals. Gwalia Consolidated in Western Australia is the largest producer of spodumene. It supplies high-grade spodumene concentrate, fine-spodumene concentrate, glass-grade spodumene and chemical-grade spodumene.Tantalum Mining (Tanco) of Manitoba, Canada, produces high-grade spodumene concentrate, fine-spodumene, concentrate and montebrasite. Bikita Minerals in Zimbabwe is the largest manufacturer of petalite. It supplies high-grade and container-glass petalite.

Jan 1, 1996

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring, system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's design philosophy, hardware and software components, examples of installations, and a few observational results.

Jan 1, 2002

By Levent Ozdemir, Robert J. Evans, Russell J. Miller, William Sharp

This paper describes the specifications and capabilities of a 6 ft (1.83 m) diameter laboratory rotary cutting machine which was designed and fabricated under a Bureau of Mines (USBM) contract awarded to the Colorado School of Mines (CSM). The machine will be used for carrying out research and development programs aimed toward improving the design and operation of mechanical tunnel, raise and shaft boring equipment.

Jan 1, 1983

By B. Valentim

The methodology used to obtain fly ash subsamples of different sizes is generally based on wet or dry sieving methods. However, the worth of such methods is not certain if the methodology applied is not mentioned in the analytical procedure. After performing a fly ash mechanical dry sieving, the authors compared those results with the ones obtained by laser diffraction on the same samples and found unacceptable discrepancies. A preliminary study of a wet sieving analysis carried out on an economizer fly ash sample showed that this method was more effective than the dry sieving. The importance of standardizing the way samples are handled, pretreated and presented to the instrument of analysis are suggested and interlaboratory reproducibility trials are needed to create a common standard methodology to obtain large amounts of fly ash size fraction subsamples.

Jan 1, 2008