Search Documents

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By Gary E. Slagel

The year was 1974. The event - the United States Congress was embroiled over what issues should be included in the proposed national surface mining law. The question - what should be done with underground mines? The leading bills ultimately addressed the environmental impacts associated with underground mines including provisions to protect the surface from subsidence impacts. Amid the fears that this subsidence language might discourage underground mining, sponsors of the bill were asked to explain the meaning of the provision that read "to prevent subsidence to the extent technologically and economically feasible." Was this an attempt to limit mining that caused planned and controlled subsidence? Former Deputy Director of the Office of Surface Mining, Dean Hunt, reviewed some of these historical events in a 1985 presentation before the Eastern Mineral Law Foundation. He reported that in 1974 Congressman Morris Udall took the floor to respond to these concerns expressed by other members of Congress and the industry. Mr. Hunt cited Congressman Udall's July 10, 1974 Congressional Record statement: "The House bill contemplates rules 'to prevent subsidence to the extent technologically and economically feasible.' The word prevent led to fears expressed by the Secretary of the Interior Morton, that the effect would be to outlaw longwall mining, with its obvious subsidence ... in fact the bill's sponsors consider longwall mining ecologically preferable and it and other methods of controlled subsidence are explicitly endorsed." Further, the report that accompanied the front-running bill, HR11500, provided the following clarification on the issue of subsidence prevention: "It is the intent of this section to provide the Secretary with the authority to require the design and conduct of underground mining methods to control subsidence to the extent technologically and economically feasible in order to protect the value and use of surface lands. Some of the measures available for subsidence control include: (1) leaving sufficient original mineral for support; (2) refraining from mining under certain areas---or (3) causing subsidence to occur at a predictable time and in a relatively uniform and predictable manner. This specifically allows for the uses of longwall and other mining techniques which completely remove the coal." It is clear from the preceding statements that Congress considered the removal of all the coal and causing subsidence in a predictable and uniform manner to be equal to or better than leaving support coal and causing no subsidence. While the actual provision in the bills talked of preventing subsidence, a subsequent exception made it clear that the real intent was to control it. This is evidenced in the specific planned subsidence language that appeared in the bills and ultimately in Section 516 (b) (1) of PL95-87, the Surface Mining Control and Reclamation Act. It reads: "...adopt measures...to prevent subsidence ... except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." In spite of this historic record that supports controlled subsidence, something has been lost in the implementation. The primary focus by many regulators over the past few years has been on the "prevent" aspect irrespective of mining method being used. This has appeared to change the original intent of Congress from one of controlling subsidence to one of minimizing damage. The objective of this report is to review some of the current regulatory issues that impede full extraction mining and offer some suggestions on possible ways to deal with these issues.

Jan 1, 1986

By W. L. Garrison

Improvements continue to be made in rapid excavation and tunneling technology. There are several ways to examine the impacts of such improvements. The most common procedure is to monitor current developments and to evaluate prospects for expansion of present types of uses. Other approaches are called for, however, if the technology might be used in ways not now imagined, if the search is for information for managers of technology development, and if the issue is that of the wise use of the technology by society. The first section of the paper will pose these matters as questions. These questions will be examined from the point of view of the processes of technology development and utilization, and then further examined against the backdrop of processes at work within the urban area. Such an examination will provide insight into the way technology developments should proceed. The final section will present some comments that may be useful to those guiding the development of the technology and to those who might provide leadership for its wise utilization. THE QUESTIONS Three questions are posed: 1. Are there uses for the technology beyond further penetrations of its present markets? 2. Can information be supplied to managers of technology development so that they may improve the assignment of priorities among development choices? 3. How can society make wiser use of the technology?

Jan 1, 1974

Let’s start off with your assessment of the mining industry. Today, the status of the mining industry is stronger than it has been over the previous few years. While mining continues to be a major part of the world’s economic foundation, the industry is gaining strength due to rebounding metals and minerals prices. And now, with these rising prices and the changes the industry instituted during the years when mining-related commodities were selling at low prices, our stronger, more productive and internationally competitive industry should flourish. Mining remains an essential business and the industry is far ahead of the game when it comes to the trend of globalization as a key to sustained growth. Also, the industry continues to realize increased productivity through technological innovations. And an increasing number of countries are moving towards capitalism, which opens doors for exploration and mining within their borders. After looking at all of these factors, I believe that the mining industry will only continue to gain momentum in the future.

Jan 1, 2004

By E. Z. Casassa

There has been a recent revival of interest in concentrated coal/water slurries as a substi¬tute for fuel oil or for coal/oil mixtures, particularly in electric power generation. The idea is not a new one. Coal/water slurries were transported by pipeline in the U.S. in the early nineteen-sixties, and the Black Mesa coal pipeline has been in operation for several years, while in Germany, coal/water slurries were being burnt for power generation in the early nineteen-seventies, as described by Merten and Höner (1972). Since coal is not a pure substance but a carbonaceous mixture, the different chemical and physical behavior of coal/water dispersions from different deposits must be understood in order to optimize the properties of the result¬ing slurry fuels. Since minerals which are minor constituents of coal may also strongly affect slurry properties, coal chemistry may vary considerably even within a single deposit. Thus it is unlikely that there will be a single formula for optimizing the slurry properties of all coals, and even the answer for coal from a single source may change with time.

Jan 1, 1983

By John Kinneen, Sunghoon Choi, Arne Fareth, Edward S. Barboe, Kyle R. Ott

A new water treatment plant is to be constructed for a portion of the water supply system of New York City. The project includes construction of new water conveyance tunnels crossing perpendicular and sub-parallel to the existing pressurized water tunnel at two locations. A study was conducted to evaluate the impact of new tunnel construction on stability of the existing tunnel and hydrojacking potential in the surrounding rock mass. This paper introduces a practical approach to evaluate tunnel interaction, expressed in terms of rock-liner interaction, stress-induced stability and hydrojacking failures. A simple method to evaluate hydraulic and mechanical properties of concrete liners and jointed rock mass is also presented.

Jan 1, 2007

By G. Kosick, G. Dobby

CEET, an acronym for Comminution Economic Evaluation Tool, was jointly developed by MinnovEX Technologies Inc. and 13 major mining companies for the purpose of designing and predicting the performance of grinding circuits. It fundamentally differs from other methods by using as its’ data set a geostatistically significant population of hardness data distributed across the mine block model. Historically the characterization of an orebody for the purpose of either designing a grinding circuit or predicting the performance of an existing circuit has been done with a relatively limited number of discrete samples. In addition to power selection, shell sizing, and costing for multiple circuit options, CEET also outputs tons per hour, P80, and operating cost on every mining block for subsequent integration back into the block model. This paper will provide an overview of what CEET is and how it works.

Jan 1, 2001

By Steven K. Duke, Jay Arabshahi

An economic, real-time probe drill monitoring system was developed for Metropolitan Water District’s Arrowhead Tunnels project to quantitatively evaluate ground conditions ahead of a TBM. This system digitally records hydraulic feed, rotation, and percussion pressures and calculates drill advance rates during drilling. These data are computer synthesized to develop a digital representation of the ground ahead, and the resulting “picture” of the ground is distributed to the project team to assist with tunnel construction decisions (i.e., targeting grout holes, optimizing mine-cycle lengths, and avoiding becoming stuck). The analysis and interpretation procedure has now been calibrated and refined using over 5,000 m (3 miles) of geologic face mapping data.

Jan 1, 2007

By John E. Shively, Tracy K. Lundin, Francis Fong

The Superconducting Super Collider (SSC) features two 20 TeV counter rotating proton beams which will be housed in 87 km (54 miles) of tunnel. Four additional lower energy particle accelerators will be housed in 26 km (16 miles) of tunnel and underground structures. Physics experiments will be conducted in two underground detector halls approximately 67 m (220 feet) deep with footprints measuring about 30 m (100 feet) by 100 m (330 feet). Definition and design of underground facilities is advanced with construction of approximately one-third of the SSC program underway. This paper presents an overview and status of the SSC project.

Jan 1, 1993

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

By David E. Thompson, Andrew F. McKown, Herbert H. Einstein, Amr S. Azzouz

INTRODUCTION Design of supports for underground chambers in rock has undergone considerable development. This becomes evident when comparing support dimensions of subway station caverns built in the U.S. over the past fifteen years. The Porter Square Station cavern, which is a part of the Massachusetts Bay Transportation Authority (MBTA) Red Line extension, is the latest in this series. It is approximately 168 m (550 ft) long, 21 m (70 ft) wide, and 14 m (45 ft) high, and has a permanent support of light steel ribs imbedded in a 0.4 m nominal (15 in) shotcrete lining. An extensive construction control instrumentation program made it possible to evaluate the performance of the cavern and its support. This evaluation, which is presented in this paper, was the objective of a research project sponsored by the Urban Mass Transportation Administration (UMTA) and jointly conducted by Haley and Aldrich, and MIT. The actually used design procedure was compared with other approaches, notably procedures based on Finite Element analyses and empirical rock mass classification methods. Support dimensions predicted with all these approaches were compared to the actual support and its performance.

Jan 1, 1983

By K. Hanson

When done properly, benchmarking is an extremely effective tool for assessing ones performance, finding areas for improvement, and identifying strengths. However, when done improperly it can be an exercise in futility and result in incorrect observations and conclusions. A primary pitfall of benchmarking is collecting too much unreliable information. Surprisingly, the evolution of data storage and the ease of data collection are not helping with better data collection. Instead, it is just allowing one to collect more information, while at the same time inundating one with too much data. Additionally, the process of data collection can be tedious and is often times delegated to the least experienced individual resulting in unreliable and incorrect data collection and entry. Another primary pitfall of benchmarking is metrics that are cost based or poorly designed. Cost based metrics typically involve comparing unit mining costs ($/tonne). Between mines, unit mining costs are not very well correlated and have become further complicated by significant regional cost variations and mining inflation in the last years. Likewise, poorly designed metrics lead to poor benchmarking results. Examples of poorly defined metrics include: metrics that rely on information that is difficult to collect, metrics that are poorly defined, metrics which are too site focused, and metrics that measure low consequence practices.

Jan 1, 2011

By T. Weatherwax

As part of a strategic research initiative at UBC to design and evaluate integrated underground mining and mineral processing systems, work has been done to determine how to utilize the coarse rejects of pre-concentration in the underground environment. An amenability study for nine orebodies from four of Xstrata Nickel?s Ontario operations evaluated both processing and waste disposal methods. The utilization of the rejects as a high quality backfill with minimal binder requirements has been identified as the preferred disposal method. Fill mixes utilizing the rejects in combination with classified tailings, full tailings, and cement were developed based on the geotechnical properties of the rejects. The mix designs were examined for both strength and rheological properties. The paper will present the results of the pre-concentration testwork, the design and strength testing of various mix designs for rejects from the nine ores and presents a conceptual design for an underground pre-concentration system based on this test work.

Jan 1, 2008

By Jamal Rostami, Manso Deen Sesay, Sydney Slouka, HUGH MILLER, Anshuman Mohanty, Midhat Sajad, Kun Zhang

The lack of progress in controlling pulmonary diseases such as pneumoconiosis cases in recent years necessitates additional studies on dust generation and the characterization of airborne dust. Studies are underway by a NIOSH-sponsored project to observe the characteristics of the dust generated by pick cutters under various wear levels. This research performed a full-scale linear-cutting-test matrix on eight coal samples with various bit penetrations, spacing, and wear conditions. The specific energy and resulting PSD (particle size distribution) of airborne dust and material left at the cutting surface were measured and analyzed. The dust concentration was determined using the NMAM (NIOSH Manual of Analytical Methods) 0600 method. For fines, the PSD was characterized using Laser Diffraction, measuring percent channel and aerodynamic diameter, while Imagej, a virtual sieving application, was used for larger particles. The results show that for a new bit, as the cutting depth and spacing increase, the specific energy and dust generation decrease. The size and shape of the dust particles have been analyzed, and the observed trends are discussed in this paper.

Feb 1, 2025

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This article offers an examination of a retreat mining method conducted at the Pinoura Mine in India from 2010 to 2017. The method is atypical for coal mines of India’s coalfields. The method executes depillaring in a single pass and does not require the formation of galleries and support installation in splits, thus, reducing the cycle time. A variety of observations are discussed throughout this work and emphasis is placed on field measurements and depillaring under weak roof (RMR = 40–45). This paper discusses design techniques, specifically the estimation of the snook (remnant pillar) size, and important practical observations after the fact. The execution of this method was eventually conducted in eleven panels.

Aug 4, 2020

By Charles L. Allie

Since Reserve Mining Co. began commercial operations at Silver Bay, MN, some 25 years ago, major improvements in taconite processing technology have become available. In addition, significant new government standards have been imposed on industrial operations. By implementing a $370-million modernization program, Reserve was able to accomplish two major company objectives: the quality of concentrates produced from the Peter Mitchell mine has improved, and the operation meets both present and foreseeable environmental standards. Process modifications at Reserve were designed to: •Reduce the pellet silica content from 9% to 5%; •Increase the pellet iron content from 62.5% to 65.8%; •Implement a tailings disposal system utilizing "best available technology" water quality controls; and •Reduce air emissions by installing "best available technology" air emission controls. By adding dry cobbing, fine screening, and flotation to the concentrating process, pellet silica content has been reduced; the process reclaims and reuses all process waters; all tailings are stored in a zero discharge tailings basin; and all air emission standards are being met. Initial Beneficiation at Silver Bay Reserve's Peter Mitchell mine at Babbitt, MN, is on the eastern end of the Biwabik iron formation. The open-pit mine is approximately 16 km long, 0.8 km wide, and presently has a maximum depth of about 50 m. Principal constituents of the ore body are magnetite, quartz, and iron-magnesium silicates. The company's large commercial plant began operating at Silver Bay, 75 rail km from the mine, in 1955. Facilities have historically had the capacity to process 31.5 Mt/a of taconite, containing an average 24% magnetic iron, into 11 Mt/a of iron ore pellets. Reserve's initial beneficiation process-which existed up to early 1979-consisted of two crushing stages at the Babbitt mine site, two additional crushing and screening stages at Silver Bay, grinding in a conventional rod-ball¬regrind mill circuit, size classification with cyclones, and concentration with magnetic and hydraulic separators. Concentrate produced by that circuit assayed 65% iron and 8.5% silica, with a screen analysis of 94% -44 µm, and a surface area of 9300 cm2/cm3. Pellets produced from this concentrate assayed 62.5% iron and 9% silica (dry basis). Construction began in 1977 to modify Reserve's operation. Process modifications were designed from pilot scale operations that had been operated and researched by Reserve for more than 10 years. There were two design restraints imposed on the process: economic constraints that Reserve continue to use much of the existing processes and structures in the new operation; and a substantial number of government-imposed permit constraints. In effect, the tailings process was designed first and then a concentrating process was developed that would "fit" the tailings disposal system. Operation of the modified process began in June 1980. Crushing Remains Unchanged No changes in process flow were made at either the Babbitt mine and crushing plant or at the Silver Bay fine crusher. Gyratory crushers reduce run-of-mine taconite to -90 mm-diam at the mine. Taconite is then transported to Silver Bay by intra-plant railroad. There are 10 fine crushing lines. Each consists of a double deck screen, followed by a heavy duty short head crusher, a second double deck screen, and second short head crusher. All screen undersize material bypasses the crushing lines, resulting in an open circuit crushing process. Fine crusher product is approximately 98% - 20 mm, 80% -12 mm, and 50% -10 mm in diameter. Each fine crusher line processes about 400 t/h of crude taconite. Cobbing Provides Aggregate for Tailings Dams The first major process change was the addition of dry cobbing, a dry magnetic separation step between the fine crusher and concentrator. Dry cobbing serves two major purposes in the new process. Its principal function is to provide large volumes of dry coarse aggregate for use in construction of tailings dams. This process rejects about 20% of the fine crusher product as tailings with a size analysis of 98% -20 mm and 50% - 10 mm. These tailings are free draining and have high frictional shear strengths-two key requirements for dam building aggregates. Fine crusher product is conveyed to a new dry cobbing building. Here crushed ore is discharged into one of two 30-minute capacity surge bins. Crushed ore is withdrawn by 12 constant speed conveyor belts; each discharges 500 t of crushed taconite into a dry cobbing machine. Each machine consists of a 3-m-long riffle splitter and two vari-

Jan 12, 1980

By Priscilla P. Nelson

Many concepts concerning equipment selection, performance prediction, and evaluation of support requirements for tunnel construction in soil or hard rock tunnels cannot be extrapolated directly for application in soft rock (compressive strength between 1.0 and 35.0 MPa). Case histories for small diameter (less than 3.5 m) tunnels in Austin, Texas, are analyzed to gain insight into particular problems encountered during tunnel excavation in weak sedimentary rock, and the performance of different excavation systems are compared.

Jan 1, 1987