Search Documents

By B. Z. Weiss, N. R. Comins, F. Blum

The effect of microstructure on the deformation and fracture properties of 3CR12 steel was investigated at different strain rates in the temperature range -196 to 200°C. The yield stress of the as-received steel, showing a banded dual-phase microstructure, was much lower than that of the flake-like dual-phase microstructure produced by heat treatment. The heat treatment also resulted in an increase in the volume fraction of martensite. The fracture toughness of the as-received 3CR12, on the other hand, was significantly higher than that of the heat-treated material. These changes in both yield stress and fracture toughness were attributed to the effect of microstructural parameters on the constraints imposed on the deformation and subsequent failure of the ferritic phase in the as received and heat-treated steels. The exceptionally low resistance to crack extension in a plane parallel to the roiling plane of the as-received material was ascribed to the delamination process, which is typical for controlled-rolled steels. The yield stress and fracture toughness were found to depend on temperature and strain rate. The appearances of the fracture surfaces were found to be consistent with the mechanical properties.

Jan 1, 1992

By D. Pienaar, D. Stanton

This paper provides an overview of possible approaches for structuring the ventilation systems for mines that will become operational within the next decade. Features addressed in the paper include: aspects of airway design and layout in the absence of centralized vertical return shafts, the impact of using diesel-powered trackless equipment in conjunction with conveyor belts in the development and production phases of the project, and the need to balance increasing electrical power costs against the requirement for reduced capital expenditure. The paper provides brief descriptions of the strategies employed in real-life situations and presents an overview of various operational parameters affecting the design of ventilation systems that will be used as ?platforms? for much deeper mines in the future.

Jan 1, 2006

By H. W. Read

The South African platinum industry finds itself in the midst of a rapidly evolving society that is no longer characterized by the apparent stability of the previous decades. The features of this society include increasing global competition, rapid technological innovation, a declining skills pool, major political transformation, a more challenging working environment as the mines reach deeper into the earth?s crust and a greater concern for human welfare. It is therefore axiomatic that new ways will have to be found to engage the all-pervasive change in the mining environment. Although in general terms project management is a universal endeavour for managing change, it takes place in a specific socio-techno-economic environment and geographical setting that gives it a particular context. The argument of this paper explores, analyses and synthesizes the impact of these changes on the emerging project management methodology. In essence, the management of change will inevitably contribute to the emergence of new dilemmas, issues and challenges. The change management process and procedures will also be affected by this change and in response, drive internal change of its own structures and organization. And, therefore, a new paradigm of project management will become apparent. A new project management model will then be proposed to the industry.

Jan 1, 2006

By P. T. Slatter

The role of viscometers for rheological characterization in the hydraulic transport of solids is discussed, and rheological models and phenomena pertinent to the hydraulic transport of backfill material are reviewed. The two main branches of viscometry (rotational and tube) for the measurement of mining slimes rheology are compared. The effects of solids concentration, particle size and chemical additives and the practical application of rheology in backfill system design are presented.

Jan 1, 1988

By G. Ferrara

The mathematical framework of a well-established model proposed earlier by the authors for the screening process is briefly recalled. Some numerical methods for the application of the model, concerning numerical solution of the equations and parameter estimation, are indicated. Some applications of the model to improve screening operations, sizing of screen, simulation of screening and of integrated plant operations are discussed, and the computer software to be used for these purposes is described in detail.

Jan 1, 1987

By P V. Savage, T Glück, RCA Minnitt, C Bothma

Manganese Metal Operations ?Manganese Metal Company (MMC), a subsidiary of Samancor BHP Billiton, has two production facilities for electrolytic manganese metal in South Africa and produces a range of about 44 Mn metal products. ?The company is accredited with ISO 9000 and uses Six SigmaTM for continuous improvement. ?The control of the process relies on the effective functioning of approximately 250 different control loops at 50% automation.. ?Approximately 50000 samples are analysed every month. ?There are pyro, hydro and physical unit operations for the production of electrolytic manganese metal flake and value added products ? [ ]

Jan 1, 2005

By R. Yi

The determination of the optimum cutoff grade for a surface mine may be very different from that of an underground mine because a selectable mining method may be used in the latter case. A review of research into the theory of cutoff grade is made and then a new method, based on Optimal Control Theory, is presented. This method uses a Hamiltonian function to assist in obtaining the solution. It is shown that the life of a mine can be divided into three parts: a beginning period bf planning before mining; an intermediate period when both an average price and market information are used continually to adjust the cutoff grade; and, a final period when the main consideration is the current market situation.

Jan 1, 1987

By C. L. de Jongh

The number and scale of backfilling operations in the South African gold mining industry have grown rapidly in recent years. The application of backfilling as a means of stope support in a wide range of geological conditions and mining systems has resulted in the development of a variety of alternative fill systems. Experience gained in the evaluation of operating fill systems has contributed to a knowledge of the essential concepts to be considered in their design. This knowledge can also influence management's perception of what is expected of a backfilling system. The factors to be assessed in stating and satisfying these objectives are examined. The areas of investigation cover the selection of a suitable material, its preparation, distribution and placement, and the engineering logistics involved in the management of such a system. Finally, the integration of a filling system with an existing mining operation is examined.

Jan 1, 1988

By J. Lamb

Project managers must juggle many aspects to bring their project in on time, on budget, and in accordance with the aims of the project owner. Whether the project is a mining feasibility study, a technology implementation or a construction project, it falls to the project manager and his or her team to deal with risk from two standpoints, which may be at odds with one another. First, a project team must deal with risks to the project itself - that is, risks to on-time, on-spec and on-budget delivery against the value promise made to the customer. Second, there is the management of risks within the subject matter of the project, undertaken on behalf of the customer. The project manager cannot dodge this responsibility; yet there is a tendency (particularly in smaller, in-house studies) to avoid digging too deep, possibly for fear of what may be uncovered! This paper investigates the responsibilities of project teams in regard to risk management and reporting. It examines ownership of project risk; the nature of risk management activities undertaken by the team during the course of a project; and outlines some controls to ensure that the two opposing arms of project risk are reconciled for the benefit of both the project team and the project owner.

Jan 1, 2007

By D. P. Enright, D. D. Howat

Austenitic manganese-steel castings are very widely used in crushing and grinding in the' gold-mining industry in South Africa, The service life of a casting in a short-head crusher is difficult to predict because there are no clear-cut criteria by which such a judgement can be made, The addition of molybdenum and zirconium to the castings for crushers failed to result in improved performance, The results of extensive tests with through-hardened steel castings were very disappointing, mainly because of a design factor in the bowl liner. The design of the bowl liner is an important determinant of the life and performance of these castings. The extent to which the material in a crusher is reduced in size has profound effects on the consumption of metal and power, and on the effective life of a casting. Tests on manganese-steel castings in an 8 ft by 12 ft rod mill provided data on the total consumption of metal, and on the variations in the pattern and rates of wear of liners over lengthy periods. Progressive changes in the wear profiles of the lifter bars and the other liner components showed unexpected features. There are clear indications that, whereas a set of lifter bars will at first lift the charge strongly with relatively little slippage, there is a later period characterized by more slippage and greater wear on all the liner components.

Jan 1, 1980

By N. J. Alderman, R. Haldenwang

Flumes are ubiquitous throughout the mining and minerals processing industries as well as being used in the polymer processing and pulp and paper industries. With the increased demand for the transport of highly concentrated slurries in rectangular open channels, there is an impetus for a better understanding of the role of rheology in flow hydraulics. Until recently, design of such channels has been based on either the Chézy or Manning equations used for modelling open channel flow of Newtonian fluids. This has been done for modelling turbulent flow of low concentrated slurries with some success. However, this is not the case for highly concentrated slurries where the flow in the channel is no longer turbulent. Unlike Newtonian fluids, work carried out on flow of pseudo-homogeneous, non-Newtonian fluids in open channels is somewhat limited. Moreover, these results have been published in a variety of sources. This paper attempts to give a critical review of the work carried out on Newtonian and non-Newtonian flow of pseudo-homogeneous non-settling slurries in rectangular open channels. A comparison is also made of the models based on power law, Bingham plastic and Herschel-Bulkley fluids for laminar and turbulent flow in rectangular open channels.

Jan 1, 2007

Orebody modelling and reserve estimation are now subject to sophisticated procedures, but folded stratiform and stratabound deposits present particular problems in transforming coordinates of samples and blocks into their correct relative positions prior to deformation. In this paper an approach is taken whereby a geologically interpreted reference plane is used as a control. The study area is the Rio Tinto Minera copper mine near Santiago de Compostela, Spain. The transformation procedure on the 'unfolded' state is described, its limitations assessed and advantages considered.

Jan 1, 1987

By E. Uslu

The kinetics of the reduction of chromite from the LG-6 layer of the Bushveld Complex in Fe-Cr-C alloys were studied in the temperature range 15OO°C to 1680°C under an inert argon atmosphere. The rotating cylinder technique was used, and the rotational speed of the chromite cylinder ranged from 0 to 1000 r/min. The melt consisted of 30 to 80 per cent chromium and 2 to 8 per cent carbon. The initial chromium-te-iron ratios of the melts varied between 0,42 and 4,95. The reduction of chromite spinel was analysed in terms of the decarburization of the metal. It was found that decarburization increased with an increase in the temperature, the carbon content of the bath, and the rotational speed of the cylinder up to 400 r/min, after which it remained almost constant. Decarburization also increased with an increase in the chromium content up to about 50 per cent chromium but, at higher chromium contents, it decreased. In the early stage of the reduction, up to about 30 minutes of reaction time, the liquid-state mass transfer of oxygen was found to be the most likely rate-determining step. The apparent activation energy was calculated to be 84,864 kJ per mole of oxygen. In the later stage, diffusion of iron and/or chromium in the solid state is the most likely rate-determining step. The apparent activation energy for the diffusion was calculated to be 471,18 kJ/mol.

Jan 1, 1991

By J. O. Claassen

A study was initiated and solutions implemented to address the root causes of a 30%?40% lower than predicted product yield achieved at a Mpumalanga coal mine. A holistic MRTM approach, which focused on improving exploration, geological sampling and analysis, geological modelling, planning, mining, and beneficiation practices, was used. The study indicated that deviations in the planned versus actual yields at the DMS plant were caused mainly by incorrect geological yield predictions, high and variable levels of dilution, and near-dense material, as well as the textural properties of the ore. Keywords MRTM, mining value chain improvement, Witbank coalfields, complex geology.

Oct 1, 2013

By Lene Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pin point the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable emperature readings and gas analyses could have verified satisfactory activity, hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: Good record keeping is a necessity for collection of representative catalyst samples, reliable operating data is an inevitable starting point for all analysis and trending of operating data is a must for plant optimisation and troubleshooting. In addition these catalyst management tools will give a continuous updated knowledge of the catalyst status in each bed providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking of operating data, temperature optimisation and good record keeping.

Jan 1, 2009

By M. Gholinejad

Applying non-explosive expansion material (NEEM) is one of the safest methods for rock fracturing, especially in a hard rock quarry. An experimental study was conducted to determine the pressure exerted by NEEM in a hole, which is necessary for analysing rock fracturing, particularly in a numerical modelling. Stress distribution was developed in a thick-wall cylinder in order to measure the tangential strain on the external boundary. In the experiments, nine pipes of different materials and varying diameters were selected and then loaded internally with a general type of NEEM. Through electrical strain gauges, the tangential strains were recorded on the external boundary of the pipes. The results obtained from these tests and existing data from previous researchers were utilized for the statistical analysis. A new experimentally-derived formula is proposed for determining the pressure exerted by NEEM by multiple parameter regression with a high correlation coefficient. The proposed model has a nonlinear form with three independent parameters i.e. the hole diameter, the time, and the modulus of elasticity of the material.

Jan 1, 2012

The relationship between the aspect ratio and physical fields in aluminium reduction cells wase studied numerically. The aspect ratio was firstly defined and 7 kinds of 320 kA cells with different aspect ratios were put forward. By using numerical simulation, the relationship between the aspect ratio and the electric-magnetic flow fields, magnetohydrodynamic stabilities, and thermal stability was discussed. It is concluded that the electric-magnetic flow field distributions are greatly affected by the aspect ratio. From the perspective of magnetohydrodynamics stability, the larger the aspect ratio is, the more stable the cell will be. A larger aspect ratio is more beneficial for the thermal stability under the same current density.

Jan 1, 2011

While some of the practical details of ilmenite smelting are not well documented, there is a substantial body of literature on the principles of ilmenite smelting, and the behaviour of solidified titania slag. This information is summarized, focusing on the basic reactions, departure from equilibrium, the behaviour of impurities, and reactions of solidified slag. The emphasis is on the South African operations.

Jan 1, 2007

Iron ore pellets with or without additives are commonly used as alternate charge material in both conventional and newer ironmaking processes. The performance characteristics of these pellets are normally assessed on the basis of their reducibility values, reduction strength and resistance to clustering. These properties depend mainly on the type and amount of additives and on the sintering phenomena of the pellets during firing. In the case of composite pellets (ore-coal pellets), reduction and sintering of the iron ore fines occur simultaneously. The thermodynamic and reaction mechanisms of the processes involved in the reduction of iron ore pellets with and without reductants, additives, etc., may not necessarily be identical. The reduction and sintering characteristics of pellets greatly influence the reaction mechanism and the surface morphology of the reduced pellets. The approaches in the literature to the analysis of these reduction and sintering phenomena are broadly categorized as follows: (i) empirical models, (ii) models based on kinetics, and (ill) models based on morphological changes. The relative merits and de-merits of these models are illustrated by their application to the reduction of fluxed ore-coal composite pellets. A critical analysis of the investigations that have been conducted on the reduction and sintering behaviour of such pellets is given. It is shown that, although elegant empirical models and kinetic equations have theoretical significance and can be usefully employed in elucidating the reaction mechanisms of iron ore lumps, they are sometimes not directly applicable to fluxed ore-coal composite pellets. In studies of the latter, the approach should be to correlate the morphological changes with the reduction mechanism. The paper also gives a brief account of an investigation on the reduction and sintering aspects of fluxed composite reduced iron pellets.

Jan 1, 1996

By F. G. Hill

The paper reviews the restrictions imposed by the Department of Mines (now the Department of Mineral and Energy Affairs) on the surface use of ground that has been undermined at shallow depths (down to a depth of244m). The reasons for the restrictions are discussed, with special reference to the early records kept by the Department of Mines on subsidence and fracture of the surface. A discussion of the nature of the strata overlying the ore-body, and the effect of undermining, is followed by a detailed account of investigational work, particularly since 1970, on the stability of shallowly undermined ground. The significance of the data collected during the investigations is considered next, with special reference to the social and economic implications. These are so farreaching, that it is proposed that the already flexible approach of the Department of Mineral and Energy Affairs in considering what structures may be built on undermined ground should become even more flexible. To this end, the appointment of a Commission is proposed to collect as much information as possible on the stability of ground undermined at shallow depth, and to revise the current overrestrictive conditions or guide lines that are in use.

Jan 1, 1981