Search Documents

By R. W. O. Kersten

"The aim was to investigate stable pillar design procedures currently in use on chrome and platinum mines, subject them to a critical appraisal, and review some of the alternatives proposed in the literature. It is concluded that these pillar design methodologies suffer from drawbacks that can be detrimental to the mining industry and that an improvement is essential.It was decided that the increased availability of analytical models and failure criteria could be exploited to update the empirical to an analytical/empirical method. The proposed methodology adopted FLAC2D simulations using the Hoek-Brown failure criterion to calculate full stress-deformation curves for typical pillars. The mine stiffness concept was introduced to determine the pillar load, integrating the influence of the pillar and strata stiffness and mining geometry.The proposed methodology was calibrated by comparing experimental and predicted deformations and failure depth of pillars in one hard-rock mine. The conclusion was that the methodology is an improvement over the one currently in use. An improved factor of safety is given by the intersection point of curves for the stiffness of the system and the pillar strength. IntroductionThe paper describes part of the findings of a PhD thesis (Kersten, 2016) on an alternative stable pillar design methodology. This publication contains sufficient information to implement the method for further interpretation and testing. A detailed comparison of measured and predicted data is dealt with in the thesis, and the results show that there is promise in the methodology.The design of stable pillars in mining is of fundamental importance, not only in the Bushveld Complex mines but throughout the mining industry. Wherever mining occurs, pillars are formed at some stage and it is essential to predict their behaviour, i.e. whether they will burst, yield, or remain stable. Although of crucial importance, pillar design still suffers from major shortcomings and weaknesses."

May 1, 2019

By M. Stachowiak, M. Nowicki, K. Walas, A. Skoczylas, P. Stefaniak

In this paper the authors present a walking robot dedicated to the inspection of a belt conveyor’s transportation system in an underground mine. The developed robot can independently diagnose all of the key rotating elements of the belt conveyor (pulleys, bearings, drums, gears, engines) based on vibration and acoustic signals as well as typical RGB (red, green, blue) and thermal images. The article presents key diagnostic procedures applied to real industrial data obtained during robot testing.The work was developed as part of the ‘THING–subTerranean Haptic INvestiGator’ project. The authors presented the main assumptions of the research methodology developed for the needs of technical diagnostics of conveyor elements typical of inspection work performed by mining staff. Based on industrial data, the use of algorithms for elements such as rollers, drive stations, and the conveyor belt were shown. The main assumption of the research is to develop a robot adapted to the conditions of a deep mine, capable of carrying out an autonomous inspection of mining infrastructure. The conducted tests and the developed fault detection algorithms were aimed at preparing the robot for underground tests in the operating conditions of the mine.

Sep 1, 2021

By A. Buncombe

In March 1984, two years' work by senior metallurgical personnel from the six major mining groups culminated in the formation of the Mine Metallurgical Managers' Association of South Africa. This Association has joined a group of specialist Associations operating within the South African mining industry whose aims are to uphold the standards and promote the interests of their various professions.

Jan 1, 1987

By NIM REPORTS

Notices CONFRRENCE ON COMPUTRRS IN ENGINEERING The above Conference, which is being organized by the Electrical and Electronics Board of the Institution of Engineer!!, Australia, ill to be held in Sydney on 16th and 17th May, 1974. It is being planned in conjunction with the Sixth Australian Computer Conference and will be held during the week immediately preceding the latter. NIM REPORTS Report No. 1495 A method for the determination of ekmental sulphur on the surface of sulphide minerals. Report No. 1500 The chromatographic separation and determination of nobk metals in matte-leach residues. Report No. 1505 The production of the refractory aluminium saicates, with special refererence to South Africa. Report No. 1517 Computer-controlled flotation plants in Canada and Finland. Report No. 1526 Heat of solution as a control of aqueous-ammonia concentration. Report No. 1529 South African costs of equipment for the metallurgical industry (197).

Jan 9, 1973

By M. A. El-Sayed

"Double oxide films (bifilms) are significant defects in light alloy castings that occur when, during melt handling, the oxidized surface of the melt is folded over onto itself and then entrained into the liquid metal, encapsulating a portion of the local atmosphere. These defects create crevices in the final castings and have been shown to decrease tensile and fatigue properties, and also to increase their scatter, making casting properties unreproducible and unreliable. This paper reports on two different experiments performed to study the behaviour of such defects in Al alloys. In the first experiment and as a proxy for a bifilm, air bubbles were held in an Al-5Mg alloy melt for varying periods of time before the melt was allowed to solidify. The composition of the gas content of the bubbles was subsequently analysed using mass spectrometry to ascertain how it changed with time. In the other experiment the influence of the age of bifilms on the mechanical properties of Al-5Mg castings was assessed by holding castings in the liquid state for different times before solidification, followed by mechanical property testing and SEM and EDX studies of the fracture surfaces of tensile test bars. This research could provide a better understanding of the behaviour of double oxide film defects, and may lead to the development of new techniques by which these defects could be eliminated, or at least deactivated, in light alloy castings. Introduction One of the major structural defects affecting the reproducibility of mechanical properties of aluminium castings is the double oxide film defect (El-Sayed and Essa, 2017; El-Sayed and Ghazy, 2017). This type of defect is usually created as a result of poor filling system design. Owing to the very high reactivity of liquid Al-Mg alloy with oxygen in the air, the surface of the liquid metal can be considered to be permanently coated with an oxide film (Weigel and Fromm, 1990). As a consequence of surface turbulence, the oxidized metal surface can become folded over onto itself, but not fused, and then submerged into the bulk liquid, with a portion of the mould atmosphere being entrapped within it (Campbell, 2003; Al- Sayed, 2016; El-Sayed, Hassanin, and Essa, 2016)."

Nov 1, 2018

By C. J. Lenz

The results of prospecting operations involving geological data and a large number of geochemical determinations of the metal content of soil samples are plotted and evaluated by computer. Anomalous areas are identified in each type of environment by selecting probability or population boundary values from frequency distributions. The anomalies are plotted to permit correlation with geographical or geological features. Ranking of prospecting targets is made using geographic pattern, geology, absolute value and metal ratios. Three short case histories are presented.

Jan 1, 2014

By A. W. S. Schumann

A. W. S. Schumann The first reason for todays success lies in the very high standard which was set by our speakers today and I think that we owe a very special vote of thanks to Messrs P. M. C. Wilson, A. A. Oakes, M. J. Deats, A. C. Coetzee, R. E. Burnton and J. G. Ferguson. This, however, cannot account for the fact that there was a tremendous response even before anyone knew who was going to speak or what they were going to speak about. I suggest that the response was enthusiastic because people expected a more informal gathering with a greater opportunity for feedback, for an exchange of views and for questions and answers. The very popularity of the idea has defeated its own ends to some extent. This gathering is too big and many people must have been left with questions unanswered. Possibly one should arrange for a number of meeting places-there are many in the Chamber and the surrounding mining houses-and then have separate meetings in the morning with joint reporting session in the afternoon. Alternatively, we could have a symposium after the colloquium, using Webster's definition of a symposium as as 'a drinking party of merry fellows'. We all know that it is easy to discuss mining into the small hours. Obviously one cannot summarise todays papers and discussions, but I would like to make a few comments on technical matters and after that I would like to speak for a moment about what I see as major trends or tendencies which arise from discussions of this nature. Regarding the question of placing a village on a mine or away from a mine, I would mention that there is quite a body of literature on the adverse sociological effects on the development of children in any community in which the great majority of parents share the same occupation. It is something to be avoided if possible. We discussed the concept of the moving stockpile. If this is proved to be successful, it could save a considerable amount of money for Escom who could then avoid the construction of very large and costly staithes which are now regarded as parts of power stations. One does not see why both a moving stockpile and a staith should be necessary. By the way, speaking of Escom, I see that Mr Bob Scott is here; he has stopped pulling my leg by saying that we sell stone to Escom; perhaps someone has told him that if this is true, it must be the cheapest stone you can buy in this country. My next point relates to the use of epidiascope. It struck me again that this instrument which provides a visual image to accompany your message, can be very effective if it is properly used. These papers speak of a great deal of hard work which went into their preparation, and one really feels that the authors should have taken a few minutes more to prepare their drawings specifically for the epidiascope. There should be nothing on the drawing which is not necessary to illustrate a particular point and there should be nothing on the drawing which is not visible from the back of the hall. In particular, if one cannot read the figures along the sides, then one

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

By J. E. Gebhardt, B. Temel Mckenna, W. Lee, C. S. Macomber

X-ray diffraction (XRD) data was extracted from various sources to develop qualitative ternary and tetrahedral plots differentiating mineralogy, bond work index (BWi) and hardness of ore bodies at different mine sites. A large number of historic reports and compiled characterization laboratory data were used to create a searchable "data lake." The data lake provides a means to locate, consolidate, and visually represent XRD from disparate sources. Visualizations with large amounts of mineral ore XRD characterization data provide a qualitative assessment of ore properties, including comminution qualities such as material hardness. The visual map can be employed to quickly estimate expected ore character and behavior, given XRD analysis of samples from newly characterized and unfamiliar ore. Keywords: Mineralogy, Characterization, Comminution, Database, Ternary, Tetrahedral

Jan 1, 2020

By H. Laitala, M. Lampi

Metso Outotec has developed a wide range of solvent-extraction technologies over decades and has introduced Metso Outotec VSF®X solvent-extraction plant. Standardized and modularized, Metso Outotec VSFX Plant provides a novel way to design, manufacture, transport, install, operate, and maintain solvent-extraction plants far better than in the past with highly sustainable and safe methods. For the customer, this means fast-track projects with savings in means of time, costs, quality, and operation. Sicomines and Metso Outotec have together implemented and commissioned a modern and efficient copper solvent-extraction plant. Plant commissioning and ramp up of the plant were fast and the plant is now operating efficiently. This paper presents Sicomines’ VSFX copper solvent-extraction project and gives a sight into operating figures for the plant.

Jan 1, 2023

By J. P. Garnier, T. Bhambhani, J. A. Garcia, N. Renaud

Most flotation plants use a static reagent scheme, i.e., a set combination of collectors, frothers, and modifiers. This scheme is usually developed and refined over time to deliver optimal (not necessarily the highest) performance when the major ore types are fed to the plant. However, when ore types or mineralogy coming to the plant change substantially (and this often happens as different areas of the pit(s) are mined and crushed at the same time), there are upsets in the process, typically leading to lower recoveries. Adapting to this variability is usually done only when performance drastically suffers, and the changes made may be too late and bring additional variability in performance. The premise for SmartFloat™ is that the reagent suite needs to be dynamic, adapting continuously to changes in the ore and operating conditions. Solvay has combined advanced analytics and data science techniques with its expertise in flotation reagent chemistry to systematically and automatically achieve the above, and in real time. Thus, SmartFloat™ is optimizing the reagent suite continuously, removing the additional variability created by belated human interactions resulting in a better and more stable process. In addition, this advanced approach allows for continuous improvement by identifying poor performing ore domains and improving the reagent suite using Solvay’s FM-100 approach to design appropriate solutions.

Jan 1, 2023

By N. Snyders, I. Mwandawande, S. M. Bradshaw, M. Karimi

"Flotation columns are normally operated at optimal superficial gas velocities to maintain bubbly flow conditions. However, with increasing superficial gas velocity, loss of bubbly flow may occur with adverse effects on column performance. It is therefore important to identify the maximum superficial gas velocity above which loss of bubbly flow occurs. The maximum superficial gas velocity is usually obtained from a gas holdup versus superficial gas velocity plot in which the linear portion of the graph represents bubbly flow while deviation from the linear relationship indicates a change from the bubbly flow to the churn-turbulent regime. However, this method is difficult to use when the transition from bubbly flow to churn-turbulent flow is gradual, as happens in the presence of frothers. We present two alternative methods in which the flow regime in the column is distinguished by means of radial gas holdup profiles and gas holdup versus time graphs obtained from CFD simulations. Bubbly flow was characterized by saddle-shaped profiles with three distinct peaks, or saddle-shaped profiles with two near-wall peaks and a central minimum, or flat profiles with intermediate features between saddle and parabolic gas holdup profiles. The transition regime was gradual and characterized by flat to parabolic gas holdup profiles that become steeper with increasing superficial gas velocity. The churn-turbulent flow was distinguished by steep parabolic radial gas holdup profiles. Gas holdup versus time graphs were also used to define flow regimes with a constant gas holdup indicating bubbly flow, while wide gas holdup variations indicate churn-turbulent flow. IntroductionTwo types of flow can be distinguished in gasliquid flows in bubble columns: bubbly flow and churn-turbulent flow. The bubbly flow regime is characterized by uniform flow of bubbles of uniform size. Churn-turbulent flow, on the other hand, is characterized by a wide variation in bubble sizes with large bubbles rising rapidly and causing liquid circulation.Flotation columns are normally operated in the bubbly flow regime, which is the optimal condition for column flotation (Finch and Dobby, 1990; Yianatos and Finch, 1990; Ityokumbul, 1992). However, it has been generally observed that flotation column performance deteriorates when the superficial gas velocity is increased beyond a certain limit where the flow regime changes from bubbly flow to churn-turbulent flow (Xu, Finch, and Uribe-Salas, 1991). The identification of this critical or maximum superficial gas velocity is therefore important for optimal operation of flotation columns."

Feb 1, 2019

By A. Mainza, I. Govender, Elbasher M. E. Ahmed

A mechanistic description of axial segregation in rotating drum flows remains an open question. Consequently, optimal mixing of grinding balls and rocks for efficient breakage, maximum production of fines, and slurry transport is seldom achieved. Experimental and numerical studies of granular mixtures in rotating drums identify alternating axial bands that eventually coarsen in the long-term limit. Most models of axial segregation are limited to binary mixtures and cannot always predict the logarithmic coarsening effects observed experimentally. A key missing factor is a robust description of the axial free surface profile that is valid across a wide range of flow regimes. We present a practical model of the axial free surface profile by linking it to readily-derived geometric features of the cross-sectional S-shaped free surface profile. A parametric study shows good agreement with experimental measurements reported in the literature and heuristically valid trends.

May 1, 2021

By A. Brodt, I. Mezhibovsky

The traditional vertical transportation systems deliver both gangue and useful mineral. The extraction of the desired minerals requires the construction of mineral processing and waste management plants, driving production costs, and often creating a negative environmental impact. The proposed technology is an integration of mineral processing within the transportation system. The mined rock is crushed and then loaded into a vertical lifting system filled with heavy media, with an intermediate density between the mineral and the waste rock. Driven by gravity separation, the desired mineral floats to the earth's surface, while the waste sinks. Delivered minerals and sunk waste is extracted from the heavy media and is then regenerated to a dry state. The useful mineral should be suitable for further use, and the waste used for backfilling. Remained residues of the heavy media may be recycled and reused in the vertical transportation system. Trials of the proposed process in a pilot format have confirmed economic and environmental advantages over traditional methods of transportation and mineral processing technologies. Keywords: Gravitational processes of mineral processing, separation in heavy media, vertical transportation to earth's surface by floating up

Jan 1, 2020

By R. o. Cretier, L. A. Cisternas, A. López-Valdivieso, F. Valdes, E. Gálvez, G. Gahona

The size of the particle plays an important role in the flotation of minerals. Comminution allows the release of valuable species and their subsequent recovery. Then, the degree of concentration and recovery will depend on the size of the particle. In this work, we investigated the flotation of coarse particles (-850 +150 μm) of copper ores when using the fluidized-bed separator (HydroFloat® cell) and compared it with the process of conventional flotation with medium size particle (-150 μm) (Metso cell) using seawater. The collector concentration was the main variable studied in terms of copper recovery. The results show that the flotation of coarse particles is feasible using seawater without frother

Jan 1, 2020

By J. Bullón, A. Pérez

Some years ago, Ferroatlantica developed a new type of electrode known as the ELSA electrode. In this electrode there is a central graphite core that provides support, surrounded by an annulus of Søderberg paste that gets baked during operation. This technology has been implemented on several silicon furnaces around the world, and was reported on during the previous Infacon conference. In all electrodes, but particularly in the ELSA electrode, the quality and consistency of the paste are important for correct operation. As the type of paste varies between customers and between countries, Ferroatlantica has developed a quality control procedure for their customers of this technology. This procedure is geared to the point of view of the customer rather than the paste producer. The analysis is based on the desired flow pattern of the raw paste and on the desired mechanical and electrical properties of the baked paste, as experience has shown that these are the most important parameters to monitor in order to avoid having problems with the resulting electrodes. This paper discusses these methods of paste analysis in the light of complementary studies that have been done when there has been an electrode breakage in the different plants.

Jan 1, 2007

By G. R. Lane

My opportunity to serve as President of the prestigious Southern African Institute of Mining and Metallurgy (SAIMM) was made possible by an Anglo American scholarship 39 years ago—a pivotal moment that set me on a career path spanning various roles and start-up ventures in the mining industry. Over the past decade, I have been privileged to broaden my experience by consulting across diverse industries globally. This exposure revealed something profound: what I had previously considered mining-specific challenges are, in fact, universal across many sectors. At its core, a mining operation is a complex system of interconnected activities—from exploration through mining operations like drill and blast, load and haul, to beneficiation, and outbound logistics. My cross-industry work has clearly shown that diverse sectors, such as chocolate manufacturing, tissue paper production, toilet paper converting facilities, labgrown diamonds, or high-tech equipment lifecycle management, all rely on value streams of interconnected activities to transform products. The objective is to maximise throughput while effectively managing performance variability. The primary difference lies solely in the specific technical expertise required for each industry, such as chemical, mining, processing, or metallurgical engineering. Across all these industries, I have observed a consistent pattern, that is, performance is primarily driven by individual efforts, where people react and work diligently as situations unfold in real-time. General managers and their teams often operate tactically, focusing on explaining yesterday’s poor performance rather than proactively setting up operations for success. This often resembles an ‘‘under-7s soccer match’’, with everyone chasing the ball. The common response to issues is to add more ad hoc meetings. This effort-driven organisational behaviour persists regardless of whether operations are greenfield digital manufacturing facilities, advanced digital mines with advanced process control, or operations run on paper and Excel spreadsheets for data acquisition. Paradoxically, more real-time data can lead to increased data noise, greater indecision, and sometimes, lower performance. Despite value streams often operating significantly below capacity, organisations continue to invest heavily in additional equipment or in ‘‘glossy brochure promises’’ of Industry 4.0 digital technology and real-time data solutions, which frequently fail to deliver value. This leads to a critical question: Have we underinvested in our most valuable resource— people? Even Tesla faced this challenge with their underperforming fully automated Model X facility. We must shift our focus to designing the ecosystem, or operating model, of our organisations. This extends beyond the traditional triad of people, process, and technology, and moves beyond simplistic views of change management. Artificial Intelligence (AI) has the potential to add significant value, but it also introduces another layer of complexity into designing the organisation of the future. My full presidential address below at the SAIMM AGM discussed the symptoms of an effort-driven organisation and covered the fundamental building blocks and requirements of an operating model, including recommendations on implementing a people-centric approach.

Oct 2, 2025

By K. C. Naidoo

There are two main types of densifying cyclones currently available in the market, namely polyeurethane (PU) and ceramic. The PU densifying cyclones are currently used throughout the Grootegeluk complex and coal beneficiation in general. It has been identified that PU densifiers wear relatively fast depending on the operating pressure and need to be replaced frequently as a result. The motivation for this paper is to achieve an increase in the densifying cyclone lifetime through less wear and an increase in efficiency resulting in the ability to build higher relative densities (RD) more quickly. This will allow for a reduction in downtimes due to replacing densifying cyclones as well as building RD and a reduction in the operating costs associated with replacing worn densifying cyclones. Some of the major findings of the study indicated that the ceramic cyclone theoretically undergoes less wear than the PU cyclone, but since wear is application-specific and was evaluated, the wear on the polyurethane cyclone was found to be minimal. The RD differential is higher on the PU cyclones than the ceramic cyclones, showing that the PU cyclones perform better in a densifying application. This is the first test conducted on this application and type of cyclones. It should therefore be noted that having the PU cyclone significantly outperform the ceramic cyclone was not expected, due to the only change being the material of construction. This is an indication to take the material of construction into account when selecting cyclones as it can have a significant impact on the cyclone performance in specific applications. Keywords: Ceramic, cyclone, densifying, density, dense medium, polyurethane, wear

Jan 1, 2020

By H. S. Baloyi, J. J. Rust

Spiral concentrators are widely applied to beneficiate commodities such as Cr2O3, mineral sands, and ferrochrome. The application of spirals for heavy minerals has been limited to a feed top size of 1 mm. At particle sizes larger than this, friction retards heavy particles and the particles' primary velocity approaches zero, resulting in a solids build-up, therefore inhibiting further separation. Recently, a new Multotec SC25 spiral model was introduced to the industry, which aids in beneficiating particles of up to 3 mm, with successes having been demonstrated in ferrochrome slag and titanium-bearing minerals. This spiral also has potential in electronic waste applications. This paper examines the applicability of the SC25 spiral in coarse Cr2O3 recovery. This stems from the fact that junior chrome miners tend to discard particles larger than 1 mm as they neither have milling nor dense media circuits. Also, alluvial chrome miners discard +1 mm even though this size fraction contains recoverable and liberated Cr2O3. The SC25 spiral has shown better Cr2O3 separation efficiencies than the SC21 model and with higher SiO2 rejection at saleable grades, thus providing an additional revenue stream specifically for the coarser (+820 μm) size fractions. Keywords: Spiral concentrators, chromite recovery, specific gravity, SC25 spiral, coarse spiral

Jan 1, 2020

By M. Hao, S. Hu, X. Lyu, M. Lian, C. Anning, G. Yao, Z. Wang

The results revealed that the pozzolanic activity of the gold mine tailings and their main mineral phases improved by mechanical activation. Under the same activation conditions, the activated mica powders possessed the highest pozzolanic activity index, followed by the activated feldspar, and the activated quartz exhibited the lowest pozzolanic activity index. The addition of calcium oxide promoted the formation of amorphous C–(A)–S–H gel for all paste samples, and stratlingite and hydrotalcite were observed in calcium oxide activated mica paste. The addition of natural anhydrite promoted the formation of ettringite for the pastes of calcium oxide activated aluminosilicates materials (gold mine tailings, mica, and feldspar). Furthermore, the pozzolanic activity indexes of the mechanically activated gold mine tailings and their main mineral phases were tested to be qualified for use as supplementary cementitious material in cement. This paper provided an innovative approach for recycling gold mine tailings as supplementary cementitious materials in cement, which would be environmentally friendly and cost-effective. Keywords: Mechanical activation, gold mine tailings, supplementary cementitious material, hydration properties, pozzolanic activity

Jan 1, 2020