Search Documents

By L. J. Su, J. Y. Zhang, P. W. Gu, J. F. Xu

Surface tension of mold flux is a key factor affecting optimum casting conditions. A thermodynamic model was developed to determine the surface tension of mold flux containing fluoride based on the ion and molecule coexistence theory of slag structure and Butler’s equation. The relationship between composition and surface tension was investigated by this model. Results indicated that the calculated values showed good agreement with literature data, and the average error was 8.19%. The surface tension value of the CaO–Al2O3-based mold flux was larger than that of the CaO– SiO2-based mold flux. The surface tension in a multi-component system decreased with increasing contents of SiO2, CaF2, and Na2O, which are considered surface-active components. This trend was more significant in the CaO–Al2O3-based mold flux.

Dec 11, 2024

By El-Sayed M. Sherif, J. D. Comins, Erasmus R. M.

Corrosion of copper in aerated acidic chloride pickling (0.5 M HCl) solutions and its inhibition by 3-amino-1,2,4-triazole-5-thiol (ATT) have been investigated using electrochemical techniques and weight-loss measurements, along with Raman spectroscopy. Electrochemical measurements for copper after varied immersion periods of 0, 24 and 48h showed that the presence of ATT and the increase of its concentration significantly decrease cathodic, anodic, corrosion (jCorr) currents and corrosion rates (KCorr), as well as the dissolution currents at 300 mV vs. Ag/AgCl, while increase polarization resistance (Rp), degree of surface coverage (?) and inhibition efficiency (IE%) to a great extent. Weight-loss measurements after different immersion periods of 6 ~ 48h revealed that the dissolution of copper decreased to a minimum and the corresponding IE% increased with ATT concentration increases. The detection of ATT molecules on the copper surface by Raman spectroscopy indicated that inhibition of copper corrosion is achieved by strong adsorption of ATT molecules onto the copper surface. Aerated acidic pickling solutions; 3-Amino-1,2,4-triazole-5-thiol; Copper corrosion; Corrosion inhibition; Raman spectroscopy

Jan 1, 2006

By V. A. Leão, V. S. Coimbra, V. A. A. Oliveira, R. F. M. de Souza, G. M. de Lima

A willemite concentrate consisting mainly of willemite (55.3%) and dolomite (15.6%) was reduced in a tube furnace with charcoal as reductant. The effects of temperature and varying reductant additions on zinc extraction were studied. A zinc recovery of 86% was achieved with 20% reductant in the charge at 1100°C. During reduction, the calcium oxide generated through calcination of the dolomite promoted decomposition of the willemite, thus lowering the temperature at which reduction took place. The presence of CaO improved the zinc recovery at all temperatures studied. The best zinc recovery (93%) was obtained in the presence of 5% CaO, 20% charcoal reductant, and at a temperature of 1100°C. The results show that the willemite concentrate studied has great potential to be used as a raw material for the Waelz process.

Nov 6, 2023

By X. Xiang, W. Xia, J. Yin

"TiCl4 slurry containing valuable metals is an unavoidable by-product of the titanium ore chlorination process. The recovery of these valuable metals, which include titanium, niobium, tantalum, and aluminum, is an urgent issue to tackle in the titanium industry. The results of this investigation show that the valuable metallic elements can be recovered from the slurry by evaporation in a sealed container and leaching with dilute hydrochloric acid. After evaporation at 200°C for 60 minutes, nearly 99% of the titanium was recovered in the form of TiCl4, which was formed by the reaction of the TiO2 in the slurry with AlCl3. After evaporation, metals like niobium, aluminum, and tantalum remained in the residue. By leaching with 2.1 mol/L HCl at a L/S ratio of 6:1 mL/g at 80°C for 60 minutes, the soluble metals, such as aluminum, iron, and copper were all removed from the residue, and the niobium and tantalum were further enriched in the leach residue. A concentrate containing 53.40 wt% Nb and 5.57 wt% Ta was obtained by washing the leach residue with dilute aqueous ammonia under stirring. A potential waste water purifying agent containing 263.75 g/L AlCl3 was produced by purifying the leaching solution with Al(OH)3 and modified polyacrylamide. IntrodutionTitanium tetrachloride (TiCl4) is an important intermediate in titanium metallurgy that is widely used in the production of titania and titanium sponge (Akhtar, Xiong, and Pratsinis, 1991). In conventional titanium metallurgical processes, high-titanium materials such as synthetic rutile and high-titanium slag are reacted with chlorine to produce TiCl4 in a fluidized-bed furnace. Accompanying elements, such as Al, Nb, and Fe also react with chlorine to form chlorides, which are mixed with gaseous TiCl4 (Anderson, 1917). In the condensation process, gaseous TiCl4 is refrigerated and high-boiling-point chlorides are precipitated in the liquid TiCl4 to form a slurry containing 50~60 wt% TiCl4 (Wang, Xiang, and Wang, 2012).Various methods have been proposed to recover TiCl4 from the slurry, including microwave heating and spray drying (Wang, Xiang, and Wang, 2012, Wang et al., 2010a). To date, the only way to recover the TiCl4 is to return the slurry to the fluidized-bed furnace. However, this causes fluctuations in the temperature in the furnace, resulting in incomplete reaction between titanium-rich materials and chlorine. Therefore, the slurry is often rinsed with water and neutralized by adding lime, which caused serious environmental pollution and wastes a valuable resource (Roy, Bhatt, and Rajagopal, 2003)."

May 1, 2019

By M. Wrobel, J. Hammerschmidt, M. Runkel

Fluid-bed technology is a key pyrometallurgical step for processing a vast number of ores and concentrates. Over the past 50 years, considerable research and development efforts have been made by Metso Outotec to expand the application window of this technology. This paper illustrates different processing routes where fluid-bed technology plays an important role in the production of the copper. The fluid-bed processes utilized are partial, sulfate-producing, and dead roasting. The focus of this paper considers the advantages of the dead-roasting process. This “zero waste” process can provide copper oxides, steam, electrical power, and sulfuric acid for new and existing solvent extraction–electrowinning plants. In a case where an operation is running out of oxidic ores and concentrates, fluid-bed roasting can be applied to close this gap and provide the required copper oxides in a sustainable way.

Jan 1, 2023

By P. Ramphisa

In South Africa reprocessing used oil into industrial fuel is commercially attractive. The reprocessed product is sold as a substitute for heavy fuel oil that is derived from crude oil (Rose Foundation, 2008). The objective of this investigation is to evaluate the use of petroleum products such as oil, petrol and diesel in Driefontein Gold Mine. The recovery of oil through recycling has costs implications to the mine while the release of petroleum hydrocarbons due to the poor management of the use of petroleum products has potential to cause pollution and negatively affect soil and water. Environmental legislation such as the Minerals and Petroleum Resources Development Act (Act 28, 2002) requires that such negative impacts to the environment be rehabilitated. The rehabilitation cost of pollution caused by petroleum products to the environment increases operational costs in business. Field assessment is conducted to identify the main sources of petroleum product contamination such as leaks in piping, overfills and petroleum spills. The areas that require mitigation would be mapped in the study. Recommendations for mitigation measures will focus on using the best practicable environmental option (BPEO) as well as the best available technology not exceeding excessive cost (BATNEEC). The recovery of oil from the mining industry is generally low and very poor. In this study, the effect of proper management of petroleum products to the mine?s operational costs is investigated and compared to there mediation costs of the impacts caused due to poor management of these products. The study investigates the financial benefit that could be obtained from proper environmental practices and efficient usage of petroleum products in the mining.

Jan 1, 2009

By W van Drunick, S Naik

To date, Anglo Research has carried out several projects, based on the techniques developed in the AMIRA P9 (AMIRA International Limited), to develop comminution and flotation models for several Anglo Base Metals and, to a lesser degree, Anglo Platinum flotation plants. Plant optimization is thus achieved through steady-state sampling, model-fitting and simulation using the JK SimMet and JK SimFloat software packages. The surveys can vary depending on the needs of the plant/client. The survey can therefore include as little as a single piece of equipment, an entire milling/flotation circuit, or a complete circuit from primary comminution to final flotation concentrate (i.e. the ?integrated survey?). The presence of the AR team on-site usually precipitates in face-value observations that can lead to initial improvements. This stems from the knowledge-sharing on best practice that exists in parallel with the surveys. Numerous (reasonable) changes can then be simulated, thus indicating the optimization step most likely to result in the best efficiency improvements. The simulations can include changes in the flowsheet, ore characteristics, mill loads, grinding media size, change in grind, flotation residence time, air hold-up and several more. Plant surveys can result in process changes that provide the plant with either: higher plant tonnage, improved plant grind, additional flotation recovery and/or improved product grade. The additional benefit of performing an integrated plant survey is that the effects of an optimization change in the comminution circuit can be simulated using the flotation model. This paper describes a number of case studies where individual and integrated plant surveys were conducted by AR for Anglo Base Metals.

Jan 1, 2007

By R. J. Durrheim, Y. Yabe, M. S. D. Manzi, DSeis team, N. Z. Nkosi, S. B. Mngadi, Jr. H. Ogasawara

On 5 August 2014, the Orkney M5.5 earthquake, the largest in South African gold mining districts, occurred with an unusual strike-slip mechanism at great depth of 4.78 km below the surface. In a rare case, the ML 5.5 earthquake occurred within the area covered by the legacy 2D and 3D reflection seismic data acquired in the 1990s and 2000s for gold exploration and mine development. In addition, the earthquake ML 5.5 rupture plane was recorded and accurately delineated by the underground in-mine seismic network near the source region. The integration of the legacy 2D reflection seismic data and mine seismicity data allowed us to identify a near-vertical structure, striking northnorthwest-south southeast (NNW-SSE). The ICDP-DSeis team drilled three holes (Hole A, Hole B, and Hole C), and two holes (Hole B and Hole C), intersected the upper edges of the ML 5.5 rupture. These holes recovered metasediments, metabasalts, intrusive rocks including dolerite sills and lamprophyre dykes adjacent to the fault zone, and the fault gouge. Late Prof. Tullis Onstott and geomicrobiologists installed a packer in Hole A and successfully recovered saline water and detected gas (~10 MPa). Slip weakening and rupture propagation are significantly influenced by the existence of fault gouges and the production of wear material between two sliding rock surfaces. Using the fault gouge material recovered from Hole C, we conducted friction experiments under dry and room temperature conditions at high slip velocity of ~100 mm/s and normal stress of 2 MPa. The resulting steady-state frictional strength was ~0.66 over a slip weakening distance of ~9.1 m. The steady-state frictional strength was high, which may be caused by large gouge thickness, and the rate of wear generation. As a result, it is proposed that the Moab Khotsong ML 5.5 seismogenic zone is complex and could be controlled by three main processes: a) the complex structural architecture of the seismogenic zone (e.g., intersection of fault, lamprophyre dykes, and dolerite sills); b) the mechanical process induced by tectonic and/or mining related stresses; and c) the mechanical and chemical processes caused by the water and rock interaction.

Jan 12, 2025

By A. K. Raji, E. F. Orumwense, M. O. Ojumu

This research paper introduces a novel passive method for ocean mining using an electricpowered robotic subsea dredging crawler designed to operate in various subsea conditions, including unstructured and rough terrain. The electric-powered robotic subsea dredging crawler is equipped with two driving tracks and features a complex assembly of tank tread chain link, tank tread idler wheels, tank tread sprockets, bronze bushings, motor hub, motor mount, and a 12-volt direct current motor. To evaluate the performance of the electric-powered robotic subsea dredging crawler, it was compared with existing ocean hydraulic exploration crawlers, such as MK3 ROST, in terms of drive performance on an inclined ramp with five angles of inclination (0°, 15°, 20°, 25°, 30°). The experiment aimed to determine the maximum velocity, torque, and efficiency of the crawler at different angles of inclination. The collected data were analysed and plotted using Python, and the effect of the electric-powered robotic subsea dredging crawler’s weight on its driving performance was also considered. The results of this study demonstrate a quadratic relationship between driving performance and inclination angle, which can be used to optimise the electric-powered robotic subsea dredging crawler’s performance for future ocean mining robot drive applications.

Oct 2, 2025

By Xiaoxu Sun, Jianchao Yao, Qiheng Zhu, Dubo Wang, Jiancheng He, Shijie Lu

Tower mill is considered to have a better regrinding and fine grinding effect compared with ball mill, and its application is much broader. The spiral agitator of the tower mill is driven by the motor. Media inside the mill is under the combined actions of the spiral mechanism, the cylinder, and media nearby, and these parameters are key factors affecting the grinding effect. However, it is not possible to obtain detailed information of kinematic law of media based only on traditional laboratory experiments, let alone the relationship between parameters of kinematic law of media and grinding effect. Experimentation is the only way to develop industrial equipment. However, this is time-consuming and costly, which hampers the further research of the tower mill’s grinding mechanism. The paper selects two structural parameters (gap between the edge of the spiral agitator and the cylinder wall, ratio between the diameter of cylinder and that of the spiral shaft.) and three operating parameters (diameter of media, filling ratio, the speed at the edge of the spiral agitator) as variables to do an orthogonal designed experiment of five factors, four levels, and thereby obtaining change law of grinding indicators of different parameters. Experimental equipment may be simplified to enable an applicable simulation strategy. Simulation based on a discrete element method is conducted to obtain the change law of the speed of media, collision frequency, normal force, and radial force. The relational curve between parameters of kinematic law of media and energy consumption of grinding is clarified, and key factors affecting grinding efficiency are determined. Those factors will be used for optimising the design and operating process. The research result of this paper obtained from laboratory experiments and computer simulation provides data support and theoretical bases, and has directive meaning and applicable value for tower mill’s optimisation and large-sized design. Keywords: Tower mill, discrete element method, kinematic law of media, energy consumption of grinding

Jan 1, 2020

By E. R. Leeman

INTRODUCTION The first references in the literature to the so-called C.S.I.R. 'doorstopper' strain cell were made in 1964 1,2,3,4. These were the climax of nearly two years of experimental and developmental work with the instruments and the operating techniques involved. Since that time numerous field measurements have been made with 'doorstoppers' and they have been developed to a stage where they are in commercial production and are being supplied to users throughout the world. No detailed description of the latest 'doorstopper' equipment has, however, appeared in print and this paper is written to bring the literature up to date in this respect. The triaxial strain cell was developed three years ago 5, 6, 7 and was first described at the First Congress of the International Society for Rock Mechanics in Lisbon in 1966 8. Since that date laboratory tests and-particularly important-field tests 7' 9 have demonstrated the validity and practicality of the instruments and techniques. These instruments have also been developed to a stage where they have been released for commercial production. In this form they are very different from those described two years ago and a full description of them at this stage seems to be justified. THE INFORMATION SUPPLIED BY 'DOORSTOPPER' AND TRIAXIAL STRAIN CELLS Both the 'doorstopper' and triaxial strain cells were designed specifically to determine the absolute stress in rock using an overcoring stress relieving technique. They were not designed to measure changes in stress. They may, however, be used for the latter purpose provided the glue which is used to stick the strain gauges to the rock is known to possess sufficiently stable strain-time characteristics as not to affect the accuracy of the results during the time the measurements are made. The 'doorstopper' was designed primarily to measure the major principal stress in situations where its direction and those of the two other principal stresses were either known or could be assumed. For example, at great depth in undisturbed virgin ground, it is reasonable to assume that the maximum principal stress is vertical and that the other two lie in a horizontal plane. The borehole in which the 'doorstopper' is installed would thus be drilled in the horizontal plane parallel to one of the minor principal stresses, the direction of which would either have to be assumed or determined as described later. The stresses measured would be the vertical major principal stress and the principal stress acting in a horizontal plane normal to the borehole axis. It is possible, as will be shown later, to obtained the complete state of stress using 'doorstoppers'. In this event, it is necessary to make measurements in three boreholes drilled in any three known directions to each other and relative to a system of three orthogonal axes. The triaxial strain cell was designed to determine the complete state of stress in a single borehole drilled in any direction in any stress field. At first glance it would appear to supersede the 'doorstopper'. This is not necessarily true since there are

Notices TRANSPORTATION AND THE ENVIRO NMENT The 5th Quinquennial Convention of the S.A. Institution of Civil Engineers will take place at the Carlton Centre, Johannesburg, from 20th to 24th August, 1973. ENVIRONMENTAL ENGINEERING A conference on environmental engineering problems in industrialized and developing countries is to be held at the United Engineering Centre, New York, on 19th and 20th September, 1973. RABCEWICZ-COLLOQUY The Austrian Society for Geomechanics is to honour Professor Ladislaus V. Rabcewicz, on the occasion of his 80th birthday, with a meeting in Salzburg Congress Hall on 11th and 12th October, 1973. The themes of the four half-day sessions will be as follows. PYRO MET ALL URG ICAL EVENTS IN 1974 Diisseldorf is to be the venue for the following three events: International Iron and Steel Congress O.F.S. Branch Welkom THE MARCH GENERAL MEETING OF THE BRANCH WAS HELD IN THE ST. HELENA CLUB AT 8.00 P.M. ON TUESDAY, 6TH MARCH, 1973 O.F.S. Branch Welkom MINUTES OF A GENERAL MEETING HELD IN THE ST. HELENA CLUB ON WEDNESDAY, 16TH MAY, 1973, AT 8.00 P.M.

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant oven, it was essential to ascertain coal cake stability during the loading of a 1 m3 (1 m × 1 m × 1 m) coal cake into the cold pilot-plant oven by a pusher mechanism. Previously established laboratory-scale compaction parameters, to obtain coal cakes with sufficient stability, were employed during the loading tests of the coal cakes. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.It was demonstrated that lower applied compaction forces (14%) can be utilized during 1 m3 compaction, in comparison to laboratory-scale tests, to obtain similar wet cake densities, owing to differences in the effect of frictional forces. Wet cake densities for Waterberg sscc improved slightly (3%) to 1.13 t/m3 when utilizing 79 t/m2 applied force for a 1 m3 coal cake, in comparison to laboratory-scale tests. Similar results were obtained for Oaky North hard coking coal, with a 6% density increase to 1.27 t/m3 at a similar applied force. Porosities decreased by 13% and 32% for Waterberg sscc and Oaky North coal, respectively, when 1 m3 compaction was compared to laboratory-scale tests. An opportunity exists to further decrease the porosities of Waterberg sscc during compaction, whereas acceptable compaction parameters were achieved for Oaky North hard coking coal. Most major vertical cracks and the partial collapse of coal cakes were mitigated, and high-stability coal cakes were obtained that could be successfully loaded into the pilot-plant coke oven by a pusher mechanism.Factors contributing to the instability of the coal cake during loading into the oven, such as vertical cracks, are (i) the cubic geometry (1 m3) of the coal cake, (ii) friction exerted by the oven floor, and (iii) mechanical problems, such as a misalignment between the pusher machine feeder plate and the oven floor. IntroductionOperation of the stamp-charging horizontal 1 t electrically heated coke pilot-plant oven at Exxaro Resources requires coal cake stability during the loading of a 1 m3 compacted coal cake into the oven. In this case, a pusher plate is utilized to push the coal cake into the oven over the oven floor. This is in contrast to a ‘spoon’ or bottom plate feeding mechanism as found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability for the 1 t coke oven, various compaction parameters need to be verified and established."

Apr 1, 2019

By C. J. Liebenberg

This paper focuses on the application of ion exchange technology for the recovery of copper from a leach solution originating from a heap bioleach in which base metals are leached from a low-grade ore that bears platinum group metals. Screening tests indicated that Dow XUS43605 has high selectivity for copper over the other metals in the solution, namely nickel, iron, cobalt, zinc, manganese, and aluminium. Batch adsorption kinetic experiments showed that copper adsorption equilibrium is attained at a fast rate. The kinetics of adsorption increased as the temperature was increased from 25°C to 60°C due to the decrease in solution viscosity and the subsequent improved intra-particle mass diffusion. Single-component Langmuir and Freundlich isotherm models were fitted to the batch copper adsorption equilibrium data, and a maximum copper capacity of 26 g/l was observed for Dow XUS43605. The effects of flow rate, temperature, pH, and initial metal concentration on the dynamic recovery of copper were investigated in fixed-bed columns, and it was determined that temperature and flow rate had the most significant impacts on the loading of copper on the resin at copper breakthrough. A 36% increase in copper loading at breakthrough was observed when the temperature was increased from 25°C to 60°C. Finally, it was determined that a split elution is possible by using different concentrations of H2S04 to first elute co-loaded nickel from the resin, followed by the elution of copper.

Jan 1, 2013

By S. Ata, Y. Pan, S. Gautam, G. Bournival

Bubbles play a vital role in flotation, and their properties directly affect the flotation performance. Xanthates are one of the major collectors used in sulphide mineral flotation. It is often believed that their main function is to render the desired mineral surface hydrophobic, which is essential for the mineral particles to attach to air bubbles. This paper takes a systematic approach to assess the influence of potassium amyl xanthate (PAX) at the air–liquid phase and its interaction with the frother in the concentration of range 10–5×104 ppm. Bubble size was measured in a laboratory flotation cell using a photographic technique and the stability of bubbles was quantified in terms of coalescence time -, the time required for a bubble pair produced at adjacent capillaries to merge into a single bubble. Bubble size reduction of up to 26% was observed with increasing PAX concentration in the cell. The bubble coalescence experiments using PAX only showed that the bubbles coalesced quickly at lower concentrations (10–50 ppm), but they stayed extremely stable at higher concentrations (1×102–1×104 ppm). Further experiments were carried out where the concentration of PAX was fixed at 1 ppm and 4- Methyl-2-pentanol (MIBC) concentration was varied. The synergetic action of PAX and MIBC significantly improved the stability of bubbles in the mixed system, and is even compatible with a stronger frother. The results strongly suggest that the role of PAX at the air–liquid phase should be considered in the practice of sulphide flotation. Keywords: Bubble size, bubble coalescence, PAX, bubble stability

Jan 1, 2020

By R. Hutchings

The paper reviews current understanding of the effect of ion implantation on the wear process, and the state-of-the-art of ion implantation as a commercially viable treatment to impart wear resistance. Ion implantation involves the firing of high-energy ions into the surface of a material, which modifies the surface properties and so causes a transition in the dominant wear mode. The process is best suited to specialized engineering applications involving critical dimensional tolerances or surface finishes, but has gained little industrial acceptance because of its poor reproducibility and the lack of a suitable method of inspection.

Jan 1, 1986

By C. R. Speers, M. I. Forsyth

The paper describes how stress analyses were used to show the defect of a tunnel's shape on the overstressing potential of its periphery. The best profile was found to be that of a horizontal ellipse, for which there was little significant scaling, permitting temporary support to be incorporated into a permanent tunnel support system. This investigation was followed by the modeling of several support systems for tunnels with a horizontal-ellipse profile, which showed that such a profile can reduce the installed support required for a tunnel of different cross section by an average of 57 per cent.

Jan 1, 1994

By N Morales, G Nelis

Short-term plans must meet the long-term goals while accounting for shovel selectivity, operational space, and scheduling restrictions. There are several approaches that deal with these issues to deliver a feasible short-term schedule. This paper compares two approaches based on mathematical programming to address the short-term mining cut definition and scheduling in an integrated way. They work by scheduling extraction to comply with long-term production goals, but they differ in how mining cuts are modelled. The first approach schedules Selective Mining Units (SMUs) but aggregates them around predefined locations. The second approach does not work on SMUs; it decides directly what mining cuts are to be used from a pre-defined set of shapes. It assigns a destination and schedules the extraction for the selected mining cuts. We applied both approaches in a real case study to compare their results in terms of profit, mining cut design, expertise needed, profit, and optimisation performance.

Sep 1, 2021

Visit to the Datsun Nissan Company's body pressing and assembly plant at Rosslyn, Pretoria, and the Claremont-Danville Tunnel on 27th February, 1970. The excursion arranged for the 27th February to the Datsun Nissan motor car assembly plant at Rosslyn, near Pretoria, in the morning and the Claremont-Danville tunnel in the afternoon was well supported by some 43 members. The visitors were met at the factory by Mr Rademeyer, the Industrial Relations Manager, and members of his staff and were taken to the artisan training centre for light refreshments. There is a well-equipped training section with an air-conditioned lecture hall; we were told that such training facilities were important because of the cosmopolitan nature of the artisan staff. The visitors were divided into small parties and taken to the tool die and jig-making section, which is perhaps the key department for a factory of this nature. There the many dies for the presses in the body pressing section, as well as the complicated jigs for body welding are made. The technique for making the castings for the dies is interesting. A polystyrene model of the casting is embedded in moulding sand. In a neighbouring foundry molten metal is pressed into the headers and burns away the polystyrene, which leaves no residue, and this exactly fills the space occupied by the model. This rough casting is then machined in large copying machines (costing as much as Rl80 000). An exact plastic model of the surface of the pressing required, set up in juxtaposition to this casting is traversed by a master stylus which operates the slave milling cutter, thereby machining the surface to close tolerances. The machined casting is cleaned up by hand and finally finished in large spotting machines, using a blue dye to show up high spots, to the fine degree of accuracy required. The body pressing section was next visited. There the large number of pressed parts which make up a vehicle body are pressed out of special deep drawing steel plate. Some of the largest presses were capable of applying a pressure of 1 200 tons and cost as much as Rl85 000 each. The visitors then followed through to the assembly section where jigs are used to hold together the many pressings, which are then spot welded into body frames. The frames go to an assembly line where they are finished to the stage for painting. The continuous crawl painting assembly line carries the frames through all the stages of prime coating with zinc phosphate sprayed on in a tunnel, followed by immersion of the lower parts in a priming bath, then drying and spray painting and baking in tunnels. The body frames, after painting, join another assembly line, where the doors, upholstery and many fittings are attached. After this stage the completed bodies are lowered onto and attached to the chassis units which are largely assembled from imported parts (engines, transmission units, etc.). From the end of the line the completed cars are driven off to the trial track and then pass through a tunnel with powerful water sprays to detect leaks in the body work. The proportion of locally made parts is just on 45 per cent. An interesting aspect of the assembly organization is that, of the 140 or 160 cars completed each day there may be included some of each of the Datsun model as well as some Renault and Alfa Romeo models models which are assembled by this company. The change from one model to another several times a day does not present any difficulty to the organization. Each section of the assembly plant 'buys' the units from the preceeding section and 'sells' to the succeeding section. This means that the responsibility of each section ends when the unit is sold to the next section. The cost of repairing any faults found subsequently is charged to the section where it is found, which puts a powerful emphasis on meticulous inspections between sections to safeguard their costs. After the tour the parties assembled at the lecture hall where a lavish cold buffet luncheon was provided by the company. After luncheon Mr A. R. C. Fowler, on behalf of the Institute, thanked the Managing Director, Mr W. J. Wilson and his staff for this most interesting and well organized visit. The party then left for the Claremont-Danville tunnel. The tunnel is being driven by General Mining Federale Kontrakteurs through the Daspoort Range, Pretoria, to link the suburbs of Danville, near Iscor, and Claremont, which at present can only be reached by a nine mile detour. It is estimated that some 6000 vehicles per day will use the tunnel. Before entering the tunnel a short talk was given by Mr Ross who is in charge of operations. He called on various officials and staff of the Consulting Engineering firm, Basil Read (Pty.) Ltd., to describe the tunnel and

COUNCIL AND STANDING COMMITTEES, 1974-1975 Office Bearers : Prof. R. P. Plewman (President), Dr R. E. Robinson and Dr M. D. G. Salamon (Vice Presidents), J. K. E. Douglas (Honorary Treasurer), and P. W. J. van Rensburg (Immediate Past President). Elected Members of Council: Dr M. G. Atmore, E. Collier, G. H. Grange, Dr P. R. Jochens, Dr D. I. Legge, D. G. Malan, C. T. Shaw, L. W. P. van den Bosch, D. A. Viljoen, H. M. Wells, P. A. von Wielligh. Branch Chairmen: B. T. Hosking (Witbank-Middelburg Branch), D. A. Smith (Orange Free State Branch). Past Presidents Serving on Council: R. J. Adamson, M. Barcza (until May 1975), H. Britten, H. E. Cross, Prof. J. de V. Lambrechts (until December 1974), R. C. J. Goode, Prof. D. D. Howat, Dr J. P. Hugo, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 19, and the standing and sub-committees held 74 meetings. COMMITTEE CHAIRMEN Membership, Dr M. D. G. Salamon; Technical Programme-Metallurgy, D. A. Viljoen; Technical Programme-Mining, G. H. Grange ; Vacation School-Metallurgy, Dr P. R. Jochens; Vacation School-Mining, Dr M. D. G. Salamon; Awards, Prof. R. P. Plewman; Excursions, Dr D. I. Legge; Constitution, Rules and Policy, P. W. J. van Rensburg and Prof. R. P. Plewman; Mines and Works, P. A. von Wielligh; Education, P. W. J. van Rensburg. REPRESENTATIVES ON OTHER BODIES Associated Scientific and Technical Societies Members: V. C. Robinson and Prof. R. P. Plewman. Alternates : Dr R. E. Robinson and Dr M. D. G. Salamon. Federation of Societies of Professional Engineers Members : J. K. E. Douglas and P. W. J. van Rensburg. Alternates : Prof. R. P. Plewman and G. H. Grange. South African Council for Professional Engineers Member : R. C. J. Goode. Alternate : G. H. Grange. Engineers' Liaison Committee (Pretoria) Member: Dr J. P. Hugo. Alternate: P. W. J. van Rensburg. MEMBERSHIP Thirteen Fellows, seventeen Members, eleven Graduates, three Associate Members, eighteen Associ¬ates, twenty-six Students, and one Company Affiliate were elected during the year. Nine Fellows, four Members, and three Associates were admitted to retired membership. Eight Fellows were elected to Honorary Life Membership. Three Members and one Graduate were transferred to Fellows, nine Graduates and two Students to Members, six Students to Graduates, one Student to Associate, and one Associate to Associate Member. Six Fellows, ten Members, three Associates, and one Student resigned. A statement of membership as at June 30th 1975 and the end of the previous year is shown in the following tabulation: 30th - 30th June, - June, 1974 - 1975 Honorary Life Fellows - 9 - 15 Honorary Fellows 8 - 8 Life Fellows 170 - 170 Fellows 544 - 536 Members 512 - 523 Associate Members 10 -15 Graduates 130 - 133 Associates 194 - 210 Students 173 -175 Company Affiliates 70 - 71 1 820 - 1 851 [ ] OBITUARIES Your Council records with deep regret the death during the year of the following members: M. Barcza, Honorary Life Fellow and Past President of the Institute; J. A. Boyd, F. E. Keep and J. H. Taylor, Life Fellows; I. D. B. Corner, C. O'G. Deane, R. E. Gilmour, A. C. Hofmeyr, M. W. Howell, T. J. Robin and F. C. Steinhobel, Fellows; J. J. Frankel, Member; T. J. Higgs, Associate. FINANCE The annual accounts, which follow this report, indicate that income again exceeded expenditure by a margin of R21 410 (last year R28 524). This year's income of R71 184 showed a further increase compared with last year's figure of R55 025. Costs, however, also in¬creased, and it is calculated that, excluding non-recurrent costs, the cost of running the Institute in¬creased by R6 654 from R25 501 to R33 155 for the current year. The main increases were involved in secretarial fees, stationery and print¬ing, and in publication of the Journal. All indications are that costs will continue to rise, and we have been advised that the A.S. & T.S. will be increasing their secretarial fees by 25 per cent in the year ahead to meet their rising costs. This year's surplus was derived entirely from the revenue from sales of publications (R13 644) and a surplus from the 1974 Winter School (RIO 654). There can be no certainty that revenue from these sources can be repeated each year. Our funds are in a satisfactory position because of these worth¬while activities, but the administrat¬ion of the Institute should not de¬pend on them. Council will accord¬ingly have to give consideration in the year ahead to an upward adjust¬ment of subscriptions to meet rising costs.

Jan 10, 1975