Search Documents

By A. C. Mulholland

The electrical control of three-electrode submerged-arc furnaces suffers from a number of complexities, mostly due to the nature of the furnace electrical circuit providing power to the furnace where the three electrodes are interconnected within the furnace through the molten metal bath. This gives rise to what is known as the interaction effect 2, where variations in one electrode?s current can cause comparable changes to the currents in the other electrodes, particularly in larger furnaces with low power factor. Resistance-based control of the electrode penetration has largely alleviated these problems, since the resistance encountered by each electrode is predominantly dictated by the length and conductivity of the current path from the electrode?s tip to the molten metal bath, which acts as the three-phase circuit?s floating neutral point. Hence resistance changes due to tip position or conductivity changes beneath one electrode do not affect the resistances beneath the others, effectively decoupling the control of the individual electrodes1. Although resistance-based control is therefore generally accepted as superior to current-based control for the regulation of submerged-arc furnace electrode penetration, a few furnace operators still prefer to use current control under specific furnace conditions. This paper presents the results of analysing the performance of both current and resistance-based control in typical scenarios encountered on industrial furnaces, taking into account a number of factors including electrode penetration, power distribution, efficiency and asymmetry of the electrode currents. In order to accomplish this, three typically encountered scenarios were simulated. The results obtained show that resistance control provides more benefit in all cases, however, the uneven electrode current distribution generated by resistance control when electrodes are on top stops may cause some concern if baking of the electrodes is required in this scenario.

Jan 1, 2009

By A. Tello

Variography was introduced by Dr. Pierre Gy to monitor a process, in the sixties. Later on, Francis Pitard extended this concept, building a complete system of variographic controls for different applications. Nevertheless, the existence of information about its use as a way to effectively control plants has been limited. There are infinite areas where variography and chronostatistics can be used. In this paper, two different cases related to gold and silver recovery, through well known but complex metallurgical routes are studied. The use of effective management of process variability software (EMPV) has shown to be a suitable solution to clarify problems at the plant and, consequently, a solution to the encountered problems has been proposed. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in depth way. Once the ore has been extracted from the mine, sampling is necessary at each sequence of the metallurgical process involved. As a first example, leaching of the ore with cyanide in agitated tanks is another case of a complex metallurgy. The aim of the process is to know about residual values in the tailings in order to optimize process. As a second example, leaching of gold and silver in ore heaps, has to be optimized in terms of time, reagents consumption and, of course, in predicting a reasonable recovery. This last issue appears to be crucial. After cyanide leaching at the heaps, a carbon in columns process is involved, where there are a series of carbon loaded columns that are submitted to a dynamic process of load and unload, to finally deliver an enriched solution to the precious metal electrowinning plant. In both cases, variography has been a good approach to show metallurgists ways to improve the operation.

Jan 1, 2009

By D. Noort, M. Dawborn, D. O. del Castillo

This paper was originally presented at the North American/9th US Ventilation Symposium, June 2002, Kingston, Ontario, Canada. Reprinted with permission of the publishers, A.A. Balkema Publishers, Rotterdam, Netherlands. This paper is a study of the ventilation, cooling and refrigeration system design of the Mindola copper mine in Zambia. The challenges that were addressed varied from the restrictions imposed by an ageing infrastructure to the requirement for increasing the annual production rate, coupled to the introduction of a higher level of mechanization while maintaining acceptable conditions and limiting total ownership costs. A description of how the ventilation, refrigeration and cooling systems were modelled in order to obtain the projected heat loads associated with two different mining methods over the life of the project. The methodology included a number of iterations to optimise the design and include aspects such as the expected inrush of hot fissure water, the operation of diesel machinery at depths in excess of 1500m below surface, developing a cost-efficient cooling strategy and selection of the refrigeration machinery to meet the requirements imposed by the cooling strategy. This paper demonstrates the successful implementation of an integrated design approach.

Jan 1, 2005

By J. P. Gouvea, W. Geel

Resin bolting in South Africa has been developed and refined in underground coal mines (i.e., soft rock) since the late 1940s. The extension of resin bolting to hard rock mines started in 2003 and has required significant adaptations, challenging the status quo from both a supplier and applicator perspective. As far as resin bolting is concerned, the most affected aspect in coal mining and hard rock mining environments, is the rock drills or machinery used for installation. Hard rock mines mostly use hand-held airlegs with limited thrust, low torque, and rotation speed, relative to coal mine mechanised bolters. Resin bolt development for hard rock mines was, and still is today, predominantly focussed on compensating for the ‘shortfalls’ of using hand-held airlegs. At face value, hydro-powered rock drills, which are more powerful than traditional handheld equipment, provided hard rock mines with a means to attain more consistent and reliable resin bolt installations. This paper assesses the quality and performance of hydro-powered resin bolting at an intermediate to deep level platinum mine in South Africa and its potential contribution to rock-related instabilities when applied erroneously. The findings of this paper necessitate a revision of current quality control and quality assurance measures related to resin bolting for underground support.

Nov 24, 2025

By E. Keskinkilic

Drying, calcination, prereduction, and smelting are the main steps in conventional crude ferronickel production. Industrially, these steps are conducted using the rotary kiln-electric arc furnace (RKEF) process. In this paper, calcination characteristics of Sivrihisar laterite ores from the Central Anatolia region are investigated. The extent of elimination of chemically bound water and other volatiles was studied by experiments conducted at various temperatures in the 250?800°C range. Phase changes were examined using X-ray diffractometry. For the particle size used in the study, 300°C was determined to be almost sufficient for complete transformation of goethite to haematite, and 700°C was required for effective elimination of all volatiles in the ore.

Jan 1, 2012

By L. H. Lindstad

The paper reviews the tapping process and the major wear mechanisms on the tap-hole, including wear from tapping tools. Measured temperatures in different tap-holes are related to choice of binder and material for repair pastes. The strength and disadvantage of carbon and silicon carbide materials are compared. Normal daily and weekly maintenance of tapholes is described, together with the major repairs that are done during longer furnace shutdowns. The objective is to show that the type of repair and repair material needs to be adapted to each individual furnace.

Jan 1, 2014

By Z. Gxowa, L. H. Chown, U. Curle, G. Govender

This work evaluates the deformation behaviour, at warm working temperatures, of green particle-reinforced aluminium composites produced by powder blending in a high-energy ball mill. The work focuses on metal matrix composites (MMCs) based on the 2124-Al alloy, reinforced with 10 or 15 vol.% SiC and metal matrix nanocomposites (MMNCs) based on the 2124-Al alloy, reinforced with 5 or 10 vol.% Al2O3. Three batches for each powder were blended and powder properties such as particle size distribution (PSD) and shape were consistent after blending. It was observed that a more uniform distribution of the reinforcement phase in the aluminium alloy matrix was achieved in 2124-Al/Al2O3 than in 2124- Al/SiC composites. The powders (unreinforced 2124-Al and blended) were initially over-aged at 350°C for 2 hours to reverse any natural ageing that may have occurred prior to use. The over-ageing was incorporated to improve compressibility of the powders with the aim of achieving green compacts with higher integrity. Uniaxial compression tests performed at ambient temperature on a Gleeble® 3500 thermomechanical simulator were unsuccessful as the green compacts fragmented. Engineering stress-strain curves showed that green compacts of unreinforced 2124-Al, 10%SiC MMC and 5%Al2O3 MMNC deformed in a similar manner at ambient temperature and had the same compressive fracture stress of approximately 170 MPa. When the deformation temperature was increased from ambient to warm working temperatures (170–280°C) it was observed that electrical resistance heating (the heating mode of the Gleeble®) of unreinforced Al alloy, MMC and MMNC green compacts did not occur. This was attributed to the high electrical conductivity of aluminium, which resulted in poor heat generation due to the low electrical resistance in the samples. It was presumed that the small sample size (d=8 mm, h=12 mm) also caused rapid heat loss. After further experimentation, the green compacts were heated successfully by insulating the samples to retain heat. It was found that at 280°C, increasing the soaking time from 6 to 20 minutes decreased flow stress and improved plastic flow in the 2124-Al/10%SiC green compact.

Jan 1, 2016

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012

By Y. Rajpal

The Hedley and Grant pillar strength formula is widely used within the South African mining industry to calculate pillar strengths in bord and pillar mining layouts, and is currently being used at Bathopele Mine. Bathopele is an operation of Anglo American Platinum near Rustenburg, mining the UG2 reef at depths ranging from 40 m to 300 m below surface. The formula includes a parameter K, which is a downrated uniaxial compressive strength value of the rock, used to calculate the strength of a pillar. At Bathopele Mine, for the shallower areas Less than 150 m the value was 33 MPa, but this was increased to 44 MPa due to the fact that rock mass conditions improved and there were no incidence of failure in the shallower areas. Underground observations showed pillars to be stable with no signs of failure, and it was questioned whether the design was not still too conservative, resulting in sub-optimal extraction ratios and consequently a loss of revenue to the mine. A trial mining section was started at the mine where the pillars were reduced from 6 m x 6 m to 5 m x 5 m and the pillar behaviour was monitored for the onset of failure. Numerical modelling was conducted using the TEXAN code to back-analyse pillar stresses in order to find a more realistic value for K. Results from the trial section indicated that the pillar design was in fact too conservative, and the value for K was adjusted to 54 MPa for future designs. This paper details the findings from underground monitoring and numerical modelling results, and includes details for further calibration of the K value in order to further optimize the extraction of the orebody.

Jan 1, 2012

Dr Hanekom I would like to thank Dr Hanekom for a very valuable -contribution; it summarizes careful statistical test work which was an omission from the original paper. Minor manipulative details, the application of a finer measuring graticule and the reproducibility of the procedure are described and the author accepts with gratitude this ready-made answer to the first and second points of Dr Finkelstein's comments. Mr Williamson The author is indebted to Mr Williamson for historical background to early experiments with captive bubbles and it is conceded that the original paper described another avenue to an old flotation goal. The field of application is restricted and we would not work with all the material illustrated by Klassen and Mokrousov.1 The particles in Figure 74(a) are far too large and irregular; material in Figures (b) through (d) could be employed for semi-quantitative work in spite of obvious disadvantages; Figure 74(f) represents ideal conditions. We have studied this mineral-collector association in the size range given and results were satisfactory. For larger pick-up values than that illustrated an induction period of more than 0.01 second was required (actually 90 seconds for a maximum bubble load at pH 7.2 with 25 g/t oleic acid!). REFERENCE 1. KLASSEN,V. I. ANDMOKROUSOV,V. A., 'An Introduction to the Theory of Flotation,' Butterworths, London, 128, Figure 74, (1963). Mr Slander and Mr Kooij Researchworkers in a practical mineral development laboratory may well ask what contribution yet another micro-technique can make to the problems of large scale ore flotation. The obvious answer is that there can be little or no direct translation of results obtained with a static system comprising air bubble and pure mineral concentrate to a dynamic multicomponent operation. However, for the rapid study of one mineral or variable some small scale apparatus must be employed. In the Anglo American Research Laboratory, the described semi-quantitative pick-up technique has filled a niche and requirement. For ourselves, the system represents a definite advance over the contact angle approach in that samples of minerals conventionally prepared in laboratory or plant may be used, which is a desired step nearer flotation. We bracket this pick-up apparatus with the Hallimond tube1,2 and evidence is now to hand that pick-up curves may often be related to flotation recoveries obtained from this tube with pure mineral samples and from the Fuerstenau glass cell3 with the total ore at low pulp densities. We would not wish to push the comparison of pick-up results past this stage for there is much published development work relating the Hallimond and Fuerstenau equipment to flotation on a larger scale. At the Anglo American Research Laboratory for example, a test in a Fuerstenau cell is often the final integrated step in laboratory investigations into the TORCO process. As these contributors rightly point out, pick-up tests can offer nothing towards the determination of optimum reagent dosage for large scale flotation. This is the function of bench-type flotation cells with up to 2 kg batches of ore. At this level, collector performance and consumption and physical properties of the froth are more comparable with large scale operation. The pick-up cell, Hallimond tube and Fuerstenau cell are essentially equipment from which the effect of control parameters can be derived. For the assessment of collector behaviour, the pick-up approach is rapid and economic and we offer here a pick-up contribution towards the flotation of Witwatersrand uraninite with anionic sulphonate collectors (Fig. 1). A large crystal of the local mineral was not available for contact angle measurements and owing to its low concentration in Witwatersrand gold-bearing reef, a small sample was laboriously obtained by tabling, superpanning and heavy medium separation. The pick-up values of a sized portion were determined by the described procedure in the presence of nine petroleum sulphonate collectors. Responses fell into two categories; "normal" curves (dotted lines) and a group of collectors which were very active at low concentration but showed depression of pick-up at the higher levels. The similarity in form of curves for collectors 1 and 3 was apparent and reagent 3 was found to be simply a diluent of 1. Otherwise, collector performance could not be related to either sulphonate content or molecular weight of the active constituent. However, reagent 2 gave the best performance in a bench flotation cell with regard to overall uranium distribution but, as predicted, reagent 1 yielded the best grades. Later pick-up tests with a similar class of collector have suggested that depression at high reagent concentrations may be due to "bubble armouring" whereby an hydrophilic air-liquid interface is produced which rejects mineral attachment. Prolonged investigations with the same mineral sample have not been required except for the study of uraninite which lasted for more than a year. Variation in pick-up response could not be detected over this period during which the mineral was stored under distilled water. The only visible change was a small efflorescence of lead sulphate, readily removed and decanted off after stirring with a glass rod in the sample tube. In its main role as a "trouble-shooter", the pick-up method is applied to fresh mineral samples taken from a flotation plant and soon discarded or from a current run in the ore-dressing laboratory. After production of a concentrate, a solvent cycle, as described in the original paper, may be required to remove heavy organics or other contaminants as when a sample has been taken from circuits containing detergents, grease or return flotation solutions. This solvent cycle will not remove chemisorbed collectors and we prefer not to work with minerals from flotation tailings or with pick-up cell discards. It has been thought preferable to answer the contributors' other apprehensions with regard to sample preparation, activators, depressants and the physical properties of reagents in another paper on offer to this Journal. It covers pick-up investigations relating to the flotation of nickeliferous pyrrhotite at two Anglo American Corporation Mines, which approach seemed the correct orientation for a reply to another contributor to this paper.

By S-J. Park

When evaluating mining investment opportunities, one should consider the risks associated with mineral exploration and development. These are commonly classified as technical, economic, and political risks, and are accounted for in the investment decision by changing the discount rate. Thus, a company may use different discount rates associated with varying risks in order to compensate for the variability of success. The discount rate has a tremendous effect on the economic evaluation of mineral projects. Even when all other factors used as inputs for calculating the NPV (net present value) are equal, the project under consideration may be accepted or rejected depending upon the discount rate. Determining a realistic discount rate for a given project is therefore the most difficult and important aspect of cash flow analysis. It should be determined with the consideration of proper technical, economic, and political conditions surrounding the specific project undergoing economic evaluation. One key problem for determining the appropriate discount rate is that it typically depends more on subjective perception of the degree of risk or other experience factors than on a systematic approach. Thus, this study aims to identify, analyse, and document the type, role, and impact of risk factors influencing the determination of discount rates, and then to determine discount rate by using the aforementioned factors.

Jan 1, 2011

By L. Thomas, A. Argyn, B. Mbao, G. Longo Banza

Since the first application of solvent extraction as part of the hydrometallurgical processing of copper, several studies have been carried out to optimize extractant formulations. In 2006, Solvay developed the ACORGA® OPT series of solvent-extraction reagents to optimize copper transfer by use of a blended formulation containing both aldoxime and ketoxime as well as selected modifiers. The incorporation of selected modifiers in these blended reagents resulted in increased copper transfer, due to the interaction between the modifier and oximes within the blend. By changing the ketoxime concentration and ratio of modifier to aldoxime, the strength of the formulation was optimized to enhance copper transfer and improve Cu:Fe selectivity. This formulation is well known in the African region under the ACORGA® OPT5540 name and provides the best performance at the conditions of agitated leach plants with pregnant leach solutions that fluctuate in Cu grade and pH. This paper discusses advantages of using ACORGA® OPT5540 in the Copperbelt

Jan 1, 2023

By S. Andika, O. A. Putri

Maintaining fleet productivity, which consists of balancing loader and truck performance, has always been a challenging task. An automatic dispatching system (ADS) is implemented to help monitoring fleet condition and assign trucks to a designated loader. Integrated data from real time Global Positioning System, Vehicle Health Monitoring System, and other production related data are acquired to support the ADS. However, the abnormal truck cycle has been the main culprit which resulted in unnecessary loader hanging time and trucks queuing time. Hanging and queuing time accounted for 2.34 and 2.07 minutes respectively per loading cycle or equal to 2,861 loose cubic metres per fleet per day production losses. Using integrated dispatching system data, the authors conducted research to study a truck’s hauling cycle that affects fleet productivity. The data is modelled to obtain the arrival rate pattern in a front loading area by adopting the queue theory algorithm. This paper aims to understand the potential pattern of a truck’s cycle abnormality and to resolve its occurrence.

Sep 1, 2021

By O. S. Tinkler, K. C. Sole

Approximately 20% of current world copper cathode output is produced using a hydrometallurgical process route, generally referred to as the leach–solvent extraction–electrowinning flowsheet. Since its commercialization in the late 1960s, steady improvements in the performance and efficiency of the solvent-extraction reagents and equipment, combined with significant developments in leaching and electrowinning, have made an ever-widening range of ore types amenable to this technology. Following successful implementation on all major continents, a large proportion of growth in recent years derives from the re-emergence of copper solvent extraction in the Central African Copperbelt. This review provides a brief history of the development and evolution of copper solvent extractants and mixer-settler contactors, and the significance of the Copperbelt region in achieving commercialization and acceptance of the technology. The opportunities and challenges presented by the abundant high-grade oxide ores of the Copperbelt are contrasted with the processing of solutions derived from the low-grade mixed oxide–sulfide ore bodies that are prevalent in other geological regions. The current status of hydrometallurgical copper production in the African Copperbelt, within a global context, and a medium-term outlook for the technology are discussed.

Jul 5, 2023

By B. Matsetela, S. Amos, V. Nkuna

"The Kamoa-Kakula copper project—a joint venture between Ivanhoe Mines, Zijin Mining Group Co. Ltd, and the government of the Democratic Republic of Congo—has been independently ranked as the world's largest undeveloped high-grade copper discovery by international mining consultant Wood Mackenzie. It is a very large, near-surface stratiform copper deposit with adjacent prospective exploration areas within the Central African Copperbelt, approximately 25 km west of the town of Kolwezi and about 270 km west of the provincial capital of Lubumbashi. A phased development approach is currently envisaged. The first phase of the project involves the development of a 6 Mt/a underground mine and surface processing complex (dual stream concentrator) at the Kakula deposit, a discovery announced in early 2016. The second phase involves an integrated 12 Mt/a two-stage development, beginning with initial production from the Kakula mine, to be followed by a subsequent, separate underground mining operation at the nearby Kansoko mine, along with the construction of a smelter. Project description and locationThe Kamoa–Kakula project comprises a newly discovered, very large stratiform copper deposit with adjacent prospective exploration areas, located within the Central African Copperbelt in Lualaba Province, Democratic Republic of Congo (DRC). The Kamoa–Kakula project lies approximately 25 km west of the town of Kolwezi and about 270 km west of Lubumbashi. Ivanhoe owns a 49.5% share interest in Kamoa Holding, an Ivanhoe subsidiary that currently owns 80% of the project. Zijin Mining owns a 49.5% share interest in Kamoa Holding, which it acquired from Ivanhoe in December 2015 for an aggregate cash consideration of US$412 million. The remaining 1% interest in Kamoa Holding is held by privately-owned Crystal River.The Kamoa–Kakula project consists of the Kamoa exploitation licences (exploitation permits 12873, 13025, and 13026, which cover an area of 397.4 km2) and one exploration licence (exploration permit 703 covering an area of 12.74 km2). The Kamoa exploitation licences, approved 20 August 2012, grant Kamoa Copper the right to explore for, develop, and exploit copper and other minerals, for an initial 30-year term, expiring on 19 August 2042. The permits can then be extended for 15-year periods until the end of the mine’s life."

Nov 1, 2018

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

By J. Rabe

Tasked with developing a flow sheet for a new resource, one typically turns the experts for help. The advice of an expert can be invaluable in reducing the time and costs associated with characterizing an ore (not to mention extracting maximum information from limited samples). While guiding and optimizing a metallurgical concept study requires a certain skill set, selling a project is something different. The metallurgical specialist is usually not responsible for sharing the results of investigations with potential investors. However, the person responsible for selling the project can ensure that a metallurgical concept study is conducted thoroughly and responsibly without having the ability to do the work, while being sufficiently familiar with the metallurgical aspects to authoritatively sell the project. The process of identifying suitable process routes through to constructing a concept flow sheet and mass balance is discussed as a basic example. From basic mineralogical information and a thorough literature survey, the most likely beneficiation routes can be identified and targeted testing conducted. The final top size will depend on the required product properties (mainly grade), the selected beneficiation technology, and the ore?s liberation properties. Once the required top size has been identified, comminution options can be evaluated. Once again, literature surveys can be used to supplement concept-level comminution property information, and select possible equipment and circuit configurations. Marketing, material handling, and logistics-related information can be used to determine required dewatering technologies. At this stage, enough information is available to develop a concept mass balance and conduct basic equipment sizing..

Jan 1, 2014

By A. V. Wilke

The metallurgical balance is a tool usually applied in the mining industry. The final result is used for different objectives. All the existing software for the calculation of the metallurgical balance fits the numbers in such way that a logical correspondence between the input and output materials exist. Nevertheless, the accuracy of the metallurgical balance strongly depends on the quality of the input data. Division El Teniente of Codelco Chile has been optimizing the metallurgical balance system the last 14 years. As well, it has participated in the development of corporate norms to optimize the operations of sampling and weighting systems. As a consequence, the precision and the accuracy of the metallurgical balance have been improved in a significant way. Also the understanding of process variability was enhanced. The improvements have allowed Codelco to discover and minimize hidden losses and to better support top management decisions. The present paper describes the main aspect of the continuous improvement process.

Jan 1, 2009

By G. E. Rencken, J. H. Potgieter, A. Narain, J. Smith

To conserve fresh water resources and comply with environmental regulations, DRDGOLD, a South African gold producer re-treating surface tailings, has transitioned to a fully closed water circulation system. Consequently, the accumulation of contaminants, as well as addition of reagents, has led to changes in water composition that have compromised leach performance and overall gold recovery. A two-sample t-test confirmed a significant difference in gold recoveries between the use of Rand Water, which was used as a benchmark, and untreated process water. Atomic absorption analysis of ERGO’s process water, confirmed the presence of iron, nickel, zinc, and manganese. A study of the effect of the identified contaminants on gold recovery showed that iron, nickel, and zinc have the largest negative effect on gold recovery, with iron and nickel being more detrimental than zinc. Sulphates were shown to have a possible passivation effect, which also influenced gold recoveries, although to a lesser extent than the heavy metals. Calcium, when present in excess, had a positive influence on gold recovery indicating the possible formation of a calcium aurocyanide complex. Lime softening successfully reduced the heavy metal and sulphate concentrations, and the gold recoveries obtained with the treated process water were similar to those as achieved with Rand Water.

Jul 1, 2021

By T. B. Beeton

In view of the limited reserves of good-quality coking coals in South Africa, Iscor has been involved in direct reduction since the middle sixties. Since the early seventies, its interest in direct reduction was stimulated further by a swing towards' continuous casting, which, in turn, contributed to a shortage of the scrap supply for electric-arc-furnace (EAP) steelmaking. Rock engineering The First International Conference-Rock Enginet:ring and Excavation in an Urban Environmentorganized by The Institution of Mining and Metallurgy and the Hong Kong Section of the Institution, in association with the Hong Kong Institution of Engineers, will be held in Hong Kong from 23rd to 28th February, 1986. SPOTLIGHT on Gold Fields National Engineering Awards For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984.

Jan 1, 1985