Search Documents

By E. W. Dean

The Bureau of Mines is engaged in the work of obtaining data regarding the physical and chemical properties of typical crude oils from the various producing fields of the, United" States. Preliminary reports have been published that cover the eastern fields* and the' Rocky Mountain districts.** Since the appearance of these, reports: it has been suggested that certain additional data. I regarding the samples would be of practical value. It was believed that a knowledge of the viscosity of crude oil was desirable, particularly in connection with the design and operation of pipe lines. In accordance with this suggestion, the authors have made viscosity tests upon as many of the samples of the two series as wore still available for examination. Determinations were made at temperatures of 70° and 100°F., and in addition the oils were Subjected to the A. S. T M, pour-test*** to as certain the lowest temperatures at which they remain in a fluid condition.

Jan 1, 1921

By R. D. Leitch, W. P. Yant

"In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information- as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report.The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. .Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and to others for information received; and to Dr. R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.The Lower Kittanning is the most important bed in the locality studied. A great many of the abandoned mines examined are in this bed, and nearly all of the present active ones are. The Upper Freeport bed is also mined to some extent, and a number of the abandoned mines formerly worked this bed. As only three active mines are now (1927) working the Upper Freeport, the comparison of acidities is necessarily limited. Of these three, one had been idle since 1922 until shortly before it was sampled.The location of most of the mines was already known from previous work, but some of them had to be located by following up streams known to contain acid waters. A sample of the- outflow was collected in self-sealing bottles known as ""citrate bottles"" for the determination of dissolved oxygen by the Winkler method.5 Another sample was taken for the determination of acidity according to standard methods of water analysis.6 Ferrous iron was determined at the mine or very soon after taking the sample by titrating with a standard solution of potassium permanganate in acid solution. The hydrogen-ion value was determined by a standard double-wedge comparator.7From the total acidity values in each sample, which are the most important values, the total iron was calculated on the assumption that acidity as sulphuric acid was due to dissolved ferrous sulphate. This assumption is commonly made for mine waters, but is inaccurate to the extent that free acid is already present, and some of the iron is present as ferric, rather than ferrous, sulphate. The amount of ferrous sulphate may be a rough measure of the extent to which oxygen is lacking within the mine. The permanganate titrations just mentioned showed what part of this total iron was in combination as ferrous sulphate, and the difference .was assumed to be that in combination as ferric sulphate, after correcting for the amount of free acid already formed as shown by the titration values."

Oct 1, 1928

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950

By Warren E. Morrison

Demand for energy in the United States in 1965 was stimulated by the continuing expansion of the economy. A gain of 5.9 percent in gross national product for the year was accompanied by a 4.4-percent rise in energy consumption. Domestic energy resources met about 93 percent of the nation's requirements. The remaining 7 percent consisted of imported fuels, mainly of crude petroleum and residual fuel oil. The major fossil fuels-natural gas, crude petroleum, and coal, in that order-contributed 96 percent of all commerical energy utilized, with the balance of 4 percent being primary electricity from hydropower and nuclear power plants. Production was up for all of the major mineral energy resources in 1965, with the single exception of anthracite, output of which continued to decline. Bituminous coal output for the year was 512 million tons; marketed production of natural gas, 16,039 billion cubic feet; and crude petroleum output, 2,848 million barrels. Among the secondary products processed from primary energy resources, the most significant gains were in coal carbonized for coke which increased 6.7 percent to 95 million tons, and in the output of liquefied gases from natural gas which rose 4.8 percent to 11,257 million gallons (268 million barrels). Within the latter category, the off? take for petrochemical feedstocks continued to rise at a very rapid pace.

Jan 1, 1967

By D. B. Dow

This report on methods employed for dehydrating oil-field emulsions, is the second of a series prepared as a result of a study of oil-field emulsions recently completed by the writer. The first paper2 dealt with the factors responsible for the formation of emulsions. A third paper will discuss the physical chemistry involved in the formation and resolution of such emulsions. In the early development of the oil fields of Pennsylvania, no emulsion troubles of any consequence were encountered, nor to any serious extent in the oil fields of other Eastern States: However, with the development of fields west of the Mississippi in Oklahoma, Kansas, Texas and California, where heavier oils of different characteristics were found, the problem of dealing with cut oil soon became of great importance.

Jan 1, 1925

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK – ALTMETER SURVEY WITHOUT PLTTMETER TEMPERATURE CCRRECTION DATA INPUT

Jan 1, 1977

In the U.S. coal mining industry, a large cohort of miners is at or nearing retirement age. As these miners retire, there will be a need to hire and train thousands of new and most likely younger workers. Moreover, a large portion of safety trainers will also require replacement due to retirement. In a speech before the U.S. House of Representatives (2004), Bruce Watzman, Vice President for Safety, Health and Human Resources for the National Mining Association said, “[W]e will need to replace a major portion, approximately 50%, of the underground coal mining workforce within the next 5–7 years.” The large influx of new mine workers, along with the deficit in safety trainers, creates the challenge to provide consistent and effective safety training. Given the expected high turnover of the mining workforce, it is very likely that incoming workers will have much less experience than those leaving the workforce. Unfortunately, inexperienced miners have been shown to incur the highest rate of injuries. The piece of machinery most associated with these injuries is the roof bolting machine, which accounts for 56% of machinery-related injuries in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) has released a new report entitled “Roof Bolting Machine Operators Skills Training for a Walk-Thru Roof Bolter: Trainer’s Guide” (IC 9489). It is designed to help safety trainers develop struc-tured training for new operators of walk-thru bolting machines. This resource will help trainees learn, understand, and apply knowledge and skills. Included in the trainer’s guide are the following tools: [ ] a six-part DVD video series, a skills check survey, talking points, and a complete job training analysis. Also included is an exercise to help trainees learn more about their mine’s roof control plan, as well as a list of supplemental training and reading materials. On-site trainers can modify this guide to fit their particular mine conditions, machines and equipment, and work procedures. The goal of every coal mine safety professional is to increase safety awareness and make mines a safer place to work. The Walk-Thru Bolting Machine Trainer’s Guide will help teach new miners skills to create a safer working environment that will ultimately prevent or reduce on-the-job injuries. Safety trainers can also use the ideas and concepts from this guide to develop their own training skills for the safe operation of other pieces of underground coal mining equipment.

Jan 6, 2007

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 29,020 acres of the 43,165-acre Terry Badlands Wilderness Study Area (MT-024-684) in order to evaluate its mineral resources. Within this report, these 29,020 acres are referred to as the study area. Located in Custer and Prairie Counties, MT, the study area is about 2 miles northwest of Terry. The study area is underlain by essentially flat-lying units of the Fort Union Formation of Paleocene age with some Quaternary alluvial deposits in stream valleys. No mines or prospects were found in the study area. Bentonitic clays and lignite coal units were examined and sampled; however, no clay resources or coal reserves were identified. Estimates of coal resources will be reported by the U.S. Geological Survey in a joint U.S. Geological Survey-U.S. Bureau of Mines publication. Gravel along the Yellowstone River, a source of agate for private collectors, could also be used as sand and gravel aggregate although material on the south bank of the river is closer to population centers and road systems. Clinker found in the study area could be a source of road metal, but is not well situated in relationship to areas of use. No geothermal resources have been identified although water suitable for direct heat applications may underlie the study area. All the area is leased for oil and gas exploration.

Jan 1, 1985

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This article focuses on U.S. Bureau of Mines (USBM) and National Institute for Occupational Safety and Health (NIOSH) research to examine factors that had a significant influence on mine face ventilation design during the past century. Several "milestone" events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative face ventilation designs and a consistent commitment to mining health and safety. Ventilation has always been a concern in underground coal mining. For many yeas, there was no appreciation of how ventilation could be used to remove harmful contaminants from the air or how to control airflow quantities. The first known problems with ventilation date back to the 14th century, when it was recognized that lack of air was a major impediment to the expansion of mines. The common method of solving ventilation problems at that time was to abandon the existing mine and start a new one nearby. Ventilation in the early days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings. Later, in the 18th and 19th centuries, a furnace was introduced underground to increase the updraft in the return shaft. This allowed for a larger quantity of air in circulation. When mines went deeper and became larger, mechanical ventilation became necessary and was first accomplished by steam-driven fans. These fans became more prevalent as furnaces were prohibited in underground mines, especially after the Avondale disaster in Pennsylvania in 1869 (Roy, 1876). Eventually, these fans were replaced by more powerful, electrically [ ]

Background Carbon monoxide (CO) is an odorless, colorless gas that can cause illness and death by asphyxiation. Although the toxicity of CO is understood, CO exposure can occur from unrecognized sources. On April 2, 2000, a couple and their newborn infant were poisoned by CO migrating through the ground from blasting at a nearby coal strip mine into their home near Kittanning, Armstrong County, PA. They were treated at the hospital and diagnosed with CO poisoning. The infant had a carboxyhemoglobin level of 31%, the father 28%, and the mother 17%. Carboxyhemoglobin is the compound formed in the blood when CO is breathed. Persons not exposed to CO have carboxyhemoglobin levels of 0.3%-0.7%, and cigarette smokers have levels of up to 9%. Following release from the hospital, the family installed a CO detector in the basement of their home with the help of the local fire department. This Technology News briefly describes this incident to help increase awareness of the problem. It is discussed in more detail by Eltschlager et al. [2001]. Figure 1 shows the coal strip mine believed to have generated the CO. The initial suspect for the source of the CO was the furnace in the house. Only later did it become apparent that blasting at the nearby strip mine might be the culprit. A State investigation concluded that CO had migrated approximately 500ft from the blast, through the ground, and into the home. Figure 2 shows the locations and order of blasts at the mine. Initially, the mine did not plan to blast. Overburden generally consisted of weathered shale that could be dug without blasting. However, the mine decided to blast when hard sandstone that could not be dug out was encountered within 3 ft of the coal top. The blasting was intended to break up the sandstone. Blasting was done using bulk ammonium nitrate-fuel oil (ANFO) in 6.25-in holes 25-30 ft deep on a 16-ft by 16-ft pattern, with charge weights ranging from 17 to 170 lb. The closest blast to the home was 430 ft on April 17, 2000. The distance from the home to the blast area on the day when CO was first reported (March 31, 2000) was 500 ft. Twenty blasts were detonated at the mine between March 7, 2000, and April 20,2000. The blaster was careful to prevent fly rock since another home was only 150 ft away and a garage was 50 ft away. The quantity of explosive used in the blasts was sufficient to break the sandstone, but was less than would normally be used to blast overburden. The holes were typically one-third explosive and two-thirds stemming, with powder factors averaging 0.43 lb/yd3. Additionally, the muck was not immediately excavated after each blast. The heavy confinement on the explosive acted to prevent the typical release of blasting fumes into the atmosphere. Instances of CO migrating from blasts into homes have occurred before, but generally the distances involved were under 150 ft. It is believed that the blast design contributed to the confinement of CO in the ground, and discontinuities in the ground strata facilitated migration toward the residence. Upon inspection of the blast pitwall, a regular system of joints was observed. These joints are oriented roughly from the blast pit toward the house (figures 3-4).Blast-generated CO appears to have been driven into the joint system, displacing the air. When the joint system was saturated, the next succeeding blast pushed the CO into an uncased well next to the house (a high level of CO has been measured in the well shortly after a blast). From there, the CO entered the French drain system and then the basement of the house. The joints are vertical cracks through rock layers that occur on a regular spacing (figure 3). They are most common near valley slopes and are caused when valley walls converge as the stream cuts down through the rock layers. Often called hill seams, they roughly parallel the valley walls, but can curve and split, creating a pathway for gas movement (figure 5). These fractures are often encountered when underground mining proceeds close to outcrop. The system of fractures at the Kittanning blast pit was well developed and provided a path for transmission of CO both through the sandstone and up and through the overlying shales. Blasting engineers should be able to distinguish naturally occurring fractures from blast fractures and note the frequency, development, and orientation of the hill seams and their proximity to occupied houses. The limits of transmission of

May 1, 2001

By R. V. Ramani, P. M. T. White, D. Sutton

5.1 Incorporation with the Master Design Simulator Figure 1 diagrammatically illustrates the interaction between the various sub-systems that go to make up the total Master Design Simulator. As a total system, all sub-systems will be scheduled as needed by the controlling program. The data require¬ments for each will be made available either by providing common storage in core or by outputting data to external storage devices such as magnetic tape, disk, drum, etc. The incorporation of the Geology and Reserves sub-system into the total system involves the establishment of an interface through which data may be readily dissemminated in either direction. This interface will be provided by a geological data library in which all information available from the sub-system is stored and can be readily accessed by the main program and/or other sub-systems. In Figure 7, the information flow between the Geology and Reserves sub¬system and other sub-systems is shown. 5.2 Independent Function Geology and Reserves sub-system is capable of functioning as an independent unit or in direct communication with another sub¬system. This is possible by either continued use of the data library or by redirecting output to other peripheral devices separate from the total system libraries. (Figure 8).

Jan 1, 1974

By Wesley A. Grosh

The Sutherland copper prospect is situated in Floyd County, Va. The immediate area was prospected around 1850, and one of the adits possibly dates from that time. Little or no ore has been mined from the deposit. The deposit is a mineralized sulfide zone occurring in mica schist and consisting mostly of pyrrhotite with minor amount of copper. A magnetometer survey of the deposit by the American Metal Co. in 1939 showed an anomaly that was thought to indicate a zone: of secondary enrichment. The Bureau of Mines diamond-drilled 14 holes, totaling 913 feet, and opened an adit during February and March 1943. No appreciable copper values or indications of secondary enrichment were found.

Jan 1, 1948

The dust exposure of the longwall shearer operator is usually determined by his position relative to the cutting drums. The dust generated during cutting may travel up-wind, against the primary airflow, and be carried out into the walkway where it can contaminate the intake air for as much as 10 feet outby the shearer operator's controls. Thus, both head and tail drum operators are exposed to un-acceptably high levels of air-borne respirable dust. One Solution The latest generation of long-wall shearers has features that make the use of radio remote or umbilical (hard wire) remote control relatively easy to implement. Remote control can enable shearer operators to control machines from positions that are less dusty than normal control stations. With either type, the head-drum operator can now control the shearer from a position up to 20 feet on the intake-air side of the shearer, while the tail-drum operator's station is now located across from the head drum.

Jan 1, 1984

By John R. Reeves

The development of an new industry, which must prepare its marketable products at or near the source of the raw material, and ship them to a market which may cover half a nation, is more or less influenced by a number of natural and cultural conditions such as (1) location of plants with respect to a large market, (2) climatic conditions, (3) transportation facilities, (4) labor supply, and (5) water supply. An effort is made in this pager to give in detail a number of the more important of these conditions as they affect, either favorably or unfavorably, the development of the oil-shale resources of southeastern Indiana. The utilization of the New Albany formation for the production of oil will be similar to a large scale low-grade ore proposition in which the raw material can be obtained in very large quantities at a relatively low cost. It appears, therefore, in considering the value of this shale or its economic position in relation to other oil shales, tie cost of mining and preparation for the retort are of prime importance.

Jan 1, 1923

By Owen W. Terry

During the summer of 1943 the Bureau of Mines conducted an investigation and program of churn drilling on the McIlhon and adjoining Pearson land in the Mineral Point district of Iowa County, Wis. Sixteen holes, aggregating 1,570 feet .of bore, were completed. The work was undertaken as part of a general investigation of the zinc-and lead-producing area of southwestern Wisconsin at a time when great effort was being made to increase the production of Metals important to the war program. The Bureau's drilling program supplemented a previous drilling pro-gram conducted by the Vinegar Hill Zinc Co., and demonstrated the presence of a strongly mineralized zone at relatively shallow depths.

Jan 1, 1948

By James L. Hendrix

A study was made of the United States Bureau of Mines' chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and IT mechanisms involved in the reactions betweens sphalerite, and galena with chlorine. The influence of copper on the extraction rates was also studied. It has been shown the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373K with the rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1980

By Bill M. Stewart, Phil W. Patton, Curtis C. Clark

Back injuries from handling materials in underground mines continue to be a major safety problem. In spite of the ingenuity of many people and the development of numerous mechanized aids, the number of materials-handling injuries remains second only to the number of roof fall injuries in underground coalmines. Relocation and repositioning of electrical cable, conveyor belt parts, and roof bolt sup-plies in particular are the sources of significant numbers of back injuries. To help reduce such injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are examining Mine Safety and Health Administration accident data to determine correlations between materials-handling tasks and the number of back injuries. Also being investigated are new technologies used in underground mines in the United States. Equipment is being developed or modified that would replace the necessity of doing lifting tasks manually. A Coleman manipulator was tested, and modifications were made to make it more suitable for underground mine use. To reduce or eliminate the need to manually clean off materials that commonly plug grizzly openings, a track-guided pincher arm device was developed. Oversized rock can be broken with the pincher arms in the up position, and the arms can be lowered to grab and remove debris. The arm can also be used in a sweeping action to remove cohesive fines that may bridge grizzly openings.

By Byron. O. Pickard

"An Arizona mining company recently demonstrated a new use for the geophone by successfully locating leaks in compressed-air lines which were buried under from 1-1/2 to 2-1/2 feet of fine rock fill. The following information is abstracted from data sent to the Bureau of Mines by the superintendent of the mine.The company has two parallel main compressed-air lines, about one and one-half miles long, buried under an average of two feet of fine rock fill. One of the lines is a four-inch high-pressure (1000 pounds) main, and the other line a ten-inch low pressure (90 pounds) main. The two mains are separated by a 10 to 3C foot interval, and run from the compressor plant to the No. 2 shaft, where they are taken underground. A pump line is also buried in the immediate vicinity.Several leaks, not audible enough to be located, were developed in the Alms. Various =Abode were suggested that did not seem practicable to the management. Finally, the company obtained a Bureau of Mines' geophone and experimented with it. The first test& were conducted while the pumps were running, and while there was noise on the concrete pavement, all of Which caused so much vibration in the geophone that it was impossible to detect the leaks.The second attempt was made at the close of the day shift when the compressors were not operating and when the pumps could be shut down. The valves in the far end of the surface lines were closed, and the lines were pumped to full pressure (90 and 1,000 pounds respectively).Geophone readings were then taken at 7 or 8 foot intervals directly see the lines. Several leaks some very large in the high-pressure line were audible with the geophone at distances varying from 15 to 30 feet. A con-le leak in the low-pressure line was found at a distance of 10 feet. detecting the leaks, no difficulty was found in locating them exactly. ""At this time"", laid the superintendent of the mine, are unable to large a leak must be in order to be located under two feet of loose geophone. The fill we worked over was quite loose and dry and unfavorable for the work in question. However, we have no that the instrument is a valuable adjunct to our business""."

Aug 1, 1922

"While control of dust-related diseases, the objective of the Generic Mineral Technology Center for Respirable Dust, is of prime importance from the human standpoint it is also essential to the economic well-being of the mining industry (FIGURE 23). Although significant progress has been made, the problem continues to be a major concern to the mining community. An increasing global demand for coal and other minerals means that production and the number of miners employed is on the rise. Therefore, the importance of this research to the mining industry cannot be overemphasized.The five areas of dust research are 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. Some experimental projects where the research is conducted almost exclusively in the laboratory may still rely on industry for imput. No industrial resources are necessary to the research of the non-experimental projects, for example computer modeling .The remaining research is classified as experimental and these projects do require interaction with industry in varying degrees. Periodic trips to mining sites in Western Pennsylvania, Southern Ohio, and West Virginia are necessary to record measurements or collect samples. Or companies may provide needed samples or equipment to the university for use in the laboratory. On several projects interaction is limited to advice or information supplied to the researcher by industry personnel."

Aug 31, 1989

By Erle C. Donaldson

The pendant drop interfacial tensiometer is being used to study interfacial phenomena that influence the production of crude oil. A description of the instrument showing the modification of the cell and cell holder is presented. The modified cell and cell holder allow formation of a precise and reproducible drop size, and the image of the drop is easily alined and focused. Interfacial tension measurements and observations of film formation can be conducted at various temperatures with the jacketed cell.

Jan 1, 1967