Search Documents

By A. W. Khair, M. Ahmad, Gehi. L. D.

"This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.INTRODUCTION Research has reduced the prevalence of Coal Workers Pneumoconiosis from 15 to 5 percent according to NIOSH reports (Breslin 1982). However CWP still have not been eliminated as a hazard to mine workers. To prevent coal workers from having black lung MSHA has established a very strict standard for coal mine operations (2.0 mg/m3 with silica content equal to or less than 0.1 mg/m3,). There are numerous coal operations still experiencing great difficulty with meeting the 2mg/m3 dust standard. Among these are the longwall sections and continuous mining sections. In order to meet the rising demand of energy and coal, the number of longwall operations and continuous mining operations would have to be increased. Thus a long term research commitment is required to develop basic solutions that are more generic and greater benefit to the mining and mineral industry.In continuous-mining operations, the miners are exposed to the dust produced during the fragmentation of the coal from the face plus the dust produced during loading and transferring of the coal. The fragmentation process generates most of the respirable dust. The amount of dust generated during fragmentation depended on the coal properties, cutting parameters and cutting bit configuration. Bit wear changes bit configuration, therefore, it also affects dust generation. Bit wear can be defined as the removal of material from surface as a result of mechanical action. In soft coal mines bit wear may not be a serious problem but in hard coal seams bit wear is very significant. In addition, as the good coal seams are depleted, the operators are mining thin seams and the seams with rock partings. During cutting these seams operators are sometimes forced to cut roof and floor rock or rock partings which result in more rapid wear of bits."

Nov 1, 1995

By H. M. Cooper, R. F. Abernethy

Determination of the fusibility of coal ash consists in melting a pyramid of the ash to fluid under prescribed conditions . The conditions of the test are specified by the American Society for Testing Materials4/ and must be adhered to strictly if comparable results are to be obtained . The Society formerly specified a particular type of furnace , but with improvements in design of both electric and gas furnaces , it was decided by the Society to specify only essential details of the test . The Chairman of Committee D - 5 , Coal and Coke , of the American Society for Testing Materials suggested that the Coal Analysis Section of the Bureau of Mines conduct a cooperative investigation on the effect of furnace type and atmosphere upon fusibility of coal ash . The Coal Analysis Section enlisted the aid of a number of laboratories using the more common furnaces to cooperate in the investigation . Four types of gas furnaces burning natural and manufactured gases and two types of electric furnaces with different methods of maintaining a reducing atmosphere were employed . The results from the survey are tabulated herein , and some comparisons are made . There were not enough data from any particular furnace and atmosphere to make a reliable statistical analysis . However , definite tendencies are evident , and attention is called to them by direct comparison. in tables .

Oct 1, 1943

By S. Benedict Levin

The Big mine has been a source of mica and high-grade felspar from separate zones in the same pegmatite dike since 1914. In 1943 it became the outstanding producer of strategic mica in New England. The urgent need for sheet mica led to core-drilling by the Bureau of Mines from February to May 1914. Nine diamond-drill hob's aggregating 1,474 feet in length were drilled by the Bureau of Mines with the objective of developing extensions of the known mica shoots. The use of large-diameter bits made it feasible to obtain reasonably reliable results in diamond-drilling this type of deposit.

Jan 1, 1949

By R. R. Wells

This report summarizes the results of laboratory testing of copper-bearing magnetite ore from the Poorman, Bush & Brown, and Copper Center deposits, Kasaan Peninsula, Prince of Wales Island, southeastern Alaska. The ores contain minor amounts of chalcopyrite and pyrite. Intimate association of these sulfides with magnetite necessitates fine grinding for adequate liberation and rejection of copper and sulfur and for the production of high-grade iron concentrate low in objectionable impurities. Laboratory tests indicated that the optimum results can be obtained by flotation of ore ground to minus-100-mesh, with subsequent wet magnetic separation treatment of the flotation tailing. A summary of results obtained by this treatment of the three samples tested is shown in table 1.

Jan 1, 1957

By F. Chen, L. J. Gaydos, D. C. Kuhn, Demersm L. M., S. C. Sun

"Summary: In this report the differential regulation of NF-KB and nitric oxide (NO) was investigated in the mouse macrophage cell line RAW 264.7 following exposure to a mineral dust (silica) and /or an endotoxin (Lipopolysaccharide, LPS). The results indicated that silica and LPS can significantly induce the activation of NF-KB as well as elicit enhanced production of NO in RAW 264.7 cells as part of an early inflammatory response mechanism. A 24-hour time-course study showed that NO release from these cells continued to increase following the initial stimulus by LPS or silica. In contrast, activation of NF-KB was maximal at 6 hours and then showed a steady decline to 24 hours. The production of NO was suppressed by protease inhibitor and antioxidant, both of which block the activation of NF-KB. Surprisingly, the use of an NO synthase inhibitor resulted in an enhancement of NF-JCB activation. These findings suggest that NO produced in macrophage cells in response to an inflammatory stimulus like silica or LPS my be linked to a negative feedback role on the activation of NF-KB. It is now accepted that nitric oxide (NO) plays a pivotal role in the inflammation response process when macrophage cells are activated by a pro-inflammatory stimulus (l). Production of NO is dependent on the activity of the enzyme nitric oxide synthase (NOS). Up until now, at least three distinct genes have been described which encode different isoforms of NOS. NOS has been cloned from a variety of different mammalian cells, including constitutive neuron NOS, constitutive endothelium NOS and inducible NOS (2). Macrophages appear to be the principal cellular source for the inducible form of NOS (iNOS) activated in response to an inflammatory producing event. The mechanisms subserving the regulation of the iNOS gene and NO production have been under intense investigation in recent years (3-5). Several binding sites for transcriptional factors have been identified in the promoter region of iNOS gene, including NF-lCB, AP-1, NF-IL6, Oct-I to cite a few (5). NF-KB appears to play a"

Dec 1, 1996

By J. W. Town

The Bureau of Mines conducted phosphate beneficiation studies to determine the influence of mineralogical and textural features on the recovery of phosphate from select bed and composite samples representing different phosphate rock types of the western Phosphoria Formation. Batch heavy-liquid tests showed that ore grade) pellet size, and type of interstitial material were significant parameters affecting concentrate grade and recovery. Recoveries at acid grade (31.5 percent P2O5) ranged from 98 to 56 percent. Liberation was essentially complete at 28 mesh, and recoveries tended to drop when overgrinding occurred.

Jan 1, 1966

By R. V. Ramani

"In Part 1 of this two-part paper the characteristics of mine disasters and their effects are presented with case studies from coal, metal and non-metal mines leading to an amplification of their causes and opportunities for control. The disasters discussed encompass those which threaten the health and the safety of miners and those which affect the general population. In Part 2 of the paper, which will be published in the November 1995 issue of Natural Resources Forum, the approaches to hazard and disaster control are reviewed with particular attention to laws and regulations to promote health and safety at the workplace, and general welfare in mining communities. Further, a systems approach to disaster control is outlined.The mining industry is one of the three basic industries the other two being agriculture, and wildlife and fisheries. It is the process of mining which makes available the riches of the earth - the energy and mineral resources - to benefit humanity. In fact the progress of the human race through the ages is indelibly attached to prowess in exploiting these riches. The stone, iron and bronze ages are markers not just of a time in history but achievements of monumental proportions in the mining and beneficiation of natural resources. Even in agriculture, the remarkable success stories are associated with the prudent use of mined products to enhance production and productivity. The significance of a thriving mining industry to the wealth and security of a nation is therefore unquestioned.Unfortunately, the public's image of the mining industry is often associated with the mining disasters which receive wide coverage in the local and national media. Mine disasters command tremendous attention because of their infrequent occurrence and the extent of human suffering involved. Whether it is an explosion or a fire, or the opening or closing of a mine, the lives of people are touched by the personal and societal impacts of these events.Courts of inquiry of mining disasters have often concluded that the disaster situation was ever present and could have been detected with diligent search. In addition human error has been identified as one of the most frequent immediate causes for the precipitation of the disaster. For the most part, then, mining disasters are caused by man."

Dec 1, 1996

By G. St. J. Perrott, N. A. Tolch

"PURPOSE OF TESTSThe propulsive strength4 developed by the Cardox blasting device depends on the thickness of disk, weight of heater element, and weight of carbon dioxide charge. It might be supposed that the maximum weight of carbon dioxide that can be charged into the shell should give the greatest strength. However, according to the ballistic pendulum, the maximum weight of carbon dioxide with certain conditions of heater and disk has less propulsive strength than a smaller charge; in one condition of test a loss of 39 per cent in propulsive strength was noted. It is therefore of interest to study the effect of the variables that determine the strength of Cardox.ACKNOWLEDGMENTGrateful acknowledgment is made to A. B. Coates, associate mechanical engineer who developed the testing method for measuring pressures in the Cardox shell.DESCRIPTION OF DEVICEThe Cardox blasting device as fully described by the bureau in Report of Investiga¬tions 2920 (1929), consists essentially of hollow—steel shell, cylindrical in shape, an electrode, valve assembly, shearing disk, and discharge cap. The shell is prepared for use by inserting a heater element, closing the open end with a shearing disk, and screwing in place the discharge cap. The charge of carbon dioxide enters the shell through the electrode.The heater element is fired by an electric igniter of the match—head type. The heat released by the heater element completely gasifies the carbon dioxide and raises the pressure of the gas until it is enough to shear the disk."

Apr 1, 1931

By Frank E. Cash

Accident prevention is an integral part of the operating procedure of the petroleum industry, and refinery officials and employees throughout the United States are exerting concerted effort to reduce the frequency and severity of accidents and are realizing definite results. In other words, the petroleum industry is safety conscious to a much creator decree than most of the other mineral industries. On January l, 1936, there were 11 operating, refineries in Louisiana with a crude-oil capacity of 199,750 barrels per day.4/ This report deals with safety in four of these refineries representing. 72 percent of the refinery capacity of Louisiana.

Jan 1, 1940

By J. W. Stevenson

The Bureau of Mines investigated the influence that atmospheric pressure changes exert in a gassy coal mil on a ventilating air current with a system of bleeder entries. During the season when abnormal barometric fluctuations usually occur, recording instruments monitored the air current ventilating an active coal-producing area. It HL he rate of coal production caused a more significant change in methane concentration than did barometric change. The hazard that accompanies methane release due to expansion of the gob gases during atmospheric lows was minimized by the effective bleeder system.

Jan 1, 1966

By M. I. Copeland

The investigation of the zirconium-gadolinium equilibrium diagram was part of a program to investigate rare:earth alloys for use as nuclear reactor control materials. Investigation of the zirconium-gadolinium equilibrium diagram revealed a eutectic system with limited terminal solubilities and one peritectoid reaction. The eutectic composition occurs at about 82 percent gadolinium, and the eutectic isotherm, which occurs at 1,220 ±5° C., extends from about 12 to 99+ percent gadolinium. A peritectoid isotherm occurs at 890 ±5° C. and extends from about 2 to 99+ percent gadolinium. The solubility of gadolinium in beta zirconium decreases from about 12 percent at 1,220 ±5° C. to about 2 percent at 890 ±5° C. The solubility of gadolinium in alpha zirconium decreases from approximately 5 percent at 890 ±5° C. to between 2 and 3 percent at 600° C. Vary little solubility of zirconium in gadolinium was indicated. An allotropic transformation of gadolinium was observed at 1,260 ±5° C. A change of the gadolinium transformation temperature on alloying with zirconium was not observed.

Jan 1, 1961

By Ronald T. Mayerle

There are no producing or developing mines in the Rattlesnake RARE II area. Specific areas with mineral occurences are prospects for: 1) stratabound copper and silver in Belt sedimentary rocks on the northwest border of the study area; 2) base metal sulfides, in thin veins and shear zones in Belt sedimentary rock, and diabase dikes and adjacent metasedimentary rocks in the southern part of the study area; 3) barite in sedimentary rocks near Rattlesnake Creek and Sheep Mountain; 4) limestone near Rattlesnake Creek and Blue Point; and 5) silica in quartz veins near the headwaters of Rattlesnake Creek and Sanders Lake. Stone, sand and gravel suitable for construction material are in the study area; however, equal or better quality deposits are common throughout the region. The RARE II area has no known oil and gas, coal, or geothermal energy deposits.

Jan 1, 1983

By F. S. LOTT, I. S. CULVER

The number of petroleum refineries in the United States decreased during 1948 from 390 to 375, continuing the trend to fewer units of larger individual capacity that has persisted since the peak in number of plants was recorded on January 1 , 1936. Large - scale construction of new processing facilities continued through 1948 with a resultant gain in daily crude-oil throughput capacity of installed equipment from 6,034,252 barrels on January 1 , 1948 to 6,438,995 barrels on January 1 , 1949. The capacity of the average refinery to process crude oil therefore increased during 1948 from 15,472 barrels daily to 17,171 . The principal areas of expansion of facilities were the strategic seaboard districts of the Texas and Louisiana Gulf Coast and the East Coast , and the important Indiana , Illinois , Kentucky, etc. , district that supplies markets in the upper Middle West region . These four districts accounted for 79 percent of the total new capacity added in the United States in 1948. The relatively small petroleum- refining industry of the Other Rocky Mountain district experienced a vigorous expansion in 1948 that will continue during 1949 . Capacity building on January 1, 1949 , amounting to 341,500 barrels daily, was 25,750 barrels lower than the comparable total on January 1 , 1948, but was the second highest on record . New construction was heavily concentrated in the Texas Gulf, East Coast , and Indiana -Illinois

Sep 1, 1949

By J. G. Kirby, F. S. LOTT

The mmber of petroleum refineries in the United States decreased during 1949 from 375 to 367 while the total crude-oil charging capacity of refineries continued to increase. A gain in the through-put capacity of 257,305 barrels daily raised the total to a new high level 6,696,300 as of January 1, 1950. The capacity of the average refinery to process crude-oil increased during 1949 from 17,171 barrels daily to 18,246. The four coastal refinery districts accounted for 178,900 barrels or 70 percent of the total capacity increase and the Illinois-Indiana- Kentucky district 57,950 barrels, or 23 percent. Slight declines in capacity were reported in the Texas Inland and the Arkansas-Louisiana Inland districts. The capacity building on January 1, 1950, 145,600 barrels daily, was less than half the amount under construction a year earlier. Most of the new construction involved enlargement of existing refineries and was confined to the East Coast and Indiana-Illinois-Kentucky districts. Two new refineries, however, were under construction, one in Oklahoma and the other in Texas. The shut-down capacity increased for the first time since 1946, and the 473,302 barrels daily reported on January 1, 1950, was the largest recorded since January 1, 1938. The only refining district showing a decline in the shut-down capacity was the Appalachian No. 2 district. The largest increases were reported in the Texas Gulf, Indiana-Illinois- Kentucky, California, and East Coast districts. The operating ratio of the petroleum refining industry, as indicated by dividing the January 1950 runs to stills of 5,483,000 barrels daily by the total installed capacity January 1, 1950, was 81.9 percent, compared with a ratio of 87.8 percent at the beginning of 1949.

Aug 1, 1950

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By Bruce D. Hanson

The Bureau of Mines conducted a series of experiments using four different coal types to determine the effect of attack angle and symmetric bit wear on airborne respirable dust (ARD) generated by point-attack bits and in energy consumption. Neither had a significant effect on ARD at the 95-pct confidence level, but bit wear had a significant effect (95 pct confidence) on specific energy (energy per gram of cut coal) for three coal types, Depth of cut was the most significant factor affecting ARD and specific energy.

Jan 1, 1979

By S. M. Shelton, F. D. DeVaney, M. M. Fine

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced ; although it is well -known that there are large deposits of low - grade ore in the United States , the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to obtain adequate supplies from foreign sources . Consequently, a program of laboratory and pilot - plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines . This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program . The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series , Report of Investigations 3606 , Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent , and C. H. Schack . Other reports will be published as the work progresses .

Feb 1, 1942

By George H. Holmes

This paper , which describes mining methods and milling and manufacturing operations at the gypsum property of the Blue Diamond Corp. , is one of a series on mining methods and practices being prepared by the Mining Division of the Bureau of Mines . The property comprises about 4,000 acres and is in secs . 30 , 31 , 32 , and 33 , T. 21 S. , R. 59 E. , and secs . 5 , 6, 7 , 8 , and 9 , T. 22 S. , R. 59 E. , M. D. B. and M. , Clark County , Nev . , approximately 23 miles by paved highway southwest of Las Vegas , Nev . ( fig . 1 ) . This circular summarizes the history of company operations , describes physical features , labor and living conditions , and the geology . The method of exploration is outlined , and the section on mining methods contains descriptions of open - pit and underground systems , including loading and transportation methods . The crushing plant and tramway are described , as well as plaster-mill and board -plant practices . The boiler plant and organization are described , and wage scales are contained in the concluding section of the circular .

Mar 1, 1950

By M. M. Fine

This report presents the results of laboratory mineral-dressing investigations by the Bureau of Mines of 14 individual or composite character samples from deposits in the Batesville manganese district. It will be noted that some concentrates have met or approached analytical specifications for metallurgical manganese ore although great variations in both physical and chemical composition from once deposit to another make each a new problem. In most cases it is evident that a substantial loss of manganese has occurred in the various slime and tailing products. An important aspect of this work is the research being conducted on manganese-bearing limestones. Recent reconnaissance indicates that this resource constitutes one of the major domestic reserves of manganese. Laboratory study has shown that ferrograde concentrates can be recovered from samples of manganese-bearing limestones from two properties. Research on samples from other areas is still underway.

Jan 1, 1957

By Edward D. Thimons

As U.S. mines go to greater depths, the high temperatures and humidities characteristic of such depths make it difficult to maintain a comfortable environment in working areas. Better techniques for cooling these deep working areas are needed. At the Homestake gold mine in South Dakota the Bureau of Mines has tested a water spray cooler inserted into the fresh air vent tube entering a warm stope. The cooler supplied more than 6 tons of refrigeration to the stope air, which dropped from an inlet temperature of 83° F dry bulb and 75° F wet bulb to 73.5° F dry bulb and 71.5° F wet bulb. These preliminary results show the water spray cooler to be a feasible concept. However, there is a need for substantial refinement and further testing, and work on the concept will be continued under contract to the Bureau.

Jan 1, 1979