Search Documents

By Paul Biggs

This Bureau of Mines report contains information on 63 water flood projects in Colorado. Water was injected in 10 formations located in 58 oilfields. Specific field data presented include location, discovery, development, water supply, fluid injection, oil and water production, oil reserves, and oil recoveries by primary and secondary methods. An estimated 3.5 billion barrels of water has been injected to recover approximately 533 million barrels of oil, a ratio of 6.57 to 1. Most of the injection water is from alluvial deposits, although produced water is used in many fields. Injection water treatment is not a major problem. Appraisal of project success or failure in this report is based on technical, rather than economic, information.

Jan 1, 1974

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By A. J. Kraemer

[The Bureau of Minas for a number of years has been studying the properties of crude petroleum from producing fields in the United States and Western Hemisphere and has published a series of reports on these fields, including oil fields of Texas.5]

Jan 1, 1927

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By Joseph W. Martin

The Bureau of Mines investigated the backscattering of low-energy gamma rays as a method for rapidly determining the incombustible content of coal mine dust. In this method, 60-kev gamma rays from americium-24l penetrate the dust and are reflected by elements in the dust to a thin crystal scintillation detector. The number of backscattered gamma rays is proportional to the incombustible content. Tests of 40 dry, mine-dust samples containing 50 to 100 percent inert material show an average error of 2 percent. Calibration of the apparatus is necessary for each rock dust to account for variable composition. Results for samples containing more than 6 percent moisture are subject to error, but the values are lower than values obtained by chemical analysis, and thus fall on the safe side. Development of a small portable meter based on the backscatter principle appears feasible. Such a meter would find application within coal mines to check the effectiveness of rock dusting procedures.

Jan 1, 1968

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993

By Donald P. Blasko

The Bureau of Mines investigated two areas of oil and gas seeps in the north-central Gulf of Alaska--Katalla River to Bering River and Cape Yakataga to Yakutat Bay to determine (1) whether previously reported seeps are still active, (2) the characteristics of the seeping hydrocarbons, and (3) the amount of bitumen contained in the drainage leaving the seeps and entering the Gulf of Alaska. Thirteen separate oil seeps, six bitumen deposits, and eight gas seeps were located, sampled, and analyzed. The oils ranged from 35.2° to 14.1° API gravity and had sulfur contents from 0.53 to 1.31 wt-pct. Bitumen samples had API gravities from 2.4° to 14.6° and sulfur contents from 0.28 to 0.88 wt-pct. Gas samples had specific gravities ranging from 0.577 to 0.883 and caloric values from 724 to 1,427 Btu/cu ft. A total of 63 water samples obtained from seep locations and seep drainages were analyzed by atomic absorption spectrophotometry for ionic content and by solvent extraction for hydrocarbon content. Although some of the water at the oil seeps had a bitumen content as high as 246,000 mg/1, the amount of hydrocarbons actually reaching the Gulf of Alaska averaged <0.2 mg/1.

Jan 1, 1976

By I. D. Shah

The copper-nickel ore of the Duluth Gabbro Complex in northeastern Minnesota is a large potential domestic resource of cobalt and platinum-group metals. However, because of the low grade of the primary metal values (0.5 pct Cu, 0.15 pct Ni), the private sector has assigned a relatively low priority to the development of technology for processing this ore, anticipating that mining probably would not begin until the mid-1990&apos;s. Furthermore, preliminary processing flowsheets considered by the mining companies centered on the primary metal values. As part of an effort to help provide the basis for technology to recover critical and strategic minerals from domestic resources the Bureau of Mines is investigating methods to recover all of the mineral values, in the Duluth Gabbro material, with particular attention to the byproduct critical minerals. A key step in this process is the removal of a relatively large amount of iron present in the bulk sulfide flotation concentrate to permit subsequent extraction of mineral values. This report describes a direct smelting method that removes most of the iron and produces a copper-nickel-cobalt matte, an intermediate product from which the metal values subsequently are separated. Copper, nickel, and cobalt grade and recovery data are presented for the direct smelting method. Test results showed that under certain conditions some of the mineral values reported to the slag, requiring slag cleaning to recover them.

Jan 1, 1983

By D. A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. H0122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available.

By Stephen D. Cramer

The solubility of methane, carbon dioxide, and oxygen was measured in brines at temperatures from 0° to 300° as part of Federal Bureau of Mines research on the corrosion of metals in high-temperature geothermal and mineral processing environments. Solubilities were measured by the technique of extracting pure gas, dissolved at pressures where Henry&apos;s law was applicable, from known volumes of brine. The results were smoothed with respect to temperature. The solubility, expressed in terms of the Henry&apos;s law constant, reaches a maximum at temperatures ranging from 60° to 100° C for methane and oxygen, and from 160° to 170° C for carbon dioxide. The Henry&apos;s law constant increases, that is, gases are salted out of the brines, in the presence of dissolved salts. Salting-out coefficients are strongly dependent upon temperature. The temperature dependence of the Henry&apos;s law constant for geothermal brines is different from that for sodium chloride brines owing to the more complex chemistry of the geothermal brines. The solubility of oxygen and carbon dioxide in brines exposed to air saturated with water vapor and at a total pressure of 760 mm Hg is reported for temperatures from 0° C to the normal boiling point.

Jan 1, 1982

By Steven R. Davis

Dear Interested Party: Subject: Notice of Intent to Solicit Outside Opinions Regarding Amendments to the Rules Concerning the Leasing of State Owned Lands for the Mining of Metallic Minerals The Department of Natural Resources, Division of Minerals, is seeking outside opinions concerning the leasing of state owned lands far the mining of metallic minerals. Enclosed for your information in a copy of the Notice of Intent to Solicit Outside Opinions Regarding Amendments to the Rules Concerning the Leasing of State Owned Lands for the Mining of Metallic Minerals.

Jan 1, 1994

By A. J. Kraemer

The Bureau of Mines for a number of years has been carrying on an investigation of properties of crude oils from producing fields in the United States and has published a series of reports on different fields, including oil fields of Texas3. Production Data The Spindletop field was discovered in 1901 when the pay sand was found at deaths of about 800 feet. During the following twenty-five years a number of attempts were made to find a deep productive sand. All attempts sere failures until a roll drilled by the Yount Lee Oil Company found oil late in 1925. An intensive drilling campaign began at once, and the production of the Spindletop field increased to a daily average of 93,217 barrels in September, 1926; the present production is estimated at 66,000 barrels doily. Tile following table taken from the Oil and Gas Journal for February 10, 1927, shows the daily average and the total production by ninths for 1926.

Jan 1, 1927

By McHenry Mosier

Mercury is one of the strategic metals the supply of which has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributes substantially to increased production of mercury in the United States and to consequent accumulation of Governments stock. Other contributing factors were higher prices for mercury and Government loans to operators. The Bureau has undertaken 15 exploration projects, 13 of which have been completed. This work comprised 40,307 feet of drilling arid 35,082 linear feet of sure ace trenching and has indicated commercial ore containing 37,400 flasks of mercury and marginal ore contain¬ing 29,200 flasks - a total of 66,600 flask , equivalent, respectively, to domestic production at 50,000 flasks per year for 9 months , 7 months, and 16 months. Early in 1944, as Government stocks had become adequate, domestic production was gradually curtailed cancellation of Government contracts for the purchase of mercury and Government control of labor and operating supplies.

Jan 1, 1944

By R. M. Ray

The Bureau of Mines evaluated five commercial badge-type carbon monoxide dosimeters. Color changes in the badge reagent indicated the presence of carbon, monoxide. Possible effects of ambient conditions on dosimeter response to CO during or after coal mine fires or explosions were studied. Temperature and humidity changes did not change dosimeter sensitivity to CO. Contaminant gases such as CO2, N02, S02, and H2S had effects that varied with brands of dosimeters ranging from no effect to increased sensitivity to CO. Dosimeters tested after 6 months of storage showed an increase in failure rate as high as 25 percent. Tests were conducted to determine the effects on dosimeter time-for-color change caused by observer&apos;s sight (colorblind); lighting, and coal dust on dosimeters. No significant effects were observed. Observer variance was the most pronounced factor observed in all tests.

Jan 1, 1975

By J. T. Popp, C. M. McCulloch

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con- tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

By Sumner M. Anderson

THE ENORMOUS contrast between the mineral economy of Cuba in 1963 and in 1958 was the result of the overall Political changed to which the total economy of the country was intimately lined. Creation of the Cuban Mining Institute (Instituto Cubano de la Minería) to direct all mining activities in the country was an early act of the new Government after the revolution on January 1, 1959. During the next 2 years, the Government confiscated foreign holdings,2 including Unite States investments exceeding $1 billion in value. Foreign mining and metallurgical technicians-predominately from Communist areas-were brought in to reorganize the mineral industries. On January 3, 1961, diplomatic relations between Cuba and the United States were severe and then on May 2, Cuba announced its full-fledged membership in the so-called Communist Bloc. Fifty-four international treaties assured Cuba of Communist economic support, technical and financial assistance, machinery, raw materials, and manufactures. The Soviet Union agreed to buy some Cuban mineral products, and Czechoslovakia stated that it would buy all mineral production offered for the next 20 years, but in both cases at prices said to be much lower than the world market. The mineral productivity segment of the mineral economy during and since the period of political metamorphosis, has withstood the political disruption better than has the economy as a whole, but with no direct measure of the magnitude of its cost. The overall economic record is marked with steady deterioration; the annual average per capita income has dropped from $374 in 1957 to $185 in 1963, when Cuba&apos;s deficit with the Soviet Union alone reached an admitted $1 billion.

Jan 1, 1964

By S. J. Schatzel, J. Cervik, A. A. Campoli

The cross-measure borehole technique is being studied by the Bureau of Mines as an alternative to the use of surface gob boreholes as a means of controlling methane in gobs during longwall mining. Small-diameter holes are drilled from underground locations into strata overlying the mined coalbed. When the roof strata are fractured by the mining opera- tion, a partial vacuum applied to the boreholes draws the methane out of the fractured strata and prevents it from entering the mine ventilation system. Tests in the Upper Kittanning Coalbed showed that 50 pct of the methane produced by the longwall mining operation was captured by the cross-measure boreholes. Borehole inclination and penetration into the gob are two important borehole parameters that affect the performance of the cross-measure borehole system.

Jan 1, 1983

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the personnel of many mines are observing to prevent similar occurrences, The Bureau has conducted extensive research on roof-control problems, but a comprehensive study of fatal roof-fall accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal-mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May 1941, Public Law 49, and reports covering the investigations are distributed to management, the State mine inspection agency, and representatives of the mine workers organization having jurisdiction at the mine. SCOPE AND PURPOSE OF STUDY This study covers the Federal investigation of 263 of the 315 fatalities from falls of roof, face, or rib that were charged to the bituminous-coal industry during the calender year 1950. The number of roof-fall fatalities investigated is recorded by States in table 1.

Jan 1, 1951

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals and investigations of their chemical and physical properties. The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures When placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld. County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937