Search Documents

By K. J. Miller

A two-stage froth flotation technique was developed in the laboratory to separate fine-size pyrite from coal. The process consists of the initial flotation of a 15-percent solids coal slurry with a minimum of frother; the coarse, free pyrite and other refuse are removed in the tailings. The froth product from this first stage is then repulped and treated with a coal depressant, a pyrite promoter, and a frother to float the remaining fine-size pyrite or pyrite attached to coal particles. With the two-stage process, the pyritic sulfur content of a Lower Freeport bed coal sample was reduced from 1.78 percent to 0.75 percent in the first stage, and from 0.75 percent to 0.27 percent in the second stage with good clean coal recovery.

Jan 1, 1972

By Edward L. Burwell

The Bureau of Mines investigated the use of dilute polymer in brine solutions to increase the efficiency of air in gas flooding model oil reservoirs. Slugs (0.23 pore volume) of 500 ppm polyacrylamide were injected into a model, consisting of a high- and a low-permeability core, that had been previously gas flooded to residual oil. Gas flooding was then resumed. Of the total gas volume injected, the percentage entering the high-permeability zone was greatly reduced after polymer injection but remained unchanged when slugs of water without polymer were used.

Jan 1, 1970

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

By L. B. Pankratzt

The heat content above 298.15° K of ferroelectric lithium columbate (LiCbO3) was measured to 1,770° K. The Curie temperature was determined to be 1,450° K, the melting point 1,540° K, and the heat of fusion 16.94 kcal/mole. Heat content and entropy increments have been tabulated for the temperature range from i98.15° to 1,800° K. Heat contents are also given in equation form.

Jan 1, 1966

By Claire C. Caruso, John M. Russo, Jennifer M. Schmit, Robert B. Dick, Edward M. Hitchcock

PURPOSE This report provides an integrative review of 52 recently published research reports that examine the associations between long working hours and illnesses, injuries, health behaviors, and performance. The report is restricted to a description of the findings and methods and is not intended as an exhaustive discussion of all important issues related to long working hours. Findings and methods are summarized as reported by the original authors, and the study methods are not critically evaluated for quality. SUMMARY In 16 of 22 studies addressing general health effects, overtime was associated with poorer perceived general health, increased injury rates, more illnesses, or increased mortality. One meta-analysis of long work hours suggested a possible weak relationship with preterm birth. Overtime was associated with unhealthy weight gain in two studies, increased alcohol use in two of three studies, increased smoking in one of two studies, and poorer neuropsychological test performance in one study. Some reports did not support this trend, finding no relationship between long work hours and leisure-time physical activity (two of three studies) and no relationship with drug abuse (one study). A pattern of deteriorating performance on psycho physiological tests as well as injuries while working long hours was observed across study findings, particularly with very long shifts and when 12-hour shifts combined with more than 40 hours of work a week. Four studies that focused on effects during extended shifts reported that the9thto 12th hours of work were associated with feelings of decreased alertness and increased fatigue, lower cognitive function, declines in vigilance on task measures, and increased injuries. Two studies examining physicians who worked very long shifts reported deterioration on various measures of cognitive performance. When 12-hour shifts combined with other work-related demands, a pattern of more adverse findings was detected across studies. Six studies examining 12-hour shifts combined with more than 40 hours of work per week reported increases in health complaints, deterioration in performance, or slower pace of work. Two studies com-paring 8- and 12-hour schedules during day and night shifts reported that 12-hour night shifts were associated with more physical fatigue, smoking, or alcohol use. Two studies examining start times for 12-hour shifts reported that decrements in alertness or more health complaints were associated with early 6:00 a.m. start times. One study examining 12-hour shifts in hot work environments reported a slower pace of work as compared with shorter shifts. Another study examining high workloads during 12-hour shifts showed increased discomfort and deterioration in performance as compared with shorter shifts. More definitive statements about differences between 8-hour and 12-hour shifts are difficult because of the inconsistencies in the types of work schedules examined across studies. Work schedules differed by the time of day (i.e., day, evening, night), fixed versus rotating schedules, speed of rotation, direction of rotation, number of hours worked per week, number of consecutive days worked, number of rest days, and number of weekends off. All of these factors could have interacted with overtime and influenced study results. Also, some studies did not report how many hours participants worked per week or other details about the work shifts, which complicated the assessment of their results. The many

Jan 4, 2004

By M. H. Chetrick

An important factor in the design and operation of a lignite-gasification plant is knowledge of the thermal requirements. These not only vary with different-size plants but also with the operating conditions for a plant of given capacity. Thermal data have been collected since 1945 from a commercial-scale lignite-gasification pilot plant operated by the Bureau of Mines at Grand Forks, N. Dak. The description and operation of this plant and a study of the gas-composition data have already been described in previous reports (1, 2, 3, 4, 5).2) / This investigation was made to review the thermal data taken in tests and to correlate them in terms of the fraction of undecomposed steam and the H2:CO ratio.

Jan 1, 1953

By R. V. Ramani, R. Bhaskar

"The National Academy of Sciences (1) recognized the importance of studying the spatial and temporal characteristics of respirable coal mine dust atmospheres. In this paper, the progress to date of a research project on dust transportation and deposition in mine airways is presented. A mathematical model is proposed for studying the transport of dust. A source representative of dust generation in underground coal mining is defined. The influence and applicability of surface roughness, dispersivities, coagulation and reentrainment to vine dust flow arc examined. A convective-diffusion model is proposed for the transport and deposition of dust in mine airways. Using the model, the spatial and temporal characteristics can be evaluated in terms of dust concentrations in the mine atmospheres.INTRODUCTIONThe prediction of the behavior of fine particles Is Important in many fields of science and engi¬neering including physics, chemistry, mining, mineral processing, and atmospheric science. In mining from the health point of view, fine coal dust is associated with the appearance of pneumoconiosis in miners exposed to the dust. Also, in addition to being a nuisance factor obscuring visibility and general mobility of miners, it can lead to sudden catastrophic incidences of explosions. This paper outlines the progress to date of a research project on dust transportation and deposition in mine airways. A mathematical model is proposed for studying the transport of dust for the various mechanisms. The dust dispersion is defined in terms of a dispersion term determined from experimental data by Skubunov (23). Coagulation is considered as one of the mechanisms that can lead to changes in the particle size distribution. Reentrainment as a possible secondary source of dust was examined during model development but was not included in the final model."

Jan 1, 1988

By C. E. Armantrout, H. Kato, M. I. Copeland

The data collected during this investigation indicate that the chromiumgadolinium system has extensive liquid immiscibility and one eutectic point . Liquid immiscibility occurred at temperatures above the monotectic isotherm , 1,830 ° C , which extended from less than 0.25 to about 85 weight - percent gadolinium . The eutectic was at 96 percent gadolinium and 1,170 ° C. Gadolinium and chromium were the only phases in this system . There was a solid solubility of less than 0.25 percent gadolinium in chromium at 1,730 ° C and less than 0.10 percent chromium in gadolinium at 1,160 ° C. The alloys were prepared by nonconsumable - electrode arc - melting , and the alloy system was investigated by heat treatment , metallography , thermal analysis , and X- ray diffraction . All the melting , heat treatments , and thermal analyses were conducted in a vacuum or in helium because of the reactivity of chromium and gadolinium with the components present in the atmosphere at elevated temperatures .

Jan 1, 1964

By G. W. Weems

The Bureau of Mines combined preconcentrating techniques and mass spectrometry to develop a parts-per-billion general analysis of impurities in helium. The impurities are preconcentrated using a Bureau trace-impurity analyzer; 35-mm Hg pressure of helium is left in the concentration trap to sweep the impurities into the mass spectrometry and provide a 10-mm Hg sample pressure.

Jan 1, 1966

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

By H. W. Kilau

Thermodynamic calculations indicate that an electrochemical cell might serve as an analytical device for determining the composition of high-purity metals. An equation, readily derived, for the cell voltage, E, is as follows: [E I RT In F NFe unknown sample T of L NFe standard] The cell, however, must come to equilibrium, must be reversible, and must have no thermal effects or complicating side reactions whose magnitude is indeterminable. This Bureau of Mines investigation explores the feasibility of an electrochemical technique for the analysis of high-purity iron. Experiments were conducted using room-temperature aqueous cells and high-temperature molten salt cells. The room-temperature cells proved to be irreversible. The high-temperature cells utilizing FeCl2 and a eutectic mixture of KC1-LiCl were reversible, but did not attain a constant voltage necessary for analytical considerations.

Jan 1, 1963

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years ago were only laboratory curiosities.

Jan 1, 1941

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years a ago were only laboratory curiosities.

Jan 1, 1941

By Thomas O. Llewellyn

This U.S. Bureau of Mines (US8M) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material balance for the year 1989.

Jan 1, 1992

By N. F. LeJeune

[ ]

Jan 1, 1924

By Jr. Taylor

The following heats of solution have been measured in 1.160 molal H2SO4 at 25° C: AH298, kcal./mole Be(c) + 77.44(H2SO4?47.849 H2O) H2(g) + BeSO4 (soln) -92.83 ± 0.11 BeSO4 ?(c) + 77.44 (H2SO4?47.849 H2O) BeSO4(soln) -16.45 ± 0.02 BeSO4?2H2O(c) + 77.44(H2SO4?47.849 H2O) BeSO4?2H2O(soln) -5.395 ± 0.019 BeSO4?4H2O(c) + 77.44 (H2SO4?47.849 H2O) BeSO4?4H2O(soln) 1.513 ± 0.010 Combining these data with other experimental results and data taken from National Bureau of Standards information yielded the following heats of formation at 298° K:

Jan 1, 1966

By Ralph H. Whaite

The Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region is described. A catalog of the maps that have been microfilmed in the Eastern Middle anthracite field--the first area to be covered in the program--is presented. Additional catalogs will be published as significant mining areas are completed.

Dec 1, 1964

Objective: To provide a safe, practical, cost-effective method for measuring coal rib thickness during highwall mining.

Jul 1, 2008

[ ]

Jan 1, 2011

By Forest J. Sur

"This report describes an exploratory project conducted by the Bureau of Mines on a fluorite deposit near Vado, N. Mex. Results of trenching are given. Together with analyses made upon samples of the ore. The Federal Geological Survey3/ completed a preliminary geologic study and mapped the deposit during the summer of 1944. A Bureau engineer examined the deposit in August 1944. As a result of these investigations, it was concluded that the deposit contained substantial inferred ore reserves. Exploratory work was recommended to obtain information that might possibly lead to production from the property. Assistance was given the Bureau by the Geological Survey.A gasoline-powered air compressor, other equipment, and supplies were delivered to the property from January 20 to 25, 1943. Trenching began under the direction of a Bureau of Mines engineer on January 25, 1947, and ended on March 15, 1945. The results of trenching and sampling form he basis of this report.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. IT is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, R.G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervisions of Dr. R. S. Dean, assistant director."

Sep 1, 1946