Search Documents

By W. L. O'Brien, E. A. Rowe

Electrorefined vanadium with additions of up to 5 percent by weight of yttrium, cerium , lanthanum , praseodymium, neodymium, and samarium was melted to ingots in a nonconsumable electrode arc in a helium atmosphere . The ingots were rolled into strips and evaluated for the effect of the alloying elements on hardness , tensile strength , ductility , recrystallization temperature , and microstructure . Except for samarium , average additions of alloying elements of 1 to 2 weight - percent resulted in the retention of 0.12 to 1.05 weight - percent in the alloys and reduced the ultimate tensile strength from about 48,000 to approximately 30,600 psi . The corresponding yield stress (0.2 percent offset ) was reduced from about 40,700 to approximately 20 , 200 psi . Diamond pyramid hardness (DPH) was reduced from 117 to an average of 62 kg /mm² . Increased malleability at room temperature resulted with yttrium and all rare - earth- metal additions , except samarium , particularly with more than 0.25 weight - percent additions . Decreasing oxygen contents corresponded with the changes noted in the mechanical properties of the alloys . The recrystallization temperature of electrorefined vanadium was reduced from approximately 950 ° to 800 ° C. Yttrium or a rare- earth metal content , except samarium , in excess of 0.1 weight - percent in vanadium produced a second phase suggestive of an eutectic which indicated a possible maximum solubility of less than 0.1 weight - percent for both room and elevated temperatures .

Jan 1, 1964

By O. C. Blade, Elizabeth Hughes

Conservation in the utilization of any product is always subject to improvement if the composition and properties of the product are known. Petroleum is no exception, and knowledge of the characteristics of crude oils, even when given on the broad basis of routine type analyses has proved useful to chemists, engineers, and geologists in improving pro- duction and utilization of petroleum. For a quarter of a century the Bureau of Mines has sought to provide such information regarding crude oils and has analyzed many samples of petroleum by its standardized rou- tine method. Most of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published up to January 1, 1948. The routine method used for all these analyses is basically the same as that described by Dean, et al.. Briefly, the procedure consists of testing by standard methods, small samples of a crude oil for gravity, sulfur, color, and viscosity, and of distilling a sample of the crude oil by a standardized procedure and determining certain properties in the sep- arated fractions and residuum. Careful records are made during the proce- dure, and the distillation data obtained are used to calculate the approx- imate amounts of products present in the sample such as percents of gas- oline, kerosine, gas oil, and lubricants. The data obtained are recorded on a standard analytical report form. An analysis of a sample of typical midcontinent crude oil is shown in table 1. Compilation of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses are often shown in connection with other studies, such as engineering field reports. This bibliography is a compilation of references to 115 publications, which contain analyses of crude oils by the Bureau of Mines. References may be found to analyses of crude oils from the United States, Canada,

Jun 1, 1948

By F. R. Lee

This publication lists permissible equipment approved by the Bureau of Mines during 1965 and 1966 (calendar years), except for breathing apparatus and explosives. The purpose of this publication is to inform the public about approved equipment for safe use in underground mines.

Jan 1, 1968

By Jr. Sillers

This is the sixth report of investigations in cooperation with the steel industry to establish the technological acceptability of electrolytic manganese in steelmaking processes. The bulk of the .electrolytic manganese used in these tests was produced by the Bureau Of Mines from domestic ores at its Boulder City, Nev., pilot plant by the process developed by the Bureau. Electrolytic manganese for the first series of tests made in 1940 was supplied by the Electro manganese Corp., Knoxville, Tenn. The first report dealt with the application of electrolytic manganese to the manufacture of stainless.steel;9 the second with tests in acid electric and acid open-hearth low and medium carbon-steel castings; the third with its use in rimmed and? killed low-carbon steels; the fourth with its application to the manufacture of stainless steel as well as the Timken 16-25-6 alloy for gas turbines; and the fifth with tests in acid and basic electric steel foundry practice and basic steel ingot production.

Jan 1, 1948

By Boyd Guthrie

The current use of Mid - Continent crude oil for the manufacture of war products , such as aviation gasoline and lubricating cil , has caused an acute shortage of available supply from established sources . Therefore , refiners who heretofore have had no reason to use West Texas crude oils now are considering them as charging stock and need more information concerning their characteristics . The Bureau of Mines has published several reports3/ giving analyses of the most important of these crude oils . However, to make the applicable data in these publications readily available to refiners , the present compilation of analyses of West Texas crude oils has been prepared . Data showing the effect of catalytic desulfurization of naphthas from West Texas crude oils have been presented in a restricted Bureau of Mines Report of Investigations . These analyses were made under the general supervision of R. A. Cattell , chief, Petroleum and Natural Gas Division, Bureau of Mines , Washington, D. C. , and N. A. C. Smith, supervising engineer , Fetroleum Experiment Station, Bureau of Mines , Bartlesville, Okla . , and under the direct supervision of Harold M. Smith, senior petroleum chemist, Bartlesville , Okla .

Jan 1, 1944

By Stephen D. Cramer

The objective of the present studies was to develop thick adherent and coherent coatings of platinum and palladium on refractory metals and other substrates of industrial and engineering importance. Existing platinum and palladium electrolytes were modified to make them suitable for the electrodeposition of thick deposits. The optimum operating conditions for these electrolytes were established. Pretreatment procedures for columbium, copper, graphite, molybdenum, nickel, stainless steel, tantalum, titanium, tungsten, vanadium, and zirconium substrates were studied. New pretreatment procedures for columbium, molybdenum, stainless steel, tantalum, tungsten, and nickel were developed. The internal stress and hardness of selected electrodeposits were measured. The effects of heat treatment upon the properties of electrodeposits were studied.

Jan 1, 1967

By Robert H. Bedford

The New Almaden mine was discovered in 1824, and since that date production of quicksilver has exceeded 1,000,000 flasks. Because of this high production record, the New Almaden area was, upon passage. by Congress of the Strategic Minerals Act of 1939, immediately considered by the Bureau of Mines as a promising location for exploration. In 1941, the Federal Geological Survey undertook a survey of the entire district. R. R. Trengove, an engineer of the Bureau of Mines, made a preliminary study for a project in 1942, and in August 1943 the Bureau, in close cooperation with the U. S. Geological Survey, began the development project described herein. The Bureau of Mines drilled 36 holes, totaling 6,807 feet of diamond drilling, along the contact between the serpentine and Franciscan, sandstones and other sedimentary formations. The ore bodies are found along this contact and occur in the carbonate-silica rock. This report briefly describes the location, history, and ore deposits of the property. The recent operations are outlined, and the work performed by the Bureau is explained in detail.

Jan 1, 1950

By Nunna Malakondaiah

Plant samples collected from the mined sites of Beulah, Center and Zap and the test sites of North Beulah 1, North Beulah If, South Beulahh and Center were analyzed for their nutrient concentrations. The vegetation from the mined areas generally showed lower concentrations of Na, P and Cu and failed to meet the nutritional requirements for beef cattle as defined by National Research Council (minimum requirements are: Na, 600; Cu, 4; P, 1800 µg/g dry weight). Plants from Beulah showed generally higher concentrations than from Center or Tap. Tissue concentrations of K varied significantly between sites for 5 species due to the low tissue concentrations at Center. Deficiencies are difficult to isolate as the sampling was done in mid-summer and generally during that season the tissue concentrations tend to decrease in several species. All of the plant species at the unmined sites, with the exception of western wheatgrass at Zap, had lower concentrations of P than the minimum nutritional requirements for beef cattle. Sodium concentration was low but Cu was marginal to adequate in plant species at the unmined sites. Concentrations of K, Mn and Cu in western wheatgrass were greater at Center than at Zap while the opposite was true of the concentrations of Zn, Cu and P in blue grama and Cu in green needlegrass. Amending the spoil with slack at North Beulah I decreased the concentrations of Zn, Cu and P in wheatgrasses grown on spoil from 0-2, 5-10, and 20-25 foot depths, respectively. In general, the mean tissue K+/Na+ ratios were greater in plants on slack amended spoils, primarily due to the reduced Na concentrations in the tissue. At North Beulah II test site, only wheatgrasses grown on spoil amended with slack showed significant increase in K and decrease in Na and Mn concentrations. At South Beulah test site which received 12" topsoil over graded spoil, leonardite amendment decreased P concentrations in all of the grasses as compared to control, whereas fertilizer treatment increased the same. Nutrient concentrations were lower in both fescue and needlegrass with leonardite treatment and higher with fertilizer treatment although not significantly different from control. The concentrations of Ca, Mg, Na, Fe, Cu and N in grasses grown on topsoil at Center test site were significantly higher than on slack amended spoil. Legumes grown on topsoil at Center site contained higher concentrations of P than those grown on spoil; there were no significant effects due to slack on spoil or topsoil. The data presented in this report act only as an indication of between-treatment and between-species differences in tissue composition of plants harvested in mid-summer season. With respect to the nutrients analyzed, since none were found to be toxic, the cattle can safely feed on the vegetation of these mined areas.

Jan 1, 1982

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966

By R. V. Lundquist

The compound 2Na2O?3CaO?5Al2O3 occurs as a minor phase in lime-soda sinters prepared for extracting aluminum from siliceous aluminum-bearing materials. About 99 percent extraction of sodium and aluminum from synthesized 2Na2O.3CaO.5Al2O3 was obtained in solutions of NaOH-Na2CO3 at leaching temperatures of 50° C and above. Extractions in water were low because insufficient NaOH was generated by hydrolysis. Extractions in NaOH solutions were limited to about 80 percent owing to the precipitation of hydrated calcium aluminates. Rapid extractions of 100 percent were obtainable in NaaC03 solutions, but the subsequent rapid precipitation of alumina trihydrate caused losses in alumina recovery.

Jan 1, 1965

By L. K. Weaver

The objective of this Bureau of Mines publication Is to present a nomograph that provides a fast, convenient method for estimating hydrocarbon lease bonus bids for offshore acreage in the Gulf of Mexico. Discounted cash flow analyses were computed from a model derived to show the costs necessary to explore, acquire, develop, produce, and abandon a 5,000-acre block of offshore acreage, and the estimated income from the sale of the hydrocarbons produced from the block. The range of the variables in the financial analyses used to construct the nomograph are prices of oil, $2.50 to $5.00; recoverable hydrocarbon reserves, 44,651,476 to 127,575,645 barrels; and discounted cash flow (DCF) rates of return, 5.0 to 57.2 percent. A total of 1,234 sets of DCF data were used to construct the nomograph. The range of bonus bids shown on the nomograph is from 2 to 90 million dollars ($400 to $18,000 per acre).

Jan 1, 1973

By A. J. Kraemer

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the on the districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of eight. California crudes. Analyses of other crude oils from California have been published it Reports of Investigations 2595, 2608, and 2846. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting 65 samples was facilitated by the courtesy of representatives of oil companies in California. The methods used in testing and analyzing the samples are described in detail in Bureau of Mines Bulletin 207. A discussion of the interpretation of crude-oil analyses, as made by the Bureau of Mines, is given in Bureau of Mines Report of Investigations 2806.

Jan 1, 1931

This paper on. the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States., The paper includes a short discussion of results, tabular data, and individual analyses of eight California crudes. Analyses of other crude oils from California have been published in Reports, of Investigations 2595,3/ 2608,4/ and 28465/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting samples was facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1931

By Walter R. Storms, Allan B. Bowman

This paper , which describes mining methods and practices at the Mineral Hill copper mine , is one of a series being prepared by the Division of Minerals of the Bureau of Mines on mining methods , practices , and costs in various mining districts. of the United States . The Mineral Hill mine is situated on the northeastern piedmont of the Sierrita Mountains at an altitude of 3,650 feet in sec . 35 , T. 16 S. , R. 12 E. , and sec . 2 , T. 17 S. , R. 12 E. , Pima mining district , Pima County , Ariz . ( fig . 1 ) . The claims (figs . 2 and 3) are in a gently rolling area with only scant desert vegetation . The average annual precipitation is about 11 inches . The nearest surface water is the Santa Cruz River , an intermittent stream 8 miles east of the mine . The property is owned by the Banner Mining Co. , a Nevada corporation . This report presents a brief history of the mine , describes the geology of the area and the ore deposits , outlines methods of prospecting and exploration , and gives methods of sampling and the estimation of ore reserves and values . Development and stoping methods are explained , and methods of underground transportation , ventilation , mine drainage , and safety measures are described . The concluding section of the paper is a section on milling . The Mineral Hill mine is an old mine that was reopened in 1951 after having been closed for 30 years .

May 1, 1957

By Albert W. Deurbrouck

Twelve samples from six Barbour County coal beds were analyzed for this report. The samples collected were generally high sulfur content coals, frequently exceeding 3 percent in the raw-coal sample. Many of them could not be upgraded to acceptable metallurgical standards even by rigorous preparation procedures. The production of coal in the county in 1963 amounted to almost 3 million tons of which 44 percent was mechanically cleaned.

Jan 1, 1965

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 318 petroleum refineries in the United States with a total daily crude throughput capacity of 8,632,390 barrels as of January 1, 1956. Compared with the previous year the total number of refineries declined 8 while the crude throughput capacity increased 211,760 barrels daily. Three refinery districts accounted for 90 percent of the crude-oil capacity increase, the California district 34 percent; the Texas Gulf Coast district, 31 percent; and the Indiana-Illinois-Kentucky district, 25 percent. Decreases in capacity during the year were reported for the East Coast, Appalachian #1, and the Arkansas-Louisiana Inland districts. The capacity of the average refinery to process crude oil increased during 1955 from 25.830 barrels daily to 27,145.

Jan 1, 1956

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 12,564-acre portion of the 34,795-acre Rockhouse Wilderness Study Area (CA-010-029) in order to evaluate its identified mineral resources. The study area is located in Kern and Tulare Counties, CA, about 60 air mi northeast of Bakersfield at the south end of the Sierra Nevada. A review of the geologic and mining literature, and a field examination identified a turquoise and a gold prospect in the study area, and another gold prospect and a feldspar prospect within a mile of the study area boundary. Thirty-three rock and 16 alluvial samples were taken.

Jan 1, 1988

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966

By Almon F. Robertson

The floor of Shady Valley, Johnson County, Tenn., is underlain by the Shady dolomite formation. In places the residual clay derived from this formation contains considerable manganese oxides. Nine properties in Shady Valley and two in Doe Valley were prospected by the Bureau of Mines from January 1943 to April 1943. The results obtained indicate that the ore bodies are small and spotty and, that the ore is not well-adapted to gravity concentration. The work of the Bureau was confined to the open end of the valley. One mile northeast of the Ham Greer property, Beaverdam Creek enters a rocky gorge, and it was believed that the few prospects in this area were of secondary impor-tance and, owing to the steep slope and general roughness of the terrain, that exploration with the rite', bucket-drill would be impracticable. A total of 4,398.5 feet was drilled in 131 holes. In addition, 235 lineal feet of bulldozer trenches were cut and 4.5 feet of test pits were sunk. The following nine properties were explored in Shady Valley: Bentley, Walker, Blevins, Scott, North Ham Greer, South Ham Greer, Lipford, Blackburn, and Steagall In Doe Valley, the Gerd Shoun and Brookshire properties were explored.

Jan 1, 1949

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979