Search Documents

By Maurice Deul, Herbert H. Fields, John H. Perry

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (2), and pipeline--quality gas was introduced into a commercial pipeline. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed.

Jan 1, 1975

The National Institute for Occupational Safety and Health (NIOSH) National Personal Protec-tive Technology Laboratory (NPPTL) and the Mine Safety and Health Administration (MSHA) conduct a Long Term Field Evaluation (LTFE) program to evaluate deployed self-contained self-rescuers (SCSRs). The objective of the program is to evaluate how well SCSRs endure the under-ground coal mining environment with regard to both physical damage and aging when they are deployed in accordance with Federal regulations (30 CFR 75.1714). This report presents ?ndings of the combined eighth and ninth phases of the LTFE. For these phases, over four hundred SCSRs were evaluated. The units tested include the CSE SR-100, Draeger Oxy K-Plus, MSA Life-saver 60, and the OCENCO EBA 6.5. The OCENCO M-20 was evaluated only in Phase 9. Testing was per-formed between December 2000 and April 2004. Results of the evaluation indicate that all SCSRs experience some performance degradation due to the mining environment. Observed degrada-tion varies from elevated levels of carbon dioxide, high breathing resistance, and reduced capacity. Mechanical degradation to the SCSR components included breathing hoses, chemical beds, outer cases and seals. The LTFE tests discussed in this report are different from tests performed for SCSR certi?cation to the requirements of 42 Code of Federal Regulations, Part 84 (42 CFR, Part 84). LTFE tests reported here are conducted to an end point, oxygen depletion, to enable comparison of the duration of new and deployed SCSRs. The method for obtaining deployed SCSRs for this evalua-tion was not a random selection from the deployed population of SCSRs. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the generalizability of the results. This program will be implemented following completion of Phase 10 of the current LTFE protocol.

Jan 10, 2006

By John A. Organiscak

Laboratory and underground studies were conducted by the Bureau of Mines to evaluate the effectiveness of a water-powered scrubber and a brattice partition to create a clean split of air for longwall workers at the tailgate. In simulated laboratory tests, the system was very effective in creating a clean split of air. Observed system efficiencies were 74 and 84 pct with induced airflows of approximately 2,000 and 2,500 cfm, respectively. Underground evaluations indicated that the system was capable of reducing respirable dust at the tailgate. The first underground evaluation resulted in protection efficiencies of 30.7 and 42.5 pct at scrubber water pressures of 150 and 450 psig, respectively. A 33.7-pct protection efficiency was observed in the second underground evaluation with a modified partition and the scrubber operating at 250-psig water pressure. To be most effective, the system should have the scrubber operating at a flowrate of 10 gpm at 500 psig to deliver a maximum quantity of cleaned air behind a well-sealed partition.

Jan 1, 1983

By Robert L. Thorne

As an integral part of the investigation of critical and essential minerals in Alaska , the Bureau of Mines examined the lead deposits in the Slana area . Four examinations were made during June , July, and August 1945 in the 200 - square -mile area immediately northwest of Slana . The settlement of Slana lies near the conflux of the small Slana River with the mighty Copper River less than 60 miles southwest of Tek Junction on the Alaska Highway . Travel through the area and the examination of the properties were conducted by a three-man crew consisting of the author , a caterpillar operator , and a laborer . An RD6 caterpillar , equipped with blade and winch , was used in breaking trail and freighting through the country . Supplies and equipment were loaded on a 7- by 14 -foot , double - end , go -devil , which was hauled by the tractor .

Nov 1, 1946

To provide accurate navigation and control of continuous mining systems.

Jan 1, 1996

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant's electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By John Millhiser, Stephen J. Kravits

The U.S. Bureau of Mines preproduction Wireless Survey System (WSS) and its performance during an in-mine test are discussed in this report. The WSS was developed to reduce downhole surveying time in order to increase the efficiency of drilling long horizontal methane drainage boreholes in coal. Borehole survey data are electromagnetically transmitted from the WSS7s downhole guidance probe, via the drill rod, to the uph'ole subsystem in less than 1 min per survey transmission, regardless of borehole depth. The WSS7s in-mine test consisted of providing borehole survey data during the directional drilling of a 2,538-ft horizontal methane drainage borehole in the Pittsburgh Coalbed. By considering available drilling time, which does not include hydraulic drill downtime and the time spent traveling portal to portal, 24 shifts were needed to complete the borehole. Of the available drilling time during the tcst, 50 pct of the time was spent drilling and 50 pct surveying and maintaining the WSS to keep it operational. Previous Bureau experience indicates drilling efficiency was increased 108 pct because of the WSS, in comparison with using a commercially available wire-run directional survey instrument at 10-ft intervals.

Jan 1, 1990

By Manuel Gomez

The purpose of this study was to evaluate the feasibility of using statistical response surface regression analysis to predict the sulfur and ash distributions and the washability characteristics of coal along a seam in advance of mining. Prediction equations were developed with experimental data from channel, bench, and core samples from the Pittsburgh coal seam in Greene County, Pa. It was not possible, with the available experimental data, to construct mathematical models to predict ash and sulfur concentrations between sample points. In the authors' opinion, however, the good agreement between experimentally determined and predicted values at given sample points demonstrates the usefulness of the method. More input data, such as geologic information, seam characteristics (rock-to-coal ratio), petrographic analysis, and chemical data, would perhaps make it possible to predict sulfur and ash concentrations and washability characteristics between sample points.

Jan 1, 1970

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By James C. Barker

Gold placer deposits along the upper Yukon River, in the region between the river villages of Circle and Eagle, were investigated by the Bureau of Mines. The investigation was conducted intermittently between 1976 and 1985 as part of an evaluation of mineral resources on lands proposed for inclusion in the National Park System. At least 230,000 troy ounces (tr oz) of gold has been produced in the region, principally from Woodchopper, Goal, and Fourth of July Greeks. The placers are underlain by, or occur downstream of, early Tertiary sediments that have been deposited in the Eagle Trough. Strike-slip displacement along the Tintina Fault is responsible for creation of the trough and may have been a factor in the formation of the present placers. Placers were found to have a close spatial correlation to certain altered fault lineaments of the Tintina Fault trench. Placer concentrates contain several different textural forms of gold, suggesting multiple origins. Geological studies and a survey of 162 panned concentrates throughout the region indicated previously unreported sites of placer gold, and potential exists for the discovery of additional placer and lode gold. Because of nearly continuous soil and vegetation cover, further evaluation of the region will require subsurface sampling.

Jan 1, 1986

By Robert S. Sanford

"INTRODUCTION AND SUMMARYThis paper is one of a series recently undertaken by the Mining Branch, Bureau of Mines, College Park, Md., to describe current practice in hauling ore and waste by truck at various mines.Heavy-duty ore trucks are replacing railroads at many large open-cut mines and even at a few underground mines. Recently a few mines have been equipped with trucks for transporting ore to a central point, from which conveyor belts move the ore out of the mine. This paper deals only with truck haulage methods and costs.The requirements for efficient low-cost truck haulage are good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers.A correct balance must be maintained between the primary crusher capacity, the number of shovels loading ore, and the number of trucks hauling ore.The cost of tires is important. Tire companies are manufacturing better tires. Mining companies are prolonging the life of tires by building better roads and maintaining correct tire pressure.The trend is toward heavier equipment. In 1949 it cost $0.0925 a long ton to haul ore and waste with a 15-ton truck and $0.0743 a long ton with a 22-ton truck.When trucks are properly maintained, hauling costs do not increase with the age of the trucks. During 1948 it cost $0.1118 per long ton to haul with the four oldest 15-ton trucks and $0.1130 per long ton to haul with the four newest 15-ton trucks, two of which were purchased in 1945 and two in 1947.The weighted ayerage cost of hauling a long ton of ore to the crusher and waste to the dump has been reduced from $0.1159 in 1948 to $0.087 in 1949."

Oct 1, 1950

By G. S. Rice, H. P. Greenwald

"Experience and experiment have goth shown that a cloud of coal-dust in air can be inflamed and an explosion developed only when a certain minimum concentration of the dust in air has been equaled or exceeded. Those who have had experience in the handling of coal know that dust is frequently present in the air and may be of sufficient density to obscure an ordinary electric light at a distance of 40 or 50 feet; yet flames may be, and times without number have been, introduced into such clouds, when no additional coal-dust has been stirred up, with no effect other than the burning of the dust particles which actually enter flame. Evidently the density of the dust cloud is insufficient to give self-supporting combustion.The minimum amount of dust in air required to give a spreading flame will vary with a number of factors such as the composition of the dust and its size. This amount in a unit space may be considered analogous to the lower limit of inflammability of fire damp (methane) in air, although the variation in limit of explosibility of gas is small even when conditions of the experiment are altered. In large-scale determinations of the lower limit of inflammability of coal-dust there is no certain method by which a sample of the dust cloud can be snatched and its density determined. It is necessary to produce the best possible dust cloud from a known weight of dust, in a known volume and assume - probably with considerable error - that the dust cloud is reasonably uniform. The dust cloud must be formed and the source of ignition applied to it simultaneously; this is generally accomplished by the use of blow-out shots of black blasting powder, dynamite, or similar explosive so prepared as to blow out like a cannon shot, or by a gas explosion. The more violence attending the source of ignition, the greater is the probability that all the dust is raised in a uniform cloud; and the greater the length or intensity of the flame, the greater are the chances of ignition. As a result one may obtain a variation in apparent minimum density with different sources of ignition. This difference is more apparent than real and must remain until devices for instantaneous sampling of dust clouds during explosions are perfected."

Aug 1, 1931

By V. E. Erwin, W. W. Adams

"INTRODUCTION This report presents statistics of accidents at coke ovens in the United States during the calendar years as 1933, the twenty-first year for which data of this kind are available, 1913 being the first year for which accident reports were collected from the operating companies by the Bureau of Mines. The present report is presented in mimeograph form because insufficient funds are available for printing it. The first report of the Bureau of Mines that contained statistics of accidents for the coke-mining industry in the United States covered the two calendar years, 1913 and 1914. While the figures presented therein related both to beehive and by-product ovens, the original returns from the operating companies were not classified so as to permit the presentation of accident statistics for each class of ovens separately. Beginning with 1915, the accident reports from the operating companies have shown the general type of ovens to which the reports related; therefore, since that year, separate statistics for each of the two classes of ovens have been given in the Bureau's yearly reports of accidents at coke ovens.The coke-making industry in the United States established a safety record in 1933 almost equal in merit to that which it achieved in 1932, when the accident-frequency rate was the lowest and therefore the most favorable that the industry has known. Credit for the achievement is due almost entirely to companies operating byproduct ovens. (See table 8.)"

Mar 1, 1935

By E. Chin

The mineral industry of Bangladesh was totally dominated by natural gas production and its downstream uses. A small amount of cement was produced, and clays were used locally for ceramics and construction materials. Nitrogenous fertilizer was produced from natural gas and a modest, scrap-based steel industry produced steel for local consumption. The country has been developing and using its abundant and inexpensive gas reserves as fast as practical. The population, however, was predominantly dependent on agriculture for its livelihood. The industrial sector accounted for 10% of the economy, and most of the industrial output was directly associated with agricultural products jute, tobacco, and textiles. Industrial expansion, even with the availability of gas, was severely constrained because of limited domestic demand, lack of skilled work force and management, poor infrastructure, and a low rate of domestic savings. To put greater emphasis on the industrial sector, the Government established a National Committee for Industrial Development in July. The Committee instituted policy reforms in the areas of trade and investment. One important step was to move from a positive import list to a negative list, thereby permitting imports of items not restricted or banned. The system for recovering and approving new domestic or foreign industrial investments was streamlined to expedite what had become a cumbersome, bureaucratic exercise. To encourage industrial development in areas away from the crowded urban centers, several economic incentives reportedly were adopted. These included a reduced tax rate on imported machinery, exemption of import license fees, a reasonable debt equity rate, and a 9-year income tax exemption period.2 In the trade sector, imports increased 12% in fiscal year (FY) 19843 mainly

Jan 1, 1987

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550- and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By Thomas R. Bur

Symmetry theory, based on ground work established in the study of single crystals and experimental procedures utilizing ultrasonic pulse velocities of spherical specimens plotted on equal area polar projections, enables the direct identification of a material's elastic symmetry system and the determination of its orientation, as well as the position of the elastic coordinate axes. The method is especially useful for elasticity studies of polycrystalline and amorphous materials for which this knowledge of symmetry is a prerequisite in determining the independent elastic constants. Projections based on theoretically derived velocities are given for a single crystal from each of the major crystallographic symmetry systems except the triclinic. Projections based on experimentally derived velocities are given for one brass and several rock spheres.

Jan 1, 1969

By John S. Berber

Bureau of Mines research on the production of phthalic anhydride by vapor phase oxidation of hydrocarbons began at Morgantown, W. Va., in October 1960. For these preliminary studies, a known solution containing naphthalene and 1-methylnaphthalene was used. In another series of tests, pure naphthalene was dissolved in different solvents. A series of investigations was conducted with the neutral oil fraction (210° to 270° C) of a low-temperature tar obtained from the Texas Power and Light Company's low-temperature carbonization unit. The neutral oil fraction was first dealkylated, and then the product was distilled into 210° to 250° C and 250° to 270° C fractions. These two fractions were then subjected to catalytic vapor phase oxidation. Although a number of catalysts was tested, most of the experiments were made using 9 percent vanadium pentoxide on inert alumina. The activity of this catalyst did not decrease after 162 hours at 1,030° F. Studies were conducted over a temperature range from 610° to 1,180° F. An operating temperature of 1,030° F yielded 47.50 percent of phthalic anhydride from a synthetic mixture of naphthalene and 1-methylnaphthalene. The highest yield (84.40 percent phthalic anhydride) was obtained with naphthalene dissolved in toluene and also with naphthalene dissolved in methyl ethyl ketone. With a 210° to 250° C fraction the highest yield of phthalic anhydride obtained was 12.32 percent at a temperature of 900° F, and, with a 250° to 270° C fraction, it was 15.80 percent at a temperature of 875° F.

Jan 1, 1963