Search Documents

By G. Dale Cor, Will H. Coghill, M. F. Williams, I. L. Feld

"INTRODUCTION During the past several years the Southern Experiment Station of the Bureau of Mines, with the cooperation of the University of Alabama, has given attention to hydraulic classification. One of the things this work has revealed is a variability not generally recognized in the conditions of teeter at different depths. This report depicts the passage of material through a teeter column and its emergence as a classified product.The work was made possible through the development of a classifier for several hundred pounds per hour permitting a small quantity of coarse spigot material to be discharged without the usual interruptions caused by stop-pages. Previous designs of small classifiers have been unsatisfactory because the,orifice used to control the quantity of spigot product as subjectto stoppages, particularly when attempting to discharge a small quantity of although the classifier used in this work has been described in detail in a previous publication 6/ its principal features will be discussed briefly herein. The main subject matter of the paper is based upon the three figures that illustrate in panorama the conditions that exist in a classifier during the continuous classification of bituminous coal, anthracite coal, and an iron ore trailing."

Jan 1, 1946

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Harold L. Gibbs

The purpose of this paper is to encourage petrographers to prepare thin sections, as the demand for microscopic examination of rocks, ores, and metallurgical products is becoming more general in .the mining metallurgical-fields. This paper has been written with the knowledge that the successful thin-section methods and the several new techniques herein described will be helpful to all engaged in this field of work. Detailed instructions for making thin sections by methods developed at the Salt Lake-City laboratory of the Bureau of' Mines are given in this paper. Several new techniques are described for making thin sections of loose grains and fine sands and for making good thin sections of highly altered and friable rocks. The methods described insure superior bonding of the rock to the glass slide, thus virtually eliminating any failures due to parting of the section from the glass slide, and permit fast mounting, grinding, and finishing, thereby materially lessening the time required to prepare thin sections.

Jan 1, 1950

By R. C. Wang

Solid-liquid flow in different pipe geometries was investigated. This investigation was conducted by measuring delivered solids concentration and head loss. The delivered solids concentration was measured to study the effect of pipe geometry on the minimum carrying velocity above which solids do not lag behind the fluid. Head loss was measured to study the effect of pipe geometry on the friction loss. A mathematical formula was developed for determination of the minimum carrying velocity. Darcy-Weisbach's equation and Durand's equation were used for comparison of head losses of pipe shapes. Of the different pipe shapes studied, each having the same interior cross-sectional area, the rectangular pipe with the wide side oriented as the base yielded the lowest minimum carrying velocity at high solids concentrations. The minimum head loss at low velocity and high solids concentration also was attained with this pipe. Although the circular section is known to be the best for transporting liquid only, the present study suggested that pipe geometry is a factor in lowering the operating velocity and reducing head loss in solid-liquid flow.

Jan 1, 1973

By B. W. Jong

As part of the Bureau of Mines program to develop substitute or improved performance refractory materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives on sintering and strength properties of aialon (silicon aluminum oxynitride) compositions fabricated by a conventional powder metallurgy technique. Additions of Y203, Gd203, CeO2, MgO, ZrO2, ZrSiO4, and MgA12O4 to a sialon composition containing 70 pct ß-Si3N4 + 30 pct a-A1203 increased sintered densities by as much as 50 pct over densities of undoped material. The studies also indicated that sintered densities reached a maximum between 20 and 30 mole-pct a-A1203 when a series of sialon compositions of a-Si3N4, having 6.7 to 57.9 pet a-Al203, were doped with Y203, Gd2O3, and MgO. In studies to establish the effect of the crystalline phase of the silicon nitride and alumina used, tests were made using a- and ß-Si3N4 and a- and ?-A12 03 as starting materials. The tests indicated that when using an addition of 5 wt-pct Y203, best results were obtained with a sialon composed of 74.4 mole-pct a-Si304 and 25.6 mole-pct ?-A1203. In other tests made with this sialon composition MOR values of 28,120 and 29,500 psi at 25° C, and 23,520 and 16,850 psi at 1,400° C, were obtained when doping with 5 wt-pct ZrSiO4 and ZrO2, respectively.

Jan 1, 1980

By Roy H. Grau

Increased awareness of a healthy work environment is common to all industries and the stone industry is no exception. The presence of operating diesel equipment, welding, stone production blasting, and silica dust in a working environment all contribute to air quality issues in underground stone mines. Particularly recognized is the exposure of workers to diesel particulate matter (DPM). Recent regulations call for a DPM standard of 160TC ug/m3 (TC = Total Carbon). The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of these mines and consequently reduce the exposure of workers to harmful airborne contaminants. The results have shown that the ventilation of underground stone mines can be significantly enhanced using improved ventilation controls and techniques. Large-opening stone mines present specialized ventilation challenges because their entries are much larger than in other types of mines. Most stone mines have entries about 40 feet wide and up to 30 feet high, with bench areas that may extend even higher. These large entries present the positive opportunity to move large air quantities at relatively low mine fan pressures resulting in lower fan horsepower and reduced operating costs. However, the difficulty in ventilating large-opening mines is that even with large air volumes, the air velocity is often less than 100 feet/minute. Higher ventilation velocities more quickly dilute and remove contaminants from the face areas. Higher ventilation airflow velocities can be achieved by effective ventilation planning and proper choice of ventilation fans.

Jan 1, 2009

By Paul M. Tyler

Bismuth is a useful metal and rather an uncommon one . The element probably constitutes much less than one-millionth part of the earth's crust , but the potential supply - to no small extent as a by-product of the production of lead and copper with which it is associated in nature has tended for many decades to exceed the demand. A single mine in Bolivia could readily flood the world's markets , and considerable quantities of bismuth are allowed to escape recovery at many smelting plants .

Jul 1, 1931

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of certain solvents and hydraulic fluids used in underground mining operations. The following halogenated solvents were studied in view of their usefulness and their flame retardant property: tetrachloroethylene, C12C = CC12; 1, 1, 2-trichloroethane, CIH2CCHC12: and trichloroethylene, C12C = CHC1. The hydraulic fluids studied were representative of five groups approved by the Mine Safety and Health Administration for underground operation, namely: glycol-water solutions, mineral oil-water emulsions, synthetics other than phosphate esters, synthetic phosphate esters, and mixtures of phosphate esters with mineral oils and other ingredients. It was observed that the partially halogenated solvents present a greater potential toxic hazard than the fully halogenated materials, due not only to the easy production of hydrogen chloride but also to their ease of oxidation leading to the formation of phosgene and carbon monoxide. The pure phosphate esters exhibited the best thermal oxidative stability of the five groups of hydraulic fluids tested. A fluid containing phosphate esters mixed with mineral oils and other unidentified ingredients appeared to be the most hazardous On the basis that it produced very toxic acrolein and phosphine.

Jan 1, 1980

By Van H. Manning

"Under the organic act establishing it, the Bureau of Mines is authorized to conduct investigations designed to improve health and safety conditions in the mineral industry and to promote efficient development and utilization of our mineral resources. The field of the Bureau's activity, therefore, begins with the commercial development of mineral deposits and ends with the production and utilization of the final marketable product.In order to serve more efficiently the various sections of the country, the Bureau has established, in addition to its main offices at Washington, D. C., eleven field experiment stations, three field offices and several mine rescue cars and mina rescue stations. These field branches are so distributed as to cover most of the mining districts of this country, including Alaska. The field service in general deals with specific experimental problems, cooperative work with non-governmental institutions, and mina rescue work, while the Washington office is the administrative head and is responsible for the distribution of general information, the chiefs of the technical and administrative divisions of the Bureau being stationed there.The Bureau is prohibited by law from doing work exclusively for the benefit of any private company or individual. Generally speaking, the Bureau does no assaying, ore testing, or similar service work for the benefit of private companies or individuals. In response to requests for work of this sort a list of assay and ore testing laboratories is supplied. In referring inquiries to com-mercial laboratories or consulting engineers, care is taken to mention several names so as to avoid designating any one establishment or engineer."

Apr 1, 1920

By Richard G. Sandberg

Sphalerite concentrates prepared during processing of Missouri lead ores contain small percentages of cobalt and nickel which adversely affect zinc electrolysis. The Bureau of Mines has evaluated solvent extraction and precipitation techniques to remove and recover cobalt and nickel from zinc sulfate solution prior to zinc electrolysis. Prepared zinc sulfate solutions containing about 190 gpl of zinc and 50 ppm of both cobalt and nickel were treated using various combinations of complexing reagents, solvent, pH, concentration, time, and temperature. The following complexing reagents gave the best results: a-nitroso-ß-naphthol, ß-nitroso-a-naphthol, 1,2 cyclohexane dione dioxime (nioxime), di-2-pyridyl ketone oxime, and dimethylglyoxime. These reagents in suitable solvents lowered the cobalt and nickel levels to <0.1 ppm. Stripping the complexed reagents from the solvents was not possible except for nioxime. Direct addition of the appropriate reagent to the prepared zinc sulfate solution resulted in the precipitation of cobalt and nickel. Several possible flowsheets are presented for the removal and recovery of cobalt and nickel. Good zinc deposits were successfully electrowon from zinc sulfate solutions purified by solvent extraction and precipitation.

Jan 1, 1978

By Martin H. Stanczyk

Ultrafine grinding of the industrial minerals mica, pyrophyllite, talc, marble, barite, and fluorite was accomplished using the Bureau-developed and patented attrition-grinding process. The materials, representing minerals of diverse physical characteristics, were batch ground in a 10-inch-diameter machine using statistically designed experimental test programs. The tests were made to determine large effects of variables such as feed pulp density, grinding medium size, and quantity of the electrical energy consumed during grinding on product particle size and bulk density. In designing the test programs, it was assumed that there was no interaction between the variables. Relatively coarse commercial flotation concentrates of mica, barite, and fluorspar and mine-run products of pyrophyllite, talc, and marble were readily ground into subsieve size ranges. Considering the great amount of particle size reduction obtained, the electrical energy requirements for grinding were very low. In general, the test results indicated that the best conditions for particle size reduction were approached when grinding with the coarser fraction of sand grinding media, the higher-sand-to-mineral weight ratio, and the higher feed pulp density.

Jan 1, 1972

By C. M. McCulloch

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By H. E. Perlee

Mathematical expressions are derived for the histories of the pressure, flame radius, mass fraction burned, and burned and unburned gas temperatures associated with a spherical flame propagating concentrically in a spherical vessel. The equations are solved numerically for a 9.5 pct CH4/air mixture using the best available information for the burning velocity, expansion ratio, and specific heat ratio. Calculated histories are in complete accord with experimental measurements. The accuracy of calculated histories is determined relative to errors in the system parameters, and it is found that 10 pct errors in either the burning velocity or the expansion ratio results in a 40-pct error in the pressure history. A 10-pct error in either burned or unburned specific heat ratio results in a 22-pct error &apos;in the pressure history. It was further established that the usual assumption of constant specific heat ratio is unacceptable, but equating the burned and unburned specific heat ratios result in no apparent error in the histories. The cubic law (P = Kt3 + Po) is derived and discussed, and it is found that the law is valid only during the early period (P<2 atm) of flame growth.

Jan 1, 1974

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By Isaac A. Zlochower

This paper presents data on the limiting (minimum) oxygen concentration (LOC), in the presence of added N2, of methane (CH4), propane (C3H8), ethylene (C2H4), carbon monoxide (CO), and hydrogen (H2), and some of their binary mixtures. It also addresses the issue of the flammable concentration (flammability) limits of these pure gases in air. The study is based on spark ignited explosions in large, spherical laboratory vessels (120-L and 20-L) using a 7% pressure-rise criterion for explosion propagation. The results of the study are compared with the older values which used long flammability tubes with a diameter >5 cm together with visual evidence of substantial upward propagation. They are also compared to results reported recently using a 12-L spherical flask with a visual flame propagation criterion. Finally, they are compared to results reported in Europe using more modest flammability criteria and smaller chambers. The findings reported here show excellent agreement between the 120-L and 12-L results, good agreement with the 20-L results, and reasonable agreement with the earlier flammability tube values for the lower flammability limits. They disagree, however, with the more conservative European values. These results and those from the 12-L experiments also feature lower LOCs than are given by traditional flammability tubes. A model for the LOCs of such fuel mixtures based on the Le Chatelier mixture rule for lower flammable limits is seen to reasonably fit the observed results on binary mixtures and can accommodate more complex mixtures as well. One such set of ternary mixtures containing CH4 and 1:1 CO:H2 is well fitted by the model.

Jan 1, 2009

By H. W. Davis, Richard J. Lund

"In presenting the results of this survey on consumption of ferrous scrap and pig iron for the year 1935 the Bureau of Mines, responding to requests from industry, seeks to fill a major gap that has long existed in the field of metalliferous raw-material statistics. This type of information is designed to meet the needs of: (1) Consumers of ferrous scrap. including operators of blast furnaces, steel mills, ferrous foundries, and rolling mills; (2) marketers of scrap iron and steel, including large brokers who sell, and dealers who collect, prepare, and sell the material; (3) large scrap producers; (4) producers of iron ore, with which scrap competes indirectly; and (5) other individuals and agencies interested in more general economic analysis, since the scrap market has repeatedly been cited as one of the most sensitive of all industrial barometers, If the survey prover as useful as now seems probable, it will be continued annually with possibly an enlarged scope of treatment.The Bureau appreciates that its first efforts in this field may not meet all expectations: but it hopes to develop gradually, through suggestions, advice, and criticism from the industrial groups most interested, a type of analysis that will accord closely with technical processes and best meet the needs of all groups vitally interested in supplies and use of ferrous scrap. Constructive criticism and suggestions from industry regarding improvements to be desired in the conduct of future surveys on this subject will therefore be warmly received by the Bureau."

Nov 1, 1936

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D&apos;Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Comprehensive ventilation surveys are made to review the adequacy of the mine system with regard to both statutory requirements and/or company policy, to evaluate improvements to the current ventilation system and to plan for £stun expansion. If computer simulation is to be used for these purposes, accurate quantity and pressure measurements become an absolute necessity since the validity of the computer generated output is heavily dependent on the accuracy of the input data. Consequently ventilation surveys that are run to generate input data for computer simu¬lation must use the best data collection procedures to guarantee as accurate results as are possible. These requirements have led to modifications in procedures that are used for routine ventilation surveying. McElroy and Kingery (1957) have recommended that pressures be measured independent of quantities since minor changes in mine conditions have a greater effect on absolute pressure measurements than on quantity measure¬ments. They estimate that, for large mines, a pressure survey may take only 1 to 3 days while the corresponding quantity survey would require 1 to 3 weeks. Although this procedure would undoubtedly lead to more ac¬curate pressure measurements, its use for the development of computer input data is not recommended for the following reasons. Atkinson&apos;s equation, H = RQ2, is used in computer oriented analysis to develop the airway resistance, R, based on quantity and pressure loss measure¬ments. It can easily be seen that since R a 1/Q2 and R a H, the effect of errors in quantity measurement is, in fact, more significant than those in pressure measurement. If the quantity and pressure measure¬ments are made at different times another problem results. Minor changes in quantity that may occur in the time between the pressure and quantity

Jan 1, 1977

By Ramie H. Thompson

1.1 BACKGROUND In many underground coal mining operations the use of electromagnetic field equipment, particularly communication systems, not only increases the overall efficiency of the mining operation but can be directly linked with mine safety considerations. The use of electromagnetic field producing equipment in underground coal mining operations can only be expected to grow. Several new communication systems have already been proposed. In addition, high-frequency producing equipments for many diverse uses in mining operations are under study. The use of these equipment in underground mining operations is hampered by the possibility of their electromagnetic fields interacting with the electric blasting cap operations commonly carried out in the mines. Such interactions can have at least two results bearing directly on mine safety: o premature initiation of the cap, either in its normal shot location or during hookup or transportation; o dudding of the cap so that normal firing operations do not cause irritation; thereby leaving unexploded high explosives after normal firing. Since the consequences of a premature initiation could, particularly in coal mines operations, result in catastrophe involving human life, the overall approach to prediction of possible hazard must be, as far as possible, of a "worst case" nature. The general problem of predicting possible RF hazards for any electroexplosive device (EED) is best treated by reference to Appendix A of

Jan 9, 1983

By A. L. Johnson

In this Bureau of Mines report, time-resolved infrared emission spectra and corresponding pressure and temperature histories are reported for large-scale propagations of CH4-air, CH4-air-N2, and CH4-air-CF3Br ignitions in a 12-ft-diam sphere. Absolute spectral radiances were obtained throughout combustion over the 1.6- to 4.8-gym range, and the radiance growth patterns for the H20 (2.5-µm) bands are presented as a function of methane stoichiometry and diluent concentration. Flame temperatures were determined from the C02-band emissions, which approximated unit emissivity shortly after ignition. Burning velocities are also given for some of the test-mixture compositions. Measured flame temperatures were in excellent to fair agreement with theoretical adiabatic values for the CH.-air and CH4-air-N2 mixtures; the best agreement was for the stoichiometric CH4-air mixture. The CH4-air-CF3Br mixtures with =2 pct CF3Br gave poor agreement with theory. The measured temperatures were significantly lower during the early stage of combustion; furthermore, the later stage of combustion was uninhibited and yielded unexpectedly high pressures. Supplemental data from a 2-ft-diam sphere at various initial pressures confirmed that the CF3Br inhibition effectiveness decreases with increased pressure. The possible effects of buoyancy, turbulence, and changing kinetics are discussed.

Jan 1, 1977