Search Documents

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 2010

By R. S. Conti

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide (CO) sensors, and a point type heat sensor (PTIIS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s, The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS, A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and C8 sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity, Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners' escape.

Jan 1, 2010

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By Travis Q. Lyday

Australia was one of the world's principal producers of minerals and metals, and its minerals industry was a leading catalyst in promoting growth of the country. Australia was the world's largest producer of alumina, bauxite, diamond, ilmenite, monazite, opal, rutile, sapphire, and zircon. It was the premier exporter of alumina, coal, ilmenite, refined lead, monazite, rutile, and zircon, and was the second leading exporter of iron ore, after Brazil. Ranking behind China, the United States, the U.S.S.R., the German Democratic Republic, Poland, and the Federal Re-public of Germany, Australia was the seventh largest producer of coal (all grades) in the world. Australia was the fourth largest gold producer in 1988, after the Republic of South Africa, the Soviet Union, and the United States. It was the second largest producer of zinc, the third largest producer of nickel, the fourth largest producer of uranium, and the seventh largest producer of copper. 2 The country's mineral wealth was so extraordinary that it was virtually self-sufficient in most mineral commodities. Endowed with abundant resources of coal, natural gas, liquefied petroleum gas, and uranium, Australia was one of the few market economy countries that was a net exporter of mineral fuels. About 90% of Australia's consumption of crude oil was supplied by domestic production; this was expected to decline significantly about 1990, unless significant new oilfields were discovered.

Jan 1, 1990

By Ludwig Schmidt

The attention of operators of oil-producing properties long has been directed toward methods of' disposing of petroleum wastes as well as the disposal of oil-field brines. The problem of disposing of' petroleum wastes is not easy to solve, and although many operators are to be commended for the efforts they have made, much work remains to be done before the problem can be considered solved. Petroleum wastes include emulsions of petroleum and brine or mixtures of petroleum and sand that cannot be "broken down" or treated economically by known methods of separating petroleum from deleterious matter; crude petroleum that escapes from pipe lines, fittings, and tanks because of holes in the lines, leaky connections, or some accident; and oil-saturated materials that accumulate accidentally or otherwise an the normal operation of an oil-producing property.

Jan 1, 1938

By E. C. Lane

This paper is the second report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relating to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 31293. A third and concluding paper giving the results of other tests will be published as soon as these tests have been completed. The present paper deals with the data of the twenty-third semiannual survey presented in accordance with the revised specifications for United States Government motor gasoline. The sample numbers used are identical with those used in Report of Investigations 3129, with additional data included for copper strip corrosion (method 530.22).4 and sulphur content by the lamp method.5 Three hundred and twelve samples were collected and analyzed in this survey. Two hundred and seven samples were competitive-price gasolines and one hundred and five samples were premium-price motor fuels.6

Jan 1, 1931

By D. J. Bauer

A primary amine extraction system was investigated for fractionating a cerium-group, lanthanide sulfate mixture. Addition of diethylenetriaminepenta-acetic acid (DTPA) to the amine extraction system resulted in separation factors as high as 5.4 for lanthanum-cerium, 8.0 for cerium-praseodymium, 3.7 for praseodymium-neodymium, and 7.0 for neodymium-samarium. In multistage studies on a cerium-free lanthanide mixture, 96 percent of the lanthanum was recovered with a purity of 95 percent.

Jan 1, 1968

By Norman G. Foster

The mass spectra of 14 previously unreported alkylthiophenes are pre-sented. Low ionization voltage data of selected compounds from these 14 and 23 previously reported alkylthiophenes are presented and discussed for their value in supporting fragmentation mechanisms analytical correlations. A comparison with and corroboration of earlier correlations is made. Additional correlations concerning detection of side chain branching and the detection of ethyl-alkyl and propyl-alkylthiophenes are made. A discussion of the possible fragmentation routes and mechanism of fragmentation is given. Speculative structures are inferred s out some of the ions and hence this work provides a basis for suggesting fation mechanisms for the alkylthiophenes according to modern theories ass spectrometry. Verification of these mechanisms must await the availability of isotopically labeled molecules which are labeled in specific lotions that permit the definition of the paths of frag-mentation. Some suggestions for further work to generalize on the correlations and studies made to this point are presented.

Jan 1, 1965

By Raymond B. Ladoo

SOAPSTONE

Feb 1, 1922

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

By M. J. Ankeny

This is a study of 58 fatal haulage accidents investigated by Federal coal-mine inspectors during the period January - June 1951. The information presented in this circular was obtained by analyzing fatal haulage accidents in 33 bituminous-coal producing counties representing 11 States. The physical conditions represent a cross section off producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of large modern mechanized operations. These data are thought to be representative of haulage conditions within the bituminous-coal mining industry and are submitted to follow up the Information Circular 7604 ?Analysis of Haulage Fatalities in Bituminous-Coal Mines - 1950.? Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the problem of haulage safety is complex. It is subject to constant change and is comprised of numerous influencing variables, which are not always obvious. The solution to this problem will not come through the application of any standard formula or mechanical approach since the inherent factors are strongly influenced by the human equation, and the chain of circumstances is further affected by expediency.

Jan 1, 1951

By McHenry Moiser

"SUMMARY This mine, which was discovered in 1846, was active in the 1850's, in the 1870's, and again in 1883. Since this last date, it has been idle. Two parallel bed-veins in lower Silurian limestone, about 50 feet apart, strike N. 70° E. and dip 70° NW. The north vein had an average width of 12 feet to a depth of 50 feet, where it was barren. The south vein had an average width of 16 feet to a depth of 75 feet; on the 110-foot level, although well-defined it carried little or no values. The zinc content of the ore was as high as 12 percent, and some lead and silver were associated with it. A reduction plant for production of spelter and zinc oxide was constructed at the mine. The only available record of production is for 1873 to 1876, inclusive, when 357 tons of smelter was shipped. The mine is caved and inaccessible, and nothing now remains of the treatment plant.Four holes totaling 1,046 feet wore diamond-drilled to probe for extensions of the ore in depth. Core recovery was about 85 percent. No samples were taken for analysis.INTRODUCTION AND ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The policy of the Bureau is to publish the facts devel¬oped by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The deposit was examined in 1944 by C. B. White, mining engineer of the Bureau of Minos. Diamond-drilling was under the immediate supervision of McHenry Mosier. 2/ The diamond-drill cores were logged by Arnold Brokaw, geologist, Federal Geological Survey, and 'wore filed in the core library of the Bureau of Mines, Mount Weather, Va."

Jun 1, 1948

By P. A. Richardson

The current Bureau of Mines active list of permissible explosives includes 76 brands. Eleven are gelatinous and the rest are the granular type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1970

By T. E. Gray

This report describes the preparation characteristics of the three significant coal beds in Greene County, Pa. It is one of a series planned to determine which coals are suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 12.5 million tons of coal was produced in Greene County in 1956, of which approximately 10 million tons was cleaned mechanically in 8 cleaning plants. The Bureau of Mines has estimated that 3.5 billion tons of recoverable coal remained in the county as of January 1, 1954.

Jan 1, 1958

By C. H. Riggs

This report describes the geology and reviews the oil-production history of the Dutcher sands of Pennsylvania age in the Muskogee oilfield. The geology and production history are presented not alone as a review of the past behavior of the field but also to interpret the possibilities for future production of oil from semidepleted sands in this and similar areas. The Muskogee field, one of the oldest oil-producing areas in Oklahoma, yields paraffin-base oil of 40° API gravity -a gravity higher than that of most Oklahoma oils. Oil was discovered in the townsite of Muskogee in 1894 but was not produced in commercial quantities until 1904. A peak yearly rate of 1,340,000 barrels of oil was attained in 1910 (see table 1).

Jan 1, 1959

By Leonard Obert

Between 1927 and 1957, sodium borate minerals were mined by underground methods in the Kramer District, Kern County, Calif. In 1957, surface mining methods were initiated, and during the next two or more decades it is probable that most of the production from the district will be obtained from open pits. However, part of this borate deposit is sufficiently deep that surface mining may not be economical and, hence, at some future date underground methods may again be employed. This report was prepared to document the underground mining methods employed in the district before 1957. The general geology of the district and the detailed geology of each of four mine sites are presented, together with a mineral and mechanical description of the ore and enveloping rock. The report also describes the stoping, extraction, pillar support, methods of artificial support, and other factors that affect the structural characteristics of these mines.

Jan 1, 1962

By H. R. Shell

To obtain a better understanding of the crystallization of fluoride containing amphiboles from melts, an investigation of the range of stability between fluoramphi-boles and other minerals was conducted by the Bureau of Mines. This study has shown that the stability of fluoramphiboles is strongly influenced by both fluoride concentration and isomorphic replacement. Over 150 reactions were made with different compositions and reaction conditions. substitutions attempted and the phases that formed when the composition was crystallized by cooling from the melt are discussed. The attainment of equilibrium in these multicomponent systems is not claimed. Many ions that would be expected to enter the amphibole structure instead resulted in crystallization of phases other than amphibole. Those compositions that resulted in a high yield of acicular fluoramphibole by crystallization from the melts are shown in table 2. The fluoramphiboles obtained from melts typically had an acicular crystal habit and a hardness of 6 to 7 on the Mohs' scale. Although many had relatively high length to cross section ratios, none were fibrous; it was concluded that the possibility of synthesizing a fibrous fluoramphibole from a melt was low. However, many compositions can be crystallized into a tough, hard, impact-resistant mass of interlocking acicular crystals.

Jan 1, 1958

By Ralph B. Youtz

This paper describing mining methods at, the Eighty-Five mine of the Calumet and Arizona Mining Co., Valedon, N. Mex., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts in the United States. The Eighty-Five mine is in southwestern New Mexico, 3 miles southwest of Lordsburg, Hidalgo County (see fig. 1). The mine produces normally 7,000 to 8,000 tons per. month of silicious copper-gold-silver ore, and employs approximately 200 men underground and 40 on-the surface. Mining is done by shrinkage and cut-and-fill methods.

Jan 1, 1931

By V. F. Parry

"INTRODUCTION During the war period the Bureau of Mines expanded its investigations on western coals principally in connection with Investigations of raw material resources for western steel production. Owing to the expansion of the steel industry, there was some concern regarding the availability of suitable coking coals; end because of the potential steel shortage, the production of sponge iron, using the lower-rank fuels, was considered. Work was conducted by the Bureau of Mines on exploration projects and on testing of coals both at the Central Experiment. Station at Pittsburgh, Pa., and at the Bureau of Mines Station at Golden, Cole.The results of these investigations are being published by the Bureau in several reports of investigations and technical papers. In making this resume of coal investigations, the work done by the Bureau of Mines at Pittsburgh in the Mining and Coal Carbonization Sections will be discussed and the investigations at Golden described in greater detail.INVESTIGATIONS OF WESTERN COALSThe Mining and Coal Carbonization Sections of the Coal Division, Bureau of Mines, under the supervision of A. L. Teeny es and J. D. Davis, respec¬tively, conducted many field investigations to locate and evaluate new sources of coking coals. Drilling explorations were made in Colorado, Wyoming, Utah, New Mexico, and Washington and revealed two important new reserves of coking coal. The first one studied was the Willow Creek bed at Kemmerer, Wyo., which was reported in 1945.3/ A recoverable reserve estimated at 11,200,000 tons was blocked out, and samples of coal were extracted for coking tests. The coking properties of the coal were not quite equal to those of Sunnyside coal, but it was indicated that a 50-percent blend of the Willow Creek with Lower Sunnyside will produce a satisfactory metallurgical coke based on Columbia steel standards."

Jan 1, 1948

By E. C. Lane

This paper is the second report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relating to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 31293. A third and concluding paper giving the results of other tests will be published as soon as these tests have been completed. The present paper deals with the data of the twenty-third semiannual survey presented in accordance with the revised specifications for United States Government motor gasoline. The sample numbers used are identical with those used in Report of Investigations 3129, with additional data included for copper strip corrosion (method 530.22),4 and sulphur content by the lamp method. Three hundred and twelve samples were collected and analyzed in this survey. Two hundred and seven samples were competitive-price gasolines and one hundred and five samples were premium-price motor fuels.

Jan 1, 1931