Search Documents

By A. Salmoni, E. K. Gillin, T. Eger, A. Cann, P. Vi, M. Hunt

Kittusamy (Kittusamy & Buchholz, 2004) state that there have been few studies conducted to assess exposure to whole-body vibration (WBV) in the construction industry. They suggest that there is very little reliable data from the construction industry that characterizes exposure levels to various hazards including WBV or the health outcomes from such exposure and that there is a need for more exposure data. In a recent exploratory study of heavy construction equipment Cann (Cann, Salmoni, Vi, & Eger, 2003) looked at vibration levels for 14 different types of construction equipment. Eight of the 14 pieces of equipment tested exposed operators to levels of WBV that exceeded the recommended limits for an 8-hour period when comparing the measured VDV to the ISO 2631-1 standards. The purpose of the present research was not only to test a larger number of scrapers but also to investigate scraper operator exposure to whole body vibration (WBV) separately for each task. Methods 33 scrapers were evaluated for WBV in a variety of residential and road construction projects. Testing equipment consisted of triaxial accelerometers that allowed vibration data collection in all three orthogonal axes, with the x-axis positioned to measure vibration in the anterior-posterior direction, the y-axis in the medial-lateral direction, and the z-axis in the vertical direction. Root mean square accelerations (aRMS), vibration dose value (VDV), crest factor, and maximum transient vibration values (MTVV) were derived from this software and exported to an Excel™ spreadsheet for later data analysis. Test sessions for each piece of equipment lasted for approximately 20 minutes until at least three work cycles had been completed. Tasks included: idling while waiting for a bulldozer to push the scraper through the scraping phase, scraping, traveling loaded with dirt, dumping and traveling empty. Results Task breakdown by time reveals 25% of the work cycle was spent traveling fully loaded with dirt, 19% dumping, 21% traveling unloaded, 17% idling and 18% scraping. Calculation of aRMS vector sums gave values of 2.55 m/s2 during loaded transport, 2.46 m/s2 during dumping, 2.31 m/s2 during unloaded travel, 0.55 m/s2 during idling and 1.46 m/s2 during scraping (see Table 1). The highest acceleration values recorded were found in the z-axis during fully loaded transport reaching an average aRMS over three work cycles of 2.55 m/s2.

Jan 6, 2006

By J. W. Eckerd

The crushing of chestnut-size (1-5/8 by 13/16 inch) Pennsylvania anthracite in four commercial crushers (impact) jaw) hammer-mill) and gyratory types) was studied by the Bureau of Mines to determine which could produce the largest proportions of buckwheat Nos. 1 and 2 sizes (9/16 by 3/16 inch). Single pass dry and wet crushing techniques and the effect of stage crushing were evaluated. Calculations were made to show the effect of closed-circuit reduction on production rates and yield of the various sizes. The data show that the gyratory crushers produced the greatest percentage of the desired sizes. A ring-type hammer mill produced the greatest tonnage of buckwheat No.1 and rice (14.9 tons per hr.) during dry grinding tests) but the yield of these sizes was only about 55 percent) as compared with 62 to 70 percent for the gyratory crushers. The impact and jaw crushers produced the smallest amount of buckwheat and rice and the largest quantity of oversize material.

Jan 1, 1960

By Douglas D. Reynolds

Intense vibration can be transmitted to the hands and arms of workers who use hand-held percussive or vibrating devices, tools, and work pieces. Continued habitual exposure to vibration directed to the hands can cause patterns of various symptoms associated with hand-arm vibration syndrome (HVAS). The International Organization for Standardization (ISO) first published ISO 5349 in 1986.3 This standard specified methods for measuring and evaluating vibration directed into the hands from hand-held vibrating devices, tools, and work pieces. The American National Standards Institute (ANSI) published ANSI S3.34 the same year.1 This standard was modeled after ISO 5349-1986 and specified methods for assessing exposure to hand-arm vibration. The Parliament of the European Union has issued the European Union Human Vibration Directive-2002/44/EC, which specifies vibration daily exposure action values (DEAV) of 2.5 m/s2 and daily exposure limit values (DELV) of 5.0 m/s2. These values have generally been accepted by medical experts, scientists, and engineers in governmental agencies, research institutions, and industry in the USA and other countries.2 When they are achieved, they will reduce the potential for the development of symptoms related to HAVS among workers exposed to hand-arm vibration. Significant improvements in measurement and analysis instrumentation, miniature and subminiature accelerometers, and medical diagnostic and assessment protocols have being introduced since 1986 when ANSI S3.34 was first published. In response to these improvements and the introduction of the EU Human Vibration Directive, ANSI Working Group S2.39 developed the revision to ANSI S3.34, which has now been published as ANSI S2.70-2006.2 Method ANSI S2.70 specifies the use of the hand-arm vibration measurement procedures outlined in ISO 5349, Parts 1 and 2.2,4,5 It requires the measurement of ISO frequency-weighted acceleration values in three mutually orthogonal axes of vibration. These values are then vectorially added to obtain the vibration total value, ahv: [ ] where ahwx, ahwy, and ahwz are the measured r.m.s. ISO frequency-weighted acceleration values in the x, y, and z directions, respectively. If multiple vibration exposure events are experienced during a work day, the overall vibration total value is obtained from: [ ] where ahvi is the vibration total value of the ith operation, Ti is time duration in hours of the ith operation, n is the total number of operations, and T is total time in hours associated with the n

Jan 6, 2006

By Henry P. Chandler

COMBINED sales of abrasive materials in the United States during 1956 increased at about the same rate as the value of the Gross National Product in terms of 1954 dollars,3 which was nearly 3 percent. However, some segments of the industry did not follow the general pattern. Sales of abrasive grinding wheels increased 9 percent in value. Sales of surface-coated abrasives declined 5 percent in quantity hut increased 1 percent in value, Production of crude silicon carbide in the United States and Canada advanced both in tonnage and value, but that of abrasive-grade [ ]

Jan 1, 1958

By Alice Turcot

Knowledge of risks from exposure to hand-arm vibrations is usually presented by clinicians and researchers from a medical and engineering point of view. There is a strong need to develop innovative health promotion programs for exposed workers. Risk perceptions by vibration exposed workers and HAVS (hand-arm vibration syndrome) affected workers are less well known. In 1983, Brubaker demonstrated that 75% of studied fellers thought that whitening of the fingers was part of the job and/or an unrelated nuisance, while only 25% believed it was a disease. 1Grounds also showed that even though there were a very high number of forestry workers with white fingers, none considered quitting because of their condition. 2 It seems that many workers hesitate to declare the illness or believe they are less affected than they really are, perhaps from fear of losing their jobs and livelihood. 3 Risk awareness, on the part of exposed workers and their employers, as well as knowledge and acceptance of available preventive solutions are necessary steps before installing adequate preventive measures, whether organizational, behavioral or environmental. Workers need to understand fully the hazards and risks in order to be able to make informed decisions under uncertain conditions.4 Prerequisites include the following: workers knowledge about the risk, their attitude towards it, which in turn, can be influenced by values, needs and interests. Also, knowledge and attitudes towards safety behaviour, organizational or environmental barriers must be taken into account. Our research focuses on these key elements, which help bridge the gap between health promotion research and practice. Methods A descriptive exploratory study is in progress with workers exposed to hand-arm vibrations. It uses qualitative methods that include focus group discussions with workers exposed to hand-arm vibrations, as well as individual interviews with other key informants (employers, health care professionals). An open-ended questionnaire was developed to collect qualitative data on perceived risks and solutions to prevent or reduce HAVS. Based on an integrated theoretical framework related to known determinants of behavior change, the analysis will focus on the following5: 1) knowledge of health effects, safety, well-being and/or quality of life 2) related beliefs about individual susceptibility and severity of consequences 3) attitude and values related to hand-arm vibration exposure 4) knowledge and attitudes towards exposure reduction, as well as perceptions of barriers and facilitating factors for these measures, in the workplace environment or otherwise.

Jan 6, 2006

By Michael J. Klishis

It was the goal of this project to develop training materials specific to two areas of the mining industry: (1) safe use and care of the self-contained self-rescuers, and (2) awareness and avoidance of electrical hazards. This report describes the development of the following training material: Instructor's modules for the OCENCO EBA 6.5, CSE AU-9A1, and PASS 700E self-contained self-rescuers; and a textbook, slide tapes, and accident case study scenarios for mine electricity, and a computer based instructional package on mine electricity and electrical hazards. The report concludes that additional efforts are needed in mine training and four recommendations are made: (a) tailor existing materials to fit specific mine sites, (b) develop and evaluate computer based instructional material, (c) develop parallel training materials for metal and non-metal mines and, (d) develop additional training materials for preparation plants and surface areas of underground mines.

Jan 1, 1985

By W. W. Weller

This report provides low-temperature heat-capacity data and entropies at 298.15° K. for magnesium metavanadate (MgV206) and magnesium pyrovanadate (Mg2V207). The work completes low-temperature measurements planned for alkaline-earth vanadates; an earlier report dealt with calcium vanadates.4 No similar data for these compounds have been published previously. Free energy of formation values at 298.15° K. were derived by combination of the present entropy values with heat of formation data. MATERIALS The materials used in the measurements were portions of the samples described in a previous Bureau of Mines publication by King, Koehler and Adami.5 Methods of preparation, chemical analyses, and X-ray examinations are covered in this paper. The indicated purity of the samples was 99.9 pct.

Jan 1, 1962

By Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to melt residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-offgas handling system, and thermal oxidizer for final offgas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 lb/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kV?A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the offgas and serves as an acid gas scrubber. The clean offgas is heated to 1,800° F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 2010

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By Nancy Estrada, Jane Nowell, Cathy Jennings, Debra Yniguez, Carol Lavery, Kristin Harrer

Pilots of the MH-60S helicopter are exposed to continuous whole body vibration (WBV). Pilot fatigue is a growing operational concern due to the increased frequency of extended durations of missions (6-8+hours) in support of Operations Iraqi Freedom and Enduring Freedom. Endurance aspects of the currently used rotary wing seating systems were not optimized for the longer missions and wide range of pilot anthropometric measurements, which is now typical of naval aviation. The current seating systems were designed primarily to meet crashworthiness requirements, not for the wide range of pilot anthropometry or to mitigate WBV. Albeit, an issue, pilot fatigue and reduced mission effectiveness are also critical concerns. Current Hazard Reports indicated that pain in pilots’ legs and backs begin two to four hours into the flight and increase with time. Mission readiness also decreases with an increase in flight duration due to the constant distraction of pilots shifting in their seats while trying to get comfortable. Froom, et al [2] reported a dose-response relationship between the length of military helicopter flights and back discomfort. He also concluded that this pain is typically dull, over the lower back, and its prevalence and intensity are dependent on the total flight hours of exposure. Methods This study evaluated WBV produced in the pilot seating systems onboard the MH-60S. The purpose of the study was to test and compare the effectiveness of two different seat cushions, the current seat cushion versus an anti-vibration seat cushion. Both seat cushions were measured for acceleration levels averaged over five-minute intervals using a triaxial seat pad accelerometer. The recordings were completed for a 3-hour straight and level flight. A frequency analysis from 0-80 hertz (Hz) was conducted on all acceleration measurements to determine the dominant axis and frequency of the pilots’ vibration exposure. The results were then compared to the applicable Threshold Limit Values (TLVs) established by the American Conference of Governmental Industrial Hygienists (ACGIH) [1] and the International Organization for Standardization (ISO) 2631.1 [3] to determine the MH-60S pilots’ permissible exposure time for both seat cushions. Results The results of the study showed that for both seat cushions the vibration levels of the z-axis at 16 Hz had the shortest allowable exposure duration, according to the ACGIH TLVs. In the z-axis at 16 Hz, the MH-60S’s current seat cushion’s acceleration levels indicated an exposure time limit of approximately 6 hours, while the anti-vibration seat cushion’s acceleration levels pierced the 8-hour exposure time limit curve. This is shown in the graph below.

Jan 6, 2006

In the USA, the National Institute for Occupational Safety and Health (NIOSH) does a lot of work and has provided news of interesting new developments. Marcia L. Harris describes an ?Explosibility Meter: ?In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. Federal [US] regulations require 65% and 80% incombustible content in samples taken in intake airways and return airways, respectively, assuming a nominal coal dust size of 20% minus 200 mesh. The Coal Dust Explosibility Meter (CDEM), a hand-held instrument developed by NIOSH uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture.? The CDEM is now commercially available. It provides real-time results during rock dust surveys instead of waiting weeks for laboratory results1. ?With real-time results, the potential for a disaster can be mitigated immediately. The CDEM displays the percent incombustible content as well as a colour indicating the relative explosibility of the coal and rock dust mixture. A red read-out indicates that more incombustible material is required to inert the coal and rock dust sample, while a green read-out indicates that the dust sample is sufficiently inert. When the mixture is marginally explosible, a yellow read-out is indicated. The red-yellow-green output depends upon the particle size distribution of the rock and coal dust mixture with the finer size fraction being more explosible.?

Jan 1, 2008

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By H. John Head, Fred N. Kissell

In This Chapter [Gas reports from around the world Regulations for gassy mines in the United States Differences between metal/nonmetal mines and coal mines Monitoring for methane and taking action Diluting methane with additional ventilation Eliminating ignition sources What experienced mine operators say about methane control and Looking for methane when starting a new mine or expanding an existing mine] This chapter gives guidelines for preventing methane gas explosions during metal and nonmetal mine development and subsequent production operations.3 Emphasis is placed on recognizing the differences between coal mines, where the potential for methane hazards is relatively well understood, and metal/nonmetal mines, where methane may accumulate unexpectedly. Also, interviews with experienced mine operators add much to a complete understanding of what must be done to address methane problems in metal/nonmetal mines. METHANE GAS IN METAL/NONMETAL MINES Gas reports from around the world. The presence of methane gas in metal/nonmetal mines around the world is more common than one might imagine [Edwards and Durucan 1991]. For example: • The former Soviet republics have occurrences of methane and hydrogen in apatite, gold, and diamond ores, where solid or liquid bitumen occurs in the rock. • Scandinavian iron ore deposits include methane and other hydrocarbons in boreholes that intersect pitch and asphalt within the deposits, and methane and nitrogen in boreholes and fissures in arsenic and sulfide ores.

Jan 6, 2006

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 2010

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1985. Shipments of processed tripoli increased slightly in quantity but decreased 6% in value, Production of garnet, an abundant iron-aluminum silicate, increased 24% in quantity and 20% in value. There was an 11% increase in the quantity and a 7% increase in the value of refined garnet shipped when compared with 1984 shipments, a new record high. Production of crude special silica stone decreased 10% in quantity and 14% in value, and shipments of finished special silica stone products decreased 85% in quantity and 68% in value. Both the quantity and value of special silica stone finished products sold or used were the lowest since 1981. Production of emery, an impure aluminum oxide, decreased 56% in quantity and 61 % in value of product mined and shipped. [ ]

Jan 1, 1987

By Fred N. Kissell

In This Chapter [Instruments available to measure methane in mines and tunnels Using a portable detector in both accessible and restricted spaces Machine-mounted monitors: placement and response time Calibration of catalytic detectors for different gases and Misinterpreting warning signs This chapter gives guidelines for methane measurement in mines and tunnels. The emphasis is on the measurement procedure and the interpretation of the measurement rather than on the instrument itself.] The failure to properly sample for methane is a major contributing factor to methane explosion risk. Sampling errors are most likely to occur at mines or tunnels where the presence of methane is not suspected or during nonroutine tasks at mines or tunnels known to have gas. More specific information on methane sampling at continuous miner sections is in Chapter 3. Chapters 4 and 5 discuss sampling at longwall sections, and Chapter 14 discusses sampling at tunnels. METHANE DETECTORS FOR MINING Many models of gas detectors are available to measure methane concentrations, as well as most of the other contaminant gases found in mines and tunnels. An example is the iTX Multi-Gas Monitor, a portable gas detector available from Industrial Scientific Corp., Oakdale, PA. This handheld instrument measures several gases simultaneously. The cost (2004) ranges from $1,300 to $2,200, depending on the number of gases measured. Similar instruments are available from other manufacturers. Most methane detectors used in mining use a catalytic heat of combustion sensor to detect methane and other combustible gases. These have been proven through many years of reliable operation. For detection of methane, proper operation of catalytic heat of combustion sensors

Jan 6, 2006

By R. P. Vinson

Assessment of workplace exposures is an important tool for helping to minimize dust-related occupational illness and diseases. Real-time particulate monitoring can effectively locate areas where dust controls are needed and determine how well they are working. An affordable, person-wearable, real-time dust monitor is needed. The SKC Inc. Dust Detective (SKCDD) fulfills those requirements (Disclaimer: Mention of any company or product does not imply endorsement by NIOSH). The SKCDD consists of a disposable sampling tube (DST) connected to a small hand-held sampling pump. The SKCDD was developed through a Cooperative Research and Development Agreement (CRADA) between the National Institute of Occupational Safety and Health (NIOSH) and SKC Inc. The relationship of dust concentrations measured by personal gravimetric samplers to those measured by the SKCDD was determined in a laboratory aerosol chamber. A comparison of the means and the relative standard deviation of triplicate measurements of each type of sampling device demonstrated the SKCDD to be a viable alternative means for measuring dust. While it provides accurate measurements for specific coal types, it requires correction factors (those correction factors still need to be calculated) for other coal types.

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By Ronald B. Hollenbeck

The value of mineral production in Alabama continued to increase and reached a new high of $260 million, 3 percent above the previous high established in 1967. Record high values were reported for bentonite, crushed marble, lime, miscellaneous clay, portland cement, salt, sand and gravel, and scrap mica. The value of coal, total cement, petroleum, and stone accounted for 87 percent of the State's total value of mineral production. Alabama ranked second among the States in the production of bauxite and scrap mica and third in kaolin, masonry cement, and native asphalt.

Jan 1, 1970