Search Documents

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

By Ted C. Briggs

A removable-jacket distortion apparatus was constructed and used to measure distortion coefficients for two high-pressure vessels. The measured distortion coefficients were used to compute distortion coefficients for volumes VI and (V1+V2) of a 1,000-atmosphere Burnett compressibility apparatus for the temperature range 0° to 75° C. Young?s modulus for Armco 17-4 PH stainless steel, heat treated to condition H1150-M, was computed from experimentally determined distortion coefficients. A 10-to 14-percent correction to the values obtained for Young's modulus may be required because pressure vessel end effects were neglected. The distortion coefficients of the compressibility apparatus are believed to be accurate to about 1 percent.

Jan 1, 1970

By Thomas M. Barczak

Roof support technology for longwall tailgates has changed dramatically during the past decade. Filling tailgates with conventional wood cribs is becoming the exception rather than the rule. Modern engineered timber support systems and a host of other alternative support products provide far greater capacity as well as stiffer response, thereby allowing the supports to resist roof movement with much less displacement than the soft wood cribbing used in the past. For these reasons, these products can provide superior roof control. In addition, the material handling requirements for support installation have now become a major consideration in the support design and selection process. Products such as conventional wood cribbing that require piece-meal construction of bulky, heavy components have diminished, while prop-type supports and products that can be installed with machinery and pumpable support technologies have grown in use resulting in fewer injuries to mine workers. Now, the opportunity exists to provide the safest, most cost effective support system, through engineering design rather than by trial and error and to optimize the use of the support system chosen. Yet this is rarely done. The key to accomplishing this task is to understand the interaction of the support system with the ground conditions at the installation site. A major focus of the paper is to conceptualize the support and interaction through the use of a ground reaction curve which relates the support resistance to the convergence of the longwall tailgate. The goal of any roof support design is to control the ground deformations and maintain the structural integrity of damaged or broken ground to the extent possible to provide a stable mine opening. In general, deformations will be a function of the stress environment and inherent strength of the surrounding rock mass. However, if the deformations are intimately linked to the stress changes such that the deformation can be controlled by the load resistance or reinforcement provided by a roof support system, then the loading behavior can be described as load-controlled. Conversely, if the deformation occurs irrespective of the installed support (assuming practical limitations), then the loading behavior is described as displacement-controlled. In this case, the deformation can be considered irresistible from a practical standpoint. In this context, the nature of the loading has significant consequences on the support design requirements. Finally, examples using the NIOSH Support Technology Optimization Program (STOP) to develop design criteria using ground reaction data from underground studies and ways to include uncontrolled convergence as part of the design criteria for standing roof supports will also be discussed.

By T. M. Ruff

The U.S. Bureau of Mines has developed a portable, inexpensive teleoperation system for mobile hard-rock mining equipment. The system was tested on a compact loader-trammer in a simulated stope. The teleoperation system includes radio remote control and computer-assisted navigation. A recent enhancement includes video cameras mounted on the machine to provide visual information to the operator. This system allows the operator to remain in a safe location while operating the machine from a distance, thus increasing both operator safety and mining productivity.

Jan 1, 2010

By E. J. Murphy

"INTRODUCTION This investigation is a continuation of previous work 3/4/5/ on the gaseous products of permissible explosives with and without sheaths. The range of oxygen balance of the explosives has been considerably increased. As has been shown previously, certain approximate relations exist between the volumes of gaseous products and the oxygen balance. Further systematization of the data is not feasible, since the method of theoretioal calculatln of the gaseous product is not yet satisfactorily developed. In a previously described method, 6/ it has been assumed that the explosion occurs at constant volume and that thermodynamic equilibrium is established. Apart from the presumably less important uncertainty of some of the thermodynamic data, it is not known how the confinement of the shots in the Bichel gage or the Crawshaw-Jones gage should be treated, or whether thermodynamic equilibrium is fully attained; nor can the extent to which the equilibrium composition changes during the subsequent period of expansion and cooling be judged with any reliability. Therefore, no calculations have been attempted. However, in anticipation of possible future theoretical interest and as an aid in answering practical problems, the new data are presented in the same minute detail as was done previously."

Mar 1, 1948

Objective: To help prevent squeezes, collapses, and other pillar failures through better pillar design, thereby enhancing safety for underground mine workers.

Jul 1, 1997

By S. J. Broderick

[The authors gratefully acknowledge the assistance of O. C. Ralston, chief engineer, Nonmetals Division, Bureau of Mines, Who suggested the problem and Gave valuable aid during the course of the work. Thanks axe due also to Will H. Coghill, supervising engineer of the Southern Experiment Station, Bureau of Mines. INTRODUCTION One phase of the general program for utilization of coal-mine waste led to the possibility of making a water softener from the material, as the waste matter contained both coal and clay and. it is known that both these substances can be so activated as to exhibit distinct base-exchange properties. The carbonaceous]

Jan 1, 1941

By S. J. Broderick

[One phase of the general program for utilization of coal-mine waste led to the possibility of making a water softener from the material, as the waste matter contained both coal and clay and it is known that both these substances can be so activated as to exhibit distinct base-exchange properties. The carbonaceous]

Jan 1, 1941

By G. M. Potter

During the investigation of the occurrence of manganese deposits in the western United States, examining engineers of the Bureau of Mines collected samples from four properties in Siskiyou and Mendocino Counties northern California. As the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were made between 1941 and 1945 to determine the amenability of the ores to concentration. The Johnson and Reynolds properties are near Fort Jones Siskiyou County. The ore occurs in a number of small lenses in that area. Samples were taken for testing for amenability to treatment in a small custom-gravity plant, tentatively planned. by the Waiter Johnson interests of San Francisco. A 2-ton representative sample was obtained from numerous exposed portions of an outcrop on the property of the Mayland Mining Co. The Mayland mine is about 8 miles from Sawyers Bar in Siskiyou County. The ore body consists of stringers and irregular masses of oxide, and. silicate ore scattered through quartz, which these minerals have replaced.

Jan 1, 1952

By John Dasher

The impetus given to mineral dressing arid chemical engineering by the war has placed many persons without previous experience in positions where they are concerned with the size of solid materials they are testing. Many good textbooks cover this field in considerable detail but are more concerned with the "why" than with the "how" For beginners and those to whom size is not of primary concern, this brief circular has been prepared. Refer-

Jan 1, 1942

By D. P. Desmond

The U.S. Bureau of Mines investigated leaching automobile catalysts with sodium cyanide (NaCN) solutions at high temperatures to recover platinum-group metals (PGM). The feed was virgin monolith rejects, used monolith, and used pellet catalysts. Leaching with a 5-pct NaCN solution for 1 h at 160° C dissolved over 97 pct of the PGM in the virgin monolith, over 85 pct of the PGM in the used monolith, and over 90 pct of the PGM in the used pellet catalyst. Over 99.8 pct of the dissolved PGM was recovered as a precipitate by heating the solution to 250° C for 1 h in an autoclave. The cyanide complexes were decomposed, and free cyanide was destroyed.

Jan 1, 2010

By S. L. May

Investigations by the Federal Bureau of Mines indicate that hafnium and zirconium compounds of acceptable purity can be extracted from Nigerian zircon concentrates. Chlorination and caustic soda fusion techniques were used to extract 85 to 95 percent of the valuable metals from the concentrate. The extracted hafnium and zirconium compounds were purified by recrystallization of the oxychlorides or by formation of complex salts during chlorination. The zirconium-hafnium product of the recrystallization method contained 15 parts per million of uranium, and the product of the salt-complex method contained less than 10 parts per million of uranium. The hafnium was separated from zirconium by solvent extraction methods. A zirconium product containing 0.3 percent hafnium and a hafnium product containing 4 percent zirconium were obtained. At the request of the Atomic Energy Commission (AEC), work was started to develop techniques for processing Nigerian zircon concentrates in commercial installations presently engaged in producing zirconium and hafnium metals from ores. The Nigerian zircon has a high hafnium content, but the presence of uranium and thorium is a problem not normally encountered in processing zircon concentrates.

Jan 1, 1961

The Production Profile Program is written for use on a Digital Model PDP 11/70 computer using a Fortran IV level G language. It may be run on any system which uses G level or an upward compatible version of Fortran IV language. Please note, however, that the Model PDP 11/70 for which the program was written is programed to read DEC026 type keypunching. If the user's computer is programed for another type of keypunching it may be necessary to re-keypunch the Production Profile Program. The Production Profile Program uses a fourteen card input. The data must be keypunched according to the layout described in detail in the multiple card layout forms (following). The output from this program must be printed on wide paper, as a full 120 columns are used. The samples of output at the back of this appendix have been reduced for inclusion in this report.

Jan 1, 1977

By W. W. Odell

The results of the 1921 cooperative experiments conducted by the U. S. Bureau of Mines and the University of North Dakota at the University mining substation plent at Hebron , North Dakota , pointed clearly to certain definite dep ficiencies in the schemes hitherto developed for benefiting and utilizing lignite . First The apparatus used in the carbonizing process or used to produce carbonized lignite suitable for briquetting is too costly , that is , the cost per ton day of residue made is too high . Second - The depreciation of the carbonizing appara tus is too high . Third The carbonizing apparatus can not be operated intermittently without seriously damaging it and impairing its efficiency of performance . Fourth Too little attention has been given to the possibility of using at least a certain percentage of the carbonized lignite directly in suitable stoves and furnaces without briquetting or other treatment . Accordingly , consideration was given to the design of an oven that could be built at a mine without the importation of highly skilled and specially trained construction men , erected at a low first cost , readily kept in a state of repair , operated at a rela tively high capacity and put into operation or shut down at will without seriously damaging the brickwork . The need of such an oven was appreciated also by the University of North Dakota and a cooperative agreement was made to build and operate such an oven during the summer of 1921.

Feb 1, 1923

By G. David Baskin

Changes in the 1978 quantity and value of the sales of various natural abrasives, compared with the data for 1977, were of a mixed nature. Output of tripoli-type materials and garnet increased in both tonnage and value. Emery production also increased. But special silica stone product sales decreased in both tonnage and value, and the reported quantity and value of sales of manufactured abrasive material also decreased for 1978. In 1979 output of tripoli-type materials and special silica stone products decreased in both tonnage and value when compared with the previous year. The tonnage and value of sales of garnet and manufactured abrasives increased when compared to 1978 data.

Jan 1, 1980

By Lloyd R. Michels, Burke Cartwright, S. F. Ravitz

"INTRODUCTION Frequent attempts have be,made in the electrolysis of molten magnesium chloride to regenerate the electrolyte by allowing the chlorice generated at the anwdo to read with magnesium oxide and carbon within the melt according to the following reactions: (1) MgO + C + CL2 = MgCl2 + CO,(2) 2MgO + C + 2C12 = 2MgC12. + CO2.The principal advantages of such a procedure are that (1) the direct source of magnesium is magnesium oxide rather than the more expensive dehydrated magnesium chloride and (2) it is not necessary to handle or dispose of large quantities of chlorine or hydogen chloride.Grätzll 5/ proposed the use of an MgO carbon feed in a more or,less compact form in the anode compartment, of the cell. In a patent issued to Magall Aktiengecellschaft, 6/ a compact mixture of MgO and carbon is used as the anode itself. Kato 7/ and Backer 8/ add the feed in finely divided form to the surface of the anode compartment. The Bureau of Mines 2/ recently made a pilot-plant investigation of the electrolysis of suspension of MgO and carbon from chloride melts, in which it was found that although,current efficiencies of 60 to 70 percent were obtainable, the formation of sludges containing MgO, carbon, and magnesium seriously interfered with the operation of the cell,"

Apr 1, 1945

By Edward L. McHugh, Stanley M. Miller, Jeffrey K. Whyatt

The point estimation method can be applied to the safety factor (SF) equation for any specified rock slope failure mode (such as plane shear, step path, or wedge) to obtain reliable estimates of the mean and standard deviation of the SF probability distribution. A gamma probability density function is recommended for modeling this probability distribution, because it allows only for positive values and is flexible enough to provide symmetrical shapes and right-skewed, exponential-type shapes for the SF distribution. The mean and standard deviation define this distribution, which then can be integrated numerically from 0 to 1 to obtain the probability of sliding, PS (portion of the SF distribution where SF < 1.0). The overall probability of failure, PF, for the potential slope failure mass is the joint probability that the rock discontinuities are long enough to allow kinematic failure (PL) and that sliding occurs along the rock discontinuities (PS); that is, PF = PSPL. This method for estimating the probability of sliding is extremely efficient computationally, and thus, expedites slope stability simulation routines used by NIOSH software to stochastically describe rock slope behavior and assist the engineer in designing catch benches for large rock slopes. Enhanced bench design translates into increased operational efficiency and safer working conditions in open pit mines and quarries.

By Fred N. Kissell, Jerry C. J. Tien, Edward D. Thimons

At coal mine working faces, simultaneous application of three basic elements reduces the methane explosion hazard: (1) adequate ventilation, (2) regular monitoring of gas concentrations, and (3) the elimination of ignition sources. This paper reviews the application of these elements in a manner relevant to Chinese coal mines. Adequate ventilation is provided by using the mine entries to convey air for the long distances between the mine portal and the working sections (main ventilation systems) and then using line brattice or ventilation duct (face ventilation systems) to convey air the last hundred meters to the working face where coal is broken and removed. The air quantity provided is enough to safely dilute methane and the air velocity is enough to prevent layering. Gas concentrations are regularly monitored in accordance with regulations using knowledge of the circumstances under which the highest concentrations are likely to be found. Ignition sources are eliminated by ensuring that electrical equipment does not ignite methane, that sparking from cutter picks is minimized, and that smoking by workers is strictly forbidden. Risk-reduction studies using fault-tree analysis have shown that large reductions in explosion risk only result from multiple preventive actions. For example, a ventilation upgrade or a methane monitor upgrade by itself offers risk reductions under 50 pct. A risk reduction of 90 pct. or more would typically require much more. Other studies have shown that the everyday vigilance of those working underground is as important as engineering design.

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

By S. S. Peng

Successful longwall mining requires a good roof control. A good roof control implies that: (1) no excessive pressure is build up in the face powered supports, and (2) chain pillars are designed in such a way that panel entries are well protected and interactions between adjacent panels are minimized. A clear understanding of strata behavior around longwall panels due to face movement is, therefore, the foremost requirement for achieving better roof control. This dissertation is designed to analyze the effects of strata behavior on longwall panels due to the mining activities. The following topics are studied: (1) the weighting, phenomena and their effects on front abutments, and (2) the chain pillar stability and pillar design under various roof conditions. Three dimensional finite element analysis was employed. The effect of parameters such as overburden depth, mechanical properties of the immediate roof and main roof, panel width, and size of chain pillar on (t) and (2) were analyzed. Four typical models were utilized to simulate various phases of panel extraction under various combinations of the above parameters; model one is to simulate the beginning of panel mining; model two is to simulate the situation that longwall face has passed more than half of panel length; model three is to simulate the completion of panel production; and model four is to simulate the second panel mining. The following formulae have been developed by applying multiple regression model to analyze the finite clement results: (1) a formula that classifies the type of root strata at the face area. (2) formulae that predict the first weighting and periodic weighting lengths. (3) a formula for design of the chain pillar size. Case studies were performed to check the validity of the formulae proposed. Comparison of the formulae proposed for the chain pillar design with other formulae were also performed.

Jan 1, 1984