Search Documents

By Oscar Lee, B. W. Gandrud, F. D. DeVaney

"IntroductionFlue dust which results from the smelting of ores containing appreciable quantities of fines is one of the troublesome products of iron blast-furnace practice. Gases issuing from the furnaces at a high velocity carry small particles of coke, ore and flux into dust-collecting chambers. These particles constitute the flue dust. Lasses of iron ore through the production of flue dust vary between wide limits in the different furnaces, and depend on a number of factors, such as size and design of furnace, amount of fines in the ore, the operating conditions and the blast pressure.Blast-furnace operators of the Birmingham district keenly realize this waste. The ores are comparatively low grade and require more fuel than is ordinarily used elsewhere. Hence the flue dust is low in iron content and high in coke. As a result it is not in suitable condition for direct sintering. In many other iron and steel centers direct sintering is a common practice. In the Birmingham district efforts have been made to prevent this loss by recharging the dust into the furnace, but, as might be expected, a material fine enough to be blown out once will very likely be carried over again.In general, the flue-dust losses in this district will average 250 pounds per ton of pig iron produced, but at times the losses at different furnaces are substantially higher or lower than this figure. On the basis of the present rate of pig-iron production, the annual loss of flue dust exceeds 300,000 tons. The iron content of the dust probably averages 25 per cent, therefore about 75,000 tons of iron is wasted yearly, or about 3 per cent of the iron mined is lost in flue dust."

Jul 1, 1926

By J. F. McCoy

As mining develops into deeper and hotter regions, the safety and health of miners require that the workspace be cooled. Toward this end, this program has successfully developed a high performance, low maintenance spray cooler of 5000 cfm nominal capacity. Further, a series of four 25,000 cfm, nominal capacity, spray coolers has been built and mine tested with satisfactory results. The smaller coolers have been patented and become commercialized with 50 units currently in service. The concept has been developed independently overseas with an unknown number of units in operation.

Jan 1, 1984

By C. E. Jordan

The Bureau of Mines is conducting research into the pneumatic recovery of coarse mica and has used this method to produce mica concentrates that contain more than 90 percent mica. This research is being carried out pursuant to the Bureau's objective to develop technology that will help maintain an adequate supply of minerals and metals to meet national economic and strategic needs. Researchers used a Bureau-designed system of crushers, screens, and zig-zag air classifiers to concentrate coarse liberated mica particles from mica-bearing materials. This pneumatic system was used to concentrate four mica ores from Arizona, North Carolina, and South Dakota and three waste tailings from Alabama, Georgia, and South Dakota. Using these samples, it was demonstrated that plus 65-mesh size mica can be effectively recovered by the pneumatic method. Not only were the concentrates high in mica content; it was also demonstrated that this method can be used to recover up to 78 percent of the mica that was originally contained in the samples. Because it is a dry concentration method, the pneumatic beneficiation technique may be advantageous in areas where water resources are limited.

Jan 1, 1980

By Jennifer S. Riefenberg

The U.S. Bureau of Mines conducts basic and applied research related to predicting, eliminating, and/or controlling rock bursts in underground hard-rock mines and coal bumps in underground coal mines. An important element in this research is the development of a reliable and efficient microseismic source location technique. This report presents the results of a Bureau study to develop and evaluate a new algorithm to locate microseismic events based on the Simplex method, a powerful linear programming technique. The technique was tested on both field data and simulated data. Microseismic event source locations obtained with this new Simplex-based algorithm were shown to have less error than those locations obtained using a least squares method. It was concluded that the Simplex approach to source location of microseismic events can be used effectively in microseismic monitoring.

Jan 1, 1989

By C. R. Nisewanger, F. W. Brown

"The velocity of detonation of an explosive is one of its most important properties, because its performance depends markedly on the rate at which it releases its energy. Fortunately, the velocity of detonation is one of the few properties of an explosive that can be measured precisely. However, the velocity of detonation of an explosive may depend on several factors other than its chemical composition, such as density, physical state, degree of confinement, nature of confinement, and magnitude of initiating impulse. Presumably for an explosive of fixed chemical and physical properties there are certain limiting conditions of confinement and initiation under which the explosive will detonate at a maximum constant and uniform velocity. This velocity is its ""ideal"" velocity of detonation. It is obvious, however, that in order to evaluate performance properties of an explosive in all of its applications it may be necessary to measure its velocity of detonation under a number of conditions in which the velocity of detonation is far from the maximum ""ideal"" velocity.. Under certain-conditions the velocity of detonation may even,be,different at different points in the explosive.It is .relatively simple to determine the velocity of detonation of an explosive under a. standard set of conditions if one is free to use large quantities of the explosive and to form it into a convenient shape. Under these circumstances; one can use a thin column of explosive a meter or more in length. The time required for an explosion to travel the length of the column will not be less,of the order a few ten-thousandths of a second and can be readily and accurately measured .by means of the standard spark chronograph or by photographing the explosion with a rotating-drum camera. However in many applications the explosive charge may be of relatively small dimensions arid may not be in a form convenient for making velocity measurements and often may be enclosed in a case or other confining medium. It may be necessary to determine the velocity of detonation over distances of the order of a few centimeters, in which case the time intervals to be measured will be extremely small. For example, the time required for an explosion to traverse 1 centimeter of tetryl is of the order of 1.5 microseconds.Since no satisfactory method of determining time intervals of the order of magnitude of a few microseconds within an explosive charge was available,, at least not for all conditions that might be encountered in practice, it was necessary to develop a special electronic chronoscope which is capable of measuring time intervals as small as a microsecond with a fair degree of accuracy. This report describes the chronoscope and its application to measurements of velocities of detonation in explosives."

Mar 1, 1946

By G. L. Oldright

"The various districts in the United States where complex lead-zinc ores occur are too well known to require description, there being hardly a mining State with any large amount of ores of either metal that is free from this problem. This paper briefly presents developments in the volatilization process, as applied to the treatment of such ores, since the data in Bureau of Mines Bulletin 211** were published. In that bulletin, among the many types of ore treated, examples are given of the treatment of lead-zinc ores by the chloride volatilization process for the separation of lead. An outline of the general process, with views of the rotary kiln, ore feeder, firing system (these three features resemble closely those of cement-kiln practice), dust chambers, and a Cottrell precipitator to remove the fume from the gas, are also shown in that bulletin, to which the reader is referred for the results obtained, and for practical details of operation. The small initial cost of a volatilization plant, and its adaptability for use in isolated districts were emphasized.In general, it was found that when an intensely oxidizing atmosphere was maintained in the furnace, a good lead-zinc separation could be made. Therefore, a heavy sulphide ore would have to be preroasted, and enough air would have to be admitted to obtain complete combustion of whatever fuel might be used.The work done by private companies and the bureau since the data for Bulletin 211 were obtained, indicates that the ores most immediately amenable to treatment by volatilization are of two types. The first is an oxidzed lead. silrer ore whose variable lime content makes it impractical to chloridize the ore for acidulated brine leaching, and whose base metal content makes treatment by cyanidattion unfeasible, The second type is the lead-zinc ore mentioned above, and is the one on which data are available for publication at present. This article Chows what ores of this latter type are amenable to treatment by volatilization, by giving briefly some of the more important physical and chemical properties an ore should preferably possess. Several examples are given from both laboratory experimental work, and from practice in the field, showing various phases of the volatilization process."

Nov 1, 1923

By Thomas Brunsing

The program was carried out to develop deep kerfing and core breaking techniques to be incorporated into the design of a field prototype hard rock mining machine. The field machine is designed to mine non-abrasive bedded deposits up to 20,000 psi in uniaxial compressive strength. The mining technique involves cutting approximately 2 ft deep parallel kerfs spaced 2 ft apart in either a horizontal or vertical direction and subsequently breaking out the cores so defined. The prototype machine is intended for demonstration of the technique in a quarry or equivalent field environment. The program was aimed at minimizing the required kerf width, obtaining reliable breaking within that kerf width and determining cutter blade requirements necessary to achieve a mining rate of 20 ft3/min. Full scale breaking experiments and 1/2 scale kerfing experiments were employed to evaluate the system. High strength concrete test specimens were used to simulate the rock being cut and broken. The test results indicate the kerf/break technique can achieve the desired mining rate by utilizing two 7 ft diam blades to cut 2 in. wide by 24 in. deep kerfs. A lateral load applied at the base of the kerf (base shear) was selected at the core breaking technique to be employed by the full-scale prototype machine.

Jan 1, 1983

By A. F. Baker

Laboratory flotation of synthetic coal-pyrite mixtures and high-pyritic-sulfur coal indicated that ferric chloride (FeCl3), aluminum chloride (AIC13), chromium chloride (CrCl3), and cupric sulfate (CuSO4) are potential pyrite depressants. For each metal salt there appeared to be a range of pH values and optimum concentration for selectively depressing pyrite in coal flotation. Pyrite was depressed in the pH range from 4.5 to 7.0 with ferric chloride, from 5.8 to 7.0 with aluminum chloride, from 6.4 to 7.1 with chromium chloride, and from 6.4 to 7.4 with cupric sulfate. Best separation of pyrite from coal was achieved in flotation solutions containing from 2 X 10-5 to 5 x 10-5 mole/ liter of each salt. In solutions containing excess salt concentrations, coal was also depressed. These Bureau of Mines tests demonstrated on a laboratory scale that, in solutions containing 4 X 10-5 mole/liter ferric chloride and from 1 x 10-4 to 2 x 10-4 mole/liter sodium hydroxide, the pyritic sulfur content of a Lower Freeport bed coal sample could be reduced from about 2.51 percent to less than 0.60 percent with recoveries of over 83 percent. The depression of pyrite appears to be due to the adsorption of positively charged colloidal metal hydroxide at the pyrite-solution interface. This hypothesis is supported by zeta potential determinations which showed that suspended coal and pyrite particles in solutions containing metal salts are positively charged in the pH range where depression occurs.

Jan 1, 1971

By Robert R. Perron

The U. S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 15 to 30 ampere fault to ground, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1975

By Loren R. Anderson

This Volume documents the use of the Cone Penetrometer data analysis computer programs VERT and HORZ. The programs are interactive in that they prompt the user for input data and allow correction and modification to be made. The programs read data from the results of cone penetrometer soundings and convert the data to values of tan ø. Mean, standard deviation, skew, kurtosis, linear trends and autocorralation are computed by the programs.

Jan 1, 1982

By T. M. Barczak

This U.S. Bureau of Mines report investigates shield mechanics and component stress development in a two-legged longwall shield for unsymmetric canopy and base contact configurations. Previous studies analyzed shield behavior for symmetric contact configurations. The goals of these efforts are to improve longwall support selection and design. This study provides vital information that will help develop improved procedures for performance testing of longwall supports and will benefit future research to improve support design through stress optimization and evaluation of failure mechanisms. Combinations of six canopy (three symmetric and three unsymmetric) and six base (four symmetric and two unsymmetric) contacts provided a total of 36 configurations for evaluation. Of these 36 configurations, 10 were eliminated because of fixture limitations or shield instability. Controlled vertical and horizontal displacements were applied by the Bureau's mine roof simulator to the remaining 26 configurations. Component responses were determined from pressure transducer and strain gage instrumentation in order to identify contact configurations and boundary displacements that produced maximum loading in each of the support components. This report describes these test results and provides conclusions relevant to critical contact configurations for performance testing of longwall supports.

Jan 1, 1990

By Jr. Hazen

This report documents 653 sets of sample data involving 78,366 assays obtained from past exploration for various minerals and metals. Most of these data have been taken from published reports describing exploration projects, conducted jointly by the Bureau of Mines and the Geological Survey, for the Strategic Minerals Program from 1940 through 1949. Means and standard deviations have been computed for the exploration assay data and have been plotted on graphs for 22 minerals and metals. A mathematical model, based on the binomial distribution, has been developed to explain the configuration of the plots of the exploration means and standard deviations. The two statistics, mean and standard deviation, which describe assay data, have been used for simulating probability models. These probability models then have been combined with the binomial model of the exploration assays and related to the sequential decision process associated with exploration drilling for mineral deposits. These probability regions can be used to form the basis for sequentially predicting the probable range of the average grade of mineral or metal that may be expected as an exploration drilling program is continued after the initial discovery of mineralization has been made.

Jan 1, 1966

By E. H. Denny

This paper discusses accident experience and costs in 150 Colorado coal mines for the 5 years 1929-33; these mines produced 62 percent of Colorado's coal tonnage during this period. This and similar studies by the United states Bureau of Mines in other States (listed in the appendix to this report) make available comparable information on mine-accident costs and bring out clearly the importance of accident reduction from the humanitarian as well as from the economic standpoint. Compensation insurance costs constitute a considerable part of the cost of coal output. The tendency toward greater liberalization of workmen's compensation laws and increased benefits thereunder may mitigate to some extent the seriousness of an accident to a worker and his dependents, but no compensation is paid ultimately, not by an insurance fund but by the mine operator and the general public, which includes the miner. The one really effective method of reducing compensation costs is to reduce the number and severity of accidents.

Jan 1, 1935

By R. V. Ramani

This report is volume 1 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report contains a statement of the purpose and scope of work of the Grant, and provides an overview of the Master Design Simulator with a brief description of each subsystem. Also included is a discussion of several areas of application for the simulator.

Jan 1, 1975

By R. T. MacMillan

A number of chemical techniques have been applied to manganese ores from three areas of Aroostook County, Maine. Although large tonnages of these ores have been proved, they are low grade, and their exploitation has awaited a suitable beneficiation scheme. As conventional ore-dressing methods had failed to yield satisfactory results, attention was turned to chemical procedures. Leaching with dilute (7-percent) H2S04 extracted over 90 percent of the manganese from ore of the Dudley farm area, consuming 3.8 pounds of acid per pound of manganese extracted. Ores from the Littleton Ridge and Maple Mountain-Hovey Mountain areas were less amenable to this treatment, yielding approximately 80 and 60 percent of their Mn content, respectively. To increase the percentage extraction of manganese in the latter two ores, a number of factors were varied, including (1) acid concentration in the extracting solution, (2) ratio of acid to Mn in the slurry, and (3) preliminary heat treatment of the ore with a reducing agent. Other acids, including HNO3, HC1, and H2SO3, were tried also; however, no significant improvements in the Mn leached from Maple Mountain-Hovey Mountain ore were made. The manganese extraction of Littleton Ridge ore was raised to 90 percent by providing 9 to 11 pounds of HNO3 per pound of Mn in the ore.

Jan 1, 1954

By C. D. Litton

This Bureau of Mines report presents a set of guidelines for determining the distribution of product-of-combustion fire sensors in underground mines. Sensor spacing is defined in terms of sensor alarm threshold, ventilation flow rate, and mine entry dimensions. Sensor spacing guidelines are presented for detection of fires from two primary combustibles, coal and wood, which are common to the majority of underground mines. The guidelines are based on data from full-scale and intermediate-scale fire tests conducted by the Bureau of Mines.

Jan 1, 1983

By L. N. Plein, J. W. Paul

"The United States Bureau of Mines, in the interest of the prevention of injuries and fatalities in coal mines, has engaged in a study of the circumstances and conditions under which falls of roof and coal contribute to coal-mine accidents, and this publication is devoted to the result of a study conducted in mince developed in the Pittsburgh or No. 8 coal in eastern Ohio.To emphasize the need of this study a statement of the fatalities which have resulted from falls of roof is presented, followed by a brief description of the field and its geology. The mining methods, regulations, and timbering practices are presented and discuss, as well as supervision and discipline, all of which are important factors in the control of the roof and the prevention of falls of roof material that are liable to result in injury to the underground workmen.During the five-year period, 1924 to 1928, there were 10,820 fatalities in the cool mines of the United States, of which number 5,573 or 51.5 per cent resulted from fells of roof material, such as draw slate or roof coal, and of coal from the fact or sides. These fatalities generally occur singly, consequently they are given little publicity compared with major disasters consulting from explosions which, during the same five-year period, amounted to only 17.8 per cent of the total fatalities.Seven,mines in eastern Ohio, each typical, of mines in its locality, have been carefully studied, and the result of this study is herein presented so the information may be and beneficial to all who may be operating mines having,similar natural or physical conditions.In general, it will be found that measures taken to prevent injuries or fatalities from falls of roof as well as other safety measures, will have the effect of increasing the efficiency and economy in mining operation. The result of the study so far made on the falls of roof problem indicates that such features as mine management, supervision, inspection, discipline, character of roof, timbering methods, and blasting have a direct bearing on any scheme that may be evolved to prevent injury or loss of life by falls of roof."

Mar 1, 1931

By Martin Hertzberg

The early and reliable detection of the self-heating of combustible substances in mines is of considerable importance to the mining community. This Bureau of Mines report describes the results of a variety of studies of incipient combustion and its detection. Heated samples of coal, wood, and various polymers were used to evaluate the relative sensitivities of several types of detectors. The laboratory results indicate that submicrometer particulate detection is the most universal and sensitive method. Carbon monoxide detection was as sensitive as submicrometer particulate detection for pyrolyzing coal but was relatively insensitive to pyrolyzing wood or plastics. The conventional type of ionization smoke detector was the least sensitive for coal and of intermediate sensitivity for wood and plastics. Self-heating experiments with Pittsburgh seam coal piles of varying particle sizes gave ignition temperatures of 170° C for 4-to 7-µm dust, which increased monotonically with particle size. The measured heating rates were compared with data from an adiabatic calorimeter to obtain preexponential rate constants. The preexponential rate constants varied linearly with the surface area per unit mass of sample as would be expected for heterogeneous surface oxidation. The propagation behavior of ignition waves and the overall self-heating appears to depend critically on the magnitude of the convective flows induced, which counteract the depletion of oxygen in the void spaces of the pile. Classical theories of thermal ignition require substantial modification to be applied reliably to such cases.

Jan 1, 1977

By D. L. Forrester

This paper, describing the milling practice of the Old Dominion Co., is one of a series being prepared by the: United Staten Bureau of Mines. ACKNOWLEDGMENT In the preparation f this paper, acknowledgment is made of the valuable service rendered by R. S. Allen, metallurgist of the Old Dominion Co. T. G. Chapman, one f the consulting engineers of the Bureau of Mines, assisted in arranging the paper for publication.

Jan 1, 1931

By G. M. Potter

During investigation of the occurrence of manganese deposits in the western United States, the Bureau of Mines collected 2-ton samples of 4 ores from 3 properties in northeastern Nevada. Laboratory tests were made to determine the amenability of these ores to ore-dressing methods of concentration. The Caviglia-Vietti property is situated 11 miles southeast of Ely, White Pine County, Nev. The ore deposits are lenticular veins and irregular masses found in limestone fracture zones and along the contact of limestone and underlying shale. Two samples, of the ore were tested: Lot A, from the Vietti shaft, and lot B, from the. Caviglia shaft.

Jan 1, 1954