Search Documents

By M. L. Glenn

The Bureau of Mines is conducting research on substitutes for chromium-containing alloys in order to conserve imported critical and strategic materials. Part of this research concentrates on finding low-chromium substitutes for heat-resisting stainless steels for the temperature range 600° to 800° C. Ferritic alloys are emphasized that have oxidation resistance provided by chromium contents as low as 10 pct and stress rupture strength provided by the precipitation of the chi(X)-phase intermetallic compound, (Fe36Cr12 (Mo, Ti)10). Initially, research was concentrated on selecting an alloy composition having a minimum chromium content with strengthening provided by the X-phase. An Fe-(10-12 pct)Cr-6 pct Mo-(1.5-2.0 pct)Ti alloy was selected. After the alloy selection, the tensile, stress rupture, and oxidation properties were determined. Stress rupture properties were found to be similar to those of 304 stainless steel. However, the alloys possessed brittleness during both stress rupture and tensile testing, possibly as a result of too high a content of molybdenum and titanium. Higher than expected oxidation rates were found that may be caused by the high molybdenum content.

Jan 1, 1984

By Peter W. Kauffman

This Bureau of Mines publication is designed primarily to provide mine engineers and production-level mine managers with the following: 1. Information to assist them in making the decision to retreat mine and in selecting the best retreat mining technique for specific mining conditions. 2. Information on mine planning that will enable them to design mine layouts for safe and efficient retreat mining. 3. Information that will enable them to develop a section foreman's handbook. The manual has been organized to gradually increase in level of detail as the reader progresses from beginning to end. Individuals interested in an overview of retreat mining can confine themselves to the first few chapters. Those interested in mine planning, should read the middle chapters as well. Those interested in the development of a foreman's handbook should read the entire manual.

Jan 1, 1981

Bosworth, T. 0. The Mackenzie oilfield of northern Canada. Petroleum Times, vol. 5, Apr. 30, 1921, pp. 489-491. Jour. Inst. Petroleum Technologists, vol. 7, Oct., 1921, pp. 276-290; discussion, pp. 290-297. Gives location of the field, some of its geology, mode of occurrence and character of the oil. See also Oil Trade Jour., vol. 12, June, 1921, pp. 48-108. Canadian Min. Jour., vol. 42, May 27, 1921, pp. 420-422. Oil and Gas Jour., vol. 20, June 3, 1921, pp. 90-90. Petroleum World (London), vol. 18, June, 1921, pp. 233-2.64, 236-238, 240-241. Bull. Canadian Inst. min. and met., July, 1921, pp. 629-638. Mining and Metallurgy, Oct., 1921, pp. 47-48. Bureau of Foreign and Domestic Commerce. Resources of Balkan and Near Eastern countries. Commerce Repts., Oct. 24, 1921, pp. 488-489. Includes summary of the mineral resources of these countries, mentioning petroleum and allied substances in Roumania, Albania, Anatolia, Mesopotamia, Palestine, Arabia, Persia.

Jan 1, 1921

By William A. Hustrulid

An overall summary and the individual reports of eight workshops to determine research and development needs in western mining ore presented. Problem areas are identified, and recommendations regarding priorities, funding sources, and prime movers are made. The objective of this contract was to identify research and development needs for advancing mining technology as well as health and safety measures for western U.S. Surface and underground mining. This was accomplished by convening a series of workshops where problems could be thrashed out by producers of trona, uranium, open pit copper, underground salt (from the Midwest and New York), underground metal and nonmetal, etc. In addition to problems, future priorities, funding, and the desicion as to who should be the prime mover on R & D were discussed.

Jan 1, 1976

By Edward A. McClatchie

A novel nondispersive electro-optical gas analyzer has been designed, fabricated and tested. The instrument is based on a pressure modulated absorption technique. Key features of this new gas analyzer technique include long-term zero and calibration stability. The technique was investigated for the gases carbon dioxide (CO2), carbon monoxide (CO), methane (CH4) and nitrogen dioxide (NO2). The delivered analyzer was capable of measuring the three species CO, CO2 and NO2. It is a compact (300 cu in) package, is battery powered and weighs 15 lbs. Some thirty readings of each gas may be made on a single battery charge.

Jan 1, 1980

By John P. Hansen

Batches of red or brown iron ore concentrates, weighing 100 or 200 grams, were reduced with gaseous reductants in a laboratory-sized fluidized-bed reactor. Using a loss of weight technique, the rates of reduction were measured and the effects of temperature, gas consumption, and gas flow rates were determined. Below about 725° C the rate of reduction was controlled by the chemical reaction at the reduction interface having an activation energy of about 10 kcal/g mole. Above about 725° C the rate of reduction appeared to be controlled by the flow of the gaseous reductant and therefore to be directly proportional to the flow rate. Above 725° C, hydrogen reduced the iron ore much faster than carbon monoxide. In gas mixtures, carbon monoxide or nitrogen reduced the hydrogen partial pressure and lowered the reaction rate proportionally. When present in large concentrations, carbon monoxide had a serious inhibiting effect on the reduction rate, probably owing to carburization and sintering of the reduced iron.

Jan 1, 1970

By Charles W. Huggins

A study of the high magnification of some inorganic fibers which are found in nature or produced in the laboratory, has been conducted with the electron microscope. This series of electron microqraphs shows the important morphological differences exhibited by potassium-lead silicate, lead-aluminum silicate, chrysotile, wollastonite, silicon nitride, potassium titanate, cobalt chrysotile, magnesio-fluor-richterite, fluor-richterite, refractory oxide fiber, silicon carbide, massive serpentine, and palygorskite. A ribbon or a thin lath 250-2500 A. wide is the structural form of potassium-lead silicate and lead-aluminum silicate. Chrysotile, cobalt chrysotile, and massive serpentine all have a tubular structure and a fairly uniform (150-300 A.) diameter. Wollastonite, potassium titanate, fluor-richterite, and magnesio-richterite crystals have a lath shape, and potassium titanate laths are laminated ribbons. Single fibers of silicon nitride and palygorskite are ribbons, and the silicon nitride sample contains many twins (branching fibers). Palyqorskite fibers are highly flexible and have cross-sectional measurements of 150-300 A. Silicon carbide fibers differ from other fibers because their structure consists of several different forms. The sample used in this study had, predominately, a margarite-type structure. The refractory oxide fiber lost, all its apparent fibrosity after being prepared for electron microscopic examination, and only irregular fragments are visible in the electron micrographs.

Jan 1, 1962

By David C. Chang

A survey of in-situ methods for determining bulk electric properties of coal is given. Largely because of the strong dependence of coals properties on operating frequency, different sensing methods have to be adopted for different applications. Evaluation of both established and feasible methods is made in this report from the viewpoint of physical set-up, probing depth, and the type of inversion involved.

Jan 1, 1977

By M. E. Tyrrell

This Bureau of Mines investigation was made to determine the possibilities of using Florida beach-sand concentrator wastes in ceramic products. Sands used in the investigation originated in the Trail Ridge area of Florida, where continued operation of processing plants for recovering titanium minerals promises a dependable source of raw materials. Three general classes of ceramic products were studied, namely: (1) Structural, (2) refractory, and (3) electric-furnace slags.

Jan 1, 1956

By Edmund S. Leaver

[In previous reports5/ of ore-testing studies standard methods of conducting; test with precious-metal ores selected as representative of certain mining districts were discussed in considerable detail. In addition to standard tent procedures such as direct cyanidation, amalgamation, gravity concentration, and flotation, or a combination of these methods, it is sometimes necessary to apply other methods, such as preliminary roasting and washing of the calcine with plain or acidulated water before cyanidation. In all of this work standard tenting procedure has been supplements by he necessary assaying and analyses of original ore and test products.]

Jan 1, 1941

By J. H. Tylczak

The Bureau of Mines studied the effect of alloy additions on abrasive wear of low-alloy steels. A dry-sand, rubber-wheel abrasion test appa-ratus using ASTM G65-Sl procedure B was used for the abrasive wear tests. Eighty-six material heat-treatment combinations were abrasion tested. Results of these tests were analyzed statistically using regression analysis to see if additions of Cr, Mn, Mo, Ni, Si, AI, Cu, and S were significant in affecting the abrasive wear rate of low-alloy steels. Regression analysis was also used to confirm hardness and C affect on the abrasive wear rate of these steels. It was found that for all the steels taken as a group, increased amounts of Mn significantly reduced the wear rate, while increased amounts of Mo and S1 increased the wear rate. Analysis also confirmed previous research done by others, that increasing hardness and amounts of C reduced the wear rate. For the hardened steels taken as a class, only increasing amounts of C and Mn reduced the wear rate, while increases in Si increased the wear rate. In the class of unhardened steels, increases in C, Mn, and S re-duced the wear rate, whereas increases in Mo increased the wear rate. The steels with the best resistance to wear were two hardened experimen-tal steels similar to AISI 1055 and AISI 107S.

Jan 1, 1986

By Elger. G. W.

The Bureau of Mines investigated preheating of continuously fed, fragmented ferrous scrap charges by furnace offgases and utilizing substitutes for imported fluorspar to condition electric steelmaking slags. Three types of continuous scrap charging procedures were investigated to determine electrical energy consumption in a I-st (short ton) electric arc furnace. Cold and preheated scrap charges were continuously fed at rates averaging 37.5 and 43.7lb/min, respectively. The feed rate varied appreciably from test to test owing to hangup of the scrap in the charge bin. Approximately 7 pct less electrical energy was consumed in melting scrap preheated to 8400 to 1,1100 F by furnace off-gases than in melting cold scrap. Overall energy consumptions were 888 kW'h/st for cold scrap, 829 kW'h/st for preheated scrap" and 637 kW'h/st for conventional backcharged scrap. Stack gases from scrap preheating averaged 1200 F and a flow rate of 1,615 scfm compared with 2200 F and 1,302 sefm for cold-charged scrap. Slag conditioners tested included synthetic fluorspar, boric acid, hydroboracite, used aluminum potlining wastes and aluminum anode tailing wastes, and Sorelflux B. The boron-containing conditioners fluidized the slags the best, followed in order by the conditioners containing fluorine and titanium.

Jan 1, 1987

By Edmund S. Leaver

[In previous reports 5/ of ore-testing studies standard methods of conduction tests with precious-metal ores selected as representative of certain mining districts were discussed in considerable detail.]

Jan 1, 1941

By F. G. Schwartz

The Bureau of Mines developed a rapid and precise method for predicting storage stability of motor gasolines. This method resulted from the investigation of many analytical techniques as well as a study of fuel composition and fuel component gum-forming mechanisms. The first section of this bulletin discusses the development of the prediction test through its several phases, including revision of the standard 110° F storage test; attempts to develop a modification of the ASTM D525 induction bomb test; and the ultimate abandonment of this procedure with the adoption of the 16-hour oven test that was both precise and rapid. The second section comprises a discussion of further studies of fuel com- position, including the reactivity of certain sulfur compounds and hydrocarbons to form gum. The compositions of various gums and inorganic deposits are reported in terms of elemental analysis and spectroscopic examinations. The reactions of tetraethyllead with selected hydrocarbons are also reported.

Jan 1, 1972

By D. R. Corson

The Bureau of Mines instrumented an operating stope in a deep vein mine to determine the amount of wall closure and the magnitude of loads imposed on a backfilled stope. Hydraulic pressure cells used to monitor pressures in the fill) with bolt closure points to measure vein-wall movement and the procedure for their installation) are described) and the results of the laboratory calibration analysis of the reliability of these cells are given. An attempt to monitor density and moisture changes in the backfill with a nuclear density-moisture device was only partly successful) owing to either deformation of access tubing or relative displacements of the vertical vein walls relative to the emplaced tubes. Data from the instrumentation indicate vein-wall closure in excess of 20 inches and pressures within the fill approaching 600 psi. Analysis) incorporating field data with results of laboratory tests of the compressibility of timber and tests defining the constrained moduli of the fill) points out the limited restraint to vein closure offered by timber sets. Ground movement induced by mining activity could be more effectively con-trolled by the use of densely compacted backfill.

Jan 1, 1967

By Michael R. Norland

This U.S. Bureau of Mines report on U.S. and Canadian 1iterature pertaining to soil characterization and the use of soil amendments as a part of the reclamation process of coal surface-mined lands contains 1,280 references. The references were published during the 1977 to 1988 period. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate those articles with the coal mining region and subjects of interest. All references are annotated.

Jan 1, 1991

By Maria I. De Rosa

The U. S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (~300° C) and later (~400° C) combustion stages of chlorinated polyester-reinforced mine ventilation ducts could be predicted by a smoke particle characteristic, for the development of a test parameter. The experiments were conducted in an approximately 20-L furnace, at 14-min durations at set furnace temperatures of 2500 and 1,000° C, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCI), carbon monoxide (CO), carbon dioxide (C02), and oxygen (02) concentrations, furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and average number and concentration (no), and the product of the average smoke particle diameter and concentration (dgno). Results show that the inverse of the smoke particle diameter-concentration product [(l/dgn0)], correlates directly and significantly with the primary gas toxicities evolved during both early (HCI) and later (CO) stages of combustion.

Jan 1, 1989

By J. L. Holman

The Bureau of Mines has extended its previous development of cast Mn-Cu damping alloys to powder metallurgy (P/M) consolidation of alloys containing 55 to 75 wt-pct Mn. Blends of minus 200-mesh elemental powders were compacted cold in directional and isostatic presses. With 1 pct binder, typical green densities ranged between 76 and 80 pct of theoretical when pressing at 30 or 48 tsi. Green strength increased with compacting pressure and copper content. As-sintered tensile strengths ranged to 60,000 psi fox a hydrogen, sintered 60Mn-40Cu alloy, along with 5-pct elongation. Sintered densities ranged between 90 and 96 pct of theoretical. Sintering (a as effective when holding for 1 hr at maximum temperatures of 900° to 1,040` C, dependent on composition. Strength and ductility were considerably lower than for equiva¬lent cast alloys. When aged to the damping condition, alloys containing 60 to 70 pct Mn exhibited >40 pct specific damping capacity (SDC) at 5,000-psi stress, considerably higher than values reported for equivalent cast material. Effects of 1 or 3 pct Sn or Zn additions on SDC and other properties were assessed. Trials were conducted on consolidating rings and gears of the 65Mn-35Cu alloy on industrial-type P/M equipment.

Jan 1, 1979

By T. L. Muldoon

The bagging of dry pulverized products using fluidized air packers creates severe respirable dust problems in many surface mining operations. During bag filling, excess air and product blows by the bag valve/nozzle interface. After bag ejection, dust blows out of the bag valve. During conveying and handling dust is released from the bag valve and dirty bag surface. Overexposure of the bagging machine operator and bag handlers is common. This report describes the development and testing of a new dust control system for bagging machines. The system features a new bag clamp design to reduce product blowby during filling. A controlled vacuum system removes excess air from the bag before ejection, eliminating the problems after bag ejection and during conveying and handling. The system has shown significant reductions in dust exposure for both bag machine operators and bag handlers. These reductions are achieved with no significant effect on total mill productivity.

Jan 1, 1985

By B. C. Parks

This paper is a report on the relationships between petrographic composition, chemical composition, physical properties, and thermal behavior of banded bituminous coal. It describes the relationships between petrographic composition, behavior in various laboratory tests, and carbonizing properties of different petrographic types of coal that occur in relatively thick benches in a single bed of high-volatile A bituminous coal - the Hernshaw bed of Boone County, W. Va. Thin-section microscopic analysis and free-swelling index determinations of the thin-section samples were made of a standard column sample. A standard face sample, a representative channel sample, and representative samples of two prominent petrographic benches of bright and dull coal were subjected to chemical analyses and free-swelling-index, plasticity, dilation, agglutinating, low-temperature carbonization, and BM-AGA retort tests. A float-and-sink separation was also made of part of the standard face sample. The fractions from this gravity separation were subjected to petrographic and chemical analysis and free-swelling-index, plasticity, and dilatation tests.

Jan 1, 1959