Search Documents

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By Tristan Worsey, John Rathbun, Andres Malone

A run of mine, low grade gold heap leaching operation is currently looking to increase ounce recovery by decreasing run of mine fragmentation size. Current blasting practices have resulted in an average fragmentation size of 80% passing 7.05 inches (179 mm). It is estimated that a decrease of 2 inches (51 mm) in the 80% passing fragmentation size has the potential to yield up to a 2.5% increase in the overall life of mine recovery within this ore body. This potential recovery increase could lead to an increase in recoverable ounces which, in turn, would lead to a better profit margin. As this particular deposit is composed of predominantly low grade heap leach the capital investment in a crushing facility was cost prohibitive, it was therefore decided to look into the current blasting practices as a means to improve fragmentation.

Jan 1, 2015

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine.

Feb 1, 2020

By William Hissem

When we look out on our business landscape today, the words higher, faster, fdwther come to mind. Compliance issues, business integration, increasing production and profitability demands are converging in an age old industry and giving it a new twist. Not that the rock changes, rather that as the variables of our business change, the resulting “cut-off grade in business” turns ore into rock or rock into ore. The trick is to emphasize the latter. As with the miners of yore, what was recovered from the business enterprise had a lot to do with tools and skill. So it is today. When the casual observer looks at drilling and blasting operations today, many see the same basic offering in terms of equipment types and process. Looks, however, can be deceiving. As with the aviation sector, a given machine might took similar to previous generations of equipment, but in fact is radically different in terms of power, efficiency, accuracy, and range. So it is with hydraulic top-hammer drills today.

Jan 1, 2000

By Rob Farnfield, Ben Williams, Bob Woolley

This paper outlines how drilling safety standards are being driven forward in the United Kingdom’s surface mining and quarrying industry with developments in equipment, procedures and competence.

Jan 1, 2010

By J Silva Castro, Braden Lusk

Information management is important in all disciplines. In mining; collection and analysis of information before, during and even after mining is a keystone to performance. During mining, information is useful to optimize the resources and make appropriate decisions. Current technologies allow for collecting information in real time. Records of blasting activity at the mine are common practice in surface coal mining operations. The most common blast information recorded contains the location of the blast, scaled distance, geometry of the blast, weight of explosive used and quantity of blasted rock. Sometimes due to the proximity of protected structures, seismograph evidence of the particle velocity and airblast levels is required. However, in the majority of cases, the seismograph information is not linked to the blast information. Blast related information is recorded separately from the seismograph information and seismograms are little more than an attachment to the blast record. This fact makes simultaneous visualization and analysis of the technical details of the blast with the vibration and airblast information difficult.

Jan 1, 2012

By Ronald Ticona

Generally, the drilling and blasting operation are managed independently to the processing plant outcomes. Therefore, the technical segmentation to determinate the ore drill and blast designs do not include processing plant rock properties such as Bond Work Index, Axb, Drop Weight Index or other. This work describes the case study of a copper mine in Peru, which, together with its strategic partner ORICA, have implemented projects focused on optimizing mine fragmentation. The year 2021, mine operation according to its mine plan would have a significantly increased SAG mill hardness, which would impact directly on copper concentrated production. An integrated strategy from mine to plant has become necessary to maintain the production levels.

Feb 6, 2023

By Frank Hirthammer

The paper explains the procedure of implementing Track & Trace solutions for manufacturers of explosives based on customer experiences. By using concrete examples, the process from project start to implementation is described. Lessons learned from the experiences of European explosives manufacturers are presented.

Feb 1, 2020

By B. Corrêa, M. Cavalcante

A large open pit iron ore mine in Brazil, which has a heterogeneous lithology, faces a challenge in defining drill and blast patterns to achieve the expected results. The mine needed to obtain an automated representation of the fragmentation curves and correlate them to the respective blasts, lithologies and quality parameters, seeking the continuous optimization of the fragmentation process and its benefits to the subsequent comminution processes. Trials were carried out for 5 months to demonstrate the functionality of an autonomous fragmentation monitoring system that analyzes the granulometric curve of the material throughout the muckpile and makes the results available online and in real time. The system, which contains a binocular camera, a processing unit and an antenna, was installed in a shovel, to evaluate the following KPI's: monitoring failures, monitoring capacity, physical availability and reportability of oversized boulders. The system analyzed 33,060 samples, with an average capacity of 285 photos every 24 hours, 127 during the day and 158 at night, all measured, analyzed, stored, and made available on its online platform, reporting 223 alerts of P80 above 400mm (15.7 in) and 38 particle sizes above 900mm (35.4 in). The inactive and operational hours of the monitoring system corresponded, respectively, to the idle and worked hours of the shovel, according to dispatch data. There were no camera or processor failures, and rain, dust or poor internet conditions did not impact sampling and fragmentation analysis, indicating 100% physical availability of the system. The autonomous monitoring analyzed 139 times more samples compared to the currently used manual method. In addition to increasing sampling representativeness and automating the process, it increases the safety, quality, and productivity of granulometric analysis, eliminating the exposure of people in the mine and human bias in the analyses. Additional analyses were performed by correlating digitally centralized drill and blast data, data from autonomous drills and fragmentation results. Automated obtention of granulometric curves favors quick decision-making and optimization of blasts to achieve better results in productivity and cost reduction in the plant and mine operation. The autonomous fragmentation monitoring system met the need presented by the mine, proving to be a key tool in continuous improvement projects, including Mine to Plant.

Jan 1, 2024

By W. Boas, R. Silva, D. Yumi, L. Steffen

The continuity of the flow and stages within the mining process is essential to achieve success in its operation and results, especially when it comes to a gold mine. During the first seven months of 2022, crushing at the Morro do Ouro Mine had 19 stops in the primary crusher due to equipment blockage/obstruction, this could be due to the size of the material that was blasted with explosives and fed. The feeding of coarse material to the crushing plant impacts the operation in several ways, for example, premature wear of the equipment, reduction in the supply of the remainder of the beneficiation, reduction of the buffer pile and damage to the conveyed belt. In a mine located far from the community, the fragmentation improvement is mainly related to load increments or some other relatively simple change. However, when it comes to a mine located close to communities, alterations of this type must be analyzed in detail, as it can have an impact mainly in relation to vibration and flyrock. Aiming to improve the efficiency of the blasting, mainly in relation to the result of fragmentation, a project was created to improve the efficiency of the blasting with a focus on reducing the crushing stoppage and reducing the amount of material discarded due to inadequate granulometry. During the evolution of the project, several improvement solutions were proposed, for example adjustment of the power factor in relation to the geological characteristics of the rock mass, drainage, blasting geometry, vibration reduction techniques and several operational improvements. By using the techniques and methods identified as improvements during the project, it was possible to observe and quantify improvements in relation to the fragmentation of the blast. During the months of January to July 2022 there were 19 events. It was estimated that at this rate there would be 14 more blockage events, but there were only 3 events and that meant a 79% reduction in blockage. In addition to the reduction in crushing shutdown events, there was also a 53% reduction in the amount of ore that is discarded due to inadequate granulometry and, with that, the feed rate of the grinding system was able to reach the maximum feed limit due to the material being fed to the mill well fragmented, contributing to increase the production and productivity of the beneficiation process at the Morro do Ouro Mine in Paracatu-Minas Gerais-Brazil.

Jan 1, 2024

By TTE-Europe GmbH

A few years ago, the term Track & Trace for explosives was only known in Europe and Brazil at most; the introduction of this technology is experiencing an undreamt-of boom worldwide. More and more countries are enacting legislation to introduce Track & Trace of explosives and follow Europe and Brazil on this path. At present, the world's leading manufacturers are already using such solutions, are in the process of implementing them, or are in the planning process. However, based on the experience gained in Europe, there are outstanding challenges for all manufacturers. These are questions of compliance, logistics, distribution, and, of course, especially, the necessary adaptation of the production environment. However, this development involves considerable effort on the part of the manufacturers. New devices for marking the explosives and digitally recording the data are integrated into the production process. This should be done as cost-effectively as possible, without restricting production capacity and speed, and with as few process changes as possible. This paper uses real-life customer experiences examples to explain paths from project design to real implementation. Lessons learned from the experience of European explosives manufacturers are presented, missteps are described, and solutions are identified. Individual steps along this path are explained, and solutions are told to avoid pitfalls and bottlenecks. Finally, it refers to the risk analysis and concrete examples in implementing the planning into production. Methods of marking various explosives are shown, and the use of Track & Trace to solve logistics tasks in picking and shipping explosives, including the data exchange with ERP (Enterprise Resource Planning) systems.

Jan 26, 2026

By Andrew Theobald, Peter Dare-Bryan, Trevor Byers

The use of advanced modelling techniques and the timing flexibility of electronic initiation systems allows for unprecedented control over blast outcomes as shown in several complex blasting problems experienced by the open pit operation Xstrata Ernest Henry Mine (EHM) in north-west Queensland, Australia.

Jan 1, 2010

By Lloyd Litwin

The ARTA 2008 Project (Alpha Ridge Test of Appurtenance) was a Canadian Government sponsored deep water seismic survey carried out on the high arctic permanent polar ice cap. This Geological Survey of Canada operation was the second seismic research project in the high Arctic and was monitored by the Danish Government. Utilizing 100% air support from Eureka and then helicopters from an ice based tent camp north of Ellesmere Island, the five week study was accomplished in the early spring just after the sun returned to the far north.

Jan 1, 2011

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

By Lauren Shields

This paper discusses the application of current fragmentation models for underground blasting, establishes a conceptual fragmentation model for underground operations, and discusses the applicability of the mine-to-mill approach for underground blasting. Additionally, this paper also discusses selected case studies where the mine-to-mill approach is applied to underground mining operations.

Feb 1, 2020

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

Feb 1, 2020

By S. Evans, J. Phillips-White, D. Morton

The partnership between Orica and MMG at the Dugald River Zinc mine in Australia has led to the first global field trials and deployment of Orica’s Subtek™ 4D™ (hereafter referred to as 4D) Bulk Systems underground bulk emulsion blasting technology. This technology offers advantages over conventional bulk explosives by extending the range of energy and length of explosive column that can be charged in underground production. 4D gives blast designers energy options between Relative Bulk Strength (RBS) 50 - 150, delivered uniformly along the entire column in most blasthole conditions along with the ability to instantaneously modify the energy within an individual blasthole. During Phases 1 – 3 of the project from October 2022 to January 2023, over 57 tonnes of the 4D Underground emulsion were loaded in 17 stopes. The primary objectives of this phase were to reduce hanging wall dilution and improve stope recovery. While drilling and other parameters remained unchanged, the energy selection was tailored for specific situations, guided by a revision to the site's drill and blast standard. The design used low energy (RBS 50 - 70) in holes adjacent to the hanging wall and high energy (RBS 130 - 150) where stope recovery had historically been challenging, such as at the toes of long downholes. Initial results of the project focused on five stopes selected for their similarity to those used for the baseline data set. Although the 4D data set was small, the post-blast scans indicated favourable results for recovery and dilution. This suggests that selecting and delivering bulk explosive with tailored energy levels can improve stope performance.

Jan 1, 2024

By Scott G. Giltner, Alex Schwenk

This paper is an update on a paper presented at the 2022 ISEE conference. The original paper presented how the mine operator desired to open up ore reserves near several mine structures including two crushers, the conveyor belt drive and the concentrator thickeners. In order to open up additional ore for extraction (over 3 million long tons or 3 million tonnes) it was necessary to blast out two benches near the mine structures. Since the two benches have been successfully shot, the mine has now conducted nine production blasts in this area at distances as close as 116 m (380 ft) to the two primary crushers. These production blasts are full size production blasts consisting of up to 300 or more blast holes. For these blasts the two primary crushers were still the critical structures as they were the production life blood of the mine. If the crushers were shut down due to any damage from the blasting, the revenue of the mine would be adversely affected. As with the initial bench blasts, two issues provided an extra challenge to the blast design. The first was that the blast holes were still considered large diameter at 12¼ inches (311 mm) and 16 inches (406 mm). The second issue was that the bench heights were short, with the average varying from 34-40 ft (10.3-12.2 m). This combination of large diameter blast holes with a short bench provided an unfavorable geometry for the goals established by the mine management. The mine management established the following goals. 1) None of the mine structures would be damaged by fly-rock. 2) Minimize the blast vibrations at the crushers. 3) The last goal was to produce a muck pile that could be dug easily by hydraulic shovels. Electronic detonators were applied to achieve the necessary control of the blast and optimal fragmentation throughout the mine. UAV surveys of the blast area were also conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. The results of the nine blasts have provided what the customer requested. The peak vibration level at the crushers for the nine production blasts was 1.6 in/s (40.6 mm/s) at a frequency of 18.9 Hz. There have been no fly-rock or blast vibration issues at any of the nearby mine structures. As a result, the mine has been able to maintain its production with no downtime. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017