Search Documents

By Paul Sterk

In underground mining a great deal of time, money, effort, and resources have been used in the effort to minimize blast-induced damage. This damage occurs to the back, ribs, and pillars when the energy of the explosive is released back into the rock due to over confinement or the overloading of explosives in the perimeter holes. This damage can result in roof falls, dilution of ore, excessive rock bolting, scaling, screening, shot-creteing and other safety and support issues.

Jan 1, 2003

By Constanza Bujes, Mark Jones, Graham Crook, Yansan Jamyanbaatar, Sedat Esen

Tracking ore characteristics such as grade and hardness from its original position into the material handling and processing stages remains one of the key challenges in open pit mining of hard rock deposits. The most efficient technique for rock fragmentation and separation of ore from waste is blasting, which induces changes in the grade distribution by displacing the in-situ ore into a diggable muck pile. Material movement defines the post-blast grade distribution, which is key to optimising the value of the ore and accounting for ore loss and dilution. Techniques to directly measure the displacement in open pit mining have been implemented routinely and have provided calibration and validation data for blast models to build upon. The JK Value-Based Ore Control blast movement model (JKVBOC) is the latest development of a series of research studies into blast movement and ore control at the Sustainable Minerals Institute of the University of Queensland. The blast model discretises the bench into blocks, defines the initial velocity of each block based on the blast design, confinement and explosive properties, and simulates the displacement using a physics engine. Calibration and validation of the model has been performed in open pit hard rock mines in Australasia in diverse confinement conditions. This paper describes the calibration and validation of the blast movement model against direct measurements of blast movement and final muck pile shape for a case study where the displacement of multiple shots was modelled for an open pit mine, with an analysis of the implications for ore loss and dilution. A key finding in this study is the need for further integration of this technology into the existing systems for ore control, and the potential for applications in tracking ore characteristics other than grade into process control.

By Gerard McAlinden, Daniel Frost, Patrick McAlinden, James McAlinden

In an effort to recover Polychlorinated biphenyls (PCB’s) that had leached into bedrock below the Hudson River in Upstate New York, a shaft and tunnel complex was designed that would allow installation of inclined and vertical wells into the zones of contamination to recover PCB’s by gravity. A joint venture of Merco Inc., of Lebanon, NJ, and Obayashi Corporation, of San Francisco, CA, was awarded the contract for constructing the first Tunnel Drain Collection System in the world. Conventional drill and blast techniques were the most economical method to construct the project but due to the presence of PCB’s and community concerns, innovative drill and blast practices were needed.

Jan 1, 2010

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Gabe McClain, Thomas Pallua, Joe Schrank, William C. Gates

Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds

Feb 1, 2020

By Michael Laing

Blasting regulation and restrictions are tougher today than ever before. When blasting in population centers, strict limitations are often placed on the environmental effects caused by blasting, more specifically vibration and overpressure. Blast-induced vibration can be a tricky thing to manage at times, but there are a variety of options at our disposal to help optimize and manage vibration. This paper focuses on the application of rudimentary signature hole analysis to optimize blasting vibration in localized areas surrounding a mine.

Jan 1, 2017

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes. Accurately capturing and modeling this geology is the key to controlling high air blast. 3D modeling and profiling by drone is the solution to understanding accurate face profiles and real minimum burdens. Using 18 months of blasting data and air blast results to establish a baseline, the comparisons between blasts designed with 2D profiling and blasts designed with drone 3D profiling show improvement in air blast levels. Additionally, shots with completed drilling were drone profiled to understand precise amounts of burden for each borehole. This 'audit' of a blast allows for custom loading of explosives, accommodating the amount of burden present on the blast face. 3Dprofiling is not a new tool in the blasting industry, but a drone alleviates some of the restrictions ground systems face. Controlling and managing air blast, as it pertains to face burdens, requires an understanding of those burdens from all angles. A drone provides that distinct level of insight. The results of this study indicate that drone profiling is managing the customer's air blast readings, allowing the customer to maintain their license to operate within the community.

By Ajoy Singh

A study was conducted to investigate the damage potential to underground multi-seam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with higher amplitude of vibration compared to pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or high. The vibration magnitude recorded was higher in upper seams openings than in below seam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.erground Coal Mine

Jan 1, 2012

The following situation was submitted as an ethics case study for inclusion in the Journal. To the best of our knowledge, they are based on actual circumstances encountered in the field. Blowing the Whistle Protecting Confidentiality or Doing the Right Thing? This case centers around a construction job and involves a contractor, subcontractor/blaster, and a farmer/homeowner who lives near the job site. It is essentially a study of professional ethics versus morality, our professional code of conduct versus what is right or wrong.

Jan 1, 2007

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981

By David Porter, Nathan Rouse

The implementation of presplit blasting has been widely utilized in open pit and underground tunneling. This case study works through the iterative process of developing a heading drill and blast design to control overbreak and limit backbreak in cut and fill headings. The initial design was based on rule of thumb parameters, and the design was then modified for the field conditions based on results. Throughout the design process the drill profile, explosive charge, and timing were modified to yield the best profile compared to design. Data collection during the design process was extensive to best understand the effect of modifying parameters, and gauge performance of design changes. Input from the miners as well as engineers was considered to allow for the best possible adaptation of the design change from existing practices. During the process resistance to change was realized and accounted for to understand the issues that the miners were facing and how to best address them while ensuring high quality blasting. Workforce buy- in was addressed by illustrating the long term benefits of higher quality blasting and the tradeoff of with a slightly more in depth drill and loading cycle.

Feb 6, 2023

By M Sampara, W Comeau

The introduction of large-diameter holes to underground mining has made possible the development of new mining methods such as the Vertical Crater Retreat (V.C.R.) method. It is not only the safest underground excavation system but also provides mass production at a lower cost than any conventional mining method (1, 2, 3, 4, 5).

Jan 1, 1981

By William Reisz

In our line of work,like many other professions, there may be times when circumstances or a series of events may arise, contributing toward unacceptable risk. When multiple parties are involved, there will almost inevitably be differences on how best to deal with these situations. Unless approached in an intelligent and these differences may often have the potential for costly and unexpected results.

Jan 1, 2014

By Mauro Fornaro, Marilena Cardu, Renato Mancini, Daniele Castano

Tunneling by explosive blasting in civil works isn't merely intended to break somehow a way through the rock, rather to drive a permanent, constant cross section, lined way. The current mechanical excavation v/explosive blasting debate is mainly centered on the concept of the tunnel wall quality; and consequently explosive blasting strategy is founded on contour blasting.

Jan 1, 1992

By Bill Birch, Toby White, Ian Brown

costs/benefits of electronic detonators and measure their effects on primary crusher productivity. 9 blasts (3 shock tube blasts, 6 electronic blasts). Measured electricity consumption & primary crusher throughput. Change to Electronic Detonators resulted in a 7% reduction in primary electricity costs and a 15% increase in primary crusher productivity.

Feb 1, 2020

By Lyall Workman, Jack Eloranta

Blasting has an important impact on mining and milling well beyond the necessary ability to dig and load the ore efficiently. There is an increasing body of blasting research indicating significant impacts in crushing and grinding. These include increased production through higher output and fewer delays for bridging and jamming by oversize. In addition, fragmentation better suited to the crushing and grinding system is indicated to lead to reduce energy consumption by these activities, an important result in today’s environment. An important component of optimum fragmentation for this purpose appears to be micro-fracturing within individual fragments. This differs from fragmentation criteria for loading which focus mostly on fragment size. Therefore, one must analyze blasting broadly to obtain satisfactory results throughout the operation.

Jan 1, 2003

By Tony Rorke, Sydney Thabethe

A large overburden blast was carried out at Douglas Colliery, Middelburg Mine Services, close to a national road in South Africa. The road is a busy route between Witbank and Bethal and damage to the road could not be risked. The section of road next to the blast was particularly prone to damage, because it had been mined out on its eastern flank, and the large blast was to take place on its western flank. There were thus three potential damage risks: 1. Fly rock damage to the road surface 2. Vibration damage to the road substrate 3. Damage caused by bulk displacement of the block supporting the road into the void on the mined out side. This paper presents the design and blasting methods used to control the blast and avoid these three risks. Electronic delay detonators were used in multi-decked holes. Signature data were used to determine the blast timing to make sure that delays were used that would provide destructive interference. The timing direction and sequence was decided using wave interference patterns to direct repeated shocks away from the road. The precise detonators and the odelling capability allowed effective control of the blast vibration result. Each hole was charged with two explosive decks separated by a deck of aggregate to limit the charge mass fired per delay and thus limit the reaction forces acting towards the unsupported road. The vibration and blast results are presented in the paper, together with the design that was applied. Details are provided on how the blast was charged and primed. The detonators that were used are described and the timing design is presented.Copyright © 2004 International Society of Explosives Engineers 2004G Volume 1 - Blasting Next to an Unsupported Road Using Electronic Detonators 1 of 13 It is concluded that damage risk to nearby structures can be effectively controlled using electronic delay detonators, provided the appropriate modelling is applied to obtain the most effective delay periods.

Jan 1, 2004

By Ron Gilbert

Every day, demand increases with over all population; supply must follow. People must have more food, shelter, and mobility. Raw materials must be mined. Roads, trenches and foundations support the quality of life.

Jan 1, 1996

By Tapan Goswami

The main objective of the blasting phase in a coal mining operation is to maximise the coal recovery. However, coal loss due to blasting is a serious problem. The Australian Coal Association Research Programme (ACARP) reported in 2011 that in Australia one in every ten coal mines is completely wasted due to such losses. Coal is either lost in the spoil, largely due to the blasting operation or becomes diluted and cannot be recovered entirely. The major coal loss mechanisms include losses from the coal seam roof, the floor, the front edge and from dilution. Coal damage and loss mechanisms during cast blasting that have been observed by various authors include: •Excessive cast dragging the coal edge in the cast direction. Movements of this nature are oftenassociated with the formation of trenches. •Spatial movement of overburden where rock shears and moves in a plane above the coal seam,which damages and dilutes the coal. •Rock falling over the coal during the blast often producing indentations in the exposed coal. •The inappropriate use of bulk and initiating explosives that often results in coal damage. •Insufficient stand-off distances from the coal. The Australian coal mining industry has gone a long way towards addressing the coal loss issues since 2011: almost all operations now deploy touch-coal drilling and sporadically use gamma logging for loading overburden. A study was conducted to compare the effectiveness of touch-coal information in which some touch-coal blastholes were drilled on a fixed or random pattern. In another study, some blastholes were drilled to the touch-coal, gamma-logged and mapped to determine stand-off distances. It was found that the coal roof surface created by gamma-logged holes was the most effective option for minimising coal loss. As a result, a variable stand-off distance was found to be the key to minimising losses. This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.