Search Documents

By M. Abdollahy

Solvent extraction of gallium from Bayer solution of Jajarm Alumina plant was investigated us-ing Kelex100 as extractant. Taguchi experimental design method was used in order to optimize the separation factor of Ga and Al. Optimum conditions were obtained as follows: Temperatuer: 65°C, volume ratio of aqueous phase to organic phase: 3.0:1.0, process time: 60min and organic phase containing 15vol.% Kelex100, 5vol.% isodecanol in kerosene. In this conditions, 74% gallium and 0.3% aluminum was extracted and separation factor was obtained 828.63.

Jan 1, 2014

By G. Önal

Recovery of nickel and chromite from the tailings has been studied on the samples with 0.214 % Ni and 5.10 % Cr2O3 content and taken from Orhaneli Chromite Concentration Plant. Mineralogical examinations of the samples showed the existence of chromite, olivine, pyroxene, chrysotile, anti-gorite, chlorite, idingite, tremolite and calcite together with trace amounts of millerite, pentlandite, pyrite, pyrrhotite, hematite and limonite type iron oxide minerals in partially serpantinized dunite type particles. In order to recover chromite from Chromite Concentration Plant tailings Mozley Table and Knelson Separator are used and concentrates containing approximately 42% and 46% Cr2O3 are produced respectively with 40% recovery. Most of the nickel remained in the tailings. Therefore, acidic leaching tests are performed in order to dissolve nickel from these tailings. Effects of particle size, acid concentration, temperature, leaching time and solid/liquid ratio on the nickel leaching efficiency are investigated. The optimum leaching conditions are found as 250 g/L acid concentration, 1/5 solid/liquid ratio, 2 hours of leaching time and 60°C temperature, almost all nickel is dissolved at the optimum conditions and acid consumption is about 841 kg/t. Repeated leaching tests are carried out in order to have enough Ni content in the leach liquor for the further treatment of solutions. After repeated leaching tests, leach liquor contains 3 kg/m3 Ni, 48 kg/m3 Fe, 2.2 kg/m3 Si, 23 g/m3 Cr and 590 kg/m3 H2SO4. Ni is recovered from that solution by precipitating with H2S followed by HNO3 dissolution and precipitating Ni as hydroxide with 63% Ni content. Leach cakes are subjected to the gravity separation (Mozley table) to recover the remained chromite and a chromite concentrate with 47% Cr2O 3 content is produced with 53% recovery. As a result of the abovementioned tests, a conceptual process flow sheet is proposed for the treatment of these chromite concentration plant tailings.

Jan 1, 2014

By T. Fujita

The incinerated bottom ash includes titanium oxides and a small amount of chromium oxides. Initially, 89 % of chromium was removed from ash at magnetic flux density at several stages of wet magnetic separation from 0.05 T to 6 T. The bottom ash from an industrial waste incineration process includes about 10 % of TiO2. The minerals that contain titanium are rutile and perovskite. These minerals are paramagnetic and show low magnetic susceptibility, therefore, the high magnetic field strength, created by a superconducting magnet, is necessary to capture these minerals. At the first stage of separation, a magnetic field strength of 6T was applied in order to attract the particles that contain iron oxides to the higher magnetic field region. At the second stage of separation, the magnetic capture rate of weekly magnetic particles decreased with increasing the magnetic susceptibility of the aqueous solution (i.e. the medium for dispersing the particles) in order to separate the highly magnetic materials. The para-magnetic salt such as ferric chloride was dissolved in the water to increase the magnetic susceptibility of the medium. After a two-step wet HGMS with superconducting magnet, the grade of TiO2was increased from 10 % to 28 % with a recovery of 64 %.

Jan 1, 2014

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

"Oxidized nickel ores are important source for nickel production in Russia. Considerable explored reserves of oxidized nickel ores with relatively low nickel content, about 0.6-1.4%, are concentrated in the Ural region of Russia. Conventional process flowsheet with the use of blast matte smelting, applied in particularly by JSC “Ufaleynickel”, proves itself as extremely low-margin technology. This paper will examine development of a new more cost-efficient process involving integrated treatment of oxidized nickel ores using the ore from Serovskoye deposit as an example. Target products of this process are hydrate residues containing up to 15 % of nickel and 0.3 % of cobalt, as well as saleable salts of magnesium sulphate and ammonium suplphate. This innovative process includes roasting of a mixture composed of ground ore and sulphuric acid at 650 °?. Sulphate roasted product is then leached in a weak sulphuric acid solution with the following separation of liquid from insoluble solids. Sulphate solution is neutralized by aqua ammonia in two stages until media pH is 3.0-3.5 and 7.5-8.0 with detachment of iron- and nickel-bearing hydrate residues respectively. The mother solution is boiled out resulting in salt crystals which are then dried and roasted at 500-600 °? to obtain magnesium sulphate. The gases generated during salts roasting are captured with production of ammonium sulphate. The developed technology demonstrates higher potential in terms of its economics and eco-efficiency comparing with the conventional process. This innovative technology for integrated process of oxidized nickel ores was patented in Russia.INTRODUCTION Development and industrial implementation of efficient technologies to process oxidized nickel ores is a very important task for non-ferrous metallurgy of Russia. The main reasons for the required technical upgrade of the plants processing oxidized nickel ores is depletion of rich ores, increase of energy resources costs, amplification of environmental and production standards. Due to this, transition from conventional pyrometallurgy to cost-effective hydrometallurgical technologies of ore liberation and solutions processing is logical and corresponds to the worldwide practice of Ni production from oxidized nickel ores."

Jan 1, 2018

The Arctic is a region of special economic, geopolitical, research, socio-ethnic, and defense interests of both Russia and other countries of the Arctic zone. Introduction of innovation technologies at ore-processing factories is a direct responsibility of the state and this problem should be solved on the basis of coordination of interests of different stakeholders. The task of elaboration of scientific principles of rational state regulation in the North is very topical. Innovations require considerable investments first of all from private capital. However as an investment object innovations are not attractive for investors as they require large expenditures for long-term projects, and they are connected to high risks because market incentives form striving to get quick profits of private companies and result in a certain behaviour strategy while innovations need ?long money?. Under such conditions without state regulation of investment and innovation activities development of the mining sector in the Arctic practically has no prospects. At innovation development of mining enterprises economic growth is provided at the expense of active state innovation activities. The elaborated strategy of ore-processing enterprises should correspond to the modern paradigm of the ore-processing industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the AZR which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents. The main principle of creation of innovation technologies is to obtain more products of higher quality with minimal costs. This allows increasing ?productivity of the resources? several times. This principle makes increasing productivity of the resources the most important and in this case efficiency of use of the resources brings extra profits at the expense of lack of new costs such as payment for protection and utilization of wastes. According to the economic theory only ratio between demand and supply is able to fix optimal proportions in economy and to give necessary signals for investment activities of mining enterprises. In this context market for minerals and increase of mineral resources productivity do not create incentives for investment activities without which neither sustainable economic growth nor solution of macroeconomic tasks are possible. Nevertheless countries should not reject this idea in spite of economic efficiency of the enterprises. Extraction degree of useful components and especially oil in the Arctic zone is one of the lowest in the world. This can lead to crisis of oil industry and other mining sectors. The reason for that is lack of a state policy of realization of innovation technologies in the mining sector in the Arctic.

Jan 1, 2014

By J. P. Dai

The Fankou Mine in Guangdong province, China, processes a polymetallic ore containing averagely 4.2% Pb, 8.5% Zn, and 90 g/t Ag. The main metal minerals including sphalerite, galena and pyrite are very finely disseminated and unevenly occurred in the ore, making it difficult to liberate them from each other. This paper presents the processing technology of the Fankou plant and the characteristic features of the novel technology applied.

Jan 1, 2014

By M. F. He

The depression of pyrite in marmatite flotation by a new depressant Sodium Glycerine-xanthate (SGX) has been investigated through microflotation, zeta potential, and adsorption measurements in systems open to the atmosphere. The flotation tests of single mineral show that in the presence of SGX, marmatite can be activated by Cu2+ and shows good flotability, while pyrite can?t be activated and therefore shows poor flotability, as a result these two minerals can be separated using butyl xanthate as the collector. The depression mechanism of SGX on sulfide minerals is discussed based on Zeta potential and adsorption isotherm. Zeta potential experiments demonstrate that at the presence of Cu2+, SGX can strongly adsorb on the surface of pyrite, while it can?t adsorb on the surface of marmatite, thus the results are in accordance with those of flotation experiments; the results of adsorption isotherms show that the adsorption density of SGX on pyrite is greater.

Jan 1, 2014

By B. Q. Xiao

The nitrate content is an important factor for environmental water samples and flour. In a 0.35 mol/L H2SO4-2NO solution, has a strong catalyzing function on the decolourization of Gallocya-nine (GC) oxidated by NaBrO3. Based on this, a novel method was developed to measure the NO and -3NO concentrations in water and flour. The flow injection technology was introduced into the analysis system. A single-valve dual- cingulums to inject which the Copperized-Cadmium slice and the reduction zone are isolated. The optimum solution for this method contains 1.48×10-4 mol/L GC, 0.06 mol /L NaBrO3 and 0.2 mol /L of NH4-2NOCl. Two empirical equations were proposed to calculate the and -3NO concentrations based on the measured signals. It can be used to measure -2NO of from 0.001 mg / L to 2.0 mg/L and -3NO of from 0.002 mg / L to 2.5 mg/L. The measurement frequency can be up to 20 samples / h. The relative standard deviation for eleven samples is less than 5%.

Jan 1, 2014

By Z. Y. Ma, M. D. Liu, Z. Z. Liu, J. K. Zhou

"An optimization method of microwave assisted leaching of copper anode slime was proposed based on Taguchi method. The results showed that the solid-liquid ratio was the most important factor affecting SNR(signal noise ratio) of the copper, tellurium and selenium leaching efficiencies, and its contributions to the copper, tellurium and selenium leaching efficiencies were 58.34%, 55.54% and 60.74%, respectively. Solid-liquid ratio was a significant factor to SNR(copper, tellurium and selenium). Reaction period was a less significant factor to SNR(copper and tellurium) and concentration of sulphuric acid was a less significant factor to SNR(selenium) while microwave power was an non-significant factor, its contributions to the copper, tellurium and selenium efficiencies were 3.22%, 11.73% and 12.73%, respectively. The optimized parameters of the microwave assisted leaching of copper were as follow: microwave power of 500 W, reaction period of 10 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The optimized parameters of the microwave assisted leaching of tellurium and selenium were as follow: microwave power of 800 W, reaction period of 15 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The validation experiments under the optimized conditions has been carried out, the copper, tellurium and selenium leaching efficiencies were 98.66%, 84.32% and 64.54%, respectively. INTRODUCTION As important valuable by-products, copper anode slimes are collected from the bottom of the electrolytic bath in the electrolytic copper refining process(Kilic, 2013). The value of the anode slime is determined by the content of rare metals and precious metals(Liu, 2014). Generally, pretreatment of copper anode slime is the first stage of the whole process. The aim of the pretreatment process is to remove Cu, Te and Se etc and enrich the valuable metals. The methods of pretreatment process can be differentiated into: pyrometallurgical processing and hydrometallurgical processing(Amer, 2003). The hydrometallurgical processes are more promising compared to pyrometallurgical processes in terms of cost effectiveness, low energy consumption and environmental concerns(Ranjbar, 2014). However, the disadvantages of the hydrometallurgy process are evident, such as lengthy processing times and low efficiency. Therefore, it is necessary to develop a highly efficient and environmentally friendly pretreatment method."

Jan 1, 2018

By S. M. Bradshaw, R. Smith, J. H. van Vreden, C. A. Snyders

"The re-treatment of gold tailing heaps has shown to be a potentially significant revenue stream for both large and small scale gold companies. Limited access to capital and lack of skilled labour remain restrictive especially when dealing with a refractory ore and/or where limited amount of material are available. Alternative techniques such as low temperature pre-leaching options to unlock value are therefore in demand. Several low temperature pre-leaching experiments in acidic and alkaline solutions, followed by cyanidation were performed which ultimately led to the further investigation of a caustic pre-leaching step. It was found that the Au recovery from a refractory ore tailings heap could be significantly improved from ˜ 15 to 20% to greater than 60% with a simple atmospheric NaOH pre-leaching step. It was further considered, that since the NaOH pre-leach liberate the Au associated with refractory sulphide minerals, the overall process may benefit by the inclusion of a froth flotation step to separate refractory sulphides from the free milling ore. Froth flotation on weathered tailing heaps are, however, known to be difficult, ultimately resulting in poor recoveries. A process flow sheet, incorporating a caustic pre-leaching step and a process which includes flotation and caustic pre-leaching of the concentrate, are technically evaluated and ultimately compared to simple cyanide re-processing. INTRODUCTION South Africa consists of a large number of gold tailings dumps. Janse van Rensburg (2016) estimated that there was about 517 dumps in the Gauteng area, covering approximately 320 000 ha of surface area. Recovering value from the dumps has received a great deal of interest but can be problematic due to the dumps often being refractory, preg-robbing and weathered. High recovery of valuable metals (Au and Ag) are possible (Fleming and Brown, 2010) but would most likely require pressure oxidation and subsequent neutralisation which can be very capital intensive demanding a high skill set to operate and maintain. In addition, these flowsheets target high processing tonnages due to the economy of scales at the lower grade feed materials, further increasing the capital requirement."

Jan 1, 2018

By V. A. Ivanova, T. N. Perunkova, N. O. Dorozhanova, G. V. Mitrofanova

"Oxyethylated compounds are used as reagents-regulators in the flotation of non-sulfide ores, in particular, apatite-containing ores. Thus, the necessary degree of selectivity in the flotation separation of two calcium-containing minerals of apatite and calcite is achieved only by using, in addition to a collector, regulators-reagents from the nonylphenol ethoxylates class. In order to establish the most optimal structures, this paper presents a comparative assessment of the physical-chemical and flotation properties of several classes of oxyethylated compounds - alkylphenol ethoxylates, aliphatic alcohol ethoxylates and oxyethylated carboxylic acid. The authors have studied their dispergating ability with respect to the air phase and calcium soaps of the carboxylic collector. Dependences of foaming properties of regulators on the degree of oxyethylation have been determined. Adsorption isotherms of sodium oleate on apatite and calcite in the presence of regulators have been obtained. It has been shown that the presence of oxyethylated compounds in the solution reduces the amount of the adsorbed fatty acid collector. The influence of the considered classes of regulators on apatite flotation has been studied. The interrelation of flotation properties of oxyethylated compounds and their molecular structure has been established.INTRODUCTION Flotation plays a leading role in complex apatite-containing ores processing. However, two calcium-containing minerals - apatite and calcite, which compose apatite-carbonate ores, are characterized by close flotation properties. Selective separation of these minerals is a difficult task, the solution of which is impossible without using reagents-regulators. One of the ways to ensure the selectivity of the flotation separation of calcium-containing minerals is the use of reagents-depressants such as sodium silicate, starch, cellulose derivatives, and others (Liu et al., 2016; Rao et al., 1989). Another method is the application of nonionic reagent regulators (Filippov et al., 2016; Filippova et al., 2014; Ignatkina, 2017), which contribute to the adsorption of the ion collector (Filippov and Filipova, 2006 Rao and Forssberg, 1997) and stability of formed froth (Sis and Chander, 2003)."

Jan 1, 2018

By J. Yianatos

The regrinding stage is necessary to achieve the particle size (liberation) for the final upgrade in the cleaning flotation process. At present, vertical mills (Vertimill) are employed at industrial scale, using small steel balls as grinding media. The regrinding process characterization requires mixing regime knowledge along with the mean residence time of the liquid and solid phases. The residence time distribution (RTD) and the actual mean residence time estimations from theoretical relationships are complex due to the presence of three components (solid mineral, balls and water), mass transport characteristics and segregation affecting solid holdup. Therefore, the experimental RTD determination is suitable for industrial mills. In this work, RTD measurements were performed in two different industrial flotation plants. Both plants operate with Vertimills of 1000-1500 HP in the regrinding process with different circuit arrangements according to the plant treatment capacity. The RTD was measured using the radioactive tracer technique. This technique allows for non-invasive tracer detection where the procedure consists of selecting a liquid (Br82 in aqueous solution) or solid (irradiated solid) tracer for RTD data acquisition in real time. The RTD was modelled by the Large and Small Tanks in Series (LSTS) model, which allowed the characterization of the different mixing regimes for both liquid and solids in the regrinding mills. Effective mean residence times in the range 2-11 min were obtained with RTD shapes similar to those obtained in tumbling ball mills. It was found that residence times of liquid and fine particles were similar, which is consistent with results observed in other mixing systems, e.g. mechanical flotation cells. Also, the mean residence times estimated from the RTD allowed the mass balance adjustment to be validated from metallurgical sampling data. RTD estimations are useful for better understanding the Vertimill behaviour and to identify the actual breakage rates. Keywords: vertical mill, residence time distribution, particle size, modeling

Sep 1, 2012

By N. Vorob?ev-Desyatovskii

The process of gold(I) adsorption on activated carbon (AC) from aqueous Na[Au(CN)2] and the state of the adsorbed gold cyanide complex on the adsorbent surface was investigated by photometry, XPS, XANES methods. By DFT method, quantum-chemical calculations were performed of the gold cyanide species on activated carbon surface. It was established that the binding of gold(I) with the surface of carbon involved several simultaneous processes governing the selective adsorption of gold(I) from the cyanide solutions.

Sep 1, 2012

By Nina Panteleeva, Elena Afonina, Stanislav Titkov, Jury Buksha

"Flotation processing of water-soluble minerals (potassium ores, sedimentary salts of salt lakes) is currently the main method for production of potassium fertilizers and concentrated carnallite which is the initial product for production of metallic magnesium. Flotation of sylvite (KCl) and halite (NaCl) is carried out in the electrolyte solutions: KCl-NaCl-H2O and KCl-NaCl-MgCl2-H2O. The report presents the results of studies of the effect of concentration and the electrolyte type on the size of air bubbles in a flotation cell in comparison with the floatability of mineral constituents of potash ores. The floatability in electrolytes of various compositions has been studied: - of sylvite (KCl) by alkylamines, - of halite (NaCl) by alkylmorpholines, - of silicate-carbonate slimes contained in the ore by ethoxylated surfactants. The reagent modes (regimes) activating the flotation desliming of potash ores have been developed."

Jan 1, 2014

By Jin Duan, Qi Zheng, Bo Yan, Li-cheng Ma, Xiao-kui Che

"The aim of this study was to develop an approach for the selectively removal of Zn(II) from heavy metal-bearing-wastewaters produced by gold chemical industry using magnetic chitosan based adsorbents. Chitosan beads were prepared by cross-linked modification of Fe3O4-chitosan bead using epichlorohydrin as the cross-linker. Both Zn(II) inprinted magnetic chitosan hydrogel bead (Zn-MCHB) and unprinted magnetic chitosan hydrogel bead (MCHB) were prepared and batch adsorption experiments were used to evaluate their adsorption capacities and selectivities. Single adsorption of Cu2+, Pb2+, Zn2+ and Ni2+ showed that both MCHB and Zn-MCHB adsorbs all the four metals and had an affinity in the order of Cu2+ > Pb2+ > Zn2+ > Ni2+. The binary adsorption revealed that the two adsorbents preferentially adsorb Cu2+/Pb2+ from Zn2+-Cu2+/ Zn2+-Pb2+ binary systems. However, MCHB does not show any selectivity in Zn2+-Ni2+ system. In contrast, Zn- MCHB preferentially adsorbs Zn2+ from Zn2+-Ni2+ binary system. Furthermore, the adsorption selectivity is predictable from stability constants of the metals with the amino group of chitosan. The information revealed in this work can be used for further applications in the treatment of wastewater containing a range of heavy metals from the gold chemical industry."

Jan 1, 2014

By A. V. Faiberg

Currently, the interest to conditioning of cyanide-bearing recycled solutions with high-grade of base metals, in particular, copper has significantly grown. This can be explained by two major factors. Firstly, there are strict regulations on cyanides amount in tails and higher cost of detoxification processes. This problem can be easily solved during the ore treatment using the conditioning of solutions and water recycling. Secondly, the presence of other metals minerals which react with cyanide during gold leaching resulting in high cyanide consumption. The presence of copper is a major problem. Many copper minerals react with cyanide with the formation of cyanide complexes-Cu(CN)2-, Cu(CN)32- and Cu(CN)43-. One mole of copper consumes 2-4 moles of free cyanide. Availability of cyanide-soluble copper minerals has deleterious effect on gold leaching (gold recovery, cyanide consumption, tails detoxification, efficiency of gold elution and electrowinning). The precipitation of copper from the solutions improves gold recovery by CIL. The removal and recycling of cyanide allowed the reduction of cyanide addition to the process. The recycling of spent cyanide-bearing solutions based on the removal of copper and the return of cyanide bound in complex compounds for leaching process is an optimal way of solving the problem of gold-bearing copper ores treatment. By using the technology, an adverse impact onto gold recovery process is eliminated and at the same time reducing the cyanide consumption. Today, processes and methods of high-grade copper leaching solutions conditioning before and after gold recovery have been developed, which combine two ways of copper recovery: as a saleable product and cyanide to recover gold and reduce total operating costs. They are Cutech, MNR, SART, Cyanomet, AuGment, Vitrokele, Hannah and Cyanisorb. At the same time, these technologies have not been studied enough and described in literature. Data on parameters and operating conditions as well as introduction is not available. The conditioning technology of recycled solutions developed by IRGIREDMET JSC allows copper to be recovered as high quality concentrate and at the same time free cyanide regeneration in the recycled solution which is amenable to gold leaching. This technology was commercialized at a mine in Kazakhstan in 2008. The removal and recycling of cyanide does not require additional cyanide and is cost-effective. More cost-efficiency is achievable through selling copper concentrates, closed water cycle without the detoxification of effluents and enhanced gold recovery by CIL and cathode quality.

Sep 1, 2012

By Z. H. Xu

Flotation as a versatile multiphase separation technology has been practiced for more than 100 years in coal and mineral processing. Although effective over a wide particle size range, flotation for mineral separation has been largely understood as an art rather than a science, treating the flotation system as a black box. With rapid progresses in microscopic technologies coupled with high speed video recording and imaging analysis, ingénue design of visualization systems has made it possible to understand fundamentals of flotation by visualization. In this presentation, the state of the art where visualization plays a key role in advancing our fundamental knowledge of flotation will be reviewed. The areas to be covered include characterization of bubbles (shape, size, velocity and sol-ids loading) in a running flotation system, either column or mechanical cell, bubble-solid attachment, hydrodynamic cavitation in fine particle aggregation and flotation, froth imaging, particle-particle interactions by zeta potential distribution measurements, and heterogeneous gas nucleation by atomic force microscope imaging. With these capabilities, critical roles, good or bad, of ore proper-ties, solution chemistry, slurry hydrodynamics, and operation variables in flotation systems as applied to mineral, coal and oil sands processing were clearly elucidated.

Jan 1, 2014

By Sergey S. Gudkov

In the current climate of changing the approach to mining and treatment of mineral resources, processing technologies are being developed that require little maintenance and are economically as well as ecologically sustainable. This may also involve the development of entirely new ways of ore processing. One promising approach is to use bioleaching for the pretreatment of gold refractory ores to cyanidation. Capital costs for vat bioleaching of concentrates and ores are very high and cannot be applied for small or medium-size deposits. IRGIREDMET JSC carried out bio heap leaching test work on refractory ore samples from three Russian deposits. Following this biological treatment a combination of flotation, vat bioleaching, and cyanidation are used to recover gold. After heap bioleaching, gold recovery was 75-80 per cent. It was found that efficiency of heap bioleaching process depends on ore feed size. High duration of this process is another feature and it lasts for about a year. This process can be also used for carbonates in the combination with other process during which acid generation occurs. The results of our studies have shown that this technology is amenable for refractory gold ores. Its introduction allows an increase gold recovery and to solve a number of environmental problems. Keywords: heap biooxidaton, the refractory of the ores, the degree of oxidation, arsenopyrite, pyrite, CIL

Sep 1, 2012

By C. Y. Wang

Anodic reaction mechanism of complicated antimony-lead concentrate in Slurry Electrolysis has been investigated by the anodic polarization curves determined under various conditions. The main reactions on the anode are the oxidation of FeCln (2-n), though the oxidation of jamesonite particle on the anode can occur during the whole process, it is less. With the help of mineralogy study and relevant tests, the leaching reaction mechanism of jamesonite and gudmundite during Slurry Electroly-sis has been ascertained also. Because of the oxidation reaction of FeCl3 produced by antimony-lead concentrate itself, the non-oxidation complex acid dissolution of jamesonite, the oxidation complex acid dissolution of gudmundite, and the oxidation of air carried by stirring, the leaching ratio of antimony reaches to about 35% when using HCl-NH4Cl solution to leach antimony-lead concentrate directly. So given the theoretical electric quantity, which to oxide antimony in Slurry Electrolysis, all of antimony, lead and iron, which contained in antimony-lead concentrate, are leached.

Jan 1, 2014

By Zhen Hu, Chenghang Wang, Jianjian Zou, Xiujuan Li, Hanwen Li, Tai Wang, Baoxu Song

A rare earth deposit in Sichuan, China is rich in wulfenite in addition to bastnaesite and barite, and the deposit has already adopted high intensity magnetic separation technique to pre-enrich the rare earth minerals, during which the wulfenite and barite have been left in the non-magnetic product. Because the chemical composition of wulfenite is only 24.17% Mo and 42.15% Pb, it is very hard to obtain qualified lead or molybdenum concentrates by physical separation process. To pre-concentrate the wulfenite, flotation has been first introduced, and by using 100g/t GY-7 as dispersant, 1500g/t CP-1 as depressant and 160g/t GY-4 as collector, a floatation concentrate assaying 15.52% Mo with a recovery of 86.12% was obtained. Then a leaching process was conducted by using 1.2mol/L Na2S as leaching agent, and molybdenum can be translated into sodium molybdate in the solution with a leaching recovery of 99%. To recover rare earth oxides (REO) and lead from the leaching residue, a magnetic separation process has been conducted. Above all, by the whole process, the molybdenum recovery reaches 86.16% in the sodium molybdate solution, and a lead concentrate assaying 54.59% Pb with recovery of 27.99% could be obtained.

Jan 1, 2014