Search Documents

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching and anodic-polarization experiments showed that coexistence of cupric and ferrous ions activate anodic dissolution of chalcopyrite, causing faster copper extraction at the potentials below a certain value (critical potential). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials. These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model.

Jan 1, 2003

By Çisem Tuba, Ismail Girgin

"Comparative atmospheric H2SO4 and H2SO4 + H2O2 leaching experiments were performed using a Turkish lateritic nickel ore containing 1.52% Ni. In the leaching tests; acid concentration, temperature and leaching time were considered as main variables and the dissolution behaviour of the ore were studied by Ni, Fe, Co and Mg analyses. The dissolution values in the H2SO4 leaching experiments were observed to increase up to 60% (w/w) acid concentration and a temperature of 95°C. Increase of H2SO4 concentration above 60% at 95°C caused decreases in all the dissolution values and this was attributed to the formation of Fe2(SO4)3 and Fe2(SO4)3•HSO4•H2O type compounds. At the considered optimum H2SO4 leaching conditions ([H2SO4]= 45%, T=95°C, t=45 min); dissolution values reached for Mg, Ni, Fe and Co were determined as 99.12%, 95.58%, 92.63% and 78.37%, respectively. An activation energy of 30.57 kJ/mole was determined for nickel dissolution from the evaluation of the kinetic data obtained for H2SO4 leaching showing that the dissolution was controlled by external diffusion and chemical reactions. Caro’s acid solutions were prepared at H2SO4/H2O2 mole ratio of 3 for varying initial H2SO4 concentrations and leaching tests were performed at 25°C. Co behaved very differently and a dissolution value of 83.94% was obtained even at 5% acid concentration in 60 minutes reaction time. Complete dissolution of Co was obtained after 30 minutes of reaction time at 60% initial H2SO4 concentration and the corresponding dissolution values for Mg, Ni, and Fe were reached to 96.16%, 94.27% and 89.46%, respectively. Although the H2SO4 + H2O2 leaching experiments were conducted at 25°C, it was realized that the temperature of the leaching medium was increased to 122°C after four minutes of reaction time due to probable exothermic reaction(s) at 60% initial acid concentration."

Jan 1, 2014

The flotation of nickel sulphide minerals is normally difficult in the presence of serpentine minerals due to the coating of serpentine particles on the nickel mineral surface. To improve the flotation, dispersants such as polyphosphate and carboxy methyl cellulose are normally used to remove the slime coating. However, in the flotation using high ionic strength process water, these dispersants are invalid due to their ionic nature. In this study, a new type of non-ionic dispersants, Pluronic triblock copolymers were examined with an objective of improving the flotation of ultrafine pentlandite (a nickel sulphide mineral) in the presence of lizardite (a serpentine mineral) in saline water. Three Pluronic triblock copolymers varying in solubility and hydrophile-lipophile balance (HLB) values were studied by flotation tests, settling tests and froth measurement. It was found that two of the copolymers improved pentlandite flotation against lizardite, and one copolymer deteriorated the flotation. The effect of Pluronic triblock copolymers on the flotation was actually linked to their dispersibility and foamability, which were governed by their physical properties. The two copolymers with a higher solubility or HLB value produced more stable mineral suspensions and more stable froth in the flotation resulting in better nickel grade and recovery in both rougher and cleaner flotation. Keywords: ultrafine particle, flotation, slime coating, dispersion, saline water, triblock copolymers

Sep 1, 2012

By Yang Xiao, Zhang Yimin, Bao Shenxu, Liu Chun

Stone coal is a unique vanadium-bearing resource in China. Many techniques, such as salt roasting-water leaching, blank roasting-acid leaching, direct acid leaching etc. have been developed for vanadium extraction from stone coal. The vanadium leaching rate can reach 74.9% for stone coal from Jiangxi, but only about 27% of vanadium is leached for Hubei ore by applying salt roasting-water leaching technique. This paper investigats the vanadium occurrence in stone coal by microscope observation and electron probe, and compares the minerals components of stone coal from Jiangxi and Hubei. Although most vanadium exist as an isomorphism by replacing Al(III) from dioctahedral structure in mica group minerals in stone coal from two regions, the free vanadium is remarkably abundant in Jiangxi stone coal than in Hubei stone coal, which results the fact that vandium is relatively readily extracted from former. Moreover, the content of calcite in Hubei stone coal is much higher than that in Jiangxi stone coal. Calcium can react with V2O5 to form water insoluble calcium vanadates during roasting and this may be the reasone why the water leaching rate of vanadium is low for Hubei ore. Acid leaching is more beneficial to the vanadium leaching but other extra methods, such as adding aid-leaching agent and/or increasing acid concentration is need for the ore where vanadium is embeded firmly. This study can effectively guide the selection of vanadium extraction techniques for stone coal from different regions.

Jan 1, 2014

By Peter Ay, Elena Geldt, Satyanarayana Narra, Claudia Glaser

"As part of an extensive research and development project, the technical and technological implementation of the patents DE 10 358 245 B4 and WO/2006/056172 was developed with the goal to present a system for the innovative roll- agglomeration method exhibiting a) a modular setup, b) high productivity and c) suitability for the use of fibres of different applications and product qualities (high technical availability). The processability of the rarely adapted raw fibre materials into high-value intermediates brings forward their application in various processing industries dealing with the production of fibre reinforced plastic composites, heat and sound insulation materials as well as with the gas and liquid cleaning systems. The innovative fibre agglomeration presented in this work is performed by a combination of rolling and pressing the fibres inside a geometrically pre-defined roller table, in which the fibres are forced to bound through entanglement / interlocking and develop into agglomerate. The agglomeration process is carried out in a circular roller path with a rectangular cross-section. For improving the adhesive properties, and thus the quality of the agglomerates, the boundary surfaces can be covered / patterned / lined / coated with various materials. The resulting roll-agglomerates are characterized by different quality parameters such as mass, shape, porosity and stability. The properties of the agglomerates can be modified based on the end-product requirements by slightly modifying the process parameters such as filling ratio, residence time, roll-geometry, procurement of the boundary surfaces, etc. as well as the input material properties such as fibre type, fibre fineness, fibre length, etc. This work carries extensive work on the roll-agglomeration system to assess the effectiveness and the variability based on the product specifications. Agglomerates were produced with wide variations of system parameters with varying roller table liners and based on evaluation of the produced agglomerates with respect to their mass, the geometrical dimensions, their porosity and stability."

Jan 1, 2014

By C. S. Gundewar

About 90% of the barytes produced the world over is used for oil and gas drilling as weighting agent in drilling mud to control pressure, prevent blow out and provide lubrication. This is because of its unique properties like high specific gravity, water insolubility and intentness. India is one of the leading producers and exporters of barites. The Mangampeth Baryte deposit in Cuddapah district of Andhra Pradesh, India being the largest single deposit in the world having a reserves of about 80 million tonnes. Approximately 50% of the total reserves of grey barites of Mangampet deposit assays less than 92% BaSO4, the minimum stipulated grade for oil and gas drilling industries. To reach and recover the high grade barite, the overlying low grade has necessarily to be mined out and removed. At present this is being stacked separately at the mine site involving lot of labour and transport cost. Considerable barites is contained in the dumps adversely affecting the conservation and creating lot of environmental hazards. IBM being the premier organization in India in the field of conservation of minerals and environmental protection in mining has recognized the importance of adverse effect of these huge dumps at site. The Ore Dressing Division of IBM, Nagpur has characterized these dumps and developed the flotation process on a sample assaying 66% BaSO4 and 23.3% SiO2. The flotation concentrate obtained assayed 93.7% BaSO4, 2.38% SiO2 with BaSO4 recovery of 80% and meets the requirement of the oil industry. The flotation concentrate being non-wetable, can not be used as such as weighting agent, and hence the collector coating on the concentrate was removed either by acid treatment or heating to make it water wetable. The concentrate was 92% -325 mesh and having a specific gravity 4.3. The barites concentrates so produced meets the size, grade and specific gravity specifications required for use in oil drilling industry. Apart from the financial benefits the process augurs well for the commercial exploitation of these huge dumps in terms of (1) additional recovery of these valuable minerals and conservation, (2) reduction in dumps value, (3) improvement in environment and offering an excellent potential for export.

Jan 1, 2014

By Hajime Miki, Mutia Dewi Yuniati, Tsuyoshi Hirajima, Keiko Sasaki

Acid mine drainage is mainly due to pyrite/arsenopyrite oxidation processes, and suppressing such processes is important issue. As a promising process it is reported that silicate ion can complex with catechol (1,2-dihydroxybenzene) and this complex is oxidized to a solid silica layer on the surface of those sulphide minerals. Detailed behavior was investigated from the result of electrochemical experiments. Results of polarization potential showed that oxidation peak can be seen only in the presence of both silicate ion and catechol addition at this peak potential and this peak can be identified as silicate-catechol complex oxidation to silica. Potentiostatic experiments indicated the dissolution kinetics of pyrite. Untreated pyrite dissolution rates were higher than pyrite treated with catechol and silica solution. To enhance the silica layer reaction on pyrite, the pyrite potential was held at 550 mV vs. SHE in catechol silica solution. This pyrite dissolution kinetics was almost the same as untreated pyrite. Potential hold followed by drying for 30 min process resulted in much lower pyrite dissolution rates. Drying is important for development of the silica layer. Analysis of this potentiostatic curve provided a way to estimate the thickness of the produced silica layer and kinetic information of treated/untreated pyrite. Untreated pyrite showed thinner initial layer thickness on the surface of pyrite (oxidized passive layer, not silica) and higher oxidative kinetics of pyrite compared with silica-coated pyrite.

Jan 1, 2014

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

Although the cyanidation process for gold leaching has been applied for more than a hundred years, some aspects of it, such as the passivation of the gold and the depassivating action of heavy metals, are still not well understood. In this work the anodic behaviour and surface composition of gold in alkaline aqueous cyanide with lead additions were investigated using polarization experiments and XPS. It was found that lead in the solution activated the gold at low concentrations, somewhat more positive than the reversible potential for gold, but that the activity again decreased at higher concentrations of lead. The potential range for the activation of the gold coincides with that where underpotential deposition of lead occurs, i.e. –200 to –600 mV(SCE), as indicated by the surface composition of the gold, shown in figure 1. Note that the concentration of lead on the surface of the gold only increased with time in the bulk plating potential range for lead, where gold is not activated by the presence of lead. It is also shown that up to 20 mg/L of lead added to the solution will activate the gold, provided that bulk plating of the lead is avoided. It is also important to avoid reducing conditions during leaching, where bulk plating of lead may occur, if the gold is to be activated by lead to achieve a high leaching rate, as the bulk plated lead screens the surface rather than activating it.

Jan 1, 2003

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By F. H. Wang

The Yinmao Lead-Zinc Mine Co. Ltd. has got 50 years of mining history. In recent years, the manganese grade in the flotation tailings has been continuously increasing. In order to make fuller use of the existing resources, as well as to increase the company?s economic efficiency, our company adopted the technique ?magnetic separation? and ?iron removal? to effectively recycle the manganese concentrate resources.

Jan 1, 2014

By S. M. Viduka

This paper presents a numerical investigation of solid separation in jigging device, which is a gravity separation method widely used in ore processing. Separation is recognized as being heavily dependent on fluid motion in the jig. This study explores the effects of the inlet time dependent velocity profile on jigging performance. Modelling of the liquid-solid system is performed through a combination of computational fluid dynamics (CFD) to simulate liquid flow and discrete element method (DEM) to resolve particle motion. The initial packing conditions consist of a binary-density particle system of 1130 particles each 1 cm in diameter. A variety of jigging profiles are implemented in jigging. The saw tooth pulsation profile is selected with three variations in both amplitude and frequency. The performance of each profile variant is compared in terms of solid flow patterns, separation kinetics, energy, and mean particle position. These quantitative comparisons demonstrate significant differences in the segregation rate, energy, and solid phenomena, helping find an alternative optimum operating setting for the system.

Sep 1, 2012

By Ho-Seok Jeon

The separation in gravity concentrators is based on the density difference between valuable and gangue minerals. In addition to density, many auxiliary parameters like particle size, shape, feed rate, pulp density etc. plays an important role in the separation. The performance efficiency of gravity units is largely based on the interference of such auxiliary parameters during separation. Many gravity concentrators are used for the beneficiation of cassiterite ores and performance of which are varying with different feed material, particle size and required enrichment from the unit. Selection of gravity units is generally based on laboratory testing and data collected from the previous experience. In the present investigation cassiterite ore collected from Uljin deposit, South Korea has been subjected to various gravity units like jig, spiral, and Knelson concentrator with the intension to pre-concentrate the ore. Second stage concentration was carried out using shaking tables. The article mainly summarizes performance evaluation methods employed for gravity concentrators. Selection of gravity circuit for the beneficiation of cassiterite was made on the basis of the recovery-grade curve, and Tromp curve methods. Keywords: cassiterite, gravity concentration, recovery-grade curve, sink-float test, tromp curve

Sep 1, 2012

By L. Stamenov, H. Bouzahzah, S. Gaydardzhiev, D. Naumov

"The Chelopech epithermal arsenic bearing high-sulphidation, copper-gold deposit located in Bulgaria is often referred as the richest European gold deposit currently under exploitation. Key points from the flotation circuit of the processing plant have been sampled and selected physicochemical parameters measured. Plant survey has followed with selected samples being submitted to chemical and mineral liberation analysis (MLA). Quantitative analysis has enabled to link the flotation response of the main copper bearing minerals with the physiochemical parameters (Eh, DO, EDTA extractable Cu and Fe) being measured. Data from mineral liberation analysis have highlighted an important process-relevant information explaining the variable floatability in the various granulometric classes.The low chalcopyrite recovery could be linked to the non-sufficient amount of dissolved oxygen measured in the copper selective flotation circuit. Given the finely-disseminated copper bearing minerals, the observed copper losses inside the flotation could be also explained by the insufficient degree of liberation of the mineral grains. Suggestions for improvement in metallurgical recovery are therefore proposed.INTRODUCTIONThe Chelopech deposit is a high sulphidation (HS) volcanic-hosted epithermal gold-copper one (Bonev et al., 2002; Kouzmanov et al, 2009; Strashimirov, et al. 2002). It is considered as one of the largest and economically most important ore deposits in Bulgaria, and often is referred to Europe’s largest currently mined gold resource. It is located in the Srednogorie zone which falls within the central sector of the extensive Tethyan–Eurasian copper belt formed during Mesozoic–Cenozoic time along the southern margin of Eurasia. The Srednogorie zone has the features of a subduction-related, Late Cretaceous island arc, with development of a calk-alkaline to sub-alkaline volcano-plutonic magmatism and associated hydrothermal ore deposits (Bonev et al., 2002).Ore mineralisation occurs as veins, mineralised breccia, and massive sulphide replacements and disseminations. Three mineralisation stages have been identified at Chelopech deposit. An early pyrite–marcasite mineralisation (stage I), characterised by disseminated to massive pyrite followed and partly brecciated by enargite– luzonite and tennantite–chalcopyrite–bornite (stage II) mineralisation. The gold is met in ores belonging to the stage II. Sphalerite and galena veins characterise stage III, best developed below and adjacent to the pyrite–enargite– chalcopyrite ore bodies. Advanced argillic altered volcanoclastic rocks commonly host this mineralisation (Chambefort and R. Moritz, 2014)."

Jan 1, 2018

By Qidong Zhang, Yongsheng Song, Wenjuan Li, Guiying Zhou, Kun Song

"Molybdenum is a very important rare mineral resources, which exists largely in oxidized ores and sulphide ores in nature. About 99% of metallic molybdenum comes from molybdenite. The talcose molybdenum resources are abundant but the resources utilization is low, because the talc is naturally hydrophobic and the floatability of talc is similar with molybdenite, which lead to difficult separation by flotation. Talc is easy entry into concentrate in flotation which can cause the content of MgO overhigh, therefore the molybdenum concentrate grade can not meet the industrial requirements. Thus the utilization level of talcose molybdenum resources has been restricted greatly.The adsorption of water on talc and molybdenite surfaces and natural floatability of minerals were studied by density functional theory method. The results showed that molybdenite and talc were layered minerals which exhibited similar surface wettability and H2O molecule prefers to stay with water rather than the minerals surfaces. N2 is adsorbed on talc and molybdenite surfaces more easily than H2O. The interaction and flotation behavior were studied by SEM and flotation experiments. The reason why talc interferes with the flotation molybdenite has been revealed. The agglomeration between molybenite and talc was caused easily in neutral or acidity solution, and it was dispersing between molybenite and talc particles in alkaline solution. The flotation results showed that good floatability of talc was the key factor causing a low grade of concentrate in alkaline solution. Thus, it is the key factor to enlarge floatability difference between molybdenite and talc.INTRODUCTIONMolybdenum is a kind of important rare metal and strategic reserve resources (Zhitao Y et al, 2016a). Due to excellent characteristic, such as high melting point, good thermal property and et al, it’s widely used in metallurgy, machinery, chemical, aerospace, and many other areas. It has become an indispensable metal in modern industry. Molybdenum generally exist in the form of molybdenite which is a kind of mineral with excellent natural floatability. Talc is a kind of typical hydrous and layered magnesium silicate minerals (Beattie D et al,2006a), which is one of the most common gangue mineral of the platinum group metal ores and metal sulfide ores (Tao L et al,2011). Due to its good native floatability, talc is easy entry into the concentrate product with foam in the process of sulfide ore flotation (Kelebek S and Smith S, 2006b), which resulted in decreasing concentrate indexes. Not on that, the high-content MgO of concentrate will also produce a series of adverse impact to the subsequent smelting (Lotter N O et al, 2008). Therefore, it is difficult to separate talc from sulfide ore concentrate effectively."

Jan 1, 2018

By Ari Kokko

Metso has a long history supplying boilers for high ash coal firing. These boilers are based on circulating fluidized bed (CFB) technology. CFB?s biggest benefit is fuel flexibility ? it can burn fuels from high moisture content to high ash content. Metso has delivered tens of CFB boilers burning waste or high ash coal starting on 80?s. Some of the boilers have been in operation twenty years meaning that there is a long term experience from these plants available. This feedback includes boiler performance and maintenance issues of the boiler. Metso is also delivering coal washing plants to improve coal quality, i.e. reducing ash content of the coal. The idea to combine coal washing plant and CFB boiler was made up two years ago in Metso. Up-coming legislation of coal washing and restrictions for washery reject land-filling in India are good drivers for this kind of concept. Pre-study of this kind of concept led to the conclusion that coal washing process can be fine-tuned so that reject?s calorific value is only 1100 kcal/kg and that was set as a target for boiler design. Metso shipped 200 tons of washery reject to its own research center located in Tampere Finland. First a wide range of fuel characterization tests were done in lab-scale and after that one week test run in 4 MW CFB pilot boiler was done. Test run proved that 1100 kcal/kg can be fired without any support fuel with special boiler design. Test run results gave a good set of data regarding combustion efficiency, emission performance and boiler dynamic behaviour when burning this kind of fuel. These results are introduced in this paper. This paper introduces also the CFB boiler concept for washery reject firing including boiler plant, fuel and ash handling systems and flue gas cleaning system. Power plant can be integrated with coal washing plant so that boiler size matches with washing plants c

Sep 1, 2012

By Bern Klein, Givemore Sakuhuni

Flotation is the dominant base metal extraction technique and it requires ore to be ground below the liberation size for effective recovery due to its dependence on mineral surface properties. For a poly-metallic ore, differential hardness of constituent minerals leads to over grinding of softer minerals before the harder minerals are fully liberated, which makes selection of a target grind size complex, and the complexity increases when treating leaner ores. Flotation recovery deteriorates above 100 and below 10 microns causing significant loses of valuable minerals in most flotation circuits. Although enhanced gravity concentration is known to be effective at recovering particles above 100 microns, which are difficult to hydro-dynamically transport, exploiting differential specific gravity for base metal separation was not an option in the past. This was partly due to the absence of high mass yield gravity techniques. The advent of continuous gravity concentrators with flexible mass yields, in the past two decades, has necessitated investigation of possible base metal applications. The Knelson CVD, one of the continuous discharge centrifugal concentrators, has an established application niche for sulphides associated with gold. However, its base metal applications have never been rigorously tested. Considering the dependence of flotation recovery on particle size, continuous discharge centrifugal concentration can be integrated in flotation circuits to capture flotation non-recoverable coarse particles. This paper explores how particle size, liberation and mineral hardness influence application of continuous centrifugal technology to regulate galena deportment in a polymetallic base metal plant. The results show that particle size affects galena recovery more than liberation. In view of these results, the CVD can be integrated in the primary grinding circuit to pre-concentrate the heavy sulphides at a coarser grind size with potential grinding energy savings.

Jan 1, 2014

By Shobha Kumari

Coal is the prime source of energy in India. It now contributes to about 55% of the total power generation and will continue to have its major share in the energy mix of the country in the foreseeable future. Thermal coals of India, known for their wide variations in nature and categorized as difficult to wash due to their typical mineral matter association with the organic matrix, need suitable beneficiation technique for quality upgrade for improving the overall economics, efficiency and pollution free power generation. A non-coking high-ash coal, collected from Vasundhara open cast mine of the Ib Valley Coalfield, Orissa, has been characterized along with its different fractions obtained in the process of beneficiation for distribution of minerals using FTIR, XRD and ash analysis. The raw coal was fractionated by size as well as by density. It has been observed that ash yields and mineralogical composition (found to be mainly kaolinite and quartz) have no appreciable change in different size fractions, indicating homogeneous distribution of minerals in the coal matrix. However, for the different density fractions the mineral composition and ash yield have significant variations. The quartz content of the beneficiated coal visualized with 34% ash yield, as mandated by the Ministry of Environment and Forest (MOEF) for the use of coal in power plants is reduced to half of that of the raw coal. As quartz is the most abrasive mineral in coal, reduction of its proportion obviously signifies considerable reduction of wear of power plant machinery when beneficiated coal is fed to utility boiler for generation of power. The composition of the major minerals quartz and kaolinite as determined, also favors formation of ash of refractory nature during combustion. Keywords: IB valley coal, beneficiation characteristics,

Sep 1, 2012

By Jacek Kolacz

"Comex has carried out an extensive research work related to optimising sensor based sorting systems. The main target was to achieve efficient separation and maintain high capacity of the process. Eventually, the operating cost of the sorting process was investigated in terms of potential industrial applications and possible replacement of the existing traditional processing equipment. The study included an influence of the following factors on the separation efficiency: capacity, particle size and distribution, particle shape, material properties like colour, density and composition, as well as percentage of the rejected fraction. The above factors were also considered in the calculation models for the operating cost of the sorting process. In addition, other elements were considered like compressed air cost, cost of energy, labour cost, and necessary service and maintenance cost. All these elements were implemented into the calculation model allowing quick and effective evaluation of the major parameters for sorting applications. Finally, the study was carried out for two popular sorting principles: visible light sorting utilising differences in color, texture and shape and X-ray sorting using differences in density and chemical composition. GENERAL INFORMATION ABOUT SORTING POSSIBILITIES Application of the sensor based sorting systems, without any doubt, brings a lot of possible advantages in many mineral operations. The main advantage of the new system is related to its universality and at the same time very sophisticated image processing functions, which can be carried out in the same processing unit (Kolacz, 2014). Figure 1 shows the CXR-1000 system from Comex with 1 m belt width, in the configuration where many different analysed parameters can be used to provide particle separation. The image analysis system includes a camera installed either over the transport belt conveyor or at its discharge end. The system includes the X-ray attenuation analysis realized by the XRT system in the central part of the conveyor belt. The sorting system can be used with both optical and XRT analysis or separately depending on an application."

Jan 1, 2018

By I. Gombköto

To sustain the growth of industrial production necessitates the increasing of the amount of processed mined raw and secondary materials. As a side effect of raw material production, the amount of tailings material, - coming from mineral processing operations ? increases as well. Using wet technology, these tailing materials are generally transported and stored with the water used for previous operations. This habit could lead to dangerous situations. Enough to remember the disasters had happened to the last decade, safe tailings operations need to remove as much water from the solid as possible. Environmental, technical and economical needs should meet, therefore using a technology combining these specific needs could be necessary. Paste technology was introduced generally into tailings operations at the last ten years, as an answer to the call of the above mentioned challenges, however there are still many questions to answer within the frame of using it. The Institute of Raw Materials Processing and Environmental Process Engineering of the University of Miskolc has been dealing with mechanical process engineering, especially by the support of the EU project TAILSAFE Contract nº EVG1-CT-2002-0066 and the NKFP 3A/068/2004 Hungarian fund extensive research has been carried out about paste technology. Different test methods and materials were applied. Tested tailings materials were as follows: different fly ashes from coal power plants from Pécs ? Hungary, Gyöngyös ? Hungary, Neyvil ? India, different Croatian ashes, hazardous waste incineration plant ashes from Dorog ? Hungary, different kind of sands from Hungary, fine glass sand from Fehérvárcsúrgó ? Hungary, flotation ore processing tailing from Gyöngyösoroszi ? Hungary. Different additives, as gypsum, bentonite and cement were tested as well. The applied test methods were as follows: physical material testing (laser sizer, piknometer, different microscopes), X-ray diffraction analysis, settling columns, the three measuring pipes tube viscometer (16~27 mm pipe diameter), a hydraulic test loop with different pumps (40~53 mm pipe diameter, 0.2~4 m/s average slurry velocity range, 0%~52 % volumetric concentration range), rotational viscometer, Cassagrande yield locus tester and the slump cone test. This paper summarizes and systematizes the results of the aforementioned research as well as reports about the developed paste pipe transport design method based on the fine suspension ? coarse mixture model. The paper also reports about a systematic experimental series with different materials to establish criteria when high concentration suspensions behave like paste.

Jan 1, 2014

By Liu Jie

Refractory iron ore deposits in China have various genesis and complicated types, the nature of which is poor, fine-disseminated and complex. Therefore, refractory iron ore could scarcely be separated and utilized by traditional mineral processing technology at present. It is necessary to explore deep reduction technology to change the characteristics of refractory iron ore and to use effectively the iron resource. And deep reduction technology is that on the condition of higher reduction temperature than that of magnetic roasting and stronger reducing atmosphere, the iron oxides from iron ore was reduced to metallic iron particle that is easy to dissociate. And then production from deep reduction is easily separated by magnetic separation and iron powder production was obtained finally. Deep reduction technology for Lingyang iron ore from Jilin, China, as the refractory iron ore, was studied in this paper. The influences of such main factors as reduction temperature, time and coal content were investigated. The results showed that the Metallization rate of reduction product was up to more than 90% under optimum conditions, and then higher iron grade and recovery of reduction iron powder were obtained from subsequent magnetic separation. Furthermore, the deep reduction mechanism in the system was studied by the means of XRD and SEM analysis for reduction production and Physical Chemistry of Metallurgy. Analytical results indicated that during deep reduction, the size of iron particle from deep reduction materials was increasing as reduction temperature rising and reduction time extending. The growth of metallic iron particle from deep reduction production was divided into such three stages as reduction nucleation, deep reduction and growth of metallic iron particle.

Sep 1, 2012