Search Documents

By I. Y. Titov, Victor D. Samyguin, A. Y. Nikitin

"It is suggested that improvement of separation process efficiency in machines and circuits of selective flotation should be based on application of the principle of technology individualization (PIT). This principle is grounded on the following provisions.The mineral composition of ores is used to establish the correlation between the selective reagent mode and the individual value of hydrodynamic conditions of flotation machines together with individual structure of the process flow diagram. The individuality of all sorts of particles identified by methods of process mineralogy was characterized by their distribution according to the rate of flotation (or spectrum). The spectrum identification is carried out by modeling and by experimental and computational method on the data obtained on various types of laboratory flotation machines.The computer-aided test is used to determine the optimal fraction distribution, which reaches the highest possible level of concentration data. The direction of hydrodynamic factors action on concentration data is estimated based on comparison of design base and experimental spectrum. The improvement of separation efficiency in devices is achieved in special-purpose flotation machines (SFM) the design of which provides optimization of hydrodynamic regime in spatially isolated zones. It is demonstrated that the main parameter of SFM operating mode individualization is the rise rate of bubbles going from the chamber into the froth. During this time the composition of particles optimum for separation is formed on its surface. Additionally, it is necessary to coordinate in the zones the residence time of pulp and foam streams with the air consumption. The improvement of separation efficiency in flotation process flow diagrams may be achieved by making several cascades with SFM installed in them. The individual effective structure of the scheme for a definite ores material composition depends on the ratio of particle varieties in the spectrum and is revealed by modeling."

Jan 1, 2018

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By U. Dmitrakova, G. Sedelnikova, D. Kim, E. Savari

"The paper presents the results of research on the development of gold and silver extraction technology from refractory gold sulphide flotation concentrate of one deposits of Nord-East of Russia. The concentrate is due to the complex mineral composition. Gold and silver are finely disseminated in sulphide minerals (arsenopyrite and pyrite partially oxidized by 7-11%). These are characterized by high content of silver 219 g/t and sulphide sulfur 32%, the presence of poorly soluble silver minerals (silver sulfosalts, fahlore, finely dispersed hypergenic acanthite in iron hydroxides and jarosite, etc.), and impurity minerals capable of interacting with cyanide (pyrrhotite, marcasite, nonferrous sulphides) and causing higher than normal cyanide consumption. Pretreatment of refractory sulphide concentrate by biooxidation using a mixed association of mesophilic and moderately thermophilic bacteria at a temperature of 36-40 °C for 120 hours oxidized arsenopyrite by 97.5%, pyrite by 93.5%, unlocked refractory gold, and generally oxidized the minerals absorbing cyanide and oxygen before cyanidation. Further oxidation of these minerals-absorbents was facilitated by the aeration in calcareous medium of the solid biooxidation residues of the concentrate. Sorption cyanidation of the solid biooxidation residues with addition of lead (II) of recovered 91.2% of gold and 82.9% silver from biooxidation residue, compared with 80.1% and 46.6%, respectively, for sorption cyanidation without the preceding biooxidation step. Biooxidation of the concentrate prior to cyanidation improves the recovery of precious metals, especially silver, and significantly reduces cyanide consumption from 18.7 kg/t to 3-5 kg/t of concentrate. INTRODUCTION Biooxidation of gold sulphide concentrates using acidophilic microorganisms has been successfully applied worldwide (van Aswegen et al., 2007; Gericke et al., 2009; Sovmen et al., 2007; Sovmen et al., 2009). At least 15 full-scale plants for tank biooxidation of sulphide concentrates are presently in operation, and the construction of new ones is planned (Bulaev et al, 2015)."

Jan 1, 2018

The objective of the paper is to develop a material balance calculation procedure for a production unit involving two plants separated by a pipeline. The case study is taken from the oil sands industry. The raw sands are first mixed with water in a conditioning plant, then transported through a pipeline to an oil extraction plant. The combination of pipeline dimensions and nominal throughput creates a significant variable time lag between the two plants. As usual, mass balance calculations required for the evaluation of plant performance indicators, such as bitumen recovery, are inaccurate due to measurement errors. In addition, in the present case study, the time lag of the pipe creates an additional source of uncertainty, which may lead to misinterpretations and wrong decisions. Raw data are usually reconciled through steady-state mass balancing, to correct for measurement errors. However, because of the significant pipeline dynamic lag, standard steady-state daily mass balance may fail at giving an appropriate picture of the operations. The proposed solution to the data reconciliation problem includes the use of a pipeline plug-flow model in the mass balance calculation. To fulfil the industrial constraint that current data reconciliation must not modify past reconciled values, while still satisfying dynamic constraints, a daily one-step method, i.e. a unitary filter-ing horizon, is recommended. The method is illustrated with simulation data, and the results com-pared to those of standard data reconciliation methods.

Jan 1, 2014

By Ö. Genç

In this paper, full-scale mill data collected from three different circuit configurations in cement plants demonstrated the size reduction performance of dry ball mills in relation with the ball size classification achieved by the classifying liners used in the grinding compartments. Findings indicated that, breakage rates at the last 2 ~ 4 meters of the mill are not sufficient to give reasonable size reduction ratios for the production of fines. Application of only damming rings without classifying liners resulted in inverse ball size classification which lead to reduction in size reduction performance thus specific breakage rates.

Jan 1, 2014

By S. P. Nagaeva, O. U. Poperechnikova, A. V. Kuptcova

"In case of free gold presence in ore, there is always problem of a choice between the gravity-flotation and gravity separation flowsheets. Study of morphology of gold being extracted by different methods allows to find the most efficient solution. One of the latest methods of gold concentration for wide range of grain size (-0.8+0 mm) is a flash flotation. The paper presents comparative testing results of flash and centrifugal separation.The goal of the studies was to determine process and flotation parameters of flash flotation. In case valued minerals are soft if compared to host rock, such minerals tend to concentrate into circulating load of grinding circuit. Thus, valued minerals can be overground, and in turn, will result in low extraction in flotation circuit. Integration of flash flotation operation into process flowsheet has been evaluated. Flash flotation operation can be successfully used not only for gold but also copper, lead, nickel and silver minerals.With low-sulphide ores being a case study under laboratory conditions, various flotation (impeller rotational speed, air flowrate) and process (pulp density, collector consumption, frother consumption, time of flotation) parameters were studied in view of its impact on gold flash flotation. Experiments were carried out under laboratory conditions using special pneumatic mechanical flotation machines.INTRODUCTIONGravity separation is used for extraction of coarse gold before cyanidation and before flotation of polymetallic ores to increase gold total recovery into gravity copper and lead concentrates.Benefit of the flash flotation is efficient recovery of coarse gold carrier particles (sulphides) thus preventing its regrinding and, as a result, low recovery. Furthermore, combination of flash and conventional flotation results in final tailings that do not require further cyanidation.Combined gravity-flotation flowsheets are designed for concentration of ores containing gold within thewide range of grain sizes (see Table 1)."

Jan 1, 2018

By A. P. Purgin, M. G. Viduetsky, I. F. Garifulin

"The combined treatment process for mine, tailings storage facility, quarry, circulating, and waste water in the mining and metals industry brings together the conventional chemical treatment processes and pneumatic flotation cells of the KFM series. The key principle of the process is preparing the water for treatment by saturating with finely dispersed air bubbles in the flotation cell blowers. Gas-air lift dispersers located in the lower part of the cell body additionally saturate the cell’s contents with finely dispersed air. Due to the residual content of flotation agents in the treated water, hydroxide ion-air aggregates form at the aerator outlet, supporting the efficient precipitation of hydroxide ions of heavy non-ferrous metals, calcium and magnesium ions. This process was tested in the pilot plant KFM-180 with a raw (untreated) water capacity of up to 18 m3/h per 1 m3 of the flotation cell volume using a mixture of the tailings storage facility and mine water from JSC Safyanovo Copper. The treatment process included raw water treatment with lime, aeration in KFM cells, and filtration in a sorbent bed. The content of metal ions in the treated water is lower than in the feed water by a factor of up to 170,000 and approaches the standards: aluminum 0.016-0.02 mg/l, copper 0.0043-0.0045 mg/l, zinc 0.049-0.052 mg/l. circulating water of Soryin Tailings Storage Facility at JSC Svyatogor. The treatment process included raw water treatment with lime and alkali, aeration in KFM cells, and filtration in a sorbent bed. The content of metals in the treated water is lower than in the feed water by a factor of up to 9000: copper 0.022 mg/l, zinc 0.012 mg/l, iron 0.012 mg/l, manganese 0.015 mg/l, nickel 0.132 mg/l, arsenic 0.016 mg/l. Water hardness is significantly lower: calcium - 12.6 mg/l, magnesium - 1.1 mg/l. This process can be used in the treatment of mine, quarry, tailings storage facility, and circulating water at mining and non-ferrous metals projects."

Jan 1, 2018

By Gautam Chandra Mondal

An attempt has been made to carry out qualitative assessment of mine water discharges from the different mines of West Bokaro Coalfields of Hazaribag district of Jharkhand, India. A total of 33 mine water samples were analyzed for pH, electrical conductivity (EC), major cations (Ca, Mg, Na, K), major anions (HCO3, SO4, Cl, NO3), and heavy metals (Fe, Mn, Cu, Zn, Pb, Cr, Ni, Co, As). The hydrochemical data has been evaluated in terms of major ion chemistry, solute acquisition processes and suitability of mine water for domestic, industrial and irrigation uses. The pH of the analyzed mine waters varies from 5.27?8.43 indicating acidic to alkaline nature of the water. The electrical conductivity (EC) values varied from 276 µScm-1 to 1598 µScm-1 for measured samples and spatial differences between the EC values reflects the wide variation in lithology, surface activities and hydrological regime prevailing in the region. The anion chemistry of the analyzed water samples shows the dominance of SO4 and HCO3 with a minor contribution from Cl, NO3 and F. The observed high values of sulphate in the mine water of the area may be attributed to the oxidative weathering of pyrites. On average chloride is contributing 5% of the total anionic balance (TZ-). Fluoride and nitrate have low concentrations and on average contributing <2% the total anions. The cation chemistry indicates that 79% of the samples are Ca>Mg>Na>K, while the 6% belong to Ca>Na>Mg>K and 1% of Ca>Mg>K>Na. Weathering of rock forming minerals and cation exchange processes normally control the levels of these cations. Concentrations of some heavy metals (Fe, Mn, Ni, Cr) are found to be well above the prescribed permissible levels recommended for the drinking water. The water quality assessment for drinking purposes indicates that most of the mine water having high TDS, total hardness (TH) and sulphate concentrations. This suggests that mine water of the study area is not suitable for direct use in drinking and domestic purposes and needs a proper treatment before its utilization. The assessment of water for irrigation uses show that the water is good to permissible quality and can be used for irrigation uses. However, high values of salinity, %Na, SAR, RSC and Mg-hazard at certain sites restrict its suitability for agriculture uses. Keywords: mine water; ion chemistry; quality assessment; West Bokaro coalfields

Sep 1, 2012

By E. Barsky

The composition of multi-component materials is proved to be unambiguously determined by the composition uncertainty parameter (composition entropy). At the same time, every component, depending on its content, introduces a certain value into this parameter. Quality criterion of multi-component separation is determined by the total change of this parameter for all products obtained as a result of the separation process. This parameter can unambiguously estimate both multi-product separation and complicated schemes of modern beneficiation plants. It can be used to estimate binary mixtures separation, too. During the optimization of multi-product separation, another problem arises, which is not peculiar to binary mixtures. In this case, the total efficacy depends on the order of separation boundaries, as well. In the present paper, a specific example of initial product separation into seven products by six boundaries is investigated. It is clear that with respect to a single boundary, two products only can be obtained. In this case, the separation optimum is shown to correspond to the separation of boundary-class particles equally into both products. We have also established that from the point of view of entropy, the maximal possible separation efficacy corresponds to equiprobable composition of the initial mixture, i.e., the fine product quantity in the material to be separated is equal to that of the coarse product. Three groups of experiments were carried out. In the first group, the boundaries were consecutively specified from the finest to the coarsest one. In the second group, the boundaries were set vice-versa, i.e., consecutively from the coarsest to the finest one. In the third group, no sequence was observed. At every separation stage, a boundary was specified in such a way that the separated material composition was as close as possible to equiprobable one relative to this boundary. Total efficacy was different in all the three cases. In third group of experiments, its value is the highest, which confirms the advanced supposition. The obtained results are phenomenological, ? they can be applied to any processes of solid, liquid and gaseous materials separation.

Jan 1, 2014

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By Y. X. Yang

Bottom ash is a solid waste stream in a Waste-to-Energy (WTE) processing plant during the combustion of the municipal solid waste (MSW). In the Netherlands, bottom ash contains typically about 18% metals originated from the MSW, and current industrial practice could recover about 10% metals through magnetic and eddy current separators. The remaining 8% as the finer particles is difficult to recover through current physical separation technology. Among various alternatives, vitrification is one of the promising options to immobilize the ash and recover the remaining metals. During vitrification a homogeneous glassy slag and a Fe-Cu based alloy were obtained. In the cur-rent study, the metal alloy recovered from the bottom ash originated from a Dutch Waste-to-Energy plant contains about 82 wt% Fe, 12 wt% Cu and 6 wt% other alloying elements and impurities such as C, S, P, Ni etc. The generated alloy does not have direct commercial applications, and separation of copper from iron-based alloy is critical to obtain the market value of both copper and ferrous constituents. To find a suitable processing route of this metal alloy, various alternative approaches have been considered for an efficient removal of copper from the alloy, and the focus in the present study was on the sulphide treatment at elevated temperatures of 1400 ~ 1500oC. The tested sulphide systems include pure FeS, FeS containing sulphide mixture (such as Na2S and Al2S3), pyrite (FeS2) mineral, ZnS containing sludge as an industrial waste. It was found that the carbon saturation of the alloy is proved to be an essential condition for a proper phase separation. The results showed that FeS mixed with Na2S, ZnS containing sludge and pyrite are effective sulphide systems for copper removal with a removal efficiency of 92% by using pyrite and 95% by zinc sludge at a S/Cu ratio of around 7 times of the stoichiometry. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in a single step, and a multi-step operation is needed. The present research is expected to contribute both to the utilization of the metal recovered from bottom ash, and to the general recycling of steel scrap where copper removal from the steel scrap is a critical issue.

Jan 1, 2014

By Anuj Narang

Large-scale separation or flotation cells, used in the primary extraction in the oil sands industry, are integral parts of the overall process of bitumen extraction. Good regulation of the interface level between the bitumen froth and the middlings in these cells can result in a significant improvement in bitumen recovery and throughput, and heavily influence process economics. Automatic control of such industrial processes presents challenges such as multi-phase flow dynamics, variable process gain and time delays, poor quality of measurements and significant disturbances. This paper details a case study application of development of multiple models of the dynamics of the interface level and the design of model predictive controllers (MPC) for a separation cell process. A Model predictive controller (MPC) using linear models is designed and implemented in real time on an industrial separation cell. The industrial implementation results show that the MPC scheme provides significant benefits over the current operations which use a PID controller. The benefits include significant reduction in the variance of the interface level resulting in higher bitumen recovery and smoother downstream operation plus energy savings due to reduced underflow pump speed.

Sep 1, 2012

By V. V. Morozov, I. S. Barmin, A. V. Tugolukov, V. V. Polivanskaya

"It was presents the results of research on improving reagent regime and scheme of enrichment of slime classes of Apatite-Staffelite ores and tailings stockpile of Kovdorsky enrichment plant. It was investigated the regularities of flocculation in the processes of thickening and selective flotation apatite-bearing ores. It was established character of the influence of flotation reagents on the flocculation process. It was shown that the sodium silicate and soda ash have a stabilizing effect by thickening of sludges. Neonol and oleic acid have a coagulating or flocculating effect. It was tested the new regime flotation, involving an initial conditioning with using of reagent - dispersants before feeding the pulp into the flotation and subsequent conditioning with reagents having a coagulating effect. The flowsheet and reagent regime for enrichment of fine-grained tailings stockpiled was developed, which providing production of standard apatite concentrate and increasing the recovery of valuable components. There are presented results of the research of activities of strong organic surfactant on solubility of colloidal form fatty acid collector and aggregate stability of fine minerals in the process of thickening and flotation. Surfactants such as Neonol have been investigated for increasing the activity of the collectors. When using the process of thickening sludge fraction with flocculant Praestol 2540 and stadial conditioning of sludge were obtained concentrates containing up to 38.1% P2O5 at recovery. INTRODUCTION A feature of the Apatite-Staffelite ores of the Kovdorsky deposit is the presence of a large number of fine mineral particles and a reduced hardness of phosphate minerals (Beloborodov et al., 2010, Tugolukov et al., 2012). Formed in the ore-preparation process, sludges are lost with a discharge in the thickening operation. Sludge is characterized by an increased content of phosphorus pentoxide (P2O5). Losses of P2O5 at enrichment of the stale tailings of Kovdorsky GOK reach 14.0%. The high losses of P2O5 caused a profound study of the behavior of thin apatite classes under conditions of thickening and flotation."

Jan 1, 2018

By Massimiliano Zanin, William Skinner, Owusu Clement, Jonas Addai-Mensah, Daniel Fornasiero

This paper highlights the importance of pulp aeration in the selective separation of chalcopyrite from chalcopyrite/pyrite mixtures of varying pyrite content (20-80 wt.%). Laboratory batch flotation studies and oxygen demand tests were performed to predict the optimum amount of air required for the selective separation of chalcopyrite from pyrite. The pulp oxygen demand was shown to increase with increasing pyrite content but decrease with time as more air is introduced into the system. Complementary batch flotation tests showed significant improvement in chalcopyrite flotation under moderate pre-aeration of the pulp. However, a continuous decrease of chalcopyrite flotation was observed under highly aerated conditions. The amount of air required to achieve maximum chalcopyrite flotation recovery correlated positively with the mass fraction of pyrite in the pulps. The greater the wt.% of pyrite in the chalcopyrite/pyrite pulp, the longer the aeration time required. The optimum aeration time was established as the time before which the oxygen consumption rate constant reaches a bottom plateau. Surface analysis (XPS) indicated that the continuous decrease in pyrite recovery observed with increasing aeration time was due to the formation of more iron oxy/hydroxide on its surfaces, the same species accounting for the decrease in Cp recovery after prolonged aeration.

Jan 1, 2014

By D. Endara, E. De la Torre, S. Echeverria

"The study was conducted with the sulfide mineral from the province of Zamora Chinchipe. It was characterized physical, chemical and mineralogical, obtaining between its main results a copper concentration of head ore of 0,58 %. The mineral was homogenized and taken to direct closed circuit: rollers mill - vibratory sieve (mesh # 16). Flotation was carried out in two stages: the collective and selective where in each one were performed 6 water recirculation as suggested by the technique used to relate information of a batch flotation to a continuous circuit called cyclic flotation tests (LCT). In the collective flotation (bulk) 2 Kg of mineral were grinded with 10 Kg of balls for 30 minutes and 62.5% of solids, the pulp was taken to the flotation process with solids percentages of 33.3% and pH 7, it was conditioned with 45 g / t of KAX 1%, 50 g/t of Aerofloat 208 and 20 g /t of Pine oil. The concentrate and tailings bulk obtained were filtered separately for the recovery of water and it was recirculated to the next grinding of 2kg mineral. In the selective flotation 1Kg of bulk concentrate was carried to regrind for 40 min, 62.5% percent of solids, 10 g of lime and 5 g of tannin FLOATAN T5, the pulp was taken to the roughing-collection-refining flotation circuit controlling the pH between 10.5 and 11 where conditioning (60 g/t of Aerofloat 208 and 30 g/t of Pine oil) and adding lime to the circuit and FLOATAN according to the procedure. The four fractions obtained from the circuit were filtered; the water was recirculated to the regrind process of the bulk concentrate. In the collective flotation process tends to stability in the fourth recirculating water to obtain a copper content of 4.5% and a recovery of 87%, recirculated water represents 69.8% of all water used in the 6 recycles. In the selective flotation circuit the fifth recirculating of water is the optimal where obtaining a copper content of 13% and a recovery of 72%, recirculated water in the selective flotation circuit represents 95% of the total water used in the 6 recycles."

Jan 1, 2018

This article takes the OMRON C200HE PLC for example introducing its application in mica-paper production equipment, including style selection, address assignment of I/O point, and programming for different function. In the transformation process of simulated data and digit data, the corresponding relations between two data and so on are also discussed.

Jan 1, 2014

By C. Abbruzzese, F. Vegliò, S. Ubaldini, R. Massidda

The aim of this paper was to study the influence of different water/organic solvent mixtures (isopropyl alcohol, ethanol and ethylene glycol) on the gold desorption process. The experimental work was carried out on laboratory scale, using activated coconut carbon with different temperatures and extraction times, without adding cyanide. Best results have been obtained in this order: isopropyl alcohol > ethylene glycol > ethanol. Starting from gold concentration of about 5 g Au per kg of carbon, best kinetics resulted in 97-100% of gold extraction, after 8 hours of desorption, at a temperature of 80ºC.

Jan 1, 2003

By A. M. Amdur, A. N. Matushkina, G. I. Gazaleeva

"The article highlights results of theoretical and practical studies on the enlargement of fine gold in the process of heat treatment. The object of research is refractory gold silicate-carbonate ores of Vorontsovskoe Deposit (Northern Ural), containing fine gold. For setting up experiments and analyzing the results were used the methods of applied mathematics, mathematical statistics, mathematical and physical modeling. Modeling and calculations were performed using the software package HSC Chemistry 6.0, MatLab, setting up a full factorial experiment and other modern modeling methods. Using a scanning electron microscope, the distribution of fine-dispersed ore gold particles by size was studied. It was found that gold particles smaller than 0,4 µm smoothed the vertices and edges, i.e. they are of globules with an amorphous structure. Amorphous materials are nonequilibrium phases with high thermodynamic activity. The physicochemical properties such as melting temperature, diffusion coefficients, the content of metal impurities differ from the properties of the solid phases. In the course of the research were formulated the following scientific bases of the mechanism of enlargement of the gold particles: - the movement of dispersed droplets of gold in the process of external heat to the surface of the ore particles in the pore occurs under the action of thermocapillary pressure; - after melting of the host rock occurs flotation of molten droplets by the bubbles of gases and coagulation of fine gold; - the conditions of flotation drops of gold in oxide melts; floated drops of radius R = 1-100 µm. Analysis of the equilibrium at the perimeter of wetting a drop of gold-oxide melt-gas showed that the scheme of the tension will not significantly differ from the case of solid gold, while the radius of the gas bubbles should be at least 2 times greater than the radius of drops of gold. The proposed method of predicting the results of the enrichment of the proposed scheme, including heat treatment and gravitational centrifugal concentration of crushed ore. Experimental verification of the proposed scheme in the laboratory showed a satisfactory convergence of experiment and prediction. Gold recovery in the concentrate was 33,84 against 33,7 percent forecast. The increase in overall gold recovery to a gravity concentrate after heat treatment is more than 20 %."

Jan 1, 2018

By G. Pahomova

"It developed an alternative to traditional flotation enrichment refractory of complex lead-zinc ores to obtain conditional lead and zinc products. The scheme involves the use of the processing method of gravitational enrichment of the primary cycle and the combined gravity-flotation-hydrometallurgical in finishing. The method has a high level of comprehensive utilization of mineral raw materials in relation to the elements that are extracted in the process of enrichment in lead concentrate, and the increase in recoverable value of processed ores. INTRODUCTION The primary source of lead are complex sulphide lead-zinc ore, lead ore actually rarer. The value of lead and zinc ores (except lead and zinc) is determined by the presence in them of a wide range of associated components: silver, contained mainly in galena; gold; bismuth in the form of its own minerals, but is associated with galena; cadmium contained mainly in the sphalerite; indium, thallium and gallium contained in sphalerite and galena; selenium and tellurium are present as impurities in the sulfide, tellurium is also found in the form of its own minerals. Of note harmful impurities antimony, which is often associated with lead sulphosalts and arsenic, having a substantially own minerals. By quality (content of lead, or the total content of lead and zinc) lead-zinc ores are divided into rich, ordinary and poor; by oxidation - to sulfide (with a lead oxides content less than 15% and zinc oxide content less than 10%), mixed and oxidized (50% oxide); the latter have a subordinate importance as a source of zinc and lead. Traditionally, the most contrasting technological properties of sulfide ores of nonferrous metals considered flotation properties, which determines the priority in the selection of flotation technology of their enrichment. Other methods of enrichment - gravity (jigging and enrichment in heavy suspensions), radiometric sorting (separation) are used as preliminary operations whose main purpose is to increase the content of lead and zinc in the ore sent to flotation, as well as the removing of part of empty rock in dumping tails prior to flotation. Effective implementation of these methods is possible at large size emphasizing in the ore of lead and zinc minerals, which is typical of the rich ores and which so far mainly worked. At the same time, non-ferrous metal ores (polymetallic, lead-zinc, copper-zinc, etc.) have a sufficiently high contrast to gravitational properties since ore minerals have a higher density compared with a rock minerals. But the gravity of the practice of non-ferrous ores enrichment is not widely used, despite its high degree of environmental safety and lower cost expensive."

Jan 1, 2018

By Shibayama A.

In this research, an investigation of a process to selectively remove arsenic (As) and antimony (Sb) contained in enargite (Cu3AsS4) and tennantite/tetrahedrite ((Cu1,Fe)12(As,Sb)4S13) copper resources by leaching and precipitation were performed. First in the leaching process, the target was to selectively leach As/Sb and reduce their contents in the ores to <0.5 wt% followed by a second process to remove As/Sb dissolved in solution for environmental control. Enargite ore contained 3.65 wt% As while tennantite/tetrahedrite ore contained 5.40 wt% As and 4.85 wt% Sb. Alkaline leaching using NaHS?NaOH media at varying experimental conditions (temperature, pulp density, time, reagent concentrations) were performed to investigate the process. As/Sb precipitation studies were also performed to control high As/Sb concentrations in leach solutions by using elemental sulphur (So). Results from leaching studies showed that over 99% of As/Sb in the impure copper ores can be removed and their contents in the final solids reduced to <0.5 wt%. It was also established that such very high leaching could be achieved at 80°C within 1?6 h and pulp densities as high as 1000 g/L. The study also revealed that leach solution containing very high As/Sb concentration ranging from 5 to 20 g/L can be used as fresh solution for leaching of fresh ores until concentrations exceeding 35 g/L when it was sent to precipitation circuit for As/Sb removal. Addition of elemental sulphur at 90°C and fast cooling to 30°C allowed over 60% As/Sb precipitation and removed as Na3AsS4 and solution with reduced As/Sb concentration to leaching circuit for continuous use. Keywords: Enargite; Tennantite/Tetrahedrite; Selective Leaching; Precipitation; Sodium hydrosulfide;

Sep 1, 2012