Search Documents

By M. Lahtinen, H. Takala, B. Saxén

Oxidic zinc fume dusts are formed in electric arc furnace (EAF), Waelz furnace operations, and also in the Top Submerged Lance (TSL) furnace of Outotec Ausmelt. These dusts are normally considered as secondary raw materials for zinc metal production, as they are mainly originated from steel scrap recycling or zinc plant residue processing. The latest development in zinc fuming is direct smelting of zinc concentrates in the Ausmelt TSL furnace and hydrometallurgical treatment of produced fume dust. This technology is for primary zinc production like roasting and concentrate direct leaching, as concentrates are directly treated. The various oxidic zinc raw materials differ in composition and content of impurities. Thus, they require different hydrometallurgical processes to produce pure zinc metal. In addition to zinc these dusts typically contain also lead, silver and indium, which can be recovered and can increase recovered metal value significantly. From the impurity point of view the most relevant elements in the fume dusts are iron, arsenic, fluoride, chloride and cadmium. This paper describes hydrometallurgical processes to treat Ausmelt TSL fume dusts to extract valuable metals at high recovery and also to control and separate various impurities efficiently.

Jan 1, 2014

"Since all gold mills must sooner or later be cleaned up for permanent shutdown it was felt that a record of what was done at one mill might be of some help to those who will have to do the same job in the future,In cleaning up the mill of Delnite Mines Limited, I had an advantage that most mill superintendents will not have in that I started up the mill and was there until it was shut down, It was also known for two years approximately when the shutdown would be and for a year almost the exact time. This, of course, made careful planning possible and enabled me to get advance information that wouldn't have been available had the shutdown come unexpectedly,Early in 1964 calculation of ore reserves and the known number of working places available indicated that the mine would run out of ore sometime in August or September but not later than October, The time of course would vary with the number of competent miners that could be retained until the shutdown. Since the mining method used exclusively on the ore then remaining was cut and fill, it was known that once mining operations ceased it would require at most two days to crush and grind the last of the ore.In March 1 964 I took samples of the concrete floor under the precipitation presses, in the flux room and furnace room of the refinery and from the assays obtained proved that there would be no profit in breaking up the concrete to recover the gold from it, Samples taken from the top half inch of the concrete floors assayed less than 0, 10 oz per ton,"

Jan 1, 1966

By David J. Morrison

Scarcity of truck tyres, increasing cost and decreasing availability of labour, increases in fuel costs and project budget blowouts have changed the paradigm behind mining equipment selections. The cycle of commodity changes have occurred in parallel with the increasing maturity of continuous mining machinery, mobile in-pit crushing systems and very large scale conveyor belt systems. This paper will consider the merits of operating continuous materials handling systems, mobile in pit crushing systems, relocatable crushing systems, relocatable conveyor systems and automated waste handling systems in place of the more conventional approach of truck haulage.

May 1, 2007

By Maria Skyllas-Kazacos

The All-Vanadium Redox Flow Battery that was pioneered and has been developed at the University of New South Wales (UNSW) in Sydney since the mid-1980s is currently regarded as one of the most attractive energy storage systems for large-scale implementation in a wide range of grid-connected and offgrid applications. Several companies are now manufacturing and installing MW-scale VFBs in applications ranging from renewable energy storage, load-levelling, emergency back-up power and power arbitrage. The full-scale uptake of the VRB in commercial energy storage systems however, is heavily dependent on the availability and cost of vanadium used in the VRB electrolyte. Cost is also a function of purity requirements and although there is little scientific evidence on the effect of impurities on the VRB life and performance, VRB developers continue to demand high purity vanadium at considerable cost. This paper will provide a brief overview of the current understanding of electrolyte impurities on VRB performance together with an economic analysis of the impact of vanadium prices on overall VRB capital and levelised costs for a range of applications.

Jan 1, 2014

By Sadan Kelebek, S. O. Fekete, Gerhard W. Heinrich, Peter F. Wells

"For many years, rejection of pyrrhotite at the milling stage has been a viable method for sulphur dioxide abatement. Pyrrhotite rejection options have included the use of selective pyrrhotite depressants in flotation; a depressant which has recently come into use is diethylenetriamine (DETA). This reagent has been the subject of recent research and development efforts in the processing of nickel-copper sulphide ores.In the present study, adsorption trends for DETA have been monitored under the dynamic conditions of flotation using a spectrophotometric method which has been adopted for this purpose at Falconbridge Limited. The results indicate that the adsorption of DETA is quite fast and in the majority of cases, accounts for the disappearance of 75-95 % of this reagent from pulp's liquid phase. The adsorption decreases linearly with an increase in the DET A dosage from 100 git to 600 git. The tailings produced in flotation tests were subjected to washing with deionized water at 60 °C to examine the desorption of DET A. These results indicate that the amount desorbed increases with increasing DETA dosage used during flotation but is less than 7 per cent of that adsorbed. It was found that adsorption of DETA alone, even at relatively high levels, does not always cause depression of pyrrhotite. A new combination of reagents identified in the metallurgical laboratories of Falconbridge Limited utilizes sulphur dioxide with DETA. These reagents together are capable of efficient depression of pyrrhotite on a consistent basis."

Jan 1, 1995

By Neri Roux, Ross Gilders, Yemi Oyediran, Leo Cheung

Quest Rare Minerals Ltd. is developing their Strange Lake B Zone REE deposit located in Northern Quebec. An extensive batch bench scale testing program was launched to investigate open circuit rougher flotation performance under different conditions. The objective of the flotation study was to demonstrate the effectiveness of rejecting gangue minerals to flotation tailings while concentrating rare earth elements as well as yttrium, zirconium, and niobium into a concentrate suitable for further hydrometallurgical processing. Mineralization of interest at Strange Lake occurs within peralkaline granite-hosted pegmatites and minor aplite. The REE and high field strength element (HFSE)-bearing phases are hosted primarily in pegmatites as relatively fine-grained phases or pseudomorphs. The gangue phases comprise of quartz, feldspar, amphibole, and pyroxene. Potential ore minerals comprise predominantly of kainosite, gerenite, gadolinite, zircon, pyrochlore, and gittinsite. These complex mineralogical characteristics increase the difficulty for processing and provide a challenge for choosing the correct reagent scheme in rougher flotation. Process options including reverse flotation to reject the gangue minerals and de-sliming prior to the direct rougher flotation were investigated. Optimization trials were conducted using various reagent regimes and under different flotation conditions. Encouraging results were found using a combination of collector reagents supplied by Cytec Canada Inc.

Jan 1, 2014

By Pierre Laliberté

Introduction ??Mine ventilation is a major consumer of power in underground mining, including air heating (winter) and air conditioning (deep mines). ??Any advances, including the development of low emission vehicles, that can improve underground air quality can reduce ventilation demand, and likewise reduce costs and energy consumption, including their associated greenhouse gas emissions.

Nov 1, 2011

By Malcolm Powell

"Predicting the performance of the whole mining process is surely the holy grail of predictive simulation. This can be named ‘Integrated Process Prediction’.The objective is to be able to predict the response of the processing chain, from mining to concentration, to changes in the ore type. This can apply to greenfields design – selecting processing options to optimise the overall mine performance within the constraints and aspirations of the greater community and environment; expansion and optimisation of existing plant to deal with changes in economic drivers and ore types; and on-line control – predictive reaction to ongoing changes in ore processing types in an operation.In order to achieve this there are several broad key components that are required: ore characteristics based on in-situ rock properties; a reliable 3D map of the ore body by the key processing parameters; prediction of how the rock fragments and the energy requirement to break it; the ability to predict and track progressive mineral liberation of the rock through the reduction process; the response of rock to separation processes as a function of the rock mineralogical properties. This requires the identification of primary rock properties and associating them with the rock particles as they move along the mining process chain to a concentrate or various forms of waste.This paper looks at the value of this integrated approach; the challenges it poses; the technology and capability we require; and how as a mineral processing community we can address the challenges."

Jan 1, 2016

By C. S. Liao, S. L. Wang, C. H. Yan, F. X. Cheng

A significant development in the theory of countercurrent extraction will be presented in this article. A new term in countercurrent extraction process analysis, "Adjacent Stage Impurity Ratio" (ASIR), is proposed, and its expression is deduced. Furthermore, based on the term together with mass balance and extraction equilibrium, the conditions where a given countercurrent extraction separation operation can have minimum amounts of both extracting solvent and scrubbing agent solution can be estimated, and the equations of the two minimum amounts can be deduced. It was found that the equations for a two-component separation using a single aqueous or organic feed are exactly the same as they appeared in the theory initially established in the 1970s. Unlike its earlier version, the present derivation does not involve feed-stage-composition hypothesis, and also has the advantage of dealing with a double-feed system where both aqueous and organic feeds are simultaneously employed whereas the earlier theory can only analyze a separation using a single aqueous or organic feed.

Jan 1, 2014

By Donald Leroux, Robert Grant

"Flotation is a complex and highly multivariate process. Using the conventional OFf (one-factor-at-a-time) technique, the optimization of flotation circuits through laboratory or plant testwork is difficult, time-consuming and therefore, expensive and often results in marginal improvements. The optimal operating conditions can be more efficiently estimated when a systematic approach like SDE (Statistical Design of Experiments) is taken.The concentrator of Noranda's Brunswick Mining Division (near Bathurst, New-Brunswick) is well known for the complexity of its differential copper-lead-zinc flotation circuits. One of them, the chalcopyrite-galena separation (or CuSep) circuit, is impacted by more than 20 variables.Statistical Design of Experiments (SDE) techniques were applied at the laboratory scale to improve the performance of Brunswick's CuSep circuit. Screening tests were conducted using Fractional Factorial designs while optimization tests were carried out based on Response Surface Modelling techniques like the Central Composite design. Every series of tests, without exception, revealed new information and process insights which led to significant circuit performance improvements in the plant So far, the metallurgical gain may be as high as four percentage points of copper recovery (in the CuSep circuit). Potential cost savings of expensive consumables (steam, activated carbon) have also been identified but will require additional circuit modifications before being realized.IntroductionIn spite of its apparent simplicity, flotation is a complex three-phase (solid, liquid and gas) separation process. Fundamentally, it is a highly multivariate process. Industrial flotation circuits are commonly affected by 10 or more process variables."

Jan 1, 1997

By M. Timberlake, A. J. Jonaitis

"The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar)) filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product.Lab and Pilot testwork conducted in Australia on coal fines (55-70% -35 micron (400 mesh)) have shown that total moisture contents of less than 20% are consistently achieved in the final cake products from the Tube Press.currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50% to achieve these results.INTRODUCTIONThe DENVER Tube Press is an automatic membrane high pressure filter press, which operates at hydraulic water pressures up to 1500 PSI (100 bar). The Tube Press was developed in the late 1960's by Charlestown Engineering, st. Austell, Cornwall, England, formerly a division of English China Clays, Ltd., to address more effective methods of moisture reduction of micron-size china clays. The Tube Press reduced moisture sufficiently to produce a hard surface-dry, handleable cake and clear filtrate discharge, which was recycled into the process. This development work was conducted using a 200 Series Tube Press (200 mm diameter x 2500 mm long filter surface)."

Jan 1, 1993

By Tedd E. Lister, Andre Anderko, Peiming Wang

Mobile electronic devices such as smart phones and tablets are a significant source of valuable metals that should be recycled. Value metals in phones are gold, palladium, silver, copper, cobalt and nickel. Devices now contain increasing amounts of rare earth elements (REE). Effective recycling schemes should include the recovery of these critical materials. Targeted recycling of items containing more of the less available critical materials could address their future criticality. This presentation will describe an electro-hydrometallurgy approach to efficient recycling of metals from scrap mobile electronics. The electrorecycling (ER) process generates oxidizing agents at an anode while reducing dissolved metals at the cathode. Development of the process involved generation of E vs pH diagrams, complemented with metals dissolution experiments used to assess the effectiveness of various solution chemistries. Although several schemes were envisioned, a two stage process has been the focus of work: 1) initial dissolution of Cu, Sn, Ag and magnet materials using Fe+3 generated in acidic sulfate and 2) final dissolution of Pd and Au using Cl2 generated in an HCl solution. Results from laboratory work will be discussed.

Jan 1, 2014

By K. Sasaki

Ventilation measurements were carried out in a shallow underground-quarry space with relatively large internal volume of 14,600 m3 in order to evaluate its effective ventilation characteristics. Based on air velocity measurements with an ultrasonic anemometer in the exhaust airway connected to the space, it was found that the space was ventilated by natural ventilation airflow with intermittent changes in direction. It was difficult to measure the ventilation flow with typical methods of flow measurement provided from the intake portal and throughout the mine, because the cross-sectional area and volume of the openings were too large and the flow was variable. In the present study, a tracer gas method was applied to evaluate the effective ventilation airflow rate in the space. A photo-acoustic infra-red gas monitor, highly sensitive to SF6 gas used as a tracer gas, was set in the space to determine air exchange rates from gas concentration-time decay curves. The seasonal variations of airflow and thermal environment in the space were investigated through 13 sets of measurements taken over 15 months. Airborne rock dust concentrations were also measured at same time in the opening. The correlations between the effective ventilation airflow rate, thermal environment and dust concentrations in the opening space were analyzed and are discussed based on the presented measurements taken during year. It is concluded that seasonal variations in effective ventilation flow and the dust concentration are mainly due to differences in air temperature in the space, as affected by the rock?s surface temperature and atmospheric temperature. In summertime, the air temperature and associated air density difference generated lower natural ventilation flows resulting in higher dust concentrations.

Aug 1, 2013

By Frands Jensen, Erik Eriksson

"Haldor Topsoe’s Wet gas Sulfuric Acid (WSA) technology has been proven in a number of industries converting sulfurous gasses to concentrated sulfuric acid. In the metallurgical sector plants have been delivered handling SO2 gasses from copper, zinc, molybdenum, and lead ore. WSA has high energy efficiency and allows autothermal operation from feed gas strengths as low as 3.0% (volume). Recent variants of the WSA process have been developed that allow very high SO2 conversion efficiencies of over 99.9%. This paper describes the technology, its advantages and industrial achievements.The WSA technology is well suited for production of concentrated sulfuric acid of commercial quality from the sulfur dioxide (SO2) gas that inevitably emerges from the metallurgical processes. Some of the features that make the WSA technology attractive for this application are:- High SO2 conversion rates (up to 99.99%)- High energy efficiency leading to a low autothermal point (~ 3% SO2)- No need for gas cooling and drying to produce concentrated sulfuric acid- No production of waste- Very low cooling water consumptionThis paper describes the WSA process principles and highlights features that make this process attractive for handling SO2 gases."

Jan 1, 2014

By A. Putz, F. Vincent, A. R. Laplante

"This paper briefly reviews some of the gravity research done at McGill University and current Canadian operating practices, with emphasis on results of interest for operators. The following topics are addressed: security, economics, predicting recovery, circuit optimization, unit selection and final upgrading. Emphasis is placed on the Knelson Concentrator.The topic of security and economics are addressed jointly, in terms of the place of the gravity circuit in the mill flowsheet. Actual plant experience is drawn upon to identify potential problems and actual solutions.Predicting primary recovery is linked with a characterization of the ore, the choice of a circuit, and the fraction of the bleed used. Factors such as feed preparation, preliminary upgrading, fraction of recycle treated, ability to recover fines and location of the bleed are discussed.Final upgrading is achieved almost only by tabling and smelting. This can lead to fine gold recovery problems when more effective units are used upstream. Alternatives are discussed.IntroductionResearch on gold recovery by gravity over the past eight years has associated McGill University with a number of gold producers. This paper attempts to review the information gathered from a practical perspective. Some of the information was generated in McGill University's labs, some gathered at plant site, and some was shared by operators."

Jan 1, 1994

By J. Makgatho, P. Condori, J. Winnett, Fischerm D.

"Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit.This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration."

Jan 1, 2012

By Yi-xin Zhoa

The characteristics of coal bumps are analyzed based on the microseismic data from No.8935 workface in Xinzhouyao coal mine, Datong Mining Group. The geology of this workface is characterized by the thick sandstone roof and coal seam, both with relative higher stiffness and strength. In order to investigate the mechanism and precursors of coal bumps occurred in No.8935 workface, the locations of microseismic, the relationship of microseismic energy and frequency and the spectrum of microseismic signals are analyzed. The result shows that the coal bumps in No.8935 workface were mainly induced by the seismic caused by roof failure. The coal pillar near the goaf is more easily to bump. The statistics results indicate that the coal bumps were mainly occurred in the gate road near the pillar, less than 50m ahead of mining face and located in the hard roof adjacent with coal seam. Moreover, the frequency, energy, b-value and frequency spectrogram of microseismic events were found to decrease before coal bumps. It was found that the frequencies of the microseismic events before coal bumps mainly concentrate upon 5~60Hz. The sudden decreasing of frequency and increasing of amplitude of microseismic events can be regarded as a precursor of coal bumps.

Aug 1, 2013

By Nirmal Weerasekara, Jochen Franke, Malcolm Powell, John Favier

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By Andrew Young

A Question Murray Dodge ?Inco Stobie Maintenance ?I visually inspect my hoist ropes every day and seldom find anything. Is there a better way to do the inspection?? Based on HRIA research activities, the answer would seem to be ?yes?.

May 1, 2006

By Roger Davieds

FACT: a company?s profitability (or loss) is directly related to the efficiency and effectiveness of its maintenance operation. Fact: in order to contribute in a positive manner, maintenance must understand what its true purpose is in the organization. It is easy to say our main purpose is to increase: ?equipment uptime ?OEE ?asset life cycle We all understand this; so does management.

May 1, 2010