Search Documents

By J. Groppo, W. Zhang, R. Honaker

"The flotation of monazite is depressed when using hydroxamic acid as a collector in the presence of calcium ions which may exist due to the dissolution of minerals such as calcite. Minor dosages of sodium hexametaphosphate (SHMP) were found to effectively depress calcite, whereas the flotation of monazite was not impaired in single mineral flotation tests. However, in a mixed mineral flotation system, monazite flotation was depressed significantly. The mechanism of hydroxamate adsorption on monazite and calcite, the depression mechanism of calcite on monazite, as well as the depression mechanism of SHMP on calcite and monazite were studied using micro-flotation, electro-kinetic, and adsorption tests. Findings indicate that the adsorption of hydroxamate on monazite was due to chemisorption while adsorption on calcite was a result of physical interaction. SHMP significantly increased the negative charges of calcite surfaces which depressed the adsorption of the hydroxamate anions on the calcite surfaces due to an elevated electrostatic repulsion force. When calcium-rich minerals such as calcite are mixed with monazite, the calcium ions dissolved from the mineral surfaces specifically adsorb onto the phosphate oxygen sites on the monazite mineral surfaces thereby causing depressing effects. The addition of SHMP to suppress collector adsorption on the calcite surfaces interacts with the calcium species that were specifically adsorbed onto the monazite surface, which prevents hydroxamic acid adsorption onto the rare earth oxygen sites due steric hindrance and results in the flotation depression of monazite. INTRODUCTIONAs one of the commercial rare earth ores, monazite has been widely exploited to produce additives for catalysts, batteries, alloys, etc. Because of the complexity and the fine nature of some monazite ores, methods such as gravity, magnetic, and electrostatic separation to treat beach sand monazite fail to produce satisfactory concentrates, suggesting the use of floatation is warranted (Cheng, Holtham, & Tran, 1993). The primary associated minerals of monazite ores include ilmenite, quartz, zircon, rutile, sillimanite (Dixit & Biswas, 1969; Pavez a& Peres, 1994, 1993). Using sodium oleate as collector for monazite has been reported in many studies (Cheng et al., 1993; Dixit & Biswas, 1969; Pavez & Peres, 1994, 1993). Several investigations have reported maximum floatability of monazite occurring at pH values between 8 and 9 (Cheng et al., 1993; Dixit & Biswas, 1969). A study conducted by Pavez and Peres (1994) compared the use of hydroxamate and sodium oleate for the treatment of a monazite ore and found that hydroxamate significantly improved the grade of rougher concentrate."

Jan 1, 2016

By Baisheng Nie, Longlong Yang, Tao Yang, Wenjie Jia

"Gas adsorption in coal is an exothermic and physical process. Temperature might change during the dynamical process. In order to get the temperature variation of gas adsorption process, the experiment system which can test the temperature variation and analyze the thermal effect was established. Gas adsorption experiments under different conditions were done by using the test system. The results show that temperature increases during the adsorption process. It is an exothermic reaction process. Also, the temperature variation and the variation gradient increase with the increasing of equilibrium pressure. The temperature variation value is smaller if the experiment temperature is higher. The paper will provide basic experimental data for explaining gas adsorption mechanism better.INTRODUCTIONChina is the largest coal producer in the world while it also has the most serious coal mine disasters. According to the statistics, there are nearly a thousand coal mines in China including more than 110 the key state-owned mines risking to happen coal and gas outburst. Hundreds of coal and gas outburst occur each year which often causes serious casualties and economic losses (State Administration of Work Safety, 2007). With the continuing exploitation of the coal resources, the depth of the Chinese coal mines increases about 100 meters every year which causes the situation of gas accident becoming more and more serious (Xie et al., 2006).At present, the real mechanism of gas adsorption, desorption and the diffusion process in coal and the influence factor of it are not so clear. And because of the limit of prediction method and the technological level caused gas accident prevention theory and technology not so valid."

Jan 1, 2015

By R. Kamguem

The surface of a mechanical part plays an important role in determining performance in service. The presence of scratches left by the cutting or tearing of the material on the surface of the workpiece supports the concentration of stress and strain. This article presents the experimental study for high speed milling of the aluminum alloy 7075-T6, using cutting tools different by the nose radius and coatings (TiCN, TiAIN, TiCN + A12O3 + TiN). A multi levels factorial design of experiment (DOE) and statistical analysis was used. The roughness parameters investigated are Ra, Ra, Rv, Rc, Rsm, and Rk. The results show that the feed rate, the types of coatings and the geometry of the cutting tools have the most significant impact on the surface roughness profil. Surface finish charts according to feeds and cutting speeds were established for each tool tested.

Jan 1, 2011

By A. Dahi Taleghani, A. Shojaei

Continuum damage mechanics (CDM) of rocks is studied together with their elastic and plastic behaviors to develop simulation tools for hydraulic fracturing jobs in naturally fractured formations. The model is constituted based upon pressure sensitive inelastic deformation of porous rocks and their damage mechanisms in the cases of drained and undrained conditions. The CDM model is formulated within Fracture mechanics framework. The performance of the developed elastoplastic and CDM models are compared with the available test data of a specific shale play. The hydraulic fractures growth in the reservoir scale is then simulated; in which the effect of fluid viscosity, natural fractures characteristics and differential stresses on induced fracture network is studied. The simulation results are compared with the available solutions in the literature. The developed CDM model outperforms the traditional fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures without any essential need for remeshing.

Jan 1, 2015

By Gary M. Bone

The autonomous control of vehicles interacting forcibly with their environment, such as dozers and tractors, is an unsolved and challenging problem. Forces and motions are inherently coupled between the tool and the means of vehicle propulsion. Furthermore, they are often operated within uncertain and unstructured environments, such as those encountered in underground mining. There is a growing industrial interest in the development of robotic vehicles to improve productivity, efficiency and safety in mining and construction. This paper focuses on the modeling and control of autonomous robotic dozing for a material removal operation. A dozing process model has been developed based on observations of both a fullscale dozer and a scaled-down version. The model characterizes the dynamic interactions between the blade position, material accumulation on the blade, material distribution in the environment, and the motions of the dozer. The dozing control objective is to remove the loose material as rapidly as possible by driving forwards at full power while automatically raising/lowering the blade in response to sensor measurements. Two different controllers were developed to meet this objective. The first controller is based on a set of heuristic rules, and the second is an optimal controller based on the dynamic model. An instrumented scaled-down robotic dozer and dozing environment, designed to emulate the full-scale operation, are used to implement the controllers and compare their performances over multiple dozing passes. Experimental results are presented showing that the model-based controller increased the material removal rate by 33% compared to the rule-based controller. Lastly, technologies for full-scale implementation are discussed, followed by proposed future work and conclusions.

Aug 1, 2013

IBI Alliances ? Government ? People ? Academic ? Associations ? Media ? Customers ? Agencies ? Shareholders ? Industry consultants ? Investment Authority ? Geological Survey ? Department of Mines ? People ? Local Residents ? Mineworkers ? Academic ? University of Guelph ? Uganda Vermiculite Institute ? Associations ? TVA ? Organic Certification ? Media ? Canada ? International ? Customers ? Advocacy role ? Agencies ? Regional International

May 1, 2006

By S. Ghafarnejad Parto, Å. Rasmuson, A. Fredriksson, M. Mohammadi, K. M. Forsberg, J. Martinez De La Cruz

The present study aims at recovering rare earth elements (REE) in conjunction with the production of fertilizers from an apatite concentrate. Apatite is one of the REE rich minerals ending up in the tailings pond when Luossarvaara-Kiirunavaara AB (LKAB) in Sweden processes Malmberget’s iron ore deposit. Leaching with nitric acid, hydrochloric acid, and sulphuric acid respectively have been studied. The nitric acid route was chosen for further investigations and the optimum acid concentration for leaching of the REE were determined. The leached REE are recovered by solvent extraction using di-(2-ethylhexyl) phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid-mono-2-ethylhexyl ester (EHEHPA).

Jan 1, 2014

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from a variety of sources. This metal is known to make aqueous solutions of complex speciation as a function of vanadium concentration and pH. Considering the method of leaching, the impurities in the PLS and the planned vanadium product, different extractants and flowsheets can be applied for solution purification. In this paper, purification of vanadium leaching solution using organophosphorus, solvating and amine extractants will be reviewed. This review will be focused on vanadium separation from iron, molybdenum and uranium which are often present in vanadium resources including primary ores, fly ashes and spent catalysts.

Jan 1, 2014

By Ken Woloschuk

??Owners?Perspective ??Owners?Challenges ??EcoNomics?Delivery Model ??Projects ??Project Outcomes ??Questions ??Balancing the triple bottom line initiative: ?shareholders expectations of economic costs and benefit; ?stakeholders expectations of social and environmental costs and benefits; ?deciding what is sustainable and which design alternatives are the most sustainable. ?? Delivering required project outcomes

May 1, 2008

By J. Smit, F. Parada, R. Parra, E. Balladares, M. P. Merino

"In this study, a two-step process was developed for recovering copper, molybdenum, zinc and iron (hematite). In the first step, grinded slags (-65 mesh) were sulphated with SO3 at 350-500ºC to form iron, copper and zinc sulphates. In the next step, the formed sulphates were decomposed to hematite, copper and zinc sulphates and oxysulphates at 700-750ºC. The generated SO3 was recirculated back to the sulphation step. The generated calcine in the decomposition step is leached with 25 gpl acid at 50ºC to dissolve the copper, zinc and molybdenum for further conventional separation and recovery. The hematite residue, of intense red color, can be used as pigment, in the ceramic industry or as pellet feed. The fine crystalline silica remains in the hematite residue."

Jan 1, 2014

By J. E. Lee

"This paper describes the current practices and experiences, and discusses design parameters concerning slurry pumping at Inco Metals Company in the Sudbury District. It deals mainly with the long tailing and concentrate lines. Subject matter is arranged under the following headings: pumps, lines, instrumentation, system design, operation.IntroductionThe Inco Metals Company is the mining and processing section of INCO LIMITED. In the Ontario Division, it operates 13 mines, 5 mills, a smelter, an iron ore plant and 3 refineries, all engaged in the mining and recovery of nickel and copper. This paper describes the slurry pumping practices in the mills of the Ontario Division.The PumpsWe have in our Sudbury area mills most of the available types of slurry pumps, in sizes from one inch up to twelve inches, a total of about 400 pumps. The rubber-lined, horizontal shaft pump is; most numerous. However, for certain applications, the hard-metal pump is essential, and is becoming more popular for general mill service. Two types of vertical shaft pumps are used. There are a few diaphragm pumps on small thickeners, but the larger thickeners have centrifugal pumps either directly connected to the under-flow or with one pump handling several gravity underflows. We have not used piston or plunger pumps in our mills."

Jan 1, 1978

By Jessica Hurst, Mark Holdsworth, Jeff McKay

"In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart. INTRODUCTIONRio Tinto’s Kennecott Copperton Concentrator produces copper, molybdenum, gold and silver. The mill has 4 SAG mills (SAG 1-3, 34 foot diameter and SAG 4 36 foot diameter), 8 ball mills and copper and molybdenum flotation plants, as seen in Figure 1. The 2010 average data is shown in Table 1.In 2002, a Metso Cisa OCS Expert Control system was installed at Copperton for SAG and Ball mill advanced control. The expert control was first placed on SAG 2; data from the first few weeks compared with operator performance indicated approximately an 11 percent increase in throughput. After full commissioning, the system was gradually refined further by plant personnel to develop key performance indices based on SAG feed size, refinement of the sound setpoint for control of mill speed and throughput, specific rules to help the adjustment of speed based on loss of a feeder, etc. With the addition of the pebble crushing circuit, the expert control began utilizing a model estimation of crushed pebble bin level to help stabilize the impact of returned crushed and uncrushed pebbles on the SAG mills. As the ore and limitations change, it is necessary to evolve the SAG logic to better handle any constraints."

Jan 1, 2012

By Y. Miyabayashi, K. Nishikawa, H. Nagai

JX Nippon Mining & Metals Group recovers valuable metals from end-of-life electronic products in an economical and environmentally-benign way, based on technologies that have been acquired in mining, smelting, and refining operations over time. End-of-life electronic products contain halogens and hydrocarbons. When such materials are treated in the copper smelting process, corrosion of equipment and discoloration of sulfuric acid occur. As a countermeasure to these problems, we have developed pretreatment processes that include an incinerator, exhaust gas washing towers, and a defluorination facility. By implementing these improvements, we have been able to treat a large volume of end-of-life electronic products efficiently in the copper smelting process.

Jan 1, 2014

By G. J. Desroches, E. Ozberk, M. J. Collins, B. D. Krysa, I. M. Masters

The zinc refinery of Hudson Bay Mining and Smelting Co., Ltd. went through a major modernization in 1993, when the roaster and the calcine and fume leach circuits were replaced by a new Sherritt zinc pressure leach plant. The HBMS plant, in Flin Ron, Manitoba, represents the first commercial application of the Sherritt two-stage zinc pressure leach process, with /00% of the zinc concentrate feed processed in autoclaves. The process design of the new plant required definition of the deportments of elements such as antimony, arsenic, chlorine, cobalt, fluorine, germanium, magnesium, manganese, selenium, tellurium and thallium. This paper describes the deportment of these elements in the commercial zinc plant during the first nine months of pressure leach operation, and compares these results with operations prior to the introduction of pressure leaching, and with the results of tests carried out in the She"itt laboratory during the process development phase.

Jan 1, 1995

By François Charette

High stress conditions in underground mines push the performance envelope of support systems to their limit. In weak rock masses these conditions lead to large deformation and breakdown of the rock material, while stress release events in hard rock mines can lead to sudden and usually violent rock and support failure. In typical support systems, a combination of different reinforcement and support mechanisms provide the required convergence control and retainment. These systems usually involve a multi-pass support installation. The advantages of a single pass support system are investigated and several bolting combinations are compared. Criteria for design are reviewed and new criteria are proposed to include cost and effectiveness in commonly used engineering approaches. Field observation and testing is used to illustrate the difference between the proposed approach and more conventional systems.

Nov 1, 2011

By K. Becerra, D. G. Almond, T. D. Maru

"Nkomati Nickel Mine in South Africa processes one of the world’s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster.Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program.The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control."

Jan 1, 2012

By A. J. Hyett, N. Hedrick, J. Blackall

The Garford bulb anchor is a modified cable geometry developed and patented by Garford Ply Ltd. of Australia, and which has recently become widely available in Canada. It is produced by deforming the seven wires (including the central kingwire) of a standard cable into a bulb" (Fig. 1). Laboratory cable pull tests indicate that the bond capacity of the 25 mm Garford bulb anchor is comparable to the nutcase cable, in excess of the birdcage cable, and significantly higher than standard 7-wire strand. Its comparative advantage over the latter is most significant for tests at low radial confinement and high water:cement ratio grout, which corresponds to operational conditions of low quality rock (i.e. weak, highly fractured rock masses, foliated hanging walls, failed ground, etc.) and poor installation quality control (perhaps the most common explanation for cable bolt failures). It is under such conditions that cable bolting is often ineffective. The most impressive result is that for a reduction of the effective rock mass modulus by a factor of five, the Garford bulb cable capacity remains virtually unchanged.

Jan 1, 1995

By Hong Zhong, Shuai Wang, Gang Zhao, Lanqing Deng, Guangyi Liu

In this paper, three novel surfactants containing double reactive centers(-CONHOH and –CONH-), double hydrophobic groups were designed and synthesized as collector for separation of diaspore and aluminosilicate minerals, such as N-(4-(hydroxyamino)-4-oxobutyl)octanamide (HA-8), N-(4-(hydroxyamino)-4-oxobutyl)decanamide (HA-10) and N-(4-(hydroxyamino)- 4-oxobutyl) -dodecanamide (HA-12). The adsorption mechanism of N-(4-(hydroxyamino) -4-oxobutyl)alkylamides (HA) onto diaspore was also investigated by FTIR spectra, zeta potential measurement and DFT. The flotation results demonstrated that three collectors all exhibited superior collecting power to diaspore and selectivity against kaolinite and illite, and could effectively realize flotation recovery of diaspore from bauxite ores contained aluminosilicate minerals under neutral conditions. Moreover, HA-12 was a superior collector than other two collectors for bauxite separation. The results of XPS, FTIR spectra and zeta potential illustrated that at around pH 6.0, HA might chemisorb on diaspore surfaces through Al-O coordination bonds formed by binding its –C(=O)NHOH or –C(=O)NH– chelate groups with aluminum atoms on diaspore surfaces. HA’s unique properties, such as characteristic bond patterns onto diaspore surfaces, double hydrophobic groups, and intermolecular hydrogen bonds between neighboring HA molecules coated on diaspore surfaces, rendered it to be a superior flotation collector for diaspore.

Jan 1, 2016

By J .. R. Dalton

"Blasting in high sulphide content ores presents at least two major safety considerations: (1) compatibility of the explosives with the ore while resident in the borehole; and (2) introduction of a flame and shock producing explosive into this environment, while minimizing the risk of reactive ignition in the chemical reaction products/sulphide dust cloud resulting from the detonation. This paper will discuss only the second consideration, i.e. post detonation reactivity.The ETI (Explosives Technologies International) Technical organization, in consultation with the U.S. Bureau of Mines, reasoned that the most relevant considerations in the development of an explosive for this application are:• minimization of reactive gaseous detonation reaction products;• flame duration reduction;• flame temperature reduction;• increased explosive sensitivity;• reduced probability of ""low order"" detonation; and• maintenance of energy level as high as possible.Obviously, not all of these are totally independent properties, i.e. increased sensitivity will reduce the probability oj low order detonation as will higher energy levels. However, these considerations were examined separately as if they were independent."

Jan 1, 1994

By T. Nomura, N. Saitoh, K. Tamaoki, Y. Konishi

We have developed new recycling technologies, based upon an eco-friendly biotechnology, in order to extract precious and rare metals sourced from end-of-life products and electronics. We have been focusing on the metal ion-reducing bacteria, Shewanella algae and Shewanella oneidensis, that are able to reduce and deposit gold ions (Au(III)) or PGMs ions (Pd(II), Pt(IV) and Rh(III)) into metal nanoparticles at room temperature within 120 min. When processing the aqua regia leachate of printed circuit boards, Shewanella bacteria were able to rapidly and selectively collect gold ions under acidic conditions in the presence of heavy metal ions, proposing a new bio-recovery system for gold. This biotechnological procedure also has the potential to allow the recovery of PGMs from the leachate of automotive catalysts. Shewanella bacteria were also able to successfully perform the complete reduction and deposition of the PGM ions. The ability to collect the PGM ions suggests that this represents a new process for the biorecovery of PGMs from used automotive catalysts. Our proposed biological method enables the rapid and highly efficient recovery of precious and rare metals via separation and concentration utilizing microbial reactions at room temperature.

Jan 1, 2014