Search Documents

By J. J. O?Neill

Introduction The Beattie mine is the first of its character to be exploited in Quebec. It is primarily a large low-grade gold deposit containing values which a few years ago would not have been considered as ore. Much interest is attached to this development as its success may mean a greatly enlarged scope to gold mining in Canada on deposits which have formerly been considered worthless. Because of its potential importance as a pioneer in low-grade gold mining, the Quebec Bureau of Mines decided to make a careful detailed study of the Beattie in the hope not only of assisting in its development, but of stimulating the search for similar essential geological conditions in other parts of the Province. This paper is a summary of the results obtained during two months on the property in 1932, supplemented by a few trips underground in 1933. The full report will appear in the Annual Report of the Quebec Bureau of Mines for 1932, Part C. Location and Means of Access: The Beattie ore-body is situated two miles west and one half mile north of the centre of Duparquet township, and approximately 22 miles north 28° west of the town of Noranda. Until the fall of 1932, access to the property was from LaSarre, on the Canadian National railway, over a thirty-mile water route with one portage 600 feet long; about 2,000 tons of machinery and supplies were taken in by that route. An automobile road, nine miles long, now connects the property with the Makamik highway, and a narrow-gauge railway, without ballast, gives outlet for concentrates from the mill to the C.N.R. tracks of the Rouyn-Taschereau line, nineteen miles distant.

Jan 1, 1934

Building block cave operations involves significant commitments to capital and time before arriving at completion or full scale production. The focus of the mine planners is habitually to minimize the upfront capital and achieve target development rates and construction dates. However, management of the construction of block cave projects requires understanding of the strategic/tactical decisions that the project planners can take to increase the value of the project and cope with schedule risks. As block cave projects involve development of vertical and lateral access to the underground footprint and ore body, more attention to uncertainties is required as most of those projects need to confront delays leading to a decrease in value. The standard process of development and construction scheduling is often not planned with provisions to realise uncertainties in the construction phase. Uncertainties and risks such as poor ground conditions and equipment breakdowns are the primary reasons for schedule slippage. As a result most of these projects experience delays. In order to mitigate risk to the project schedule, we centre our attention on increasing the value of the project by spending more money upfront and improving the schedule rather than focus on minimizing the upfront capital. Scenario-based simulations along with project appraisal methods hold great promise to address those challenges and enable mine planners to make better decision and enhancing project value. This paper will present a hybrid simulation based approach to model the process of development and construction based on discrete event (DES) and continuous based simulations (CBS). Such simulations will be conducted for scheduling multiple development headings (Apex, undercut, extraction, and haulage levels). Two scenarios are utilized to investigate the impact of risks on schedule and how flexibility in construction can be incorporated to minimize delays: (1) The bench mark scenario is created based on actual data from an existing case study. (2) The flexible scenario is an alternative way to use primary production infrastructure (Ore Handling System) including conveyer drifts, conveyer belt, and a gyratory crusher in the construction process and that requires the system to be in place before starting lateral development in the footprint. As a result, a truck-load system versus a conveying system will be studied to observe the gain in construction speed and to estimate the premium cost for mucking rock from headings and drawbells and transporting it to surface. Such strategic flexibility would be part of the original budget to make the tactical flexibility available during construction. Continuous cash flow models are used to evaluate and compare the scenarios. This study is an example of how new techniques in planning can be used to support decision-making processes in block cave design.

Aug 1, 2013

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By B. R. Maas

Processing material at a consistent rate through the continuous countercurrent decantation (CCD) thickeners presented a major bottle neck to unlocking additional value from one of the post-flotation streams at the Kansanshi processing plant. The manual operation of the thickeners making up the CCD train resulted in frequent imbalances and process upsets across units. The automation of CCD trains is notoriously tricky as the available manipulated variables are outnumbered by the parameters requiring regulation. The implementation of an advanced, auction-based, control philosophy to manage the movement of both slurry and solution inventory through the train addressed this parameter imbalance and lead to the stabilisation of the circuit. Since the commissioning of this control strategy: an additional 7 200 dmt/day (+36% throughput) of material can reliably be processed through the train, the number of monthly downtime events has reduced, and a saving of $354 000/month in reagent cost has been achieved. INTRODUCTION CCD operation Agitated leaching is a common method used in hydrometallurgy to extract a metal from its host ore. The host ore is initially finely ground to liberate the surfaces of the valued minerals and improve the kinetics of the leaching process. The ore is then contacted in an agitated tank with a lixiviant to dissolve the desired metal into the aqueous phase. The resultant slurry from the leaching process comprises of a solution pregnant in the metal salt and a barren ore. The first purification step taken after leaching is to wash the pregnant liquor solution (PLS) from the depleted ore. On the industrial scale, a set of between two to ten thickeners arranged in a countercurrent configuration is often used to carry out this separation (Perry & Chilton, 1973). The slurry is introduced at the head of the train and a wash solution at the tail. The two streams are pumped through each thickener countercurrent to one other. At each stage the residual PLS in the slurry is mixed and diluted down with the countercurrent overflow solution from the downstream thickener. The diluted slurry is fed into the thickener where the solids separate out through gravity sedimentation. The settled solids are channelled towards the underflow of the thickener by a rake mechanism and pumped downstream to the next thickener in the train. The outcome is the recovery of a PLS from the overflow of the lead thickener and a slurry of washed solids from the underflow of the tails thickener.

Jan 1, 2019

By M. V. Rowley, D. D. Warkentin

With high commodity prices, tightening operating budgets and increasing disposal costs, there is an increasing interest in processing municipal waste streams, such as the ash derived from combustion processes. This paper describes laboratory development work for a process to recover metal values from the finer fractions of these wastes. The work was initially aimed at recovery of copper and the removal of lead and other heavy metals from the ash residue, but results showed gold and silver recovery to be an important objective as well. The process uses gravity and flotation as the principal separation steps, with gold recovery occurring mainly in the flotation stage. The particle size range and chemistry of the ash presented numerous challenges to developing a suitable flotation method, but an effective flowsheet was developed by separating the ash into a fine fraction and a separate slime fraction, each with a unique flotation strategy. Specialized conditioning stages and careful reagent selection have resulted in effective gold and silver recovery from a range of ash types and sources. The work has resulted in a patent being issued for a process based on this novel approach to the treatment of combustion wastes.

Jan 1, 2017

By Pura Alfonso, Teresa Escobet, Hernan Anticoi, Eduard Guasch, Josep Oliva, Sarbast A. Hamid

"The liberation modelling of mineral particles using mineral liberation analysis have been used in the past to model comminution and concentration processes. In this work this concept has been taken a little further, using comminution and concentration for applying the mineralogical characteristics of particles. This approach is shown using the image analysis, mineral liberation analysis and the distribution density functions for liberation modelling. The work focused on the effect of comminution on mineral liberation for liberation modelling. To model this, effect the mineral liberation of the particles using distribution density and the cumulative distribution was linked to the image analysis of the ore particles. These properties have been estimated by statistical measures such as the distribution density and liberation grade, which were extracted from MLA data and images analysis, using proper image analysis and techniques based on MATLAB software. A comparison of different tungsten ores of liberated particles, has been introduced and evaluated by estimated results and image analysis.INTRODUCTION The chief economic minerals of tungsten are wolframite [(Fe,Mn) WO4] and scheelite(CaWO4), and approximately two-thirds of the world tungsten reserves consist of scheelite deposits (Lassner and Schubert, 1999). Tungsten has unique properties and is widely used in various industrial high strength and high temperature applications. It occurs coarsely aggregated in low grade ores. Most of tungsten ores, particularly scheelite, wolframite and ferberite, occur in deposits with very low content of WO3 (0.1–2.5%) that is not economically viable to apply directly metallurgical methods to extract tungsten (Martins, 2014). Tungsten is considered as a critical metal by the European Union by the economic importance and also the high supply risk (European Commission, 2014; Chakhmouradian et al., 2015).Currently, scheelite is playing an increasingly important role in tungsten industry because the mineral reserve of wolframite is getting depleted after gradual exploitation and utilization (Min et al., 2016). In mineral processing, the liberation of valuable mineral from the gangue determines the efficiency of subsequent separation processes. The liberation characteristics of an ore are primarily dependent on its texture, the association of mineral in the host matrix of gangue minerals, and to some extent on the grinding process (Zhang and Subasinghe; 2013)."

Jan 1, 2017

By Patrick S. Hudd

Traditionally in hard rock mining, large diameter raise boring was thought of as 3.04 metre or 3.66 metre diameter holes 300 metres deep. Mine and ventilation engineers were challenged to design systems either incorporating such holes, or slashing and modifying to suit. Now, 5.49 metre diameter holes up to 1,000 metres deep are being excavated. The ability to pilot and ream such holes not only creates new options for mine engineers in mine ventilation system design, but also creates new opportunities in mine access. By combining holes of this diameter with the ability to accurately drill long pilot holes within the diameter of the pilot hole through the entire length of the hole, borehole hoisting systems are now fully capable of being main production or service accesses for mines. This paper will review the present day capabilities of large diameter raise boring, potential applications for such excavations and some considerations for companies contemplating using large diameter raise boring in their operations

Oct 1, 2010

By Ian Ewart, Trevor Bergfeldt, Gourab Satapathy, Ajay Patel

"Conventional electrowinning (EW) of nickel from sulfate electrolytes is complicated by several factors including the requirement for a diaphragm cell to separate the anolyte and catholyte and the need to minimize nickel mist emissions. Developed and commercialized by emewCorporation, this novel process electrowins high purity nickel cathode (99.5%) from copper refinery bleed streams using the proprietary emew vortex EW technology. The emew nickel process incorporates high flow rate in an enclosed cylindrical EW cell operating at high current densities that overcomes the challenges of conventional nickel EW and completely eliminates the risk of nickel mist emissions. The tubular cathodes are easily harvested and mitigate the effect of plating stresses inherent in nickel EW. The present paper describes the emew nickel process and its most recent application to copper refinery bleed streams at full-scale.INTRODUCTION To meet the stringent demand of customers, nickel producers are giving prime importance to production of high purity nickel cathodes. The major challenge for refineries is to improve cathode quality and appearance despite fluctuating electrolyte impurity levels. The basis of achieving good quality cathode includes the control of electrolyte impurities and consistency of specific process conditions. The commercial operation of emew nickel technology has been successfully implemented and has demonstrated the ability to produce high quality nickel cathode from refinery bleeds. This paper emphasizes the importance of upstream impurity removal to achieve the required nickel emew feed composition by evaluating the benefits of using selective precipitation as a purification scheme with the aim of improving the overall nickel recovery while ensuring suitable nickel concentration in the advanced electrolyte is achieved. Nickel electrowinning is similar to other electrowinning processes that employ insoluble metal anodes & cathodes. It requires the passage of direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. For the recovery of nickel from solution, the most common methods are electrowinning and hydrogen reduction. Electrowinning usually occurs from sulfate, chloride or mixed sulfate/chloride electrolytes. In sulfate electrolytes, nickel electrowinning cells are normally designed to achieve specific criteria as outlined below (Robinson & Tuppa, 2002):"

Jan 1, 2017

By C. Chongo, L. Little, Q. Mclennan

Since commissioning in 2005, First Quantum Minerals’ Kansanshi Mine in Zambia has produced over three million tons of copper and 1.8 million ounces of gold from a deposit with highly varied copper mineralization. The processing plant is complex with three independent flotation circuits, gold gravity concentration, atmospheric and high pressure leaching, solvent extraction, and electro-winning. For the first ten years of operating the plant, copper mineralogy was inferred from total copper and acid soluble copper assays, and various misconceptions developed about the mineralogy which impacted operational strategy and project decisions. In 2015, an on-site mineralogy section was set up with an Automated Scanning Electron Microscope, the Zeiss MinScan. This instrument has provided detailed mineralogical data that have debunked some of the mineralogy myths that had developed, highlighting the key underlying issues affecting processing performance. This has enabled the development of projects targeting losses of specific copper minerals in defined size classes, unlocking significant value. This paper describes some of the early misconceptions around mineralogy at Kansanshi processing plant, outlining projects that have benefitted from understanding copper mineral distribution. Learnings from Kansanshi are to be applied at other FQM sites, with a similar mineralogy program being set up at the Cobre Panama project. INTRODUCTION The deposit Kansanshi Mine is located in the North Western Province of Zambia, and it has been the largest copper producer in Africa for over a decade. The deposit occurs within a broad northwest trending antiform that can be traced for 12 km, hosted in a zone of complicated faulting, abundant vein injection, breccia development and down-dropped rock units that lies within Kansanshi’s mining license. The copper mineralization within the deposit is predominantly vein-hosted, although some is strata-bound, occurring in thin bands and veinlets parallel to foliation, and some is disseminated associated with albite-carbonate alteration (Gray, 2015). Supergene enrichment has led to significant variety in the copper mineral speciation. This alteration is complex, and has not followed the text-book principles with a neat layer of supergene mineralization overlying fresh hypogene ore. Rather, the occurrence and extent of oxidation and supergene enrichment is highly irregular throughout the deposit, sometimes occurring at significant depth in localized pockets and along fault lines. Gold mineralization tends to follow the copper within the deposit, but it is dominated by coarse-grained, free-milling native gold. The extent of copper oxidation – measured as the fraction of total copper that assays as acid soluble – is used to classify ore into three main ore types, named Sulphide, Mixed, and Oxide, which are then fed to three different primary crushers for processing in independent circuits.

Jan 1, 2019

By M. Kim, M. Ha

"The effect of red mud on the melting behavior of ferronickel slag was investigated by a laboratory-scale horizontal tube furnace. Melting and softening of slag samples fluxed with different amount of red mud was examined by in-situ visualization technique at temperature range from 1400 to 1550°C. FactSageTM 7.0 was used for the thermodynamic calculation of multi component system of ferronickel slag and red mud. Liquid phase area was extended to lower temperature by adding red mud indicating its suitability as a flux material. X-ray diffraction analysis confirmed the dependency of the phase changes on the red mud content. Microscopic observation by scanning electron microscope (SEM / EDX) clarified the phase transformations from olivine to spinel along with red mud additions.INTRODUCTION Ferronickel smelting by submerged arc furnace (SAF) is an energy intensive process performed at high temperature range 1500–1600°C. During the smelting process of saprolitic nickel laterite ore with a nickel content of 2.2–2.3 pct, a large quantity of ferronickel slag is being produced that account for 97 pct of ore charged. To achieve ferronickel grade of 15–20 pct Ni, electrical energy of 80 to 85 MW is used for the melting and reduction of nickel oxide (NiO) and iron oxide (FeO) in the ore (Rodd et al., 2010). Unreduced components, mostly MgO, SiO2 and partly FeO are removed from the furnace in a liquid slag form by a tapping operation. Due to the high melting temperature, forsterite (Mg2SiO4) based slag containing approximately 10 pct FeO requires typical process temperature of 1600°C. Flux in metallurgical process is a medium that decreases melting and operating temperatures while it increases fluidity of the liquid slags. Calcite and fluorite are examples of flux materials used for the ironmaking, steel refining and continuous casting process. Oxide systems based on CaO - CaF2 - SiO2 - Al2O3 - MgO cover most of the slag composition in ferrous metallurgy accordingly. Crucial operating factors for ironmaking and steelmaking slags are basicity (typically CaO/SiO2 ratio), viscosity and impurity levels. These are extensively controlled by the fluxes. General metallurgical fluxes such as limestone, dolomite and calcium fluoride are abundant in nature and supplied to steel mills at low prices. Meanwhile, in copper flash smelting process, silica is supplied with copper concentrate to remove iron oxide (FeO) generated from sulfide oxidation. FeO - SiO2 binary system formulates eutectic area at 25–38 pct of silica that has low melting temperature below 1205°C. Fayalitic system (Fe2SiO4) that has low viscosity (0.1 Pa·s) (Park et al., 2011) facilitates easy separation of slags from molten sulfide mattes. Recently, copper plants actively utilize recycled raw materials as a flux. Various recycled glasses are ground and fed to copper smelting process as a partial replacement of silica ore. Applying industrial wastes to smelting processes is advantageous since the operators can reduce the production cost remarkably. Not to mention the consumption of recycled materials can ultimately minimize the environmental risks and the waste management costs. The authors, therefore, investigated the reasonable waste materials that can be effectively used for ferronickel smelting process. Prerequisites for potential fluxing materials are non-recyclable property, low transportation cost and excellent performance as a flux."

Jan 1, 2017

By D. F. Zhang, X. Q. Jiang, N. Tahreen, D. L. Chen, F. S. Pan, D. Y. Li

Alloying with rare-earth elements has been proven to be an important tool for magnesium to achieve superior properties via texture randomization. The role of yttrium in texture weakening and the link between texture and formability are fairly well known. Since annealing is a vital part of metal processing which could significantly contribute to ductility, it is important to ascertain the impact of annealing in terms of texture change. Also, an understanding about texture development during pre- and post-deformation annealing is essential to improve the industrial deformation processing as texture is closely related to formability. While there is independent information in the literature regarding the effect of rare-earth addition and heat treatment on the texture formation, no systematic studies have been reported on the collective impact of yttrium addition, annealing and deformation on texture evolution. The present study was, therefore, aimed to identify the inter-relationship among texture evolution, yttrium content, heat treatment and deformation behavior in an extruded Mg-Zn-Mn-Y alloy. Annealing at 450°C for 1 hour and uniaxial compression tests at a certain amount of deformation were performed. The deformed and annealed samples were then subjected to annealing and compression test, respectively, followed by texture measurements. It was observed that yttrium addition effectively weakened the crystallographic texture in all conditions, which was evident from the changes in the microstructures and textures.

Jan 1, 2015

By S. Litke

Elemental sulfur was stockpiled at the Mount Polley Mine for use as a source of sulfuric acid as part of research into leaching copper from oxide ores, but the project did not proceed beyond an initial pilot- scale evaluation. Since placement, the sulfur has oxidized and some sulfuric acid leached into the underlying rock. The reaction of the acid with these underlying materials has been studied as part of an evaluation of the effects of leachate from the pile. The rock underneath the sulfur pile is composed dominantly of primary and secondary alumino-silicates with less than 1% carbonate (calcite) and iron sulfide (pyrite). In its unaltered condition, the rock is classified as non-acid generating. Conceptually, it was expected the sulfuric acid would be neutralized by the rock to varying degrees resulting in a series of pH-controlled weathering fronts progressing from leached near the contact with the sulfur pile (pH <3), to active neutralization by silicates (pH 4–5), to active neutralization by carbonates (pH >7). The rocks underneath the pile were sampled to determine the extent to which the rocks had reacted and their long-term stability after removal of the acid source. INTRODUCTION When rock is blasted and excavated to facilitate mining ore, it is typically placed and stored on the surface in piles. The resulting drainage may have a neutral to basic pH (i.e., non-acidic drainage) or a low pH (i.e., acid rock drainage, ARD) depending on the mineralogy of the rock being stored in the piles. Acid- base accounting (ABA) can be used to characterise the two types of rock: potentially acidic drainage generating (PAG) and not potentially acidic drainage generating (NAG) (Price, 2009). According to Price (2009), NAG is defined as having an excess of neutralization potential (NP) in the rock in the form of calcium carbonate-like minerals when compared to acid potential (AP), i.e., a Neutralization Potential Ratio (NP/AP = NPR) greater than 2.0, whereas PAG is classified as having an excess of AP (i.e., an NPR less than 1.0). This is a conservative estimate and may be slightly modified depending on the mineralogy at specific mine sites. Rock with an NPR of 1–2 is also capable of generating acid (Price, 2009) and, depending on the mineralogy, may also be classified as PAG. Drainage from PAG material can generate acid immediately, or many years after it has been exposed to surface conditions. Disposal techniques depend on the category (i.e., NAG or PAG) and reactivity of the rock stored in the piles.

Jan 1, 2019

By Stephen Esposito

Outline ? Brief Overview of Solid Energy New Zealand ? Need for Integrated Risk Management at Solid Energy New Zealand ? Overview of Solid Energy?s IRM program ? What are the results and key learnings? Overview Of Solid Energy New Zealand ? 100% NZ Government Owned ? Produces 95% of New Zealand?s Coal ? Sales turnover USD150 million per year ? Sold 4 million tonnes of high quality coal in 2003 ? Coking and Thermal coals ? Exported 2 million tonnes of coal ? Significant international and domestic growth expected going forward

May 1, 2004

"The successful commissioning and ramp up of the Albion Process™ at the GPM Gold Project relied on the successful scaling up of the process from batch and continuous pilot plant campaigns (Voigt et al., 2015). Critical information about reaction kinetics and residence time, grind size and pulp density were determined at the laboratory scale and successfully applied to the commercial scale. A limitation of small scale testwork, is that some parameters cannot be measured reliably and scaling up is a function of the physical size of the equipment which isn’t possible to test with laboratory scale equipment. Oxygen mass transfer rate is one such parameter since this is a complex interaction of many factors including slurry temperature, solution and slurry chemistry, slurry viscosity, agitator type, dimensions and power, oxygen bubble residence time, oxygen purity, tank geometry and oxygen injection technique. Oxygen generation represents an important operating cost for the Albion Process™. Pivotal to the Albion Process™ operating economically at atmospheric pressure is the capability to efficiently transfer oxygen while utilising as much oxygen injected to the process as possible. To respond to this Glencore Technology developed the HyperSpargeTM supersonic gas injector. This paper compares the HyperSparge™ against other sparging techniques to quantify the benefits of oxygen injection via a supersonic gas jet on scale up of the oxygen mass transfer system. The paper then examines plant survey data from the GPM Gold Project to demonstrate the very high oxygen utilisation that can be achieved with a correctly designed oxygen mass transfer system.INTRODUCTION One of the main challenges in chemical reactor design is the scale-up of processes from the laboratory to industrial scale. Processes which cannot be faithfully simulated with an experiment at the laboratory scale face challenges due to the physical dimensions and complexity of full scale operation. One example of this is the design of oxygen mass transfer systems in atmospheric oxidative leaching circuits such as the Albion Process™. A number of constraints associated with the use of laboratory scale equipment to design full scale circuits are involved in gas mass transfer processes in agitated slurries such as the Albion Process. Chiefly, typical laboratory and pilot size equipment lacks the required volume to provide useful design data without relying on empirical correlations: the specific agitator power input is artificially high, the bubble residence time in the vessel is artificially low, the oxygen partial pressure at the base of the vessel is artificially low and the oxygen delivery method may differ significantly to the industrial process. Further, the dynamic nature of the process introduces additional impacts on gas mass transfer, including the presence of solids, recycle streams and minor elements, plus the variances within the reality of a process plant such as disruptions or variance of feed quality."

Jan 1, 2017

By L. Callele, C. DiGiovanni, L. Li, R. Driver

"Hot-dip galvanizing is a common procedure used to protect structural steels from corrosive environments. However, in a construction project involving welded structural steel platforms by a Canadian steel structures company, numerous connections were found with large cracks in the welded corner joints and T-joints after galvanizing. Historically, in other similar projects by the same industry partner, cracking did not occur making this an unforeseen and new phenomenon. The project explored the mechanical properties of the base material, the thermal stresses induced by the hot-dip galvanizing, and the fracture surface of the cracks. A key feature to note, the fracture surface showed intergranular cracking with no plastic deformation. Lab testing showed the base material exhibited intergranular brittle behavior when heated and fractured at the galvanizing temperature. The transition to a brittle fracture mode is due to temper embrittlement and the segregation of elements in the grain boundaries.INTRODUCTION Galvanization is a common practice for protecting steel structures from the corrosive environment. Hot-dip galvanizing is the most common approach to bonding the zinc layer to the steel, and it is highly cost effective. In the case of welded structures, it is common to do the hot-dip galvanizing process after welding. This is so the protective layer can be applied to the structure as a whole and over the welds. In a recent construction project carried out in industry, a steel frame platform structure measuring approximately 3 m x 7 m was galvanized after welding fabrication. The structure was built of CSA G40.21 350W and CSA G40.20/G40.21 300W plain carbon steels and welded using a metal core arc welding process for the flanges and a flux core arc welding process for the webs of the beams. Due to their size, the platforms underwent a double-dip galvanizing process meaning half of the structures were submerged in the molten zinc path while the other half was exposed to the ambient air. This was repeated for the remaining side. Shortly after the galvanizing process was completed, numerous large cracks were found in the welded joints. Given there was no history of weld cracks after galvanizing in previous similar frames that were double dipped, this failure posed a new and curious problem."

Jan 1, 2017

By S. Khallouk, J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

Titanium aluminides recently replaced Ni-based superalloys as turbine blades in the last LP stage of aircraft engines. To extend their range of use at higher temperature their properties need to be improved, either by alloying or processing. An efficient solution is to reduce the grain size during the solidification process. In the first part of the paper, an overview is given on the possibilities for grain refinement of such alloys, based on literature data and new results. The most efficient grain refinement is obtained with boron addition which leads to boride formations that are detrimental for in-use properties of turbine blades. In this work, the use of the high grain refinement potency of inoculation with non-brittle particles has been used by developing new refractory-based inoculants. The effect of one of these inoculants on grain refinement of an as-cast structure in a Ti-46Al is presented; resulting in a reduction of the grain size by a factor of 3.While less efficient compared to the potency of boron containing alloys, the grain refinement is effective and does not introduce any embrittling particles.

Jan 1, 2015

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By Farzad Mohammadi, David Kratochvil, Patrick Littlejohn

"With more rigorous regulations being enacted in the mining industry, a need exists for cost effective and environmentally compliant technologies to remove selenium from mine impacted waters to ultra-low concentrations. Existing selenium treatment methods have high life cycle costs, introduce risks of acute fish toxicity, and produce biological waste residues that represent future liabilities. Furthermore, achieving selenium discharge limits of less than 4 ppb is a challenge for existing technologies. Selen-IX™ is a technology developed by BioteQ that selectively removes selenium from mine impacted waters to less than 1 ppb. The technology is purely physico-chemical and takes advantage of the basic principles of ion exchange and electrochemistry. Unlike conventional electrocoagulation that removes suspended solids and breaks emulsions or oxidizes heavy metals, the electrochemical process employed by Selen-IX™ relies on creating conditions where iron acts as a highly effective reducing reagent transforming selenium from a dissolved species into elemental selenium bound in a solid phase. The iron-selenium by-product of Selen-IX™ is an inorganic, non-hazardous and chemically stable solid. Due to their high iron content, the solids produced by Selen-IX™ are of interest to the steel making industry as a low cost feedstock. This offtake potential can not only reduce the life cycle cost of selenium removal by reducing disposal costs but more importantly, eliminate the risk of future environmental liabilities. In this paper, the basics of Selen-IX™ technology are presented along with results of successful piloting on streams from coal and copper-gold deposits.INTRODUCTIONVarious contaminants are released into mining wastewater during the extraction and processing of metals. One such contaminant is selenium. A naturally occurring element found in rocks and minerals, mining activities accelerate its release into the environment. Selenium in trace quantities is essential to all life forms but at higher concentrations it can be harmful, especially to aquatic life where selenium bioaccumulation can lead to reproductive deficiencies."

Jan 1, 2016

By Richardson A. H.

"IntroductionSafety and training in the mineral industry will always be issues that are hotly debated and discussed.The nature of the mining industry, where people and equipment work in close quarters deep below the earth's surface, attracts a great deal of public attention and concern, especially in the areas of safety and related training activities. This concern has been carried over into the mineral processingsector which is, of course, a vital part of the mining industry.It is therefore imperative that mining people closely examine the policies, procedures and programs presently in place to determine if they meet the needs of the industry and its employees. Everyone stands to benefit: the companies, employees and the mineral industry as an important segment of the Canadian economy.Phrases such as ""Safety First"", ""Safety is Number One"", have a role to play in industrial safety programs but in reality are a shallow approach to the magnitude of the challenge. An industry must produce its products in a cost-effective way, with good employee relations. None of these objectives can be successfully achieved unless accompanied by good safety performance. Accidents both on and off the job result in very poor efficiency, high costs and poor employee relations.This chapter, Safety and Training, outlines those major areas that the author believes are necessary components for an industrial safety, health and training program, but are not all inclusive. More will surely be added as additional problem areas requiring attention are identified. The major sections discussed are: Development and Implementation of a Safety Program; Occupational Health; Training; and Audit Procedures.The author has drawn on his experience as both a mill superintendent, mine manager and superintendent of safety, health and training. The approach developed at loco Metals Manitoba Division is frequently used in this paper with examples and excerpts to better illustrate the subject, but does not represent the full scope of programs in place in the Division."

Jan 1, 1989

By J. W. Reynolds

Use of crushed waste rock recovered by sink-float separation from normal ore production for backfill is an established procedure at Commco's Sulhvan mme, Kimberley, British Columbia. Need for a safe method of placement in voids which were difficult to reach by gravity methods led to a co-operative venture with Radmark Engineering Ltd. in the development of a workable pneumatic transportation system for rock material. This paper reviews work done to date in a current program, and includes comments on the nature of the fill so placed, options for cementing such fill, implications for other aspects of mining and references to other applications of the system by other organizations who exchanged experiences with the Sullivan mine staff during the five-year period reviewed.

Jan 1, 1972