Search Documents

By O. Babak, J. G. Manchuk

ABSTRACT A significant factor in evaluating bitumen recovery from an oil sands mine is the particle size distribution (PSD). Increased understanding of mined ore quality and improvement in predictions of recovery can be achieved through PSD modeling. This paper addresses PSD modeling using geostatistics. PSDs may be described using many discrete particle sizes, making this a challenge. The approach parameterizes PSDs with a few statistics. A lookup table is used to reconstruct the PSDs based on models of the statistics. The workflow is applied to Total E&P Canada’s Joslyn Lease and yields good results that reproduce input statistics without introducing artifacts.

Jan 1, 2013

By Lauri Gregg

Key Message Energy focused Change Management Process that engages operations managers is the missing tool needed to build capacity for energy/GHG management

May 1, 2007

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By T. V. Nethery

Introduction A brief account of the East Malartic fire is essential if this paper is to serve the purpose implied by its title. The fire originated in the timbers of No. 4 shaft at the 10th, or 1,570-foot, level; this was the top or collar of the underground sinking operations. At the time, sinking was in progress and the shaft bottom was 242 feet below the 12th station horizon, or 618 feet &apos;below the l0th level. Above the l0th level, the shaft was not in use as the surface plant was not yet completed. The shaft crews descended from surface in No. 3 vertical shaft to the l0th level, where they transferred to No. 4 shaft, a distance of 1,450 feet. Of the sixteen shaftmen mucking at the shaft bottom, four were able to reach safety. One shaftman was overcome by fumes midway between the two shafts on the l0th level, while attempting his escape. The remaining eleven men climbed as far as the 11th station and there succumbed to carbon monoxide. No. 4 shaft, inclined at 61 degrees, bad been raised and timbered from the 10th level to surface; this bad been followed by sinking operations below the l0th. Two air hoists had been set up in the footwall of the shaft, 110 feet above the 10th level, and directly behind compartments No. 2 and No. 4. The waste from the shaft bottom was hoisted in 28-cubicfoot buckets on mono rails and dumped over standard shaft sinking doors into waste chutes built into No. 1 and No. 3 compartments. The five-compartment shaft, 7 ft. 8 in. by 34 ft. 6 in. overall size, was heavily timbered. In addition to the standard shaft timbers of 8 in. by 8 in. and 8 in. by 10 in. B.C. fir, the hanging-wall and ends of the shaft were laced with 4-inch spruce lagging. This represented approximately 300 board feet of timber in placee for every foot of shaft. The cause of the fire bas never been determined, despite every effort to do so. The inquest held for those who lost their lives in the fire was an extremely thorough one, but only the location of the origin, and not the cause, was established.

Jan 1, 1950

By Kish. L.

"The results of a chemical and mineralogical study of eighteen opaque-oxide occurrences are discussed and the detailed chemical, metallurgical and mining feasibility study of a vanadium-rich magnetite deposit is summarized. A plot of the mol-percentages in the system FeO- Fe2O 3-TiO2 indicates that the deposits fall into two distinct groups: some contain hematite with ilmenite, and some others have magnetite with ilmenite (titaniferous magnetites). The plot also suggests that the two types of deposits were crystallized from liquids of different compositions. Each group has its distinct structural features. Vanadium is present in all of the studied specimens, however concentrations of economic importance have so far been found only in the titaniferous magnetite deposits. The vanadium content of the oxide concentrations of the Dore Lake Complex is the largest among the studied occurrences. Analyses of the concentrates of the drill-core sections show a compositional variation across the orebody; a continuous increase in the tenor of Ti02 and a decrease in the vanadium content upward in the layered sequence is found. Concentration tests on several tons of samples indicate that about 80 per cent of the vanadium is recovered in the magnetite concentrate."

Jan 1, 1972

By J. S. De Lury

The metalliferous areas of Manitoba have been described in more or less detail. Since the descriptions were written some new prospects have come to light and considerable mining development has taken place in two or three localities. No attempt will be made in this paper to give an account of recent activities or to describe the several areas in detail. In a general way, geological conditions are similar in all metalliferous areas of the province, a similarity that invites a discussion of the prospects as a whole, the features that are common to all deposits and the reasons for their uniformity. Modern theories of metallogenesis have a direct bearing on such a discussion and an effort will be made to show their application.

Jan 1, 1925

By M. M. C Jiménez, D. C. Buzzi, D. C. R. Espinosa, J. A. S Ténorio, G. F. R Oliveira

In this work the extractive and selective capacities of solvent extraction synergistic systems to recover nickel and cobalt were evaluated. The liquor used was from the high pressure acid leaching process (HPAL). Initially the industrial liquor, processed from lateritic ores, was analyzed to identify the concentrations of the metals. Experiments of synergistic solvent extraction were performed later. The extraction liquid-liquid was carried out with a mixture of Cyanex 272 (CY) and Ionquest 290 (IQ) extractants. The process was executed with the temperature of 65 ºC, pH of 5.2 and the ratio aqueousorganic 2:1. Systems of 80% kerosene and CY 20%, CY 16% - IQ 4%, CY 12% - IQ 8%, CY 8% - IQ 16%, CY 4% - IQ 16%, IQ 20% were studied during 20 minutes. The results of this paper showed that the mixture of these two extractants doesn’t improve significantly the recovery of nickel and cobalt from liquor.

Jan 1, 2014

By Gerald Blackmore

This paper discusses the present state and future trends within the coal industry, and then goes into the reasoning behind these planned trends. Such factors as marketing, costs, new mining techniques and machinery, and manpower and human resources are considered. Finally, the author refers to the effect that these trends will have on the coal industry of Cape Breton.

Jan 1, 1968

By Henry Lepp

Introduction A shaft sinking operation carried out at the Viking Yellowknife mine in the spring of 1947 presents certain features, especially as regards speed of sinking and low cost, that may be of interest to Institute members, and especially to those who are not familiar with conditions and costs in the Northwest Territories. After collaring, the inclined, two-compartment shaft was sunk 130 feet by four miners in twenty-eight days at a direct cost of only $53.19 per foot. All things considered, this is a remarkable performance, even if it does not actually establish a record. The property is at Morris lake, some forty-five miles north of Yellowknife. Formerly owned by Athona Mines (1937), Limited, it was acquired by the then newly incorporated Viking Yellowknife Gold Mines, Limited, in 1947. Surface work and diamond drilling in 1946 disclosed a number of veins and masses of quartz in a sill of diorite which lies conformably within sedimentary rocks. The sill strikes N.30°E. and dips at 70° to 85° southeast, and has a mean width of 40 feet over its explored length of 3,000 feet . Both the quartz and the diorite carry gold and are mineralized with pyrrhotite and lesser amounts of galena, sphalerite, chalcopyrite, and arsenopyrite. Of thirty-five holes drilled in the mineralized zone, the core from twenty showed visible gold. Sampling of drill cores indicated several ore shoots in the north and central parts of the sill. Assays, however, were somewhat erratic, possibly due to the fairly widespread presence of visible gold, and it was decided that the deposit could best be explored by underground sampling. Accordingly, late in 1946, plans were laid for the sinking of a shaft.

Jan 1, 1948

By J. V. Thirgood

"Reclamation legislation was introduced in British Columbia in 1969 amidst public concern and controversy. This paper reviews this legislation as it relates to coal mining, and how it is being implemented.Although the principles of land reclamation are reason-ably well understood, reclamation of industrial wasteland has never previously been attempted under such rugged conditions as occur in the Canadian Rockies and a new methodology is being developed.The resolution of the technical and organizational problems involved are discussed and the techniques and experiences described."

Jan 1, 1971

Despite the claims of energy efficiency and the considerable development that has gone into dramatically extending rolls? life and facilitating rolls? change-out, in the six years since the last SAG conference, only a few HPGR operations have entered the realm of mineral processing. Risk barriers to the take-up of new equipment or processes are: a massive increase in materials handling issues as well as in the number of pieces of equipment required, low total circuit potential energy savings, and similar or higher capital costs. An alternative route is to make use of the complementary strengths of the HPGR and SAG in hybrid circuits. Minimising materials handling issues, providing an ideal balanced feed to the AG or SAG mill, and improving controllability through shifting grinding load as the RoM feed changes, are all potential major advantages to this approach. Conceptual circuit layouts, based on real measured ore and equipment data, are presented here to illustrate the potential production upside, the reduction in operating costs and the reduction in the physical and energy footprints.

Jan 1, 2012

By M. Kalin

"Ecological Engineering and Biological Polishing technology is a decommissioning approach for inactive coal, uranium and base metal operations. To improve acid mine drainage water some fundamental aspects of wetland ecology and sediment microbiology are combined, to provide conditions to allow for biomineralization of the contaminants.This paper summarizes the first records of microbial alkalinity generation in acid mine drainage through the utilisation of the ARUM process. The process requires that the seepage is at pH 4.5 where sulphate reducers utilize sulphate to produce hydrogen sulphide, which in turn precipitates with metals. The pH increase is brought about by alkalinity generating microbes.The ARUM process has been successful in increasing the pH from 2.5 to 7.0. Flow through reactors operated in the laboratory continuously for more than 60 days have removed Ni from 13 mg/L to < 0.01 mg/L. Design parameters are being developed for low flow rates of 5 L/min in a test system receiving seepage from a tailings.1.0 INTRODUCTIONAcid mine drainage associated with mining wastes poses a significant environmental problem. Conventional means to treat acid mine drainage (AMD) use chemical treatment system. Ecological Engineering technology uses natural biological means to curtail and ameliorate AMD during mine operations and at the time of decommissioning. The premise underlying Ecological Engineering technology is that AMD is the result of a natural process enhanced by mining activities. Therefore, in nature, a process providing a natural balance to AMD has to exist, which, when assisted through appropriate means, can counteract the detrimental effects of AMD on the environment. This process is microbial alkalinity generation which is known to occur in wetlands, lake and ocean sediments (Baas Becling et al, 1960)."

Jan 1, 1991

"5.1. IntroductionThe sample preparation requirements for bulk analyses of platinum-group elements (PGE) are different from the requirements for ore microscopy and in-situ analyses. It is necessary that the initial sample collection results in as representative a sample as possible for both types of analyses. Ingamells (1980) believes, however, that sampling is always imperfect and that there is no such thing as a truly representative sample. Once collected, the usual low content and irregularly dispersed nature of the PGE require that samples for bulk analyses be made as uniform as possible, whereas in samples for ore microscopy and in-situ analyses the PGE must be concentrated. Because of the generally high specific gravity of platinum-group minerals (PGM), certain precautions must be taken, such as mixing the sample material in the bags prior to opening.5.2. Preparation forBulk Analytical MethodsThe principal factors that determine the size of the sample required for a bulk analysis are grade, heterogeneity and grainsize. Initially, the grade and sample heterogeneity can only be estimated and a sampling methodology is developed with experience. It is essential at all times, however, that the assayers have information about the source of the sample and the purpose for the analysis. Information on the grain-size, which can only be obtained through mineralogical analysis, is also very important for PGE analyses, but, unfortunately, is often ignored.5.2.1. Samples fromUnconsolidated DepositsConcentrations of PGE may occur in eluvial deposits as well as in a large variety of alluvial deposits, including those of fluvial and glaciofluvial origin. These deposits are often difficult to map and sampling is further complicated by the wide range, from sand-size to boulders, of the non-POE-bearing constituents, and by the irregular distribution and shape of the ""pay streaks"". PGE concentrations in unconsolidated deposits are largely composed of resistant Pt-Fe and Os-Ir-Ru alloys (cf. Cabri and Harris, 1975 and Raicevic and Cabri, 1976), thus making comminution to the usual-150 to -200 mesh somewhat unreliable, due to the malleability of these alloys."

Jan 1, 1979

By P. W. Billwiller

Abstract The Britannia Mining and Smelting Company, Limited, have replaced diamond drills with percussion drills and tungsten: carbide bits for most of their blast hole drilling operations and have thereby reduced ore breaking costs. Two-inch Carset bits .are used, with one-inch hexagonal Atlas Chippewa alloy steel in 3-foot .and 6-foot lengths. Locally made couplings of Atlas SPS 245 alloy steel connect the rods. The machines used are 31½-inch automatic leyners with lugged or anvil block chucks. For drilling holes below the horizontal, the lugged machines with special adapter rods made from 114- inch solid round Atlas SPS 245 are required. These rods are lugged at one end and a water hole is drilled for six inches into the other end. Over this rod is placed a water swivel which permits the water or air to be sent directly into the steel. A decreased cost per foot, increased footage per shift, and the use of standard equipment and crews are some of the main advantages of tungsten carbide drilling over diamond drilling. Introduction Long-hole drilling with percussion drills and sectional steel was introduced in several American mines some twenty-five years ago. It did not prove very successful, however, because the rapid gauge loss in steel bits necessitated the use of very large starter bits. This in turn rapidly fatigued the straight carbon-steel then in use, made it difficult to maintain the couplings, and resulted in a slow drilling rate. The introduction of the tungsten carbide insert bit and alloy drill still has changed this picture and opened real possibilities for the application of percussion drills to blast-hole drilling. If this type of bit had been perfected ten years ago, much of the research work and experimenting done to apply diamond drills to ore breaking would have gone toward developing the application of the tungsten carbide bit to this problem.

Jan 1, 1950

By J. D. Allan

"IntroductionThe purpose of this paper is to present a general picture of the Lynn Lake nickel area of northern Manitoba. The geology of the area will not be discussed in great detail, nor will the mining op; rations presently being conducted. Both subjects will be treated briefly and, in addition, mention will be made of some of the problems encountered in mapping in the area. some of the questions which still remain unanswered, methods of prospecting that have been applied and the future possibilities of the area.For present purposes, the Lynn Lake area will be considered as extending from west of Lynn lake to east of Barrington lake. Thus, more correctly, it should be termed the Lynn Lake-Barrington Lake area. It comprises five 15-minute map-areas, or a total of 800 square miles, in a block 47 miles east-west and 17 miles north-south.Lynn lake itself is about 120 miles north of Sherridon, Manitoba, the closes t rail terminal. The area is part of the Granville Lake sheet which was mapped by the Geological Survey of Canada in 1932, 1933, and 1935, the results being published in Summary Report 1933. Part C, and as Maps 343A and 344A on a scale of four miles to o.ne inch. In 1940, the McVeigh Lake area was mapped by the Geological Survey of Canada on a scale of 1,500 feet to 1 inch and a map was issued in 1945."

Jan 1, 1950

By H. Tetu, F. Pells

"The copper-molybdenum property of Brenda Mines Limited is located in the Okanagan district of British Columbia, approximately 25 miles west of Kelowna. The Okanagan Valley is a resort and fruit-growing area, and therefore pollution control measures are more stringent than in some remote areas.The Brenda plant began production in April 1970 and is operated at a rate of 24,000 tons per day. The plant site is located at an elevation of 4,800 feet, which is approximately 3,600 feet above the level of Okanagan Lake. The site is in the Okanagan drainage basin.The major consideration in the design of the system was the prohibition of any downstream discharge. It was therefore necessary to redaim as much water as possible and to minimize the addition of fresh water to the system. The maintenance of a water balance is of critical importance.This paper will outline the major design criteria for the systems and the site investigations which were carried out. The design and construction of the facilities will be de-scribed and current operating experience will be outlined."

Jan 1, 1971

By Bob Robinson

In 1990, the European Space Agency (ESA) initiated a technology transfer program to stimulate the wider use of technology developed by the European and Canadian space communities. This paper focuses on the method of technology transfer from the space industry to terrestrial industries, with a focus on the mining resource sector within a program called the Harsh Environments Initiative (HEI) created in 1997. Other resource sector applications include forestry and oil & gas. C-CORE in partnership with the Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) supported by ESA, Canadian Space Agency (CSA) and European R&D organizations conduct projects to promote and demonstrate the transfer of innovative technologies from space to non-space industries. Space programs have and continue to develop new knowledge for extra-terrestrial application, e.g., satellite earth observation, manned missions and unmanned planetary exploration. Many of which hold the potential for application on land and ocean. Currently, space technologies of interest to the mine sector range from robotics and image analysis to sensors, software and advanced materials. The HEI works to identify and apply these types of technologies in the areas of automated/tele-controlled mine operations and mine monitoring.

May 1, 2001

By David Forrester

"At the 95th CIM Annual General Meeting in Calgary, 1993, a paper entitled “Progress on Futuristic Mining Technologies” was presented(Matthews and Sarin), in which they outlined the goal of continuous excavation of hard rock and some of the technologies being developed to achieve it. The subject continues to be featured in periodic reviews and articles in the literature, (Gertsch, 1994; E&MJ, 1995). Matthews and Sarin note the considerable success of the development and application of continuous mining technologies in the soft rock under-ground mining industry, especially those in coal and potash, with major benefit to overall production, productivity and economic viability. It is the belief that similar achievements can be realised in the underground hard rock mining which continues to drive the development of hardrock continuous mining technology.This overview has been prepared specifically for this issue of the CIM Bulletin. It attempts to tie together current advancements in continuous mining in soft rock (where remote control and automation are already well established) with the background and status of development in hard rock continuous mining. Following a brief review of key factors and machine types, soft rock aspects are discussed, then a more detailed review is given of hard rock technology, with particular reference to Canada’s HRDK Mining Research Ltd. and their key role.The mining industry has long been at the forefront of technology development, for example, the application of the early steam engine to reach reserves at greater depth for dewatering mines in the industrial revolution. By necessity, the individual characteristics of seams and orebodies dictate the mining method, continually presenting mining engineers with new challenges. One of these is the extraction process itself and the goal of replacement of the drill-blast-muck cycle by continuous excavation. Very soft rocks have always been mineable using some form of cutting, even with primative tools. However, as the challenge has been taken up, technologies have evolved to steadily increase the hardness of rock that can be mechanically excavated. It may surprise some readers that at least three machines have successfully cut and loaded rock with an unconfined compressive strength (UCS) of 250 Mpa to 300 MPa (36 000 to 43 500 psi) in field trials (Table 1)."

Jan 1, 1996

By E. Allen

Quebec Cartier Mining Company operates approximately two hundred and fifty pieces of equipment in a climate with a temperature that has averaged 27.5°F during the last seven years. The use of special-purpose lubricants, fuels, antifreeze, rubber compounds, and alloy steels have reduced the cold-weather hazards. In some areas, high-cost cold-weather protective heating devices are being eliminated with experience.

Jan 1, 1966

By K. L. Azinger

Successful relationships between mining companies and local stakeholders are now an essential part of the social contract of “doing business” (Prescott, 1995). The methodology presented in this paper is designed to assist mining companies in understanding and building relationships with diverse stakeholder groups. The methodology starts by recognizing that mining projects have a natural life cycle which can be used to identify when new external affairs strategies are required. In designing an external affairs strategy, the first step is to set objectives that are compatible with the overall objectives of the mining project. The management team then identifies the main stakeholder groups and seeks to understand the priorities and inter-relationships of the individual stakeholders. The result of this stakeholder analysis is an understanding of the Degrees of Influence of each of the stakeholder groups along with a relationship map which illustrates the strong interactions between stakeholders. The company is then prepared to take a proactive approach to building relationships with the primary stakeholders. This methodology was developed by BHP to assist with the federal government environmental approval process for the development of Canada’s first diamond mine. BHP has successfully used the methodology in three different phases of the NWT Diamonds Project and is now applying the methodology to mining and development projects around the world.

Jan 1, 1998