Search Documents

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

By J. Nesset, F. Rosenblum, P. Spira

Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 500°C. However, most concentrates show little or no propensity to self-heat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.

Jan 1, 2001

By Richard Jundis

At the Vale Inco Ontario Operations, the working environment is rapidly evolving with organizational changes, new business systems and software tools. These changes are required in order to meet today?s challenging business environment. Mining professionals are focusing on the development of safe and achievable mine plans to maximize mining value while reducing the potential of project delays and production shortfalls. This paper explores how new design tools, techniques and system designs in mine planning are being developed to optimize the value of every ton of ore mined and processed. To differentiate from other papers on long-term planning, this paper focuses on the concept of business planning at the mines. Business planning is the understanding and optimization of the relationship between mine plans and the value it adds in the overall process. The management and key stakeholders of Vale Inco have recognized that the development of a robust mine planning system and programs are essential for the long-term sustainability of the operations.

May 1, 2009

By Samantha Beeson, Collin Poole

"This paper examines the development of two new selective flocculation techniques for recovering KCI values from low grade carnallite potash ore.Direct recovery of KCI was achieved using one of two mid-range molecular weight polymers, one non-ionic and the other strongly cationic, in conjunction with the same selective anionic dispersant. From initial response studies on pure minerals and selective flocculation tests on synthetic mixtures, investigations were extended to recover KCI values from a natural carnallite potash ore. A single-stage process achieved products grading up to 61.3% KCI at recoveries up to 85.4% for the cationic flocculant suite and up to 64.8% KCI with recoveries as high as 90.3% for the non-ionic flocculant suite, with dispersant and flocculant dosages of 150-250gr1 and 10-75gr1, respectively. These results clearly demonstrate not only the feasibility of treating such problematic ores at low reagent dosages, but also the potential elimination of desliming prior to froth flotation.The experimental results presented are considered in terms of the reagent adsorption phenomena present in the system and various aspects of floe formation and cleaning.IntroductionAs high-grade sylvinite potash ores become scarce, lower grade sylvinite and carnallite potash ores are becoming more attractive. However, these ores often contain large amounts (up to 15% by weight) of water-insoluble slimes which must be removed prior to KC! flotation, owing to their high adsorptive capacity for the amine collectors used. The slimes are generally removed by scrubbing followed by hydroclassification and any residual material not eliminated is blinded with reagents such as guar gum or starch to inhibit interference in subsequent KC1 flotation.An alternative approach used commercially in Canada by Agrium Inc. involves water-insoluble slimes flotation prior to KC! flotation. In this process, the slimes are selectively flocculated and then separated by froth flotation. Losses of KC! to the slimes product and associated brine requirements are both reported to be less than those encountered in conventional desliming, but the technique is somewhat limited in its application at present."

Jan 1, 1997

By C. J. Havard, G. C. Taylor, D. G. Cook, N. C. Ollerenshaw, D. K. Norris

"The area encompassed by this report is the eastern and northern Cordillera, shown on the composite map accompanying these background papers. It extends from the 49th pm•allel to the Arctic Ocean and from the Rocky Mountain and Tintina trenches to the Interior Plains. The Mackenzie delta is included in the discussions because of the implications of the bedrock geology of the Arctic Plateau and Coastal Plain on the hydrocarbon and mineral potential beneath it.The eastern and northern Cordillera forms the back-bone of the Western Canada sedimentary basin and from it most of the principles of orogenesis and epeirogenesis relating to the understanding of the structural, depositional and fossil record of the basin have been derived. It may be divided roughly into two parts, reflecting basic differences not only in structural style but also in mineral potential. The more easterly and younger rocks generally contain hydro-carbons, coal and non-metallic minerals; the more westerly and older rocks contain metallic and industrial minerals."

Jan 1, 1970

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By M. Gaumont, F. Robichaud

"Agnico Eagle Mines Limited (AEM) is a Canadian-based gold producer with operations in Canada, Finland and Mexico. In 2010, AEM produced its first gold bar in Nunavut, Canada as it started its Meadowbank operation. It is also in 2010 that AEM acquired the Meliadine property, which is located 25 Km North of Rankin Inlet, Nunavut, Canada. The Meliadine gold project is an advanced exploration and development project, comprising of workers camp, underground and open mines, a processing plant and all the services facilities and infrastructures required to sustain operation in a remote arctic environment.Pending formal board approval, production start-up is planned for Q3 2019 and the process flowsheet is based on an ore processing rate of 1.1 million dry tonnes per year (3,000 dry tonnes per day from underground mining) for the first three years, and 1.98 million dry tonnes per year (5,000 dry tonnes per day from both underground and open pit mining) for the remaining years at 92% process plant availability.To the end of 2015, more than 45 metallurgical test programs have been conducted on the Meliadine deposits. Based on the results of these programs, an optimal gold circuit was designed, comprising of crushing, grinding, gravity separation and cyanide leaching with a carbon-in-leach circuit (CIL), followed by cyanide destruction and filtration of the tails for dry stacking. The assumed gold recovery for the reserves averages 96.0% at a 7.44-g/t gold average mill feed grade."

Jan 1, 2016

By Stephen R. Grano, Jon Glatthaar, Philippe Steinier, Christopher J. Greet

"The importance of the oxygen content of sulphide mineral pulps in determining which reactions occur, and their subsequent influence on flotation behaviour is grossly underestimated in most operating concentrators. While pH is routinely monitored, Eh and dissolved oxygen measurements are obtained infrequently. However, dissolved oxygen measurements in conjunction with other pulp chemical parameters (i.e. pH, Eh, and EDTA extractable metal ion analysis), can provide valuable insight into where and what type of reactions are occurring within a circuit. Unfortunately, these readings yield “instantaneous” measurements of the pulp chemical parameters.What is needed is a means of establishing how reactive a pulp is, and how this reactivity changes as components of the system are manipulated. Oxygen demand provides an opportunity to do this. Several attempts at measuring the oxygen demand of a pulp have been made in the past with varying degrees of success. Most notable among these are Noranda and BOC Gases.Learning from these experiences, Magotteaux have developed the MagO2 ® demand vessel to measure the oxygen demand of mineral pulps. This paper described the apparatus, and through a case study on Broken Hill lead/zinc ore demonstrates how the MagO2 ® demand vessel is used.INTRODUCTIONThe role of oxygen in flotation is complex. While a considerable body of work exists demonstrating the strong involvement of oxygen in the interactions between sulphide minerals and collector (Gaudin and Finkelstein, 1965; Gaudin, 1974; Woods, 1984; Laajalehto, Nowak and Suoninen, 1993), the presence of oxygen can also affect the oxidation state of sulphide and non-sulphide minerals, which can impact on their flotation behaviour. Further, sulphide mineral oxidation is related to their oxygen demand (Spira and Rosenblum, 1994)."

Jan 1, 2004

By M. W. Wadsley

"Physical and chemical property models are widely used in process engineering. There exist, in the published literature, completely empirical models of ''thermodynamic properties"", that is, property models that are not consistent with the laws of thermodynamics. There also exist property models that purport to be thermodynamically consistent but are flawed in their implementation. There are also published property models that are consistent with the laws of thermodynamics but that do not reproduce property values with an acceptable accuracy. A practicing engineer might be asked to assess very different property models for which there are a variety of claims. This paper discusses features of thermodynamic and empirical property models that may assist in their practical evaluation and implementation."

Jan 1, 2005

By S. Perez

Core drilling is a fundamental process in the mineral exploration industry. As deep exploration in hard rocks is accelerated due to the depletion of near ground mineral resources, deep-drilling operations need to reduce their reliance in operators experience and begin to implement new technologies in order to increase efficiency and cost-effectiveness of the overall process. Currently, lack of real-time information on the bit/rock interaction is a major problem. Therefore the mechanism behind the acoustic emission, which is a proven technique for remote monitoring, generation in mechanical rock cutting must be understood in order to provide real time information about the rock. This paper aims to identify the influence of mineral composition of granitic rocks on the acoustic emission (AE) during rock abrasivity test with a single contact tool and to evaluate the feasibility of AE as a means to infer Cerchar Abrasivity Index (CAI). Single contact tool will provide precise and accurate description of the source of AE. To provide constant grooving speed Cerchar apparatus was modified to monitor AE during rock/tool interaction. Tests on the modified Cerchar apparatus are carried out under the static load of 70N and cutting speed of 1 mm/s. A Scanning Electron Microscope (SEM) is utilized to visualize the groove in the rock and to identify the mineral composition through Back-Scattered Electrons (BSE) reflected from the rock sample. Based on the microscope images, it was found that biotite shows a larger groove area and plate-like fractures accompanied with burst-type AE signal, whereas plagioclase and quartz, which are characterized by similar hardness and BSE brightness, possess shattered-like fractures and more continuous-type AE signals. In addition, a-value of the Gutenberg-Richter scale has been found to well correlate with Cerchar Abrasivity Index (CAI).

Jan 1, 2015

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By J. A. Finch, T. Weber

"Bubble size in flotation is strongly influenced by frother concentration in the pulp liquor. There is no accepted method of judging the dosage and thus how effectively frother is being distributed to control bubble size is not known. This will hamper certain plant test work where constant bubble size (e.g., when comparing reagents) is implicit. Bubble size is not easy to measure in plant and gas holdup is suggested as a surrogate in the development of a proposed “meter” to estimate frother concentration. The meter is calibrated to enable frother concentration to be estimated on samples drawn from any location in the flotation circuit. The meter and its calibration are described.As general background the action of frothers in reducing bubble size by retarding coalescence is discussed and the bubble generation systems for which the effect will be important are considered.INTRODUCTIONBubble size is an important variable in flotation. The flotation rate constant k has been related to mean bubble size Db by k % Db -n with n ranging up to 2 (Ahmed and Jameson, 1989) and even 3 (Yoon, 1993). Recent work has introduced k % Sb, the bubble surface area flux, given by Sb = 6 Jg / Db (where Jg is the superficial gas velocity or volumetric gas rate per unit cell cross-sectional area), i.e., n = 1 (Gorain et al., 1998). Regardless of the exact value of n, the significance of bubble size in flotation remains. In many plant trials it will be implicit that bubble size has not changed and attention will focus on other process variables. The measurement of bubble size, or a surrogate, would be useful addition to any test work.The size of the bubbles is influenced by several variables, gas rate, gas injection system (e.g., impeller design and rotation speed in a mechanical cell) and pulp composition (chemicals added, percent solids), but the most important is frother concentration (Harris, 1976). The frother functions by retarding coalescence (see appendix), which acts to preserve the small bubbles generated in the pulp (and permits a stable froth to form on top of the pulp). The measurement of bubble size is thus related to measuring frother concentration. The distribution of frother and whether sufficient (to control bubble size) is reaching the intended parts of the circuit then become important considerations. At present there is no simple way to judge frother concentration in a plant. In this communication we introduce a possible methodology, a “frother concentration meter”."

Jan 1, 2003

By B. K. Gorain, A. W. Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimization of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimization, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterize cell hydrodynamics, gas dispersion properties, froth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimization of the Red Dog flotation circuit. IntroductionThe traditional methodology for flotation scale-up and plant design is based on the ruleof- thumb with safety factors and dimensionless hydrodynamic group similitude considerations. With the recent trend toward larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-ofthumb and trial-and-error, the probability of failure would then increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimization of the circuit to meet its metallurgical target. This results in a plant design, which may be incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2003

By B. S. Ignasiak, B. N. Nandi, D. S. Montgomery

The growing need to measure the extent of weathering of coking coal in storage and in transit prompted the comparison of the dilatation of coking coal on heating, which is known to be a sensitive index of oxidation, with the composition and volume of the gases produced by a mild pyrolysis of the same coal. It was found that the pyrolysis method had the advantage in that it could be used to study coking coals in advanced stages of oxidation, when the swelling properties had been largely destroyed. Of the various constituents in the pyrolysis gas, the most sensitive indication of coal oxidation was the volume of carbon monoxide evolved per gram of coal. For the coals examined, this index appeared to be at its best when the temperature of pyrolysis was approximately 35oC.

Jan 1, 1970

By A. Demers, M. Chapman, N. Reynier, R. Lastra, M. Courchesne, C. Laviolette

Historic medical isotope production at Canadian Nuclear Laboratories (CNL) in Chalk River involved the dissolution of irradiated isotope targets prior to extraction of Mo-99. This process generated liquid waste that was cemented in 5-gallon containers and transferred to an outdoor waste-management facility for intermediate storage. Research was undertaken to develop an innovative method for uranium, mercury and cesium recovery from the radioactive cemented waste (RCW). Regulations prohibit the removal of active radioactive waste from the Chalk River facility. Thus, CanmetMINING produced surrogate material following the same procedures and conditions to those used at CNL. The selective recovery of the uranium from the surrogate radioactive cemented waste (SRCW) could offer CNL more disposition options for the resulting wastes. Leaching tests were performed using four different SRCW at 1 kg scale. Different conditions, operating parameters, and the presence of plastic and corrosion products were evaluated on solubilization. The research investigated the use of potassium iodide with the sulphuric acid leach to increase metals recovery. Iodine improves the solubilisation of metals and the U dissolution reached 99%. The increase of leaching time reduces the U solubilization due to silica gel formation. Therefore, it will be important to control leaching time to avoid the loss of U during the pilot scale experiments. For Hg, the solubilization ranged from 60 to 80% due to the presence of metallic mercury and mercury sulphide found in SRCW cured at 60°C and/or aged for 30 months. Ion exchange (IX) was found the best method to separate the uranium from the impurities and produce a purified and concentrated uranium solution suitable for yielding a uranium product (yellow cake).

Jan 1, 2020

By Laura Mottola

This paper outlines a framework for ensuring the success of the implementation phase that follows research and development of new mining technologies and systems. It is based upon recent and past lessons learned that have demonstrated the critical challenges to effective technology transfer, which frequently receive inadequate attention within the culture of the mining business. The paper focuses on mining automation implementation challenges and then outlines a Roadmap which is proposed as an integrated framework to deal with the key aspects of people, process and technology. This framework is built upon: assembly of a Strategic Team to develop a Roadmap; fully understanding the business requirements of the technology initiative; defining Key Performance Indicators in a Balanced Score Card; performing a Stakeholder Analysis to identify the affected groups; and finally developing a master Project Plan to execute the Roadmap.

Oct 1, 2009

By Jeremy G. Berg, James B. Mulligan

"There is a very small fraction of wireless experts in the world with experience in underground installations and an even smaller fraction that have experience specific to building mine shafts. This is why in 2009, Redpath created its own system to meet the demands specific to shaft construction. Today, after a dozen shaft installations and several design iterations, Redpath has the expertise and experience required to implement a proper wireless system in any shaft configuration.This document will explain multiple proven wireless communication designs optimized for shaft construction and suitable for permanent use. This includes line of sight installations up to 1200m, short range mesh networks, and the latest patent pending Integrated Leaky Feeder Mesh Network. Additionally, this document will explore the lessons that Redpath learned in its effort to interconnect the people and tools needed to build a mine shaft.INTRODUCTIONAfter a decade of research, several design iterations and a dozen application examples, Redpath has resolved two wireless network architectures to best serve mine shaft construction projects.The long range line-of-sight (LOS) wireless network is the most cost effective and easiest to install, but requires an unobstructed line of sight between the working area and the shaft collar. As such, long range LOS is best suited for ventilation shafts or during the first phase of shaft sinking, before the shaft is equipped.Alternatively, a mesh network uses radios installed at pre-determined intervals in the shaft and on each conveyance. A wireless mesh uses antennas to bridge intervals between shaft radios, whereas Redpath’s integrated leaky feeder mesh network (patent pending) bridges these intervals with radiating cable, commonly referred to as a “leaky feeder” cable. Both of these mesh configurations can provide continuous reception for hoist conveyances travelling in shafts without line-of-sight, making them ideal for shaft equipping and even permanent installations in both mine shafts and lateral drifts.BACKGROUNDHoist operators receive operating commands using what are commonly referred to as “bell signals.” These instructions are delivered in a series of coded pulses on a spring returned pull cord or push button that is typically hardwired back to the hoist operator’s control room from one of many locations in the mine shaft. During the construction phase of a traditional mine shaft, a worker riding inside the sinking bucket would have to reach out to a pull cord installed on the shaft wall to send a stop command to the hoist operator. Today, Redpath’s modern shaft sinking projects use fully enclosed personnel carriers to protect the workers riding inside, specifically preventing workers from reaching out into the shaft while the hoist is in motion. The enforcement of this safety feature on all shaft projects in 2008 forced the engineering group at Redpath to find a suitable wireless solution for hoist communication to facilitate shaft construction.THE IDEAL COMMUNICATION SYSTEM FOR MINE SHAFT CONSTRUCTIONIdeally, the shaft communication system should not transform the tools to which the miners have grown accustomed. It should support the push-to-talk functionality of traditional VHF handsets and the standard belling system that has been used for decades. Additionally, it should be able to support a vendor independent framework upon which new devices and features can be added. The following paragraphs summarize some of the important requirements Redpath has identified.Support for voice transmission: Low latency is critical to prevent jitter during voice transmissions. The system must be compatible with commercially available mobile handsets and support several simultaneous conversations with the ability to broadcast a voice message to all users on a select channel using a “push-to- talk” microphone and loudspeaker.Transmission of PLC data: Low latency is required to"

Jan 1, 2019

By G. Belzil, F. Robichaud, M. Fullam

ABSTRACT The Goldex mining and milling complex is operated by Agnico-Eagle and is located in the Abitibi greenstone region of northwestern Quebec, Canada. Commercial production started in 2008. Average gold recovery is 93.5% with approximately 68% of gold recovery coming from the gravity circuit. During the first three years of production, three gravity audits were carried out to optimize performance of the gravity circuit. This paper presents results of the audits and the development of a model linking gravity and overall gold recovery, and outlines improvements made to increase gravity performance and reduce operating costs.

Jan 1, 2013

By K. Bruce Hodgins

The North American mining industry faces challenging emissions regulations in coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable. Westport Innovations Inc., of Vancouver B.C. has developed high pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications, reduced emissions of NOx, PM, and CO2, with no loss in performance. This is accomplished through late-cycle high-pressure injection of natural gas directly into a diesel engine combustion chamber. The natural gas is injected at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the main natural gas fuel injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, low speed torque, high-power output, no engine knock and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored in a similar manner and volume to diesel fuel by virtue of its increased energy density over compressed natural gas. Cummins, Inc. of Columbus, Indiana and Westport have formed a joint venture, Cummins Westport Inc. (CWI), under which agreement the HPDI technology is being applied to a Cummins QSK engine series for high horsepower applications such as mine haul trucking. CWI, along with Komatsu Mining Systems, ENRG Fuels, Placer Dome, and Cortez Joint Venture are performing a feasibility study for the development and demonstration of an LNGfueled HPDI QSK engine in a large mine haul truck. The goal would be to demonstrate low emissions consistent with EPA ?Blue Sky? standards, high efficiency based on HPDI technology and good economics resulting from the high fuel consumption of 2,000+ hp trucks.

May 1, 2002