Search Documents

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By Dave Bulled, Jim Thompson, Tim Leriche, Mark Blake, Troy Wilkie

"A commitment to a core testing, plant modeling and reconciling technique has shown substantial economic benefits to IOC in terms of accurate production forecasting, smoother operation of the mill, improved expectations of throughput and co-operation across production departments from geology, planning, mining, and processing, to shipping of concentrate to market.This paper describes a successful seven year program of forecasting throughput of the autogenous milling circuit at the Carol Lake concentrator of IOC. Work started with audits of the grinding circuit in 2001 and benchmarking of the data collected from samples of mill feed and plant operation to the CEET mill design and throughput forecasting model.Initially 390 drill core samples were tested for SAG Power Index (SPI) to measure the energy required in milling, and the data distributed using a geostatistical technique across the two operating pits, so that hardness was estimated in each of the 40,000 blocks (or 1500 million tons) of potential ore. In 2004 a forecast of energy requirement, i.e. forecast of throughput for a given power availability at the mill, was produced for each ore block using the CEET model and used for mine planning to smooth plant throughput. The forecast for blocks mined on a monthly basis was reconciled with plant results over the next 2 years and minor changes made to the CEET model. The forecasting exercise was repeated in 2006 and in 2008 with the latest model based on the testing of almost 1300 samples of drill core at closer spacing.INTRODUCTIONThe contracting of sales to clients and the timely supply of products to meet those contracts is a cornerstone of good business practice. Ensuring the correct scheduling of production is a major concern of mining companies where the supply and qualities of the raw material is uncertain and production facilities are not flexible. This is particularly challenging when the product is of high volume and produced far from the customer, such as iron ore.Apart from the metal content of the ore being mined, the greatest impact on production scheduling is the throughput of the comminution section of the extraction plant; most notably when size reduction is achieved by autogenous grinding. The response of the mills to variability in the hardness of the ore can change throughput by as much as 50% from day to day at some plants."

Jan 1, 2009

By Patrick F. R. Murphy

An ultra-low profile LHD has been developed by EJC Mining Equipment of Burlington, Ontario for narrow-reef mining applications. This paper discusses the challenges encountered during the evolution of the machine's design and subsequent field testing. Continuing research and development focuses on optimizing machine performance and controllability, reducing emissions, and enhancing maintainability. Details will be given on field trial experience and ongoing test work being carried out at the manufacturing facility.

May 1, 2004

By D. Shen, J. Cheung

Variable reactance arc control by the SPLC (Smart Predictive Line Controller) has been installed at many different mining sites and steel processing plants around the world. Since its first installation 18 years ago, many advances have been made to both the technology, and to its integration with furnace processes and plant operations. The SPLC has helped to improve electric arc furnace stability by reducing electrode movement while maintaining flat line arc power. Stable furnace operation at higher average power increases productivity. This paper summarizes the progression of electro-technology at Hatch since the 1970s, including fixed and variable reactance, digital electrode regulation, and fast variable speed hydraulics for Soderberg electrode, as demonstrated and benchmarked through projects and lessons learned over the years.

Jan 1, 2015

By Andre L. De Vegt, Cees J. N. Buisman

"For the past eight years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps:1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates.2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur.Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m3/d. A test program, utilizing a large scale pilot plant, will commence in November 1995 at a copper mine in the U.S.A. to remediate groundwater contaminated with sulfate and heavy metals. Biological reactor performance and selective metal recovery will be studied. Sulfur dioxide (S02) can be removed from fluegas using a combination of scrubber technology and the two biological steps. The end product is elemental sulfur. A commercial size biological desulfurization plant has been in operation since July 1994 treating 50,000 Nm3/h of fluegas. Sulfide can be removed from mining waters or anaerobic wetlands using a THIOPAQ® Sulfide Oxidizing reactor.lntroductionSulfur can be present in various water and gaseous streams in a mining operation. In many cases the sulfur compounds have to be removed because of toxicity, corrosive properties and contribution to acid rain. Mine waters can contain dissolved heavy metals. An efficient way to remove dissolved metals removal is the precipitation as metal sulfides. Paques has developed and installed treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. These treatment systems biologically convert sulfate to hydrogen sulfide (H2S) which can be used in heavy metal precipitation. Excess H2S is biologically converted to elemental sulfur. This paper provides an overview of these newly developed biotechnological treatment systems."

Jan 1, 1997

By K. Mikulash

"Agnico-Eagle Mines Limited is located at Joutel in North-Western Québec. The mine is about four miles north-west from the town on the left bank of the Harricana River. The present mining is 1,800 feet deep with an extensive geological development below this level.HISTORY The development of the ore body started sometimes in 1967 and then the operation ceased in 1969 and again reopened in 1973 due to higher prices of gold. During these periods of active development, a considerable metallurgical research has been done by different laboratories and research and design companies.The original capacities of the Mill differed as much as 30%. So did the concept of the ore treatment. The original design of the mill was for 200 TPD of ore with straight cyanidation. The problems with low gold extraction, high reagent consumption and poor filtration resulted in a decrease of the expected mill output to an initial 550 TPD with gold recoveries in the order of 40 to 60%.Although the studies and research work done on the ore varied, all of them had a common conclusion: a very fine grind is needed to expose gold. The mining method (sub-level blast hole mining) now provides the ore that differs from that on which the metallurgical test work was conducted and the original capacity calculations had been done.These variations in the concept consequently led to the conclusion that the size of gold is a determining factor for the process.Kilborn Engineering provided the original design with the Leslie Eng¬ineering completing the design. The metallurgical test work has been done by the Department of Energy, Mines & Resources, Lakefield Research of Canada, Kilborn Engineering and Sidam Incorporated.The new flotation section with secondary grinding has been designed and put into operation by the company in December 1975 with the results yet to be evaluated."

Jan 1, 1976

By George H. Hope, Steve Ciccone

"The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day ice-free shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction.INTRODUCTIONThe Red Dog Mine, which began operations in 1989, is located above the Arctic Circle in Northwest Alaska, approximately 145 km north of Kotzebue (Figure 1). An 80-km road connects the mine site to the DeLong Mountain Transportation System (DMTS) port site. Red Dog is the largest known zinc deposit in the world, with known reserves totalling 94.5M tonnes, and is the largest zinc producer with a concentrate production rate of more than 1.1M t/yr.Open-pit mining is by typical drill, blast and load operation using moderately sized mining equipment. Ore is processed through conventional crushing, grinding, and flotation to produce separate lead and zinc concentrates. Filtered zinc and lead concentrates are trucked year-round to the DMTS port site, where they are stored in two A-frame buildings, 330 and 440 m long. A lightering barge system is used to transfer concentrate from the shallow water load-out to deep-sea vessels anchored approximately two miles offshore. Shipping is limited to a 100-day, ice-free window beginning in early July."

Jan 1, 2003

By M. Helinski

In the authors? experience inappropriate water management in hydraulic fill masses has been the root cause of most barricade failures. Inappropriate water management can lead to high water pressures, reduced effective stresses and increased barricade stresses (Kuganathan 2002). In addition the high hydraulic conductivity and non-plastic nature of most hydraulic fills makes susceptibility to piping failure (Cowling et al. 1987) a high possibility in many hydraulic backfills where a static water head is available. In order to avert both of these failure mechanisms it is essential to control the elevation of the phreatic surface within the fill mass. This is usually achieved through campaigned filling and resting periods. The duration of filling and resting periods are often estimated using some form of stope drainage simulator. Due to the random nature of many characteristics that influence the fill mass hydraulic conductivity, simulation of hydraulic fill drainage can be difficult. The high consequences of inaccurate phreatic surface estimates combined with the high variability in drainage properties often results in operators taking a conservative approach to this modelling. This conservative approach can lead to significant delays in the filling cycle which can have a major impact on the productivity of many hydraulic fill operations and can often results in an unnecessary movement towards capital intensive paste fill systems. This paper presents a water management technique which combines a simplified drainage model with in-situ monitoring to provide a rational approach to water management. With an accurate drainage model filling operations can be carried out at optimum efficiency without compromising safety. The implementation of this strategy has lead to a significant increase in filling rates at a number of Australian filling operations. A brief case study from one of these sites has been presented.

May 1, 2007

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By M A. Notte

Sand casting of steel is a process that offers the greatest design flexibility and highest metallurgical versatility. However, competition from other methods of fabrication is quite keen, constantly forcing the steel casting industry to the production of better quality castings at lower costs. New methods and materials have been put to use in the last ten years by foundries everywhere. This paper, in the form of a progress report, deals with new methods, processes and materials used by Canadian steel foundries for regular production, as well as with developments still in the initial but promising stages. T HE casting of steel to shape is the most direct method of producing steel parts in their final form. It is a basically economical process both as to cost and production time; it is also a process that offers design engineers the greatest flexibility and highest metallurgical versatility. In North America, the steel casting market has a normal yearly sales volume of 1,500,000 tons. In decreasing order, the largest customers are the railroads, construction machinery and earth-moving

Jan 1, 1965

By Ian Orford, Ken L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper updates the principal author’s earlier publication, “Crushing Plant Design and Layout Considerations” (SME Mineral Processing Plant Design, Practise, and Control, 2002). It reviews the latest primary crushing and large cone crusher designs. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? The principal author’s previous paper in the year 2002 on ""Crushing Plant Design and Layout Considerations"" provided a detailed design and layout review for the design of primary and fine crushing (Secondary, Tertiary, Quaternary) mineral processing facilities. Some of the conclusions in this previous paper had predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available.The rock size reduction process, from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized into four (4) stages:• Stage 1: Mining ( Rock Breakage and Fragmentation)• Stage 2: Pre-Screening (Scalping)• Stage 3: Primary Crushing• Stage 4: Fine Crushing (Secondary, Tertiary and Quaternary; the crushers used in this stage are identified by the titles which usage has conferred on them)Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once a project's design criteria and the mine plan has been established, the actual circuit's utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stake holders in the selection of the final comminution circuit and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2016

By L. O. Thomas

THE Alaska Highway, in its course through British Columbia, traverses parts of two great physiographic divisions of Canada which are also distinctive geologically-the Cordillera in the western section and the Interior Plains in the eastern. The Cordilleran region in the portion of the Province with which this paper deals can be divided into four major northwest systems, known respectively from west to east as Coastal, Plateau, Cassiar-Omineca, and Rocky Mountains. The Coastal system consists solely of the Coast range except in the extreme northwest, where a part of the St. Elias range is included. The Coast range, characterized by mountains of great ruggedness,. is made up of an igneous complex of granitic rocks intruded chiefly as a great batholith. In places, spurs of these rocks extend into the Plateau heft, a partly mountainous tract largely occupied by quartzites, quartzose mica schists and their gneissic phases, and crystalline limestone with interbands and broad areas of chlorite, _hornblende, and sericite schists and bodies of intrusive granite gneiss-an assemblage of rocks known as the Yukon group. The Cassiar-Omineca system marks the divide between the Pacific and Arctic drainages. Its eastern boundary is well defined in the south by the Rocky Mountain Trench (see p. 229). The rocks of the system are, miainly, highly altered Palaeozoic sediments, but there are also Precambrian and Mesozoic rocks, the latter largely volcanic. The core of the system is granitic and there is evidence (see p. 221) to support the belief that it is of such a length as to constitute a batholith comparable to that of the Coastal system.

Jan 1, 1944

By Arthur Grounds

Historical In the course of a paper which is necessarily limited in length, such as the present one, it is obviously impossible to describe in detail the history, development, and present position of coal preparation in Western Europe. Great Britain has been blessed with large deposits of excellent coal of nearly every type, ranging from the high-grade anthracites of South Wales, which are characterised by their very low ash and volatile con-tents, to the superb coking coals of South Wales and Durham -probably the finest in the world -with their low ash and sulphur contents, the latter constituent often well be-low l per cent. Gas coals abound in Lancashire and Yorkshire, while coals from the East Midlands, Northumberland, and Scotland are excellent for steam-raising and other industrial purposes. The excellent quality of these various coals has, in years gone by, ensured ready .sales abroad and it is not surprising, therefore; that methods of coal preparation were largely developed on the Continent in an endeavour to upgrade the inferior fuels found there, so that the prepared product could compete with British coals on the European market.

Jan 1, 1951

By K. Meyer, M. E. Goddfellow

"At Teck-Corona Operating Corporation's David Bell Mine, a water quality management strategy is employed to produce both a chemically and biologically clean effluent prior to discharge to the environment.The strategy includes operating methods to minimize contaminants leaving the concentrator and an effluent treatment plant for cyanide, antimony, and heavy metal removal of concentrator, mine and site waste streams.Concentrator practices, the effluent treatment plant, process chemistry and the present day performance of the water quality management strategy are reviewed.INTRODUCTIONThe David Bell Mine is located in the Hernia gold camp 35 km east of Marathon, Ontario. The concentrator has a design throughput of 1,000 tonnes per day. ROM ore (-6"") is ground in a semi-autogenous mill followed by a ball mill, thickener, leaching, and carbon-in-pulp gold recovery unit operations. The concentrator flow sheet is shown in Figure 1."

Jan 1, 1991

By H. H. Fairfield

THE production and inspection of the materials of war involves thousands of observations. Logical action is generally based on the interpretation of many observations. The success of such action depends upon the accuracy of the observations and the soundness of the interpretation placed upon them. There are countless instances where the observer 'sees but perceives not'; that is, the significance of a group of observations is lost, due either to faulty interpretation or to no interpretation at all being placed on the results. This condition is being partly corrected in the United Kingdom and the United States (1) by the promotion of certain principles by Ordnance officials. The term Quality Control has been adopted to describe a system of studying and controlling industrial products by methods of handling observations. In these pages an attempt is made to outline in a non-technical manner some of the ideas used in the handling of observations. Of course the authenticity of the observations determines the worth of any decisions based on them. No matter how brilliant is the theory built on unreliable sampling, it is usually of little practical value. n some fields it is almost impossible to obtain observations free from bias. Let us suppose that observers of speed in miles per hour were available for judgment: (a) a bystander, (b) a motorcycle policeman, and (c) a motorist accused of speeding. The bystander might be unbiased but probably would be very inaccurate. The motorist is usually biased on the low side. The policeman is the only qualified observer and, if over-zealous, he might be biased on the high side. Conclusions drawn from large numbers of biased observations naturally would be of little value.

Jan 1, 1943

By A. Vien, B. C. Flintoff, R. P. Edwards

"A major thrust in industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements in control performance can be achieved by getting back to the basics.IntroductionEvery modem concentrator has a state-of-the-art computer control system in place. Several of these are contemplating installing, or have installed, advanced control systems, such as expert systems, but the foundation of their control system remains the PI controller. Although the authors are not aware of any survey or published information for the mineral processing industry, it is reasonable to assume that it would be similar to the pulp and paper industry. ""The average [pulp] mill has some 2000 control loops of which 97% use PI control. This means that PID, dead time compensation, adaptive controllers, specialized algorithms, ... , constitute only 3% of the installed base."" (Bialkowski [1992]).Bialkowski [1992] also stated that ""If you have been keeping score, only 20% of the loops surveyed actually decrease variability in automatic over manual mode of operation, in the short term."" He attributed the problems to: poor tuning (30% of all loops), control valve problems (30% of all loops) and process problems (20% of all loops). There appear to be a serious need to go back to basics and review the existing control system."

Jan 1, 1998

By Craig Naudé

"An enhanced gravity concentrator was installed in conjunction with an Intensive Leach Reactor at the Sadiola plant in Mali last year and commissioned in Dec 2007.There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every 10% of gold recovered by gravity, there was a corresponding 0.1% to 1% additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall 4% gain in plant recovery.With total gold recovery of 12% in the gravity section, grades are increased from 3.54g/t in the gravity feed to an average of 2 600g/t in the concentrator feed to the in-line reactor. The recovery of gold in the in-line reactor is in excess of 98.5%.This paper discusses the background to the project, the laboratory testwork prior to the equipment selection, the operational results of the system, as well as the benefits of the future application of high mass yield centrifugal concentrators in base metals, sulphides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.INTRODUCTIONBesides picking nuggets off the ground or out of riverbeds, gravity concentration is arguably one of the oldest methods of recovering gold. In circa 6000BC people discovered that gold can be found behind the rocks and in depressions of creek beds. By placing rocks in a stretch of channel with the proper slope the first sluice is built, probably around 4,000 BC, and this method is still practiced today."

Jan 1, 2009

By Chuan-Jian Zhong

Gold-based nanoparticles in the size range of a few nm have attracted increasing interests in catalysis, sensors and biomedical applications. The study of the unique catalytic properties of nanosized gold was inspired by the pioneering work of Haruta on the nanogold-catalyzed CO oxidation (1-4). There have been a number of excellent reports discussing both fundamental and application aspects of gold nanoparticles in catalysis (3-8). Our work reported herein is aimed at investigating the preparation and application of gold and its alloy nanoparticles for potential applications in fuel cell catalysis. Fuel cells operating by electrochemical oxidation of hydrogen or methanol fuels at the anode and reduction of oxygen at the cathode are attractive power sources due to their high conversion efficiencies, low pollution, lightweight and high power density. While methanol offers the advantage of easy storage and transportation in comparison with hydrogen fuel cell, its energy density (~2000 Wh/kg) and operating cell voltage (0.4 V) are much lower than the theoretical energy density (~6000 Wh/kg) and the thermodynamic potential (~1.2 V). The poor activity of the anode catalysts and inefficient activity or issue related to "methanol cross-over" at the cathode electrode are associated with the loss of about one-third of the available energy at the cathode and the other one-third at the anode. Extensive studies have been focused on Pt-group metals (Pt+Pd+Rh+Ru+Ir (PGM)) for both anode and cathode catalysts. A major problem is the poisoning of Pt by COlike intermediate species (9,10). Recently, oxide-supported gold nanoparticles in the <10 nm size range have emerged as one of the best catalysts for CO oxidation (1-3,11), and for water gas shift reaction in reforming stage using 5 nm Au on Fe2O3 (6). Gold and its alloy with other metals in the nanosize range present new alternatives (2,12). Whether the unique properties of gold nanoparticles can be exploited for addressing these problems is a focus area of our work. The ability to harness the large surface area-to-volume ratios and the unique surface sites of nanoparticles in <10 nm size range, especially in heterogeneous catalysis, constitutes a major driving force in fundamental research and practical applications of nanoparticle catalysts. It is this size range over which the metal particles undergo a transition from atomic to metallic properties. The understanding of factors controlling the morphological and surface reconstitution associated with such a size range is of fundamental importance to the ultimate exploration of nanostructured catalysts. We have been investigating the interfacial structures and properties of core-shell types of nanoparticles consisting of gold or alloy nanocrystal cores and organic monolayer shells that were prepared by twophase synthesis (13) and processing (14) protocols. Important attributes of such nanoparticles include controllable size monodispersity, processibility, and stability towards size- and composition-tunable catalysis (15-21). Some of these attributes were studied for understanding their electrocatalytic properties in the oxidation of methanol and reduction of oxygen, which are of fundamental interest to fuel cell technology.

Oct 1, 2003

By Michael Arriagada, Ivan Arriagada

"As mines return to shafts to economically exploit deeper reserves, two methods mine owners use to minimize short term costs are: sinking shafts in phases and refurbishing old, existing shafts. While there may appear to be benefits to utilizing existing infrastructure, often this is not the case, resulting in missed deadlines and added costs. Similarly, if proper long term planning is not executed when sinking a shaft in phases, additional costs and downtime will be accrued. This paper will take an in depth look at both of these options with an eye towards optimizing costs, minimizing downtime, and facilitating construction. INTRODUCTION With the onset of mechanized mining and large capacity trucks, many mines turned away from shafts and began to use ramps to haul ore to surface. However, continual exploitation of mineral reserves located closer to surface, combined with the subsequent unearthing of additional resources at greater depths, forced mines to go deeper and deeper to extend the life and keep the operation running. In shallow mines, hauling ore by truck was an economical option. However, as mines get deeper, driving ramps takes additional time, and hauling over longer and longer distances becomes less economic, both in terms of cost and time. For this reason Mexico, in particular, has seen a jump in the number of shafts which have been put into production, as well as having a number of shafts in different stages of development and still more in the conceptual stages. Many of the shaft projects in Mexico are being designed in phases, with the hoist and equipment purchased capable of reaching the ultimate planned depth of the shaft, but with sinking operations stopping short at an intermediate depth. A loading pocket is then installed to start exploiting mineral at this depth sooner, with subsequent phases planned for a later date using either a rock pentice or bulkhead to separate the sinking operations from the active shaft above. Currently, we are directly involved in two such projects which are actively being deepened, as well as having seen various others already reach completion. If done properly with the long-term plan in mind, sinking in phases can be a very viable option, allowing for faster production while fully utilizing the equipment at various depths. However, there are many issues which can arise when sinking a shaft in phases that if not properly examined and planned for from the outset, have the potential to eliminate the gains hoped for when it was decided to sink in this manner."

Jan 1, 2019

By Sengpasith Houngaloune

Arsenic, which is a toxic and carcinogenic element, causes serious environmental problems throughout the world. It is also known as a major contaminant in the non-ferrous mining and extractive metallurgical industries, thus its disposal is one of the most important environmental issues for the mining and metallurgical industries. In order to ensure a safe disposal environment for the final wastes, stabilization of arsenic has been studied extensively with various approaches. Solidification/stabilization (S/S) represents one of the most effective methods to reduce the availability of arsenic in soil and waste by transforming toxic or potentially hazardous phases into less hazardous ones. Cement based S/S processes could reduce the solubility of arsenic in solid waste, using inorganic binders such as cement, lime, and pozzolanic materials. A new tailings management technique, called cemented paste backfill (CPB), has become widely employed for improving mining techniques and for tailing storage purpose and this technique could also enhance arsenic stabilization, by fixing the contaminants in the binder matrix. Disposal of arsenic in the form of scorodite (FeAsO4?2H2O) has been widely accepted as currently the most suitable method for stabilization and the safest known storage material. The Bio-scorodite process has been reported to be more economic and environmentally friendly method than the chemical crystallization processes. Retention of arsenic by schwertmannite (Fe8O8(OH)6SO4), a metastable ferric oxyhydroxy sulfate mineral, has gained more attention in the recent years. Schwertmannite has a large specific surface area and high capacity to adsorb arsenic in solution. Several researchers have reported that the transformation of schwertmannite to goethite could be retarded by the presence of adsorbed arsenic; therefore schwertmannite might be viable alternative for long-term storage of arsenic. In this paper, various approaches used in arsenic stabilization are reviewed with emphasis on the development in the recent years.

Aug 1, 2013