Search Documents

By P. Brad Marchant

"To properly evaluate bioleaching as a commercial alternative for sulphide concentrate oxidation, to enhance cyanidation response, it was necessary to define and optimize critical operating variables outside of the laboratory under less than ideal conditions. A complete bioleach testing laboratory was installed at Equity Silver Mines to aid in pilot plant flowsheet development.A continuous pilot scale bioleach circuit was constructed to provide data for meaningful valuation of biotechnology on a plant scale. The important operating and design parameters for pilot plant testing are described. Plant scale feasibility and design considerations, to treat a refractory pyrite/arsenopyrite concentrate produced from flotation tailing, are discussed. 1.0 BACKGROUNDEquity Silver Mines Limited is located 37 km southeast of Houston in central British Columbia. A 70% owned subsidiary of Placer Development Limited, Equity is Canada's largest open pit silver producer. Ore reserves were estimated at 28 million tonnes grading 106 g Ag/t, 0.96 g Au/t, and 0.38% Cu from two pits, the Southern Tail and the Main Zone. Detailed geology and mineralogy has been described previously(1,2).The concentrator flowsheet consists of conventional crushing, grinding, flotation, and dewatering circuits processing 5 300 tonnes per day of new mill feed. The resultant Cu/Ag/Au concentrate is trucked to Prince Rupert for shipment to market. Mill tailing reports to a closed circuit pond from which mill process water is recycled. Details of the concentrator process have been reported( 2,3).Production in the Southern Tail pit, from July 1980 to March 1984, resulted in mill tailing averaging 0.9 g Au/t and slightly more than 20 g Ag/t. Historic data indicate that unrecovered gold is associated with arsenopyrite and silver losses with unliberated tetrahedrite or minor silve,, bearing sulphosalts. Main Zone mill tailing, which commenced production in March 1984, contains approximately 0.5 g Au/t which is probably associated by majority with silver bearing minerals and pyrite while silver losses, 30-40 g Ag/t, are associated with unliberated silver and antimony bearing minerals."

Jan 1, 1985

By R. W. Lawrence

"Biological leaching can be used to enhance the recovery of gold and silver from refractory ores, concentrates and tailings. The method liberates precious metals associated with sulphide minerals such as pyrite and arsenopyrite making them amenable to cyanidation. The chemistry and features of biological preoxidation leaching is discussed. A summary of the results obtained on various ores, concentrates and tailings is presented.INTRODUCTIONRefractory precious metal ores in which gold and silver are finely disseminated in sulphide minerals such as pyrite and arsenopyrite are becoming more important to the mining industry. This is due both to a depletion of simpler, free-milling ores and to a significant increase in the price of gold in recent years. Whereas many ores can be directly cyanided with gold solubilizations over 90% obtained, the refractory ores respond poorly to direct cyanidation and require decomposition of the precious metal-bearing sulphide minerals to increase recoveries.Decomposition of sulphides by oxidation prior to cyanidation can be carried out by several means. The oldest method is roasting which removes unwanted ore constituents by high temperature oxidation and volatilization. In Canada, for example, roasting is used at Giant Yellowknife (Connell and Cross, 1981). Another method gaining increasing acceptance is pressure hydrometallurgy which uses aqueous oxidation conducted at high temperature and pressure. Homestake Mining Company have recently completed construction of a plant incorporating pressure oxidation at their Mclaughlin property in California (Guinivire, 1984)."

Jan 1, 1985

By L. Tong, D. Robinson

"The stirred milling of nickel laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a netzsch™ lME4 stirred mill on siliceous goethitic, goethitic, and saprolitic nickel laterites. Tests on the -2,000 µm sample displayed the effects of selective comminution. The -38 µm product of grinding the -2,000/+38 µm feed confirmed the effects of selective grinding and nickel upgrading. Size classification followed by stirred milling is recommended for nickel upgrading. The energy requirement in the stirred milling was also investigated.RÉSUMÉ le broyage par billes de latérites comportant du nickel offre des possibilités d’amélioration de la libération et de la réduction sélective de la taille des minéraux nickélifères tendres dans les latérites. Des essais de broyage en vrac ont été effectués dans un broyeur à billes netzschMD lME4 sur des latérites nickélifères à goethite siliceuse, à goethite et saprolitiques. Des essais sur l’échantillon -2000 µm présentaient des effets d’une comminution sélective. le produit -38 µm de l’alimentation -2000/+38 µm confirme les effets d’un broyage sélectif et du rehaussement de la teneur en nickel. Pour améliorer la teneur en nickel, il est recommandé de classifier le minerai en fonction de sa granulométrie, puis d’effectuer un broyage à billes. l’énergie requise pour le broyage à billes a aussi été étudié."

Jan 1, 2015

By Neil R. Burns, Michael Doggett

Abstract - The Nanisivik mine offers a unique opportunity to examine the economics of a mining scenario from its original feasibility study through to closure. In the early 1970s, the Strathcona Sound project (exploration around the Nanisivik mine) had advanced to the point where a significant mineralized body had been defined and a feasibility study was initiated. The study supported development of the Nanisivik mine, with government investment in regional infrastructure, and the mine was constructed and operated for 26 years. Many elements of the feasibility study were difficult to estimate because the project was unique in its high Arctic setting. As a result, many differences were found when comparing the actual mining data to the feasibility study. The majority of these differences were the result of an actual mine life of 26 years instead of the planned 12.5 years. Most of the mining costs were higher than estimated and production occurred at a much higher extraction rate than planned. On a constant dollar basis, the metal prices were, on average, below the feasibility estimates. For the most part, these differences balanced out, with the actual mining being only slightly more profitable than anticipated in the feasibility study.

Jan 1, 2004

By A. R. Barnes, N. O. Lotter

Recoverable economic copper sulphide minerals such as chalcopyrite, bornite, chalcocite and covellite often occur together in varying proportions in the major copper-bearing ores, and have individual flotation requirements and characteristics. Pyrite also occurs in these ores to varying extents as the sulphide gangue, and is problematic because of its natural tendency to float quickly and easily. In a bulk sulphide float, selectivity against pyrite is desirable, particularly if it does not host other paymetals such as gold or silver. At the same time it is a requirement to float all of the copper sulphides despite their electrochemical differences. The electrochemistry and semiconductor properties of these minerals are reviewed, together with implications for flotation with and without collector addition. Mixed collector systems for the improved flotation of these sulphides are proposed as a solution. The use of xanthate and dithiophosphate in the collector suite allows the co-existence of dixanthogen and free dithiophosphate radical because the latter has a higher redox potential requirement than xanthate to oxidise to the dithiolate. Because some of these minerals require dixanthogen, and others, free thiolate, to generate surface hydrophobicity, a bulk flotation of all the species becomes possible in the overlapping area of Eh and pH between the two dithiolate equilibrium lines on the Pourbaix diagram. The arsenic-signature copper minerals are added to the study, since many copper operations encounter arsenic as a penalty element in the saleable concentrate. It is shown that the addition of arsenic to the copper and iron sulphides alters the semiconductor and electrochemistry properties, and in turn, its flotation characteristics. The degree of mineral association and liberation between these minerals can be a complicating factor due to textural associations, and should also be considered in the process as a next step.

Jan 1, 2016

By D. R. Winchester

"I wish to thank you and your organizers for inviting me to address you at this point in time when we are all concerned for the future of the mineral industry in Canada.My topic ""Some Initiatives of Government Assistance to Industry Applicable to Mineral Processing"" is purposely limited in scope. To cover the entire range of initiatives in detail would take me all day, and at best, would be a mere recital of program titles, and a one sentence summary of the contents of the program. As you know, OREE or Regional Economic Expansion, is in the process of being amalgamated with elements of the Department of Industry, Trade and Commerce. We will become Regional Industrial Expansion or ORIE. If the name Canada Dry becomes popular, I don't think we will object as we hope to become a good mixer. The entire departmental thrust has been re-evaluated, and is in the process of being re-constituted to better serve the nation, and industry as a whole. Amalgamation of the industrial, trade promotion and marketing support skills of IT&C, with the regional development orientation and decentralization program delivery mechanisms of DREE, will, it is believed, provide better support to industry on a national and regional basis."

Jan 1, 1983

By G. D. West, J. D. Purdue

"Marked Ball Wear Testing (MBWT) employs identified grinding balls which are placed in an operating mill for a period of time, retrieved from the mill, and then measured to determine the amount of wear experienced. This is an excellent method to evaluate the relative differences in the wear rates of various grinding ball materials and/ or manufacturing process variables simultaneously and under actual production milling conditions. This paper outlines the methods of ball identification, testing and evaluation procedures and discusses the strengths, weaknesses, and proper application of marked Ball Wear Test results. INTRODUCTIONThe consumption of grinding media in the mineral processing industry represents a substantial cost to the comminution process. Grinding media is most often found to be the second highest consumable cost next to energy. To determine the selection of the most cost effective media, one must determine the specific wear mechanisms present in a given grinding application and decide which media system addresses these mechanisms most economically.A MBWT has definite advantages over other methods used to evaluate the relative consumption rates of grinding media. It allows the comparative testing of a large number of different ball types under identical operating conditions in a very short period of time. In addition, production wear rates can be accurately predicted directly from MBWT results. Typical MBWT test periods are in the order of 350 to 700 operating hours for high wear rate application and upwards of 2000 or 3000 hours for low wear rate applications. These times are much less than the 5000 or more hours required to purge a mill of the incumbent ball charge (to convert it to the test ball) and then provide even a minimal test period in which to conduct a full production test, for just one type of ball. Under production test conditions the evaluation of competitive product or the development of improved grinding balls is necessarily slow."

Jan 1, 1991

By Peter A. Hacquebard

"Two continuous coal zones occurring in a 2500f t (762 m) thick section of the Upper Carboniferous Pictou Group (Westphalian C and D) have been encountered in five offshore wells drilled f or oil and gas in the Gulf of St. Lawrence. They correlate, by means of fossil spores, with thick coals of the Mabou and Inverness coalfields situated at the eastern margin of the Basin. Therefore, the presence of a large submarine coalfield of at least 18000 sq mi. (46 620 km'] is indicated. This compares with an estimated size of 14 000 sq mi. (36260 km' ) for the Sydney Coal Basin.Accessibility is provided only by the small onshore parts of the Mabou and Inverness fields, because farther offshore the coals lie too deep to be mined (below 4 OOO f t ([ 219 m)).Two near-shore coal exploration wells indicate that at Mabou Mines the younger Inverness coals occur at a mineable depth to at least 5 km from land. A structure contour map of this area shows a reserve of 125 million tons in two Inverness equivalent seams that are 8.5 ft (2.6 m) and 4.5 ft (f.4 m) thick. The Mabou coals, however, reach too great a depth close to shore to possess mineable resources.A structure contour map of the Inverness submarine area, based on mine data and one off shore seismic profile, indicates inferred mineable resources of 160 million tons, in two seams that are 7ft (2.1 m) and 4.5 ft (f.4 m) thick . A detailed deep seismic survey will be necessary to substantiate the structure and resource estimates"",Maceral and coal quality percentage diagrams of five column samples of these seams (the 7 Foot and 13 Foot Seams of Inverness Equivalents) show a bright banded coal, high in reactive macerals, which will produce a weak coke unsuitable f or metallurgical purposes. A thermal coal with a rank of H. V. ""B"" Bituminous (0.64% Ro) is present, averaging 12000 btu llb (6 660 kcai/kg), 10% ash and 6% sulphur, of which 60 to 80% is derived from pyrite.Microlithotype profiles of the major Mabou and Inverness coals show characteristic successions that can be used f or seam identification and proved valuable f or structural interpretations.The time of faulting in the major fracture zone on the eastern margin of the Gulf of St. Lawrence Basin has been deduced from coal rank variations. It occurred in pos tPermian, probably Early Triassic time."

Jan 1, 1986

By Paul Staples, Fred Woodcock, Robert Grant, Mike Cooper

"Noranda's Brunswick Mining Division, near Bathurst, New Brunswick, processes 10,500 TPD of complex Cu-Pb-Zn bearing ore. Brunswick uses conventional rod and ball milling techniques to achieve a flotation feed size of 75% passing 400 mesh. Over a two year period, testwork was performed using a Marcy pilot plant ball mill to assess the impact of several key variables on secondary grinding efficiency. Four graded mill charges were used to compare balls and slugs at 25 and 29 mm sizes. Data was evaluated by determining grinding rates using a commercially available steady state simulator. Results were critical in Brunswick's efforts to achieve finer grinds while minimizing cost per tonne.IntroductionBackgroundThe Brunswick orebody is an extremely fined grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite.Size reduction at Brunswick is performed by three separate parallel lines consisting of rod mills, primary and secondary ball mill circuits, all in series. The line 3 grinding circuit is presented in Figure 1."

Jan 1, 1997

By Ralph L. Rutherford

Geologists or mining engineers familiar with geology are frequently requested by mine operators to give correlation in-formation regarding some mining property with respect to an adjacent area on one at some greater distance. It is the object of this article to mention a few of the difficulties involved in securing this information and to point out some of the salient factors upon which correlation is dependent. In view of the nature of the following discussion, a brief statement of the general character of coal formations .. seems appropriate. Coal formations, by reason of their environment of deposition which is in fresh or brackish water, exhibit the features common to continental deposits, in contrast to those of marine deposits. Such deposits are characterized by rapid variation in thickness and in lithological character both later-ally and vertically. (Plate 1 A). They consist essentially of sandstones and clay shales with all gradations between them, and also a few beds of coal and frequently some conglomerates.

Jan 1, 1924

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By Renaud Adams, Vladimir Salatic

"The El Mochito Mine located in Honduras, Central America, has produced lead, zinc and silver in concentrates since the 1950s. The paper discusses changes made in both lead and zinc circuits to reduce costs while maintaining production during the recent period of low metal prices.The intent of this paper is to show that sometimes thinking “outside the box” is beneficial for progress. Also, in striving for better metallurgical results we should not forget the basics of flotation. Sometimes the latest trends may not be applicable to the ore we are treating and may not meet the operating cost constraints.A major beneficial impact on El Mochito metallurgy was achieved when the overall grind was coarsened, eliminating the significant percentage of slimes. Switching from two parallel twostage grinding circuits to one circuit with three-stage series grinding has resulted in a significant reduction in power and steel consumption. With minor layout/reagent modifications, both lead and zinc circuits gained not only in retention time but as well in producing better grade products.Of course, the challenges are still there; they exist and only with the full support of operational data collection and metallurgical laboratory investigation success can come. That is why, we as professionals, can never stop in trying to make the most of what we have.INTRODUCTIONThe El Mochito Mine is owned by American Pacific Honduras S.A. de C.V. (AMPAC) a subsidiary of Breakwater Resources Ltd. Of Toronto, Canada. The mine is located in western Honduras, approximately 220 kilometers northwest of the capital city, Tegucigalpa and 90 kilometers south of the country’s second largest city, San Pedro Sula. The mine began operating in 1948 and to date has produced more than 19 million tonnes grading 240 g/t Ag, 3.5% Pb and 7.4% Zn. Production in 2005 was 700,190 tonnes grading 87 g/t Ag, 1.85% Pb and 6.61% Zn.Decreasing metal content in the ore followed by the lowest zinc price on the market in the last 15 years (see Figure 1) has reduced the cash flow and endangered to stop the operation."

Jan 1, 2007

Keeping the sediment on the mine site and out of the water course is essential from the regulatory, environmental and sustainability perspectives. Regulation of this aspect of mining is embedded in environmental legislation and government receiving water quality standards, and government control has apparently been considered to be the most appropriate method to define mine site discharge standards and the environmental implications of sediment in downstream watercourses. A literature search for guidelines for the site specific design and operation of sediment ponds treating mine site runoff to remove total suspended solids, turbidity and flocculant-induced toxicity, revealed little information on the mining industry?s and government?s roles in defining the ?how to achieve? related to sediment pond design. Is there a need or reason for an industry-driven leadership to clearly define the ?how to? keep the sediment on the mine site and out of the water course? Currently, this issue is addressed in Canada by a federal mining regulation for metal mines which specifies discharge quality for sediment. This paper focuses on the method used in British Columbia, Canada, to regulate and provide a scientific methodology to control the discharge of sediment from mine sites. Management plans relative to this topic are discussed and are considered to have value from the exploration, construction, operation and the onset of closure phases. In addition, the balance and linkage between the erosion control management plan and the sediment pond management plan are discussed in terms of how they may be designed to complement each other to lower the risk of exceeding discharge and receiving water quality standards. If there were an industry-driven standard, or guidance document relative to addressing sediment release, it would benefit mining companies by eliminating the repetitive analysis of this topic for each new mine, mine expansion, and mine modification; also, government may often replace certain aspects of permitting with a regulation, if there is a government/industry established standard defining Best Achievable Technology (e.g. the Canadian Metal Mining Effluent Regulations).

Aug 1, 2013

By Pierre Boileau

Outline ? Who are We? ? Canada?s GHG Emissions 1990 - 2000 ? Emissions from the Petroleum Sector ? Emissions from Petroleum Exports ? Emissions from Manufacturing Industries ? Emissions from Mining and Metallurgy ? Conclusions Greenhouse Gas Division Key Functions: ? National GHG Inventory Report, Emission & Removal Trends Analysis, and Indicator Fact Sheets ? Scientific and Engineering Guidance, Technical Advice, Data Quality Assurance & Quality Control and Methodological/Data Development ? International Negotiations (FCCC) & scientific/technical guidelines (IPCC & ISO) ? Expert Review Teams (ERTs) ? Outreach ? GHG Verification Centre ? Clearinghouse ? Protocol Development

Nov 1, 2002

By G. M. Behrend

"AbstractMeasurement and control systems in minerals processing plants are usually well thought out and designed. The criteria and design parameters have been interpreted correctly.However, these systems often fail to perform satisfactorily or break down altogether as a result of in-plant conditions which are unpredictable and over which the instrument systems designer has no direct control. The foresight necessary to anticipate the problems and allow for them in the systems design can only be generated by experience.This paper lists the most common of these problems and offers practical methods for their solution. It then follows with an analysis of instrument installation practices and comments on special points that need watching.Finally, instrument maintenance is discussed with a view to achieving good maintenance at the best possible economy.Good MeasurementGeneralTHE MINES and mineral processing plants of the nineteen seventies, after decades of sensible caution, have now committed themselves to extensive automatic control. X-ray analyzers are freely specified. Sample acquisition systems are efficient and automated, computers are reliable and relatively cheap, and computer control systems in conjunction with the new analyzers are operating in a good many plants and are proving to be profitable.The sight of shift foremen and floor operators assembled in front of a TV-tube and taking a computer data display as gospel truth is quite common now, and yet was quite unthinkable only ten years ago."

Jan 1, 1977

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By E. Esponosa-Gomez, J. A. Finch, A. R. Laplante

"Water quality plays an important role in oxide flotation. The effects on selective flotation of fine (1-16 um) pyrochlore of two types of water used at the Niobec concentrator, potable and plant recycle, were assessed. Several pyrochlore collectors and silicate depressants were tested. Water effects were different for each mineral-reagents) combination. In general plant recycle water decreased selectivity and increased reagent consumption. Interpretation of results is given in terms of electrokinetic effects, hydrolysis of cations, and mineral-collector interactions. Two techniques of treatment for plant recycle water, cation precipitation and zeolite adsorption were assessed. The former was found to be more effective under the tested conditions but recycle water continued to give poorer selectivity than the potable.INTRODUCTIONWater quality plays an important role in selective flotation. Specific effects have been reported by many workers (1-6) and in general the better the water quality the more selective is flotation. Water composition depends on origin and the minerals being processed. For example pulp containing salt-type minerals (calcite, apatite, dolomite) will contain more Ca and Mg cations than that from a sulphide deposit. Another source of water contamination is the flotation reagents added to the pulp, particularly if water recycling is practiced."

Jan 1, 1986

By Svato Prochazka

Content: ? commonly used drive systems ? drive system efficiency ? introduction to SR technology ? SR drive system advantages Commonly Used Feeder Drives Technologies ? VFD + induction motor ? hydraulic drive + hydraulic motor SR drive + SR motor

May 1, 2010

By D. M. Doyle

"A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc. over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study 11rogresses through monthly, daily and finally, into quarter hourly data, the variations become more evident and most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program.The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Sudbury Operations, the material and control equipment, the commitment, the new energy accounting practices and lastly, the policies. Examples of successful energy conservation endeavors include automatic peal electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailmen: of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and if necessary, immediate reporting of energy and energy per unit of production information. The program so reported at Falconbridge’s Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0 million dollar annual energy account."

Jan 1, 1979

By S. Deonarain, L. S. Schultz

"This paper details the process and methodology followed to rehabilitate a rectangular ventilation shaft, situated in the Free State region of the Witwatersrand Gold Fields in South Africa. The shaft consists of seven compartments where self-mining of the sidewalls had taken place and damage to the decayed steel work in the shaft had taken place, thus limiting access down the shaft. The paper will provide some insight into the successes and challenges encountered during the project and may provide some learnings for future projects of a similar nature. INTRODUCTION The ventilation shaft forms part of the Phakisa Mine, situated in the Welkom area of the Free State province of South Africa, and is located in the Southern part of the Witwatersrand Basin, one of the world’s largest known and richest gold deposits (Figure 1).As is typical in South African gold mines situated in the Witwatersrand basin, the shaft is 1 770 metres deep (below collar). The shaft was sunk during the early 1940’s and comprised a rectangular shape with 7 compartments, used for both rock hoisting and men and material winding, respectively, with a single lift “Mary-Anne” compartment. Early in 2003, the mine decided to change the shaft from a downcast hoisting shaft to an up-cast ventilation shaft. The conveyances, ropes, winders and headgear (head frame) were removed and replaced with a high volume fan delivering 323m³/s of air at a pressure of 4.2Pa on surface. The up-cast velocity in the shaft was 6.5m/s, however this reduced significantly with the scaling of the shaft and the restrictions at shaft bottom. Although Harmony had converted the shaft from a downcast service shaft to an up-cast ventilation shaft some years back, the shaft steel work in the barrel of the shaft was left intact. Over the years, the steelwork in the shaft had decayed (rust and grime) and portions of this steelwork fell down the shaft. Concurrent with the decaying steel work, portions of the shaft lining had collapsed and it was getting progressively worse."

Jan 1, 2019