Search Documents

Water is important commodity in the mining industry. Water is used in the many stages of mining from the exploration stages and drilling, to mine development and operation and finally throughout mine rehabilitation and post mine activities. With the use of water throughout the life span of a mine, its management is an important component in the operation of any mine. Unfortunately the use of water within the operations can be one of the major sources of pollution generated from a mine. Such contamination can occur via numerous mechanisms including ground water flow, over land flow and accidents. Contamination may occur in any stage of mining operations, for example a leaking or failed tailings dam. With the above in mind, the paper presented will focus upon the use and management of water in the mining industry: ownership rights of water û common law as well as legislative rights; a review and analysis of the existing Queensland legislation and its mechanisms for the protection of water pollution from mining operations; and conclusions drawn from the paper relating to the Queensland legislation.

Jan 1, 2003

By D von Horn

Mineral sand orebodies are typically mined for their TiO2 content. Increasingly over the past 30 years, the major mineral focus has shifted from natural rutile to ilmenite and an acceptance that the latter generally needs some form of upgrading for economic conversion into TiO2 pigment. This upgrading obviously has a cost, and in conjunction with diminishing mineable feed grades, results in higher cost TiO2 units for chloride route Pigment Plant feedstocks. The net cost of feedstock can be significantly influenced by the recovery and sale of accessory minerals and by-products from the processing chain to the extent that some producers have the potential to achieve a zero net cost. Whilst slagging plants typically reduce net cost from rutile, zircon and pig iron revenues, operations supporting Becher type synthetic rutile operations have been limited to revenues from rutile and zircon only. A range of alumino silicate minerals show industrial potential, as does activated carbon, iron oxide and gypsum, by-products of the synthetic rutile process. Tiwest is a good example of a company maximising revenue from the accessory minerals as well as from by-products of the synthetic rutile process.

Jan 1, 2001

As Coal Mining Areas develop, problems relating to strata control increase. The "easy" coal has been extracted and the future development lies in the direction of greater depths of cover and more difficult strata conditions. To provide solutions to the problems encountered the techniques of constructing and testing physical models have been developed and refined. With a sound knowledge of model theory allied to practical experience, mining research engineers use physical cemented material models to examine, assess and solve mining problems relateu to strata behaviour and environment. For a model to provide the answer to a particular mining problem it is essential that as much information as possible be obtained from the mine or area of a mine which the model is to represent. Details relating to the strata, geological malformations, and the stress environment must be collected and collated to ensure reliable results.

Jan 1, 1976

By Conley R, Payne I

The Vickery Coal Mine commenced open cut mining operations in May 1991. All overburden and interburden is drilled and blasted for excavation by dragline or hydraulic excavator. The mode of operation adopted from the feasibility studies requires that throw blasting of the overburden be used to assist dragline productivity.This paper reviews the development of the drilling and blasting practices with particular emphasis on the throw blasting of the overburden and optimisation of costs. This review includes analysis of the pre-production drilling and blasting feasibility studies by comparison with actual results.

Jan 1, 1992

By N Vagias, R Shaw, M Coghill, W Easman

Rio Tinto Technology and the Rio Tinto Foundation for a Sustainable Minerals Industry have funded the development of a practical floating module that can reduce water losses through evaporation from water dams at mining and mineral processing facilities by about 75 per cent. The modules, which are also suitable for use by farmers and communities, were designed for easy deployment, to allow the water to æbreatheÆ, harvest rainfall and resist wind speeds of more than 100 km/h. A large-scale demonstration trial will be conducted at the Northparkes Mine, located near Parkes (New South Wales, Australia). The objective of the trial is to demonstrate to Rio Tinto business units, community, farming and government groups the moduleÆs operating costs and water saving potential.

Jan 1, 2006

By Kewu W

Kaolin used as an industrial mineral, especially that in the paper-manufacturing industry, must be of fine size, with high brightness, a low impurity content, and good crystal shape. However, in most kaolin deposits there are various impurities which have a very bad effect on the quality of the kaolin. Therefore, it is necessary to remove these impurities from kaolin ore. Owing to their similar surface properties, the separation of kaolin and iron oxide minerals, especially microkaolin and iron oxide minerals, has been regarded as difficult. The iron oxide minerals often intergrow with kaolin in fine and complicated forms, such as thin films, which make separation difficult. In order to overcome this difficulty, many workers have suggested various treatment methods and obtained great success. Based on research work by Fuerstenau (1980), Huang, Li and Hu (1984), Hui and Wei (1991), Shergold (1978), and Zambrana et al (1974), we have investigated a two-liquid flotation technique for iron removal from kaolin and obtained some success.

Jan 1, 1993

Classifications of Ni-Cu deposits are based on petrology, geochemistry and the geotectonic setting of host igneous bodies (Naldrett and Cabri, 1976; Besson et al, 1979; Nadrett, 1989). The four major classes in Naldrett's (1989) division rest on the geotectonic setting of the igneous complexes and the classes are further subdivided on the basis of the petrology and geochemistry of the intrusion. A more common subdivision of mafic and ultramafic igneous rocks is based on the environment of rock-forming processes, endogenic or exogenic, intrusive or extrusive, and this subdivision has been applied, in practice, to the classification of sulphide Ni-Cu deposits, too. The extrusive deposits, Class I in Naldrett's (1989) classification, are directly related to volcanic processes whereas all the others refer to the intrusive environment. This paper looks at the differences between the extrusive and intrusive groups of Ni-Cu deposits and presents generic, genetic and structural features of the intrusive group.

Jan 1, 1996

There is considerable variability in the level of detail incorporated in prefeasibility studies relating to mining developments. Hence, when undertaking a review or audit, it is critical to attempt to ascertain at an early juncture precisely who has compiled the various facets of the study, for what purpose it was intended and the terms of reference given to the authors. Likewise, when commissioned to undertake an audit it is preferable to have proper terms of reference and to be aware of the purpose to which the audit will be put.These factors will influence the degree of detail an auditor would expect to find in the study and consequently, the degree of effort/time required for the audit process. In most instances audits do not imply recalculation of the entire study or modifying it in anyway, but involve an overall assessment of the methodology used, combined with spot checking of detail. One of the most difficult aspects is to determine a realistic order of accuracy for the overall study when the accuracy of the individual components may differ markedly.

Jan 1, 1990

By L D. Meinert

Skarns typically are zoned and the deposit- or district-scale zonation pattern is an important tool in exploration for skarn deposits. Zonation in individual deposits has been described in many publications, and the general zoning patterns have been summarised by Einaudi, Meinert and Newberry (1981), Meinert (1997), and Meinert, Dipple and Nicolescu (2005). Although zonation is present in most skarns as the result of a basic process of transferring heat and fluids from magmas to wall rocks, the specific zoning pattern in each skarn may vary greatly. For example some zones may be missing entirely or multiple zones may be telescoped. Such variations can be caused by several factors including depth of formation, magma composition, timing of the exsolution of magmatic aqueous fluids, redox state of the magma and redox state of the wall rocks. To use zonation as a predictive tool in skarn exploration, all the controlling factors have to be considered. In this study, we discuss some of the factors that may affect the zoning patterns in Ca skarns. Magnesium skarn has dramatically different mineralogy and is not discussed here. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

1991 New Zealand Branch Annual Conference û Appendix

Jan 1, 1991

By Yamakita T, Yoneoka Y

The Chigirishima Smelter of Toho,Zinc Co., Ltd. is the largest independent custom lead smelter in Japan and produces about 60,000 tonnes/yr of electrolytic lead. The quantity of slag produced by blast furnace is approximately 65,000 tonnes/yr, 30,000 tonnes/yr of which is sent back to the sintering plant for mixing with lead concentrates. The remaining slag used to be piled up at the yard until the operation of the fuming plant started in July 1977. We examined the slag fuming process with the purpose of achieving: 1) Improvement of the operating results by recovering zinc and lead from blast furnace slag. The lead content in slag at Chigirishima is slightly high, because the height of blast furnace shaft is low and consequently the quantity of sinter smelted per area at tuyere level is rather large. 2) Production of a salable slag as raw material for cement by lowering zinc and lead content in slag.

Jan 1, 1980

My paper presents a discussion of the legislative and departmental requirements in connection with the acquisition of exploration rights for minerals (other than petroleum and coal) in the Independant State of Papua New Guinea, the Solomon Islands and Queensland and he practical problems associated with land entry and land ownership associated therewith. In general there are many similarities in the methodology and philosophy behind the legislation in each country and the contractual requirements established thereby between the exploration company (the explorer) and the government and the mines department or equivalent in each place. There are also a number of differences. I have prepared the paper on the basis that my audience will largely consist of -experienced explorers and the paper is intended to act as a brief refresher and a guide to the philosophy and the practicalities behind the legislation and practices in ground entry in each case. I will deal in turn with New Guinea, the Solomon Islands and then Queensland.

Jan 1, 1987

In those days no one worried - there were plenty of other things to do. But in'these days it is different. Everyone worries- and. because there is so much worry, emotion has entered the picture. And, worse than that, capital is being made in political circles. People who were quite unaware, five years ago, that any problem existed, have now become experts on the subject, and shout to high heaven that something should be done - and yet they go on using the leaded high octane petrol they deplore so much. And even scientists, who should know better, adduce only such evidence as fits the argument in hand. And the Press is not without blame - some of its reportings is open to serious question, whatever may be the excellence of its motives. The point is made that one should know what one is talking about. And make sure that the evidence quoted is fact - and make sure too, that all the evidence is used, not only that which suita the argument.

Jan 1, 1971

I am honoured, deeply honoured, that so distinguished a group has assembled to acknowledge the signifi- cance of the work of my Melbourne flotation research laboratory, to review progress since Principles of Flotation (Wark, 1938) was published, to highlight the present state of knowledge, and to point the way for future research. The flotation research which began in 1929 was sponsored by a group of mining companies2 at the instigation of Harry Hey of the Electrolytic Zinc Company of Australasia Limited. There were never more than three of us work- ing in rather cramped conditions in a laboratory made available by the Department of Chemistry at the Uni- versity of Melbourne, but what we lacked in space was more than offset by a freedom unparalleled in indus- trial research in Australia at that time. I pay special tribute to my first colleague, Alwyn Cox; to my wife who worked with us for several years; and to Keith Sutherland who followed Cox in 1936. They were my sole colleagues up to 1938 when Principles of Flo- tation (Wark, 1938) was published.

Jan 1, 1984

Investment decisions in the Australian mining industry are often made without awareness of the impact of risk on project outcomes. A fundamental change in thinking is required to move away from the traditional attitude of æcushioning the blowÆ towards a measured approach to project risk. Such an approach involves quantifying and understanding project uncertainty so that investments may be shielded from downside risk while at the same time exposed to upside potential. Communication and collaboration between study teams and corporate financial managers must be improved before the industry can improve its project investment record. Monte-Carlo simulation provides a way to quantify and understand investment risk, but its accuracy depends on how well the variability of input parameters is estimated. Research in this area is currently centred on quantifying uncertainty in mineral resource estimation using new conditional simulation techniques, but a less-rigorous method can be applied in practice to begin the education process and develop the required awareness at board level.

Jan 1, 2003

By Abdurazakov A, Avrakhov A, Solozhenkin P

The flotation properties of acetic acids modified by xanthic and dithiocarbamic fragment in regards to copper and ferrous minerals and their noble metal containing ores have been investigated. The effectiveness of the co-using of these reagents with xanthates and dithiocarbamates has been shown, ie using of proposed reagent regimes for the flotation of Au-containing ores increases gold recovery by 4.2 - 4.7 per cent, and in the case of flotation of copper Re-containing ores copper recovery increases by 3.3 per cent, rhenium recovery - by 15.5 per cent. The mechanism of the action of these reagents has been explained by the data of UV and ESR-investigations of their sorption on mineral surface. The information on structure and properties of co-ordination compounds of some metals with (Diethyldithiocarbamato) acetic acid were used also for the explanation of flotation mechanism.

Jan 1, 1993

By Restarick CJ

A compound cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone, has been used for coal slurry sizing experiments in the range approximately 100 to 300 micrometres. An important feature of the system is the ability to adjust the cut size of the separation over wide limits by adjustment of the flow control valve. Results have been compared with typical fine screening operations. Under roughly equivalent conditions the compound cyclone system can achieve better elimination of extreme fines, but is not as sharp as the screen for coarser size cut-off. Simulations of systems involving combinations of the cylinder-cyclone system with screens indicate that the advantages of both sizing devices can be combined to yield accurately sized products for fine coal cleaning, at much less cost than using screens alone.

Jan 1, 1984

By Morrison RD, Simmons CJ

A bewildering array of process control instrumentation is currently available for mineral processing plants. For sequencing control, special purpose microprocessors or the process control computer can be used. Where continuous control is required, then the choice is between pneumatic controllers, electronic controllers, shared display micro- processor systems and direct digital control. The benefits of each system are discussed and the advantages of using direct digital control in mineral processing plants are outlined. The factors which need to be considered when selecting control systems for new plants are listed. Instrumentation systems designed by Fluor Australia are used as case studies to illustrate the selection process. For established plants, conversion to direct digital can be advantageous, and case studies are given. However, replacement of existing systems requires justification based on a productivity improvement which will allow the control equipment to be paid for within a specific time period. Productivity improve- ments maybe assessed in terms of increased

Jan 1, 1978

Mount Isa Mines Limited has been mining silver-lead-zinc ore at Isa Mine for 60 years. Mining methods have evolved continuously, and current production rates of 4.7 Mt/yr are obtained from a combination of sublevel open stopping, cut and fill, and benching methods. In the near future, orebodies mineable by open stoping will be gradually depleted, and the relatively new benching method will be further refmed to replace cut and fill methods wherever possible.

Jan 1, 1993

By McKee DJ

Many workers have observed an inverse relationship between final concentrate grade and valuable component recovery achieved by a flotation circuit, i.e. an increase in either grade or recovery may only be achieved at the expense of the other. The relationship is termed a "grade-recovery" curve and, in theory, limits the separation obtained by the circuit. However, circuit surveys in a nickel concentrator indicate that the operating "grade-recovery" curve of a circuit is not only determined by the nature of the ore and the circuit operating conditions, but also by the circuit design, particularly in terms of stage capacities. The surveys show that different capacity circuits can produce different operating curves for the same ore, and that capacity reallocation between stages has the potential to improve both grade and recovery. In particular, the relationship between circuit design and operating curve position is shown to be a function of the circulating loads generated by the circuit design, balancing the beneficial effects of recycling material against the proportion of plant capacity consumed by recycling.

Jan 1, 1986